Savant Wireless Thermostat (SST-W100) Quick Reference Guide
009-0793-02 SST-W100-00
Savant Wireless Thermostat (SST-W100) Quick Reference Guide
The Savant Wireless Thermostat (SST-W100) is a Wi-Fi enabled wireless digital thermostat designed to control Heating, Ventilation and Air Conditioning (HVAC) systems which communicate wirelessly over Wi-Fi to a Savant System. The SST-W100 is designed to integrate seamlessly into a Savant controlled environment.
Holes for mounting on wall screws
Box Contents (1) SST-W100 (1) Installation Kit (xxx) (1) Quick Reference Guide (this document)
Optional Components One of the 16 screw-down connectors used for wiring to climate control devices
SST-TEMP1 - Remote Temperature Sensor
Specifications Environmental Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-condensing)
Rear View of SST-W100
Height
3.96 in/10.06 cm
Wiring
Width
5.775 in/14.67 cm
Depth
.58 in/1.47 cm
Weight
0.5 lb/.23 kg
Dimensions and Weight Screw-down connectors on the inside of the back cover of the SST-W100 are used for wiring connections to various climate control devices. Use the next figure to identify these connectors described in the next table.
Power Power Supply
24V AC (requires both R and C from the HVAC system)
Maximum Power Draw
200mA
Compliance Safety and Emissions
FCC Part 15 | UL Class 2
RoHS
Compliant
Screw-down Connectors on SST-W100 Left Side 24RC
Cooling 24V
24C
G
Fan Output
24RH
Y1
Cooling Stage 1 output (Compressor)
Front View of SST-W100 Backlite Display
Time
Outside Temperature
Relative Humidity
Right Side
W1
24V AC Common (Required) 24V Heating Heat Stage 1 output (standard gas/electric HVAC) Auxiliary Heating (heat pump HVAC)
Setpoints
Y2
Cooling Stage 2 output (Compressor)
W2/O
Heat Stage 2 output (standard gas/electric HVAC) Change Over Valve (heat pump HVAC)
Warmer System Status Colder
Room Temperature
RS2
Remote Sensor 2
RS1
Remote Sensor 1
RS2
Remote Sensor 2
RS1
Remote Sensor 1
RSC
Sensor Shield
RSC
Sensor shield
A1
Menu Heating/Cooling Mode Selection
Fan Mode Selection
Run/Hold Mode Selection
Auxiliary 1 Relay
A2
Auxiliary 2 Relay
NOTE: The Savant Wireless Remote Temperature Sensor (SST-TEMP1) Quick Reference Guide is available at: dealers.SavantSystems.com Savant Hardware > Energy Management
Front View with Callouts
053013
009-0793-02 SST-W100-00
Savant Wireless Thermostat (SST-W100) Quick Reference Guide Standard Gas/Electric HVAC System Wiring
Standard Gas/Electric HVAC System Wiring
Heat Pump HVAC System Wiring
Heat Pump HVAC System Wiring Standard Gas/Electric HVAC System Wiring
Thermostat back
Thermostat back
Optional 24R Connection for single transformer HVAC Systems RC and RH are jumpered together on thermostat board. Cut RC/RH jumper JP1 for separate heating & cooling transformers
Cooling 24V Fan Cooling stage 1 Cooling stage 2 Remote Sensor 2 Remote Sensor 2 Sensor shield
A1 Relay Humidity Relay Com
24RC G Y1 Y2 RS2 RS2 RSC HC A1
24C 24RH W1 W2/O RS1 RS1 RSC H1 A2
Thermostat back For Heat Pump systems, connect the 24R connection to either the 24RC or 24RH Optional 24R Connection for single transformer HVAC Systems RC and RH are jumpered together on thermostat board. Cut RC/RH jumper JP1 for separate heating & cooling transformers
*
24VAC Com
Cooling 24V
24V Heating
CoolingFan 24V Cooling stage Fan1
Heating stage 1 Heating stage 2 Remote Sensor 1
Cooling Coolingstage stage21
Remote Sensor 1
Remote Sensor Cooling stage22
Sensor shield
Remote RemoteSensor Sensor22 Sensor shield2 Remote Sensor
A2Humidity Relay Relay
shield A1 Relay HumiditySensor Relay Com
A1 Relay Humidity Relay Com
Shielded cable
24RC G 24RC Y1 G Y2 Y1 RS2 Y2 RS2 RSC RS2 RSC A1 HC HC
24VAC Com 24V Heating 24VAC Com Heating 24VAux Heating Change Over Heating stage 1 Valve Remote Sensor 1 Heating stage 2 Remote Sensor Remote Sensor 1 1 Sensor shield1 Remote Sensor Sensor shield A2 Relay Humidity Relay
A2Humidity Relay Relay
Shielded cable
Shielded cable Shielded cable Remote Sensor RS2
Shielded cable Shielded cable
Remote Sensor RS1
Remote Sensor RS1 Remote Sensor RS1
Remote RemoteSensor SensorRS2 RS2
Contact Common Closure 24VAC Input
Standard HVAC System Contact Common Contact Closure 24VAC Closure Contact Closure Input Input
Thermostat Connection Optional Feature Humidifier/Dehumidifier
Input
C 24VAC Common
Optional Feature Optional Feature Humidifier/Dehumidifier Humidifier/Dehumidifier
R 24VAC Return W1 Heat Stage1
Common 24VAC
W2 Heat Stage 2 G Fan
Common 24VAC Contact Closure Input
Y1 Compressor Stage 1 Y2 Compressor Stage 2
Thermostat Setup:
Optional Feature Dehumidifier Thermostat Setup: Standard Gas/Electric HVAC Systems To set the HVAC system type, go to the Main Menu Thermostat Info screen and press hold the Setup button. there is and a separate transformer for the heating and cooling
Heat Pump HVAC Systems To set the HVAC system type, go to the Main Menu Optional Feature Thermostat Info screen and press and hold the Setup button.
2. Fan Type. Set the HVAC Fan Type:
x
2
nd
Heat Pump HVAC System Standard HVAC System ThermostatConnection Connection Thermostat 24VAC Common C C24VAC Common R 24VAC Return R 24VAC Return W1 Aux Heat W1 Heat Stage1 O/B Change Over Valve W2 Heat Stage 2 Fan G GFan Compressor Stage Y1Y1 Compressor Stage 1 1 Y2Y2Compressor Stage 2 2 Compressor Stage
Dehumidifier Thermostat Setup:
Default Setup:
NOTE:If system, clip the jumper x HVAC Type: Gas/Elec x board. Fan Type: Gas (JP1)located next to the mini-USB connector on the right side of the circuit 1. Type. Set the HVAC System Type: set to Gas/Elec nd Stage Heat: No
x Deployment 2 Stage Cool:Guide No For installation of the SST-W100 SST-W100 Set to Gas for typicalWireless gas furnaceThermostat, (fan is controlledsee by thethe furnace) available at: dealers.SavantSystems.com Set to Elec for electric heat (fan call with heat call) No setup required for this 3. 2nd Stage Heat. Enable second stage heating outputs Savant Hardware > Energy Management configuration If you have a single stage heating system, leave this set to N If you have a 2 stage heating system, set to Y to enable. 4. 2nd Stage Cool. Enable second stage cooling outputs If you have a single stage cooling system, leave this set to N. If you have a two stage cooling system, set to Y to enable.
DCN: 141-02048-01
24C 24RH 24C W1 24RH W2/O W1 RS1 W2/O RS1 RS1 RSC RS1 RSC A2 H1 H1
Page 19
Standard HVAC Systems 1. Type. Set theGas/Electric HVAC System Type: set to Heat Pump To set the HVAC system type, go to the Main Menu Thermostat Info screen Defaultby Setup: 2. C/O type. Change Over (reversing) Valve Type. Heat pumps change from heating to cooling reversing operation. and press and hold the Setup button. x HVAC Type: Gas/Elec Energy Management If you Ifhave single system, set leave set to N you a have a 2 stage stage heating heating system, to Ythis to enable. Note! If you get heating when you you have 2 stagesecond heatingstage system, set to Y to enable. 4. 2nd IfStage Cool.a Enable cooling outputs expected cooling, change the C/O 4. Aux Heat (HP). IfIfyou youhave have heat strips,system, set thisleave to Y to enable. a auxiliary single stage cooling this set to N. type to the opposite setting. 5. 2nd Stage Cool.If you Enable stagecooling coolingsystem, outputsset to Y to enable. havesecond a two stage If you have a single stage cooling system, leave this set to N. If you have a two stage cooling system, set to Y to enable.
Additional Documentation
DCN: 141-02048-01
DCN: 141-02048-01
Page 19
Page 20
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC. All brand names, product names and trademarks are the property of their respective owners. Savant Systems, LLC reserves the right to change product specifications without notice.
053013
Savant Wireless Thermostat (SST-W100) Quick Reference Guide
The Savant Wireless Thermostat (SST-W100) is a Wi-Fi enabled wireless digital thermostat designed to control Heating, Ventilation and Air Conditioning (HVAC) systems which communicate wirelessly over Wi-Fi to a Savant System. The SST-W100 is designed to integrate seamlessly into a Savant controlled environment.
Holes for mounting on wall screws
Box Contents (1) SST-W100 (1) Installation Kit (xxx) (1) Quick Reference Guide (this document)
Optional Components One of the 16 screw-down connectors used for wiring to climate control devices
SST-TEMP1 - Remote Temperature Sensor
Specifications Environmental Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-condensing)
Rear View of SST-W100
Height
3.96 in/10.06 cm
Wiring
Width
5.775 in/14.67 cm
Depth
.58 in/1.47 cm
Weight
0.5 lb/.23 kg
Dimensions and Weight Screw-down connectors on the inside of the back cover of the SST-W100 are used for wiring connections to various climate control devices. Use the next figure to identify these connectors described in the next table.
Power Power Supply
24V AC (requires both R and C from the HVAC system)
Maximum Power Draw
200mA
Compliance Safety and Emissions
FCC Part 15 | UL Class 2
RoHS
Compliant
Screw-down Connectors on SST-W100 Left Side 24RC
Cooling 24V
24C
G
Fan Output
24RH
Y1
Cooling Stage 1 output (Compressor)
Front View of SST-W100 Backlite Display
Time
Outside Temperature
Relative Humidity
Right Side
W1
24V AC Common (Required) 24V Heating Heat Stage 1 output (standard gas/electric HVAC) Auxiliary Heating (heat pump HVAC)
Setpoints
Y2
Cooling Stage 2 output (Compressor)
W2/O
Heat Stage 2 output (standard gas/electric HVAC) Change Over Valve (heat pump HVAC)
Warmer System Status Colder
Room Temperature
RS2
Remote Sensor 2
RS1
Remote Sensor 1
RS2
Remote Sensor 2
RS1
Remote Sensor 1
RSC
Sensor Shield
RSC
Sensor shield
A1
Menu Heating/Cooling Mode Selection
Fan Mode Selection
Run/Hold Mode Selection
Auxiliary 1 Relay
A2
Auxiliary 2 Relay
NOTE: The Savant Wireless Remote Temperature Sensor (SST-TEMP1) Quick Reference Guide is available at: dealers.SavantSystems.com Savant Hardware > Energy Management
Front View with Callouts
053013
009-0793-02 SST-W100-00
Savant Wireless Thermostat (SST-W100) Quick Reference Guide Standard Gas/Electric HVAC System Wiring
Standard Gas/Electric HVAC System Wiring
Heat Pump HVAC System Wiring
Heat Pump HVAC System Wiring Standard Gas/Electric HVAC System Wiring
Thermostat back
Thermostat back
Optional 24R Connection for single transformer HVAC Systems RC and RH are jumpered together on thermostat board. Cut RC/RH jumper JP1 for separate heating & cooling transformers
Cooling 24V Fan Cooling stage 1 Cooling stage 2 Remote Sensor 2 Remote Sensor 2 Sensor shield
A1 Relay Humidity Relay Com
24RC G Y1 Y2 RS2 RS2 RSC HC A1
24C 24RH W1 W2/O RS1 RS1 RSC H1 A2
Thermostat back For Heat Pump systems, connect the 24R connection to either the 24RC or 24RH Optional 24R Connection for single transformer HVAC Systems RC and RH are jumpered together on thermostat board. Cut RC/RH jumper JP1 for separate heating & cooling transformers
*
24VAC Com
Cooling 24V
24V Heating
CoolingFan 24V Cooling stage Fan1
Heating stage 1 Heating stage 2 Remote Sensor 1
Cooling Coolingstage stage21
Remote Sensor 1
Remote Sensor Cooling stage22
Sensor shield
Remote RemoteSensor Sensor22 Sensor shield2 Remote Sensor
A2Humidity Relay Relay
shield A1 Relay HumiditySensor Relay Com
A1 Relay Humidity Relay Com
Shielded cable
24RC G 24RC Y1 G Y2 Y1 RS2 Y2 RS2 RSC RS2 RSC A1 HC HC
24VAC Com 24V Heating 24VAC Com Heating 24VAux Heating Change Over Heating stage 1 Valve Remote Sensor 1 Heating stage 2 Remote Sensor Remote Sensor 1 1 Sensor shield1 Remote Sensor Sensor shield A2 Relay Humidity Relay
A2Humidity Relay Relay
Shielded cable
Shielded cable Shielded cable Remote Sensor RS2
Shielded cable Shielded cable
Remote Sensor RS1
Remote Sensor RS1 Remote Sensor RS1
Remote RemoteSensor SensorRS2 RS2
Contact Common Closure 24VAC Input
Standard HVAC System Contact Common Contact Closure 24VAC Closure Contact Closure Input Input
Thermostat Connection Optional Feature Humidifier/Dehumidifier
Input
C 24VAC Common
Optional Feature Optional Feature Humidifier/Dehumidifier Humidifier/Dehumidifier
R 24VAC Return W1 Heat Stage1
Common 24VAC
W2 Heat Stage 2 G Fan
Common 24VAC Contact Closure Input
Y1 Compressor Stage 1 Y2 Compressor Stage 2
Thermostat Setup:
Optional Feature Dehumidifier Thermostat Setup: Standard Gas/Electric HVAC Systems To set the HVAC system type, go to the Main Menu Thermostat Info screen and press hold the Setup button. there is and a separate transformer for the heating and cooling
Heat Pump HVAC Systems To set the HVAC system type, go to the Main Menu Optional Feature Thermostat Info screen and press and hold the Setup button.
2. Fan Type. Set the HVAC Fan Type:
x
2
nd
Heat Pump HVAC System Standard HVAC System ThermostatConnection Connection Thermostat 24VAC Common C C24VAC Common R 24VAC Return R 24VAC Return W1 Aux Heat W1 Heat Stage1 O/B Change Over Valve W2 Heat Stage 2 Fan G GFan Compressor Stage Y1Y1 Compressor Stage 1 1 Y2Y2Compressor Stage 2 2 Compressor Stage
Dehumidifier Thermostat Setup:
Default Setup:
NOTE:If system, clip the jumper x HVAC Type: Gas/Elec x board. Fan Type: Gas (JP1)located next to the mini-USB connector on the right side of the circuit 1. Type. Set the HVAC System Type: set to Gas/Elec nd Stage Heat: No
x Deployment 2 Stage Cool:Guide No For installation of the SST-W100 SST-W100 Set to Gas for typicalWireless gas furnaceThermostat, (fan is controlledsee by thethe furnace) available at: dealers.SavantSystems.com Set to Elec for electric heat (fan call with heat call) No setup required for this 3. 2nd Stage Heat. Enable second stage heating outputs Savant Hardware > Energy Management configuration If you have a single stage heating system, leave this set to N If you have a 2 stage heating system, set to Y to enable. 4. 2nd Stage Cool. Enable second stage cooling outputs If you have a single stage cooling system, leave this set to N. If you have a two stage cooling system, set to Y to enable.
DCN: 141-02048-01
24C 24RH 24C W1 24RH W2/O W1 RS1 W2/O RS1 RS1 RSC RS1 RSC A2 H1 H1
Page 19
Standard HVAC Systems 1. Type. Set theGas/Electric HVAC System Type: set to Heat Pump To set the HVAC system type, go to the Main Menu Thermostat Info screen Defaultby Setup: 2. C/O type. Change Over (reversing) Valve Type. Heat pumps change from heating to cooling reversing operation. and press and hold the Setup button. x HVAC Type: Gas/Elec Energy Management If you Ifhave single system, set leave set to N you a have a 2 stage stage heating heating system, to Ythis to enable. Note! If you get heating when you you have 2 stagesecond heatingstage system, set to Y to enable. 4. 2nd IfStage Cool.a Enable cooling outputs expected cooling, change the C/O 4. Aux Heat (HP). IfIfyou youhave have heat strips,system, set thisleave to Y to enable. a auxiliary single stage cooling this set to N. type to the opposite setting. 5. 2nd Stage Cool.If you Enable stagecooling coolingsystem, outputsset to Y to enable. havesecond a two stage If you have a single stage cooling system, leave this set to N. If you have a two stage cooling system, set to Y to enable.
Additional Documentation
DCN: 141-02048-01
DCN: 141-02048-01
Page 19
Page 20
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC. All brand names, product names and trademarks are the property of their respective owners. Savant Systems, LLC reserves the right to change product specifications without notice.
053013
