samples/XD Instructions
Terms and Conditions
...CONTINUED
8.
open your dominant eye and close your nondominant one. Maintain your mount even if the target appears shifted. If you can see a portion of the barrel by the outer edge of the blade, take the next widest blade from the same stack and repeat the test. Keep testing blades until you no longer see the barrel but you can still see the shifted target. ⍟Do not try to see the barrel or the target above the blade.
Once you found the correct blade, tighten the blade screw (A) until the blade is fixed.
Outer Edge
⍟ The assembly and mounting of the device are
best done with the shotgun held horizontally and upside down.
75mm 2.95in
65mm 2.55in
55mm 2.16in
The shotgun must be unloaded while you install or adjust the device!
You (the “Buyer”) purchased the XD Solution product (the “Product”) sold by Nut Media, LLC (the “Company”).
The Product should perform as advertised if used in the manner described in these package instructions or on the website. The Company does not guarantee that the Product will perform its functions if used in any other way. The XD Solution website and these instructions offer guidelines on proper usage and assembly, however the Buyer is responsible for the correct implementation of those guidelines. The Buyer does not hold the Company, its members, or its affiliates responsible or liable for any loss, damage, injury or death caused directly or indirectly to the Buyer in connection with the use of the Product. This also applies to users of the Product other than the Buyer.
IMPORTANT: For safety reasons, the firearm MUST be unloaded at all time while the Product is being installed on it or adjusted.
A
Holder
S
Slit
B C1 C2
Take the blade holder and insert it into the large hole of the base. Make sure the holder is fully inserted and screw A aligns with screw S. Tighten screw S until the holder is fixed.
2. Remove screw B completely, then fully insert the slit of the base onto the lowest part of the trigger guard. ⍟Slide the device forward as much as possible, but make sure the holder is vertical.
Base
3.
Tighten screws C1, and C2 until the base is fixed.
4.
Reinsert screw B and tighten it but make sure it does not come out on the other side.
5.
Follow the instructions for selecting the correct blade.
Sold by Nut Media, LLC Contact [email protected] Designed by Bill V. Erdoss
Selecting the correct blade 1.
Assembly and Mounting 1.
Instructions
2.
Blade Screw (A)
Out of the three stacks of blades, take the shortest and narrowest blade. ⍟All the blades from one stack have the same height.
Loosen the blade screw (A). Insert the blade so that the small cut-out fits around the screw. Make sure the blade is vertical.
3.
Pick an object in the distance (15-20 yards/m) to use as a target.
4.
Mount the shotgun and look at the target with both eyes open. Do not try to see the target above the blade. Do you see a double image of the barrel? If yes, go to the next tallest stack of blades, take the narrowest blade, and repeat this step. If you do not see a double image, continue to step 5.
5.
With the shotgun mounted, close your dominant eye and aim at the target. Make sure the shotgun is leveled.
6.
Holding the shotgun in the position of step 5, CONTINUED —>
...CONTINUED
8.
open your dominant eye and close your nondominant one. Maintain your mount even if the target appears shifted. If you can see a portion of the barrel by the outer edge of the blade, take the next widest blade from the same stack and repeat the test. Keep testing blades until you no longer see the barrel but you can still see the shifted target. ⍟Do not try to see the barrel or the target above the blade.
Once you found the correct blade, tighten the blade screw (A) until the blade is fixed.
Outer Edge
⍟ The assembly and mounting of the device are
best done with the shotgun held horizontally and upside down.
75mm 2.95in
65mm 2.55in
55mm 2.16in
The shotgun must be unloaded while you install or adjust the device!
You (the “Buyer”) purchased the XD Solution product (the “Product”) sold by Nut Media, LLC (the “Company”).
The Product should perform as advertised if used in the manner described in these package instructions or on the website. The Company does not guarantee that the Product will perform its functions if used in any other way. The XD Solution website and these instructions offer guidelines on proper usage and assembly, however the Buyer is responsible for the correct implementation of those guidelines. The Buyer does not hold the Company, its members, or its affiliates responsible or liable for any loss, damage, injury or death caused directly or indirectly to the Buyer in connection with the use of the Product. This also applies to users of the Product other than the Buyer.
IMPORTANT: For safety reasons, the firearm MUST be unloaded at all time while the Product is being installed on it or adjusted.
A
Holder
S
Slit
B C1 C2
Take the blade holder and insert it into the large hole of the base. Make sure the holder is fully inserted and screw A aligns with screw S. Tighten screw S until the holder is fixed.
2. Remove screw B completely, then fully insert the slit of the base onto the lowest part of the trigger guard. ⍟Slide the device forward as much as possible, but make sure the holder is vertical.
Base
3.
Tighten screws C1, and C2 until the base is fixed.
4.
Reinsert screw B and tighten it but make sure it does not come out on the other side.
5.
Follow the instructions for selecting the correct blade.
Sold by Nut Media, LLC Contact [email protected] Designed by Bill V. Erdoss
Selecting the correct blade 1.
Assembly and Mounting 1.
Instructions
2.
Blade Screw (A)
Out of the three stacks of blades, take the shortest and narrowest blade. ⍟All the blades from one stack have the same height.
Loosen the blade screw (A). Insert the blade so that the small cut-out fits around the screw. Make sure the blade is vertical.
3.
Pick an object in the distance (15-20 yards/m) to use as a target.
4.
Mount the shotgun and look at the target with both eyes open. Do not try to see the target above the blade. Do you see a double image of the barrel? If yes, go to the next tallest stack of blades, take the narrowest blade, and repeat this step. If you do not see a double image, continue to step 5.
5.
With the shotgun mounted, close your dominant eye and aim at the target. Make sure the shotgun is leveled.
6.
Holding the shotgun in the position of step 5, CONTINUED —>
