Sanyo VPC-X1200 shutter assembly replacement
Sanyo VPC-X1200 shutter assembly replacement
Sanyo VPC-X1200 shutter assembly replacement Written By: Anthony Giardina
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 9
Sanyo VPC-X1200 shutter assembly replacement
INTRODUCTION This guide helps you to remove and replace the lens unit
TOOLS: Phillips #00 Screwdriver (1) Spudger (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 1 — Back Case
Remove the five case screws with a Phillips #00 Screwdriver.
Five 3.5mm Phillips Screws
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Gently lift up the back cover and set aside.
Page 3 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 3 — LCD Screen
Gently lift up on the left side of the LCD and slowly pull it to the left side of the camera but do not remove entirely, there is a ribbon connector.
Be careful not to rip out the ribbon connector.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 4
To clear the ribbon connection underneath the screen, lift up the black ribbon gate with the spudger.
Gently lift ribbon out of the gate and set screen aside.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 5 — Button Plate
There are five screws of three different sizes which need removal.
One 4.5mm screw
Four 3.5mm screws, one on the button side
One 5.5mm screws
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 6
Slowly lift metal tray to the right.
Be careful not to bend the screw tabs or rip out the ribbon cable.
Remove ribbon cable by using the spudger to lift up the black ribbon gate to release the ribbon
Step 7 — Lens Unit
Disconnect the two ribbon cables from the lens unit by using the spudger to lift the ribbon gates.
One gate is black and another is white.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 8
Remove the three silver screws.
Three 5.5mm screws
Step 9
Lift the lens unit free of the camera. A spudger can be used to separate the lens unit if necessary.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 9
Sanyo VPC-X1200 shutter assembly replacement This document was last generated on 2017-06-18 01:25:20 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 9
Sanyo VPC-X1200 shutter assembly replacement Written By: Anthony Giardina
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 9
Sanyo VPC-X1200 shutter assembly replacement
INTRODUCTION This guide helps you to remove and replace the lens unit
TOOLS: Phillips #00 Screwdriver (1) Spudger (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 1 — Back Case
Remove the five case screws with a Phillips #00 Screwdriver.
Five 3.5mm Phillips Screws
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Gently lift up the back cover and set aside.
Page 3 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 3 — LCD Screen
Gently lift up on the left side of the LCD and slowly pull it to the left side of the camera but do not remove entirely, there is a ribbon connector.
Be careful not to rip out the ribbon connector.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 4
To clear the ribbon connection underneath the screen, lift up the black ribbon gate with the spudger.
Gently lift ribbon out of the gate and set screen aside.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 5 — Button Plate
There are five screws of three different sizes which need removal.
One 4.5mm screw
Four 3.5mm screws, one on the button side
One 5.5mm screws
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 6
Slowly lift metal tray to the right.
Be careful not to bend the screw tabs or rip out the ribbon cable.
Remove ribbon cable by using the spudger to lift up the black ribbon gate to release the ribbon
Step 7 — Lens Unit
Disconnect the two ribbon cables from the lens unit by using the spudger to lift the ribbon gates.
One gate is black and another is white.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 9
Sanyo VPC-X1200 shutter assembly replacement
Step 8
Remove the three silver screws.
Three 5.5mm screws
Step 9
Lift the lens unit free of the camera. A spudger can be used to separate the lens unit if necessary.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 9
Sanyo VPC-X1200 shutter assembly replacement This document was last generated on 2017-06-18 01:25:20 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 9
