Rugged Fender Flares Nissan Titan (04-15) FIT
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
Please read instructions entirely before installing this product. Hardware Included ALCOHOL TOWELETTE CLIP .9MM EXTRUSION U SHAPE CLIP
QTY 4 2 26ft 8
FUEL DOOR CLIP M4 SCREW ABRASIVE RESISTANT TAPE
1 1 1
Bolt Kit Included ALLEN KEY BOLT NUT
QTY 42 42
Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle. NOTE: Before fitting Fender Flares remove any moldings, strips or existing flares from the wheel arch. If there is a body side molding, mark where the molding is to be cut, alternatively the Fender Flare can be cut to go around the molding. Be sure to allow enough room for the extrusion.
*PRIOR TO ANY PAINTING & INSTALLATION, PRODUCT SHOULD BE THOROUGHLY INSPECTED FOR ALL COMPONENTS LISTED ABOVE. PRODUCT SHOULD ALSO BE TEST FITTED PRIOR TO ANY PAINTING & INSTALLATION. PLEASE CONTACT ROUGH COUNTRY IF YOU HAVE ANY FITMENT QUESTIONS AND OR MISSING COMPONENTS. *For Rugged look flares begin installation at STEP 2. PAINTING INSTRUCTIONS – If Fender Flares are being painted; do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do not use lacquer thinner or any solvent based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with a tack rag just prior to painting. Most automotive paints can be applied directly to the Fender Flares, however some may require a primer (check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that is suitable for rigid plastics PMMA (Acrylic). If using a paint system that requires baking, do not expose the product to temperatures above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry.
STEP 1: Attach 10 bolts to each Fender Flare using a
STEP 2: Attach the included rubber seal to the Fender
3/16” Allen key and a 10mm wrench/socket. (wrench/socket and Allen key not supplied). Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.
Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Attach rubber seal along all areas the Fender Flare will make contact with the vehicle body.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
STEP 3: Pulling at right angles to the extrusion,
FIT-FF754
STEP 4: Trim any unnecesary extrusion and discard.
remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.
STEP 5: Clean the body areas where the Fender
STEP 6: Remove the five OEM factory screws from the wheel
Flares will make contact..
arch molding. For vehicles with factory mud flaps, remove the two existing OEM screws as shown. Remove mud flap from the vehicle. Retain screws.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
STEP 7: Place Fender Flare on vehicle and attach four of
STEP 8: Locate top provided clip in the center top slot in
the existing factory screws previously removed as shown. Do not fully tighten at this stage.
the Fender Flare. Using the remaining factory screw, secure the clip to the inside of wheel arch. Ensure the barb arm in clip is secure in the Fender Flare slot.
STEP 9: If necessary, make minor adjustments to the Fender Flare's position to achieve the best fit for your vehicle. Once satisfied, tighten all screws currently installed.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
REAR FENDER FLARE INSTALLATION
STEP 10: Attach 11 bolts to the Fender Flares using a
STEP 11: Attach the included rubber seal to the
3/16” Allen key and a 10mm wrench/socket. (wrench/socket and Allen key not supplied). Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.
Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Attach rubber seal along all areas the Fender Flare will make contact with the vehicle body. Trim any excess rubber seal.
STEP 12: Pulling at right angles to the extrusion,
STEP 13: Trim any unnecesary extrusion and discard.
remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
STEP 14: For vehicles with factory mud flaps, remove the
STEP 15: For left hand side of vehicle with factory mud
three existing OEM screws as shown. Remove mud flap from the vehicle. For vehicles with out factory mud flaps remove the existing three OEM screws in the wheel arch. Retain screws.
flaps, remove the two existing OEM screws as shown. Remove mud flap from the vehicle. For vehicles with out factory mud flaps remove the existing two OEM screws in the wheel arch. Retain screws.
STEP 16: Remove approximately 2” of tape liner from extrusion so it may be pulled off the flare once fitted. Fold the liner to the outside of fender flare. Place Fender Flare on vehicle and attach three of the existing factory screws previously removed on the right hand side part and two on the left hand side as shown. Do not fully tighten at this stage.
STEP 17: To secure the Fender Flare to the body, apply upward tension on Fender Flare to the vehicle fender when installing the ‘U’ shape metal clips. Slide the clips over the Fender Flare and the inner wheel arch lip in the four locations shown. Position the clip so that the barb in the clip locates in the slot of the Fender Flare. Once fender falres are fitted, pull exposed liner from extrusion at right angles to flares. Using a soft cloth apply pressure around the edge of fender flares to achieve proper adhesion of the extrusion tape to the vehicle.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
STEP 18: Open fuel cap door, attach the piece of
STEP 19: Attach the fuel door flare to the fuel door using
abrasive resistant tape provided to the noted area on the fuel door. Fold the tape around the edge of the fuel door so half of the tape is on either side. Slide the provided clip over this same area, ensuring that the clip does not come into contact with the painted surface of the fuel door.
the M4 screw and fiber washer provided in the kit. Ensure the fuel door flare is located vertically even on the fuel door, to ensure an even gap to each side of the previously fitted main flare. Pull exposed liner from extrusion at right angles to fuel door flare. Using a soft cloth apply pressure around the edge of fuel door flare to achieve proper adhesion of the extrusion tape to the vehicle.
STEP 20: Double check the front and rear Fender Flares to make sure all bolts are tight and clips are securely fastened. Your installation is now complete. Do not use abrasive cleaners.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
FIT-FF754
Please read instructions entirely before installing this product. Hardware Included ALCOHOL TOWELETTE CLIP .9MM EXTRUSION U SHAPE CLIP
QTY 4 2 26ft 8
FUEL DOOR CLIP M4 SCREW ABRASIVE RESISTANT TAPE
1 1 1
Bolt Kit Included ALLEN KEY BOLT NUT
QTY 42 42
Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle. NOTE: Before fitting Fender Flares remove any moldings, strips or existing flares from the wheel arch. If there is a body side molding, mark where the molding is to be cut, alternatively the Fender Flare can be cut to go around the molding. Be sure to allow enough room for the extrusion.
*PRIOR TO ANY PAINTING & INSTALLATION, PRODUCT SHOULD BE THOROUGHLY INSPECTED FOR ALL COMPONENTS LISTED ABOVE. PRODUCT SHOULD ALSO BE TEST FITTED PRIOR TO ANY PAINTING & INSTALLATION. PLEASE CONTACT ROUGH COUNTRY IF YOU HAVE ANY FITMENT QUESTIONS AND OR MISSING COMPONENTS. *For Rugged look flares begin installation at STEP 2. PAINTING INSTRUCTIONS – If Fender Flares are being painted; do not install edge extrusion until painting is complete. Prior to painting, clean all surfaces to be painted using clean water and a mild detergent, do not use lacquer thinner or any solvent based products. Wipe completely dry. Best results will be achieved by wiping the areas to be painted with a tack rag just prior to painting. Most automotive paints can be applied directly to the Fender Flares, however some may require a primer (check paint manufacturer specifications). Good adhesion will be achieved without sanding. Select a paint (and primer if necessary) that is suitable for rigid plastics PMMA (Acrylic). If using a paint system that requires baking, do not expose the product to temperatures above 70°C (158°F). Do not fit the extrusion or any of the hardware to the Fender Flares until the paint is completely dry.
STEP 1: Attach 10 bolts to each Fender Flare using a
STEP 2: Attach the included rubber seal to the Fender
3/16” Allen key and a 10mm wrench/socket. (wrench/socket and Allen key not supplied). Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.
Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Attach rubber seal along all areas the Fender Flare will make contact with the vehicle body.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
STEP 3: Pulling at right angles to the extrusion,
FIT-FF754
STEP 4: Trim any unnecesary extrusion and discard.
remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.
STEP 5: Clean the body areas where the Fender
STEP 6: Remove the five OEM factory screws from the wheel
Flares will make contact..
arch molding. For vehicles with factory mud flaps, remove the two existing OEM screws as shown. Remove mud flap from the vehicle. Retain screws.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
STEP 7: Place Fender Flare on vehicle and attach four of
STEP 8: Locate top provided clip in the center top slot in
the existing factory screws previously removed as shown. Do not fully tighten at this stage.
the Fender Flare. Using the remaining factory screw, secure the clip to the inside of wheel arch. Ensure the barb arm in clip is secure in the Fender Flare slot.
STEP 9: If necessary, make minor adjustments to the Fender Flare's position to achieve the best fit for your vehicle. Once satisfied, tighten all screws currently installed.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
REAR FENDER FLARE INSTALLATION
STEP 10: Attach 11 bolts to the Fender Flares using a
STEP 11: Attach the included rubber seal to the
3/16” Allen key and a 10mm wrench/socket. (wrench/socket and Allen key not supplied). Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.
Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Attach rubber seal along all areas the Fender Flare will make contact with the vehicle body. Trim any excess rubber seal.
STEP 12: Pulling at right angles to the extrusion,
STEP 13: Trim any unnecesary extrusion and discard.
remove the liner from the extrusion in small portions and apply thumb pressure to ensure that it adheres to the Fender Flares.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
STEP 14: For vehicles with factory mud flaps, remove the
STEP 15: For left hand side of vehicle with factory mud
three existing OEM screws as shown. Remove mud flap from the vehicle. For vehicles with out factory mud flaps remove the existing three OEM screws in the wheel arch. Retain screws.
flaps, remove the two existing OEM screws as shown. Remove mud flap from the vehicle. For vehicles with out factory mud flaps remove the existing two OEM screws in the wheel arch. Retain screws.
STEP 16: Remove approximately 2” of tape liner from extrusion so it may be pulled off the flare once fitted. Fold the liner to the outside of fender flare. Place Fender Flare on vehicle and attach three of the existing factory screws previously removed on the right hand side part and two on the left hand side as shown. Do not fully tighten at this stage.
STEP 17: To secure the Fender Flare to the body, apply upward tension on Fender Flare to the vehicle fender when installing the ‘U’ shape metal clips. Slide the clips over the Fender Flare and the inner wheel arch lip in the four locations shown. Position the clip so that the barb in the clip locates in the slot of the Fender Flare. Once fender falres are fitted, pull exposed liner from extrusion at right angles to flares. Using a soft cloth apply pressure around the edge of fender flares to achieve proper adhesion of the extrusion tape to the vehicle.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
Bolt-On/Rugged Fender Flares Nissan Titan (04-15)
FIT-FF754
STEP 18: Open fuel cap door, attach the piece of
STEP 19: Attach the fuel door flare to the fuel door using
abrasive resistant tape provided to the noted area on the fuel door. Fold the tape around the edge of the fuel door so half of the tape is on either side. Slide the provided clip over this same area, ensuring that the clip does not come into contact with the painted surface of the fuel door.
the M4 screw and fiber washer provided in the kit. Ensure the fuel door flare is located vertically even on the fuel door, to ensure an even gap to each side of the previously fitted main flare. Pull exposed liner from extrusion at right angles to fuel door flare. Using a soft cloth apply pressure around the edge of fuel door flare to achieve proper adhesion of the extrusion tape to the vehicle.
STEP 20: Double check the front and rear Fender Flares to make sure all bolts are tight and clips are securely fastened. Your installation is now complete. Do not use abrasive cleaners.
Rough Country Suspension 1-800-222-7023 www.roughcountry.com
