Riverside Furniture
Riverside FURNITURE
Terra Vista Bedroom
Panel Headboard & Bench Footboard
Assembly Instructions
email: [email protected]
1 pc.
8 pcs.
98870 -- 4/6-5/0 panel Headboard 98871 -- 5/0 Uph. Bench Footboard & Slats. 98872 -- 5/0-6/6 Panel Bed Rails (for 5/0 Bed)
2 pcs.
Page 1 of 5
Made in Viet Nam
Riverside FURNITURE
email: [email protected]
Terra Vista Bedroom
Panel Headboard & Bench Footboard
Assembly Instructions
ASSEMBLY STEPS : 1. Place the Headboard Panel (H-A) face down on a clean and soft surface. 2. Install the six All-Thread Bolts (H-H) into the threaded metal inserts and the Wooden Dowels (H-L) into the holes on the edges of the Headboard panel. 3. Attach the Left and Right Headboard Posts ( H-B) to the edge of the Headboard Panel, using the Washers (H-I), Spring Washers (H-E) and Hex Nut (H-J) onto the All-thread Bolt (H-H). (see detail A). Do not fully tighten until after next step. 4. Attach the Headboard Stretcher (H-C) to the back of the Headboard Posts using the Bolts (H-D) and Spring Washers (H-E), and Flat Washers (H-F). Tighten all Allen Bolts using the Allen Wrench ( H-G) and Hex Nuts with the Open Wrench (H-K). (see detail B). 5. Install the eight All-Thread Bolts (R-B) into the threaded metal inserts mounted on the Headboard and Footboard posts. 6. Gently lean the Headboard against the wall where the completed Bed will be located in the room. 7. Position one end of one Bed Rail (R-A) onto the All-Thread Bolts and fasten with the Washers (R-C & R-D) and Hex Nuts (R-E). Only partially tighten the Hex Nuts until the Footboard has been connected. Repeat for other Bed Rail. 8. Position and connect the Footboard to the other end of the Bed Rails as in previous Step. 9. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-F) tighten all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail C) 10. Attach the Support Leg (F-C) to the Wood Slat (F-B). (See Detail: D) 11. Attach the Wood Slats to the Bed Rails using the Wood Screws (F-D) and your Phillips Screwdriver. The levelers located at the bottom of the Support Legs can be adjusted if necessary. (See Detail E)
Page 2 of 5
Made in Viet Nam
Riverside FURNITURE
Terra Vista Bedroom
Panel Headboard & Panel Footboard
Assembly Instructions
email: [email protected]
1 pc.
8 pcs.
98870 -- 4/6-5/0 Panel Headboard 98875 -- 5/0 Panel Footboard & Slats. 98872 -- 5/0-6/6 Panel Bed Rails (for 5/0 Bed)
2 pcs.
Page 3 of 5
Made in Viet Nam
Riverside FURNITURE
email: [email protected]
Terra Vista Bedroom
Panel Headboard & Panel Footboard
Assembly Instructions
ASSEMBLY STEPS : 1. Place the Headboard Panel (H-A) face down on a clean and soft surface. 2. Install the six All-Thread Bolts (H-H) into the threaded metal inserts and the Wooden Dowels (H-L) into the holes on the edges of the Headboard panel. 3. Attach the Left and Right Headboard Posts (H-B) to the edge of the Headboard Panel, using the Washers (H-I), Spring Washers (H-E) and Hex Nut (H-J) onto the All-thread Bolt (H-H). (see detail A). Do not fully tighten until after next step. 4. Attach the Headboard Stretcher (H-C) to the back of the Headboard Posts using the Bolts (H-D) and Spring Washers (H-E), and Flat Washers (H-F). Tighten all Allen Bolts using the Allen Wrench (H-G) and Hex Nuts with the Open Wrench (H-K). (see detail B). 5. Install the eight All-Thread Bolts (R-B) into the threaded metal inserts mounted on the Headboard and Footboard posts. 6. Gently lean the Headboard against the wall where the completed Bed will be located in the room. 7. Position one end of one Bed Rail (R-A) onto the All-Thread Bolts and fasten with the Washers (R-C & R-D) and Hex Nuts (R-E). Only partially tighten the Hex Nuts until the Footboard has been connected. Repeat for other Bed Rail. 8. Position and connect the Footboard to the other end of the Bed Rails as in previous Step. 9. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-F) tighten all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail C) 10. Attach the Support Leg (F-C) to the Wood Slat (F-B). (See Detail: D) 11. Attach the Wood Slats to the Bed Rails using the Wood Screws (F-D) and your Phillips Screwdriver. The levelers located at the bottom of the Support Legs can be adjusted if necessary. (See Detail E)
Page 4 of 5
Made in Viet Nam
Riverside email: [email protected]
Terra Vista 98870 Queen Panel Bed Headboard
Page 5 of 5
98870 -- 4/6-5/0 Panel Headboard 98872 -- 5/0-6/6 Panel Bed Rails and with either footboard below
Terra Vista Bedroom
Panel Headboard & Bench Footboard
Assembly Instructions
email: [email protected]
1 pc.
8 pcs.
98870 -- 4/6-5/0 panel Headboard 98871 -- 5/0 Uph. Bench Footboard & Slats. 98872 -- 5/0-6/6 Panel Bed Rails (for 5/0 Bed)
2 pcs.
Page 1 of 5
Made in Viet Nam
Riverside FURNITURE
email: [email protected]
Terra Vista Bedroom
Panel Headboard & Bench Footboard
Assembly Instructions
ASSEMBLY STEPS : 1. Place the Headboard Panel (H-A) face down on a clean and soft surface. 2. Install the six All-Thread Bolts (H-H) into the threaded metal inserts and the Wooden Dowels (H-L) into the holes on the edges of the Headboard panel. 3. Attach the Left and Right Headboard Posts ( H-B) to the edge of the Headboard Panel, using the Washers (H-I), Spring Washers (H-E) and Hex Nut (H-J) onto the All-thread Bolt (H-H). (see detail A). Do not fully tighten until after next step. 4. Attach the Headboard Stretcher (H-C) to the back of the Headboard Posts using the Bolts (H-D) and Spring Washers (H-E), and Flat Washers (H-F). Tighten all Allen Bolts using the Allen Wrench ( H-G) and Hex Nuts with the Open Wrench (H-K). (see detail B). 5. Install the eight All-Thread Bolts (R-B) into the threaded metal inserts mounted on the Headboard and Footboard posts. 6. Gently lean the Headboard against the wall where the completed Bed will be located in the room. 7. Position one end of one Bed Rail (R-A) onto the All-Thread Bolts and fasten with the Washers (R-C & R-D) and Hex Nuts (R-E). Only partially tighten the Hex Nuts until the Footboard has been connected. Repeat for other Bed Rail. 8. Position and connect the Footboard to the other end of the Bed Rails as in previous Step. 9. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-F) tighten all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail C) 10. Attach the Support Leg (F-C) to the Wood Slat (F-B). (See Detail: D) 11. Attach the Wood Slats to the Bed Rails using the Wood Screws (F-D) and your Phillips Screwdriver. The levelers located at the bottom of the Support Legs can be adjusted if necessary. (See Detail E)
Page 2 of 5
Made in Viet Nam
Riverside FURNITURE
Terra Vista Bedroom
Panel Headboard & Panel Footboard
Assembly Instructions
email: [email protected]
1 pc.
8 pcs.
98870 -- 4/6-5/0 Panel Headboard 98875 -- 5/0 Panel Footboard & Slats. 98872 -- 5/0-6/6 Panel Bed Rails (for 5/0 Bed)
2 pcs.
Page 3 of 5
Made in Viet Nam
Riverside FURNITURE
email: [email protected]
Terra Vista Bedroom
Panel Headboard & Panel Footboard
Assembly Instructions
ASSEMBLY STEPS : 1. Place the Headboard Panel (H-A) face down on a clean and soft surface. 2. Install the six All-Thread Bolts (H-H) into the threaded metal inserts and the Wooden Dowels (H-L) into the holes on the edges of the Headboard panel. 3. Attach the Left and Right Headboard Posts (H-B) to the edge of the Headboard Panel, using the Washers (H-I), Spring Washers (H-E) and Hex Nut (H-J) onto the All-thread Bolt (H-H). (see detail A). Do not fully tighten until after next step. 4. Attach the Headboard Stretcher (H-C) to the back of the Headboard Posts using the Bolts (H-D) and Spring Washers (H-E), and Flat Washers (H-F). Tighten all Allen Bolts using the Allen Wrench (H-G) and Hex Nuts with the Open Wrench (H-K). (see detail B). 5. Install the eight All-Thread Bolts (R-B) into the threaded metal inserts mounted on the Headboard and Footboard posts. 6. Gently lean the Headboard against the wall where the completed Bed will be located in the room. 7. Position one end of one Bed Rail (R-A) onto the All-Thread Bolts and fasten with the Washers (R-C & R-D) and Hex Nuts (R-E). Only partially tighten the Hex Nuts until the Footboard has been connected. Repeat for other Bed Rail. 8. Position and connect the Footboard to the other end of the Bed Rails as in previous Step. 9. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-F) tighten all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail C) 10. Attach the Support Leg (F-C) to the Wood Slat (F-B). (See Detail: D) 11. Attach the Wood Slats to the Bed Rails using the Wood Screws (F-D) and your Phillips Screwdriver. The levelers located at the bottom of the Support Legs can be adjusted if necessary. (See Detail E)
Page 4 of 5
Made in Viet Nam
Riverside email: [email protected]
Terra Vista 98870 Queen Panel Bed Headboard
Page 5 of 5
98870 -- 4/6-5/0 Panel Headboard 98872 -- 5/0-6/6 Panel Bed Rails and with either footboard below
