Sega Genesis II Teardown
Sega Genesis II Teardown
Sega Genesis II Teardown This is a Sega Genesis model 2. In this tear down you will be able to see what the inside of the Sega Genesis should look like.
Written By: Thor Odinson
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Sega Genesis II Teardown
INTRODUCTION This is a Sega Genesis model 2. In this tear down you will be able to see what the inside of the Sega Genesis should look like.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Sega Genesis II Teardown
Step 1 — Sega Genesis II Teardown
Flip the system over
Step 2 — Removing the Screws
Remove the four outer screws (you may want a small cup to keep your screws in.)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
Sega Genesis II Teardown
Step 3
Take plastic top off.
Remove the nine inner screws.
Step 4 — Removing the Screws
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
Sega Genesis II Teardown
Step 5
Remove metal piece.
You now have access to your circuit board. (If you wish to remove the circuit board, continue.)
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Sega Genesis II Teardown
Step 7
Remove the two screws highlighted in picture to remove the circuit board.
Lift the black piece of plactic up.
Step 8
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Sega Genesis II Teardown
Step 9
Lift up the metal piece.
You now have access to the inside of the bottom plastic piece.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Sega Genesis II Teardown
Step 11 — Circuit Board
This is the circuit board.
Step 12 — Reassemble
Do the steps backwards to reassemble.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-21 07:19:49 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
Sega Genesis II Teardown This is a Sega Genesis model 2. In this tear down you will be able to see what the inside of the Sega Genesis should look like.
Written By: Thor Odinson
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Sega Genesis II Teardown
INTRODUCTION This is a Sega Genesis model 2. In this tear down you will be able to see what the inside of the Sega Genesis should look like.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Sega Genesis II Teardown
Step 1 — Sega Genesis II Teardown
Flip the system over
Step 2 — Removing the Screws
Remove the four outer screws (you may want a small cup to keep your screws in.)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
Sega Genesis II Teardown
Step 3
Take plastic top off.
Remove the nine inner screws.
Step 4 — Removing the Screws
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
Sega Genesis II Teardown
Step 5
Remove metal piece.
You now have access to your circuit board. (If you wish to remove the circuit board, continue.)
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Sega Genesis II Teardown
Step 7
Remove the two screws highlighted in picture to remove the circuit board.
Lift the black piece of plactic up.
Step 8
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Sega Genesis II Teardown
Step 9
Lift up the metal piece.
You now have access to the inside of the bottom plastic piece.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Sega Genesis II Teardown
Step 11 — Circuit Board
This is the circuit board.
Step 12 — Reassemble
Do the steps backwards to reassemble.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-21 07:19:49 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
