801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com E-mail:
[email protected] S6100 SERIES REVERSIBLE PANIC/FIRE EXIT
RIM DEVICES INSTALLATION INSTRUCTIONS
These instructions are presented a in step by step sequence. Please read it through before installation. Note: The dimensions of the Template are shown in inches. See attached page for the Metric Conversion Table for millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd
Rev -
12/10
Page 1
End Cap Bracket
A. DESIGNATION OF PARTS
Chassis
End Cap
Dogging Device (Fire Exit Hardware is not Equipped with this device)
Chassis Push Bar
Chassis Cover
Strike Latch Assembly
B. TYPE OF INSTALLATION A. Single Door
B. Double Door with Mullion
TRIM
DOOR
TRIM
C. Double Door without Mullion
TRIM
DOOR
TRIM
DOOR
DOOR
DOOR
DOUBLE DOOR STRIKE
MULLION
2-7/16”
2-7/16” CL
2-7/16” CL
CL
C. MARK POSITION FOR INSTALLING 1. Mark the center line of device by drawing a line CL OF across the door and stop 40" above the finished floor DEVICE as shown at right. 2. Prepare door for you specific device per supplied template. 3. Drill holes as marked on door and jamb or mullion.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd
Rev -
TRIM
12/10
Page 2
INSIDE FACE OF DOOR
JAMB
CL OF STRIKE
40" to Finished Floor
STOP LINE Jamb
D. INSTALL STRIKE TO FRAME 1. Place strike over the drilled holes, and attach it to the jamb or mullion with the supplied screws. 2. If installing with a vertical rod device for double doors, and additional Double Door Strike must be used in place of the regular strike provided.
Door CL of Device Strike Site Strike
E. IF CYLINDER IS INCLUDED WITH THE DEVICE 1. Drill one 1-3/16" diameter thru hole for the cylinder/bracket plate. 2. Insert cylinder and cylinder collar from outside of door. 3. Place bracket plate on inside of face of the door. 4. Put two cylinder mounting screws through the bracket plate and into the cylinder. 5. Cut the cylinder mounting screws and tailpiece to the required door thickness at break-off points, then fasten screws.
Cylinder mounting screws
1/4” Outside face of door Cylinder bracket plate
Cylinder Collar Rim Cylinder
Inside face of door
Tailpiece projection Cylinder Actuator shaft (Tailpiece)
F. INSTALL OUTSIDE TRIM Mark and drill holes for the outside trim (see trim instructions). Latch Assembly
E. INSTALL DEVICE BODY 1. Remove chassis cover from latch assembly and end cap from end cap bracket. 2. Place the device horizontally over the drilled holes and attach with the supplied mounting screws. Bolt device chassis to trim with sexbolts (if required). 3. Make sure cylinder or trim actuator shaft (tailpiece) can insert into device cam concentrically (see device cam at right). 4. Install end cap bracket on device, then screw to door. 5. Tighten all screws or bolts.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd
Rev -
12/10
Page 3
Device Cam
Insert Trim Actuator Shaft Into device cam “+”.
Mark mounting holes through End Cap Bracket after device is level A NOTE: The Device bar has 3 different lengths; Standard 3' Door Device = Approx 33" Standard 3.5' Door Device = Approx 40" Standard 4' Door Device = Approx 44"
Latch Assembly
The bar lengths of devices are pre-cut for 36", 42" and 48" wide door, no additional cutting is necessary. If narrower door installation is needed, cut device at the “A” location, to door width minus 4" to fit properly.
H. INSTALL COVERS
1. Test push bar operation before installing covers: a. No Trim: Latch bolt is retracted by push bar inside. b. With Trim: Latch bolt is retracted by push bar inside, key or lever/knob outside. c. Dogging: See dogging description and chart below. 2. Make sure and secure latch bolt engagement. Adjust strike if required. 3. Install chassis cover on chassis. 4. Install end cap. Note: For increasing the life of this device, dogging device during high traffic period of the day (Panic device only). Dogging Wrench (Allen Key)
Dogging: Depress push bar, Insert dogging wrench and turn clockwise 35 degrees. Depress push bar
Depress push bar
The push bar will remain depressed and the latch will remain retracted P:\INSTALLATION INST\Mechanical Hardware\INST-S6100.vsd
Rev -
12/10
Release Dogging: Depress push bar, Insert dogging wrench and turn counter-clockwise 35 degrees.
Page 4
The push bar will return to up position and the latch will project to lock the door.
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com E-mail:
[email protected] S6200 SERIES PANIC/FIRE EXIT
SURFACE MOUNTED VERTICAL ROD DEVICES INSTALLATION INSTRUCTIONS
These instructions are presented in a step by step sequence. Please read it through before installation. Note: The dimensions are shown in inches. See attached page for the Metric Conversion Table for millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Rev -
01/11
Page 1
DESIGNATION OF PARTS Top Strike Fixing Plate Top Strike (Back View)
Mounting Bracket
Top Strike Top Strike (Panic Label) (Fire Label) Top Latch End Cap Bracket Assembly Top Latch Assembly Cover Mechanism Housing
End Cap
Top Rod Dogging Device Fire Exit Hardware is not equipped with this device
Rod Guide
Shaft Connector
Chassis Assy. Push Bar
Chassis Cover
CAUTION: Mounting Bracket Bottom Rod
Rod Guide
Before installing this device, check contents of box for size of device, function, finish color and outside trim to be used.
Bottom Latch Assembly Cover
Bottom Latch Assembly
Bottom Strike (Panic Label)
Bottom Strike (Fire Label) Bottom Strike Base P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Rev -
01/11
Page 2
STEP 1: PREPARE DOOR 1. Mark position of holes on the door per template (see figure 1). 2. Drill all holes marked on the door for the device chassis and top and bottom latch mounting brackets. 3. Mortise hole for outside trim is required. NOTE; Any hole drilled from the outside, first needs a pilot hole drilled from the inside to ensure good alignment.
Mark Backset 2-7/16”
JAMB
2-5/16" Prepare door for your specific device per supplied template.
3-7/32"
INSIDE FACE OF DOOR
Surface of the door must be flush. Clear away any raised jutting to allow the exit device to rest on flat surface of the door.
Mark CL of device
1016mm (40")
CL of top and bottom latches 3-7/32" 1-15/32"
40" to finished floor
1/4”
Standard centerline height of device is 40" above the finished floor.
Figure 1 P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Rev -
01-11
Page 3
STEP 2: INSTALL BRACKETS, DEVICE & TRIM 1. Remove chassis cover from chassis assembly and end cap from end cap bracket. 2. Cut the length if required. For user information; This model device has three different lengths: For use on 3' wide door, device = 33" For use on 3.5' wide door, device = 40" For use on 4' wide door, device = 44" a. The device length is pre-cut for use on 36", 42" or 48" wide doors, no additional cutting is necessary. If narrow door installation is required, cut device at section “A” to door width minus 2" for proper fit. b. Remove device from door, remove end cap and end cap bracket and cut where required. NOTE: Device must be cut flat with all burrs removed for end cap to fit properly. 3. Mount device horizontally via the drilled holes and secure with supplied mounting hardware. Attach device to trim or sexbolt. 4. Check that the trim actuator shaft fully inserts into the device cam (refer to view “B”). 5. Install end cap bracket to device, level device Hinge Stile edge of door and mark then drill the mounting holes. Attach to door with hardware supplied. Attach end cap. 6. Install mounting brackets to top End cap and bottom of door. bracket
*
Chassis
“A”
*
Mark mounting holes thru end cap bracket after device is leveled.
VIEW “B” Insert Trim Actuator Shaft Into Device Cam Mounting Bracket
Figure 2 P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Rev -
01-11
Page 4
STEP 3: INSTALL BOTTOM ROD AND BOTTOM STRIKE 1. Mount the bottom latch assembly into the mounting bracket (see figure 3). 2. Screw the threaded end of the bottom rod onto the bottom latch assembly (see figure 4).
Threaded end of Bottom rod
Figure 3
Figure 4
3. Using screw supplied, attach and tighten the bottom rod to the chassis at the location indicated by the arrow in figure 5. NOTE: If the hole on the bottom shaft connector does not align with the mounting hole in the chassis, adjust the length by turning the rod in or out of the latch assembly. 4. Install bottom strike into finished floor or threshold, and be sure to align center line of bottom latch with the centerline of the bottom strike (see figure 6) CL
1/4”
7/8” 2-3/32”
2-1/4”
5. Depress and release push bar to confirm proper installation. 5-1 Make sure bottom latch can be retracted and flush with the edge of the door when push bar is depressed. 5-2 Check bottom latch bolt has 19/32" (15mm) throw min. when push bar is released.
Figure 5
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Figure 6
Rev -
01-11
Page 5
STEP 4: INSTALL TOP ROD AND TOP STRIKE 1. Mount the top latch assembly into the mounting bracket (see figure 7). 2. Screw the threaded end of the top rod onto the top latch assembly completely (see figure 8).
Threaded end of top rod
Figure 7
Figure 8
3. Measure and cut the length of the top rod. The length of the top rod is measured to the edge of the rod connector (see figure 9) which will be attached to the chassis. 4. Insert the rod connector into the non-threaded end of the top rod and secure in place by tightening the locking screw (see figure 10). 5. With the top rod connector installed, attach the top rod to the chassis at the location indicated by the arrow (see figure 11). Non-threaded end of top rod
Mark cutting line and cut top rod
Edge of rod connector Locking screw
Figure 9
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Rev -
01-11
Page 6
Figure 10
Figure 11
6. Mark and drill mounting holes on the jamb for the top strike per the strike template (see figure 12). Fasten the top strike to the jamb with the screws supplied (see figure 13).
Figure 12
Figure 13 NOTE: Attach third screw last after strike has been properly aligned,
STEP 5: TEST OPERATION 1. Depress the push bar. The top and bottom latches should be held retracted. The bottom latch should also clear the floor and the bottom strike. Door can now be opened. 2. Release push bar, both the top latch bolt and the bottom latch bolt should be fully extended. 3. Check device operation by depressing and releasing push bar several times to assure final installation is correct. 4. Repeat device operation by opening and closing door several times using the outside trim to make sure all installations have no problems. 5. Repeat adjustment procedure if either the top latch bolt is not held retracted, or bottom latch bolt does not clear floor and bottom strike.
STEP 6: INSTALL COVERS 1. Before installing covers, check and secure top and bottom latch bolts engagement. Adjust strikes if necessary. 2. Install the chassis and top & bottom assembly covers and the two rod guides (see figure 14).
Figure 14
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
Rev -
01-11
Page 7
Outside of Door
Door Handing Use this diagram to determine the hand of door.
RHR
LHR Inside of Door
NOTE: To extend the life of this device, it is recommended to activate the dogging feature during high traffic periods of the day.
Dogging Wrench
Dogging:
Release Dogging:
Insert dogging wrench and turn clockwise 15 degrees.
Insert dogging wrench and turn counter-clockwise 15 degrees.
Depress Push Bar
Depress Push Bar
The push bar will remain pressed and the latches will remain retracted.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6200.vsd
The push bar will return to the up position and the latches will extend to lock the door.
Rev -
01-11
Page 8
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com E-mail:
[email protected] S6800 SERIES PANIC/FIRE EXIT
CONCEALED VERTICAL ROD DEVICES INSTALLATION INSTRUCTIONS
These instructions are presented in a step by step sequence. Please read it through before installation. Note: The dimensions of the Template are shown in inches. See attached page for the Metric Conversion Table for millimeters. P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Page 1
DESIGNATION OF PARTS Rod Length Locator
Top Strike Fixing Plate Top Strike (Back View) Top Strike (Fire Label)
Top Strike (Panic Label) End Cap
Latch Mounting Plate
End Cap Bracket Mechanism Housing
Top Latch Assembly Top Rod
Dogging Device Fire Exit Hardware is not equipped with this device
Shaft Connector Push Bar Latch Actuated Shaft Chassis Cover
Before installing this device, check contents of box for size of device, function, finish color and outside trim to be used.
Bottom Rod Bottom Latch Assembly
Bottom Strike (Fire Label)
Bottom Strike (Panic Label)
Bottom Strike Base
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
CAUTION:
Rev -
12/10
Page 2
CL of Device
A. PREPARE DOOR 1. Mark centerline of device by drawing a line across the door.
2-7/16"
Figure 1-1 2. Mark a backset line and 4 thru holes for device chassis shown on the template provided.
Mark backset from edge of door
INSIDE FACE OF DOOR 3. Prepare the door cut-outs by using the template provided.
Drill holes and cut-outs on the Device side ONLY
39
4” -3/
CL of Device The centerline of the device must be 40" above the finished floor. Bottom Door gap MUST be 1/4”.
See Trim Installation Instructions for outside face of door preparation.
4. Cut out the top edge and bottom edge of the door, then weld two 5mm thick mounting plates on both edges for Top and Bottom Latch Assemblies (figure 1-2). 5. Drill holes and use a #10-24 tap on the mounting plates on the top and bottom of door. 2-7/16”
1-9/32"
1-19/32"
Figure 1-2
1-5/32"
7/8" 1-11/16"
23/32"
7/16"
Inside Face of Door
7/8" 7/8" 1-17/32"
1-3/4” 2-1/4”
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Page 3
B. ASSEMBLE RODS AND LATCHES 1. Screw bottom rod into bottom latch assembly (figure 2-1). 2. Assemble top rod: 2-1 Connect short top rod to long top rod using rod connector (figure 2-1). 2-2 Measure and cut the length of the top rod if it is too long.
Bottom rod
Bottom latch assembly
Figure 2-1
Figure 2-2
2-3 Insert shaft connector into the non-threaded end of the top rod and tighten screw to fix in place (figure 2-3). 3. Screw top rod assembly into top latch assembly (figure 2-4). Top latch assembly Non-threaded End of top rod
Shaft connector Top rod assembly
Non-threaded End of top rod
Figure 2-4
Figure 2-3 P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Page 4
C. MOUNT LATCH ASSEMBLIES 1. Attach latch mounting brackets to top and bottom latch assemblies 2. Insert top latch assembly into top of the door and fasten to the mounting plates with the screws provided (figure 3-1). 3. Insert bottom latch assembly into bottom of the door and fasten to the mounting plates with the screws provided (figure 3-2). Latch mounting bracket m tto o B
Top latch assembly
d of
r oo
Mounting plate
Mounting plate
Bottom latch assembly or do f po To
Latch mounting bracket
Figure 3-2
Figure 3-1 D. ADJUST VERTICAL RODS
1. Place the rod length locator through the cut-outs on the inside face of the door. Hook a shaft connector with the small stud on the locator. When the shaft connector is raised to as level as possible, the holes C or D in the locator should align with the cut-outs A or B (figure 4-1). 2. If the C or D holes in the locator do not align with their respective cut-out, then the vertical rod length is incorrect and must be adjusted. Rod Length Locator Stud for hooking
Bottom latch assembly Hole D
Top shaft
Hole C
CL of Device Cut-Out B Cut-Out A
Top latch assembly P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Figure 4-1 Rev -
12/10
Page 5
Bottom shaft CL of Device
3. Adjustment procedure: Adjust the length of the two vertical rods by hand through the cut-outs (figure 4-2). Shorten or lengthen the rods by turning into or out of the latch assemblies (figure 4-3) until the holes of the shaft connectors are in the proper position as determined by the latch length locator (pg. 5, figure 4-1).
Figure 4-2
Figure 4-3
E. INSTALL LATCH ACTUATOR SHAFTS 1. Attach one Latch Actuated Shaft to the top and bottom shaft connectors (figure 5) with screws supplied. 2. Make sure both top and bottom latch actuated shafts are parallel.
F. INSTALL DEVICE AND TRIM (if applicable) Latch Actuated Shaft
1. Remove device chassis cover from the chassis assembly and the end cap from the end cap bracket. 2. Position the device on the door and insert latch actuated shafts into the slots marked “X” and “Y” (figure 6-1). Fasten in place with screws supplied.
Figure 5 Y
X
Figure 6-1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Page 6
3. Cut the length if required: a. The device length is pre-cut for use on 36", 42" or 48" wide doors, no additional cutting is necessary. If narrow door installation is required, cut device at section “A” to door width minus 2" for proper fit. b. Remove device from door, remove end cap and end cap bracket and cut where required. NOTE: Device must be cut flat with all burrs removed for end cap to fit properly. 4. Mount device horizontally via the drilled holes and secure with supplied mounting hardware. Attach device to trim or sexbolt (if applicable). 5. Install end cap bracket to device and attach to door with hardware supplied. Attach end cap.
A
Figure 6-2
G. TEST OPERATION AND HANG DOOR. 1. Depress push bar. Top latch bolt should be retracted as shown (figure 7-1) and bottom latch clears floor and bottom strike (figure 7-2). BOTTOM LATCH BOLT (Clears floor and strike).
Figure 7-2
Figure 7-1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Page 7
2. Release push bar, Make sure both top and bottom latch bolts are FULLY extended 3. Check top latch bolt for deadlocking function. Deadlock Depress the deadlock plate by hand. Top Latch Plate When the deadlock plate is depressed, Bolt the latch bolts should be locked in the Figure 7-3 extended position and unable to be pressed down (figure 7-3). 4. Check device operation by depressing and releasing push bar several times to assure correct final installation. 5. Hang door (with device installed) and repeat operation check with outside lever. 6. redo rod length adjustment if either top latch bolt is not held retracted or if the bottom latch bolt does not clear the floor and bottom strike. 2.598"
H. INSTALL TOP STRIKE
1.969"
1. Prepare frame: a. Cut out a square on the frame for the top strike (figure 8-1). b. Weld two 3mm thick mounting plates on the frame (figure 8-2). c. Drill holes and tap #10-24 threads on the mounting plates.
1.417" 1.339" 2.441"
1.496" .472" 1.831" .985" .079"
Figure 8-1
1.339"
.748" 1.732" 3.150" 4.134"
.236"
Figure 8-2
2. Install the top strike on the mounting plates (figure 8-3) and secure with supplied screws (figure 8-4).
Figure 8-3
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Figure 8-4
Page 8
I. INSTALL BOTTOM STRIKE 1. Bore the hole into the finished floor or threshold (figure 9-1). 2. Install bottom strike into the hole (figure 9-2). CL of Bottom Latch
2.441"
1.126"
DOOR (Top View)
CL of Bottom Latch
.748" DIAMETER 1.850"
1/4”
1/4”
NOTE: For flat thresholds the clearance must be provided in sill to accommodate full 9/16" (15mm) throw of latch bolt.
Flat threshold application (Panic device ONLY)
Strike application
J. INSTALL COVERS 1. Test push bar operation before installing covers; a. No Trim: Latch bolts are retracted by the push bar inside. b. With Trim: Latch bolts are retracted by the push bar inside, key or lever/knob outside. c. Dogging: See dogging description and chart page 10. 2. Check latch bolt engagement, adjust strikes if required. 3. Install chassis cover over chassis assembly. 4. Install end cap.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
Rev -
12/10
Page 9
Outside of Door
Door Handing Use this diagram to determine the hand of door.
RHR
LHR Inside of Door
NOTE: To extend the life of this device, it is recommended to activate the dogging feature during high traffic periods of the day.
Dogging Wrench
Dogging:
Release Dogging:
Insert dogging wrench and turn clockwise 15 degrees.
Insert dogging wrench and turn counter-clockwise 15 degrees.
Depress Push Bar
Depress Push Bar
The push bar will remain pressed and the latches will remain retracted.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6800.vsd
The push bar will return to the up position and the latches will extend to lock the door.
Rev -
12/10
Page 10
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com • E-mail:
[email protected] INSTALLATION INSTRUCTIONS S6000-ATS ANTI-TAMPER SWITCH KIT
Insert Anti-Tamper Switch where shown.
Remove Device Cover and End Cap.
END CAP BRACKET
DEVICE COVER END CAP
Insert the S6000-ATS Assy. into the device. Slide the End Cap over the End Cap Bracket. Position the S6000-ATS Assy so the switch arm makes contact and is activated by the inside surface of the End Cap. Hold the S6000-ATS Assy. in place as you slide out the End Cap. Tighten the set screws on the S6000-ATS to lock it in place. Switch Arm
Once S6000-ATS Switch Assembly is properly located, wire the switch and re-install the Device Cover and End Cap.
END CAP
Electrical Specifications: WHT = COM YEL = N/O ORG = N/C 5AMPS @ 250V Resistive
P:\INSTALLATION INST\SWITCH KITS\INST-S6000-ATS.vsd
REV -
04-12
Page 1
Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email
[email protected]