Shrink-Kon® Heat-Shrinkable Tubing HSC Series End ...
Shrink-Kon Heat-Shrinkable Tubing HSC Series End Caps
Wire Termination — Sta-Kon® Wire Termination & Insulation
®
3:1 Shrink Ratio
• Provides effective method for sealing cable ends, pipe conduit, etc. • Extra thickness at the tip of the end cap prevents sharp ends of the cable from puncturing the seal • Flame retardant • Rated from 600/1000V, 90° continuous use • Shrink temperature of 120° C • Resistant to common fluids and solvents • Adhesive liner provides complete environmental protection and insulation • Heat indicating lines. Continuous operating temperature: -55° C to 110° C
HSC Series Heat-Shrinkable End Caps CAT. NO. HSC8-4 HSC2-20 HSC30-250 HSC300-600 HSC700-1000 HSC750 HSC300* HSC500*
MIN. MAX EXPANDED RECOVERED RECOVERED I.D. (IN.) I.D. (IN.) WALLED (IN.)
.51 .75 1.10 1.50 2.00 2.70 3.50 4.70
.16 .24 .35 .47 .63 .87 1.18 1.57
.09 .09 .12 .16 .16 .16 .16 .17
CODE CABLE SIZE
STANDARD STD. LENGTH (IN.) PKG. QTY.
#8–#6 AWG #6–#2 AWG #1–3/0 AWG 2/0 AWG–350 kcmil 250–500 kcmil 600–1000 kcmil 800–1250 kcmil 1500–2500 kcmil
2.50 2.50 3.00 3.50 3.50 4.00 4.50 5.50
10 10 5 5 5 10 5 5
Order multiple is std. pkg. *Not UL Listed or CSA Certified.
.............................................................................. HSC Series Specifications................................................................................. Property
G-64
test method
typical performance
Physical • Tensile Strength • Elongation • Elongation after Heat Aging (168 hrs. at 150° C) • Heat Shock (4 hrs. at 225° C)
ASTM D412, ISO 37 ASTM D412, ISO 37 ASTM D2671
2100 psi (14.5MPa) 550% 500%
ASTM D2671
• Longitudinal Change on Recovery
ASTM D2671
• Low-Temperature Flexibility (4 hrs. at -55° C) • Specific Gravity • Hardness (Shore D) Electrical • Dielectric Strength • Dielectric Voltage Withstand
ASTM D2671
No cracking or flowing +1%, -10% on Recovery No cracking
ASTM D792 ASTM D2240
1.10 50D
ASTM D149 UL 486D
• Volume Resistivity
ASTM D257
500V/Mil (20kV/mm) No Breakdown (2500V, 60 Hz, 1 Min.) 1016 ohm-cm
United States Tel: 901.252.8000 800.816.7809 Fax: 901.252.1354
Property
test method
typical performance
Chemical • Fluid Resistance • Fungus Resistance • Copper Corrosion • Water Absorption
MIL-DTL-23053 ASTM G21 ASTM D2671 ASTM D570
Good to Excellent No Growth No Corrosion .1%
ASTM D1002
130 psi (.91 MPa)
Seal Integrity • Adhesive Lap Shear (1 in./min. at 23° C) • Adhesive Softening Point • Adhesive Peel Strength (300mm/min. at 23° C) — to steel, aluminum, P.E. — PVC • Adhesive Blocking (30° C) • Water Penetration
ASTM E28 92° C ±-5° C ASTM D1000 (mod.)
ASTM D1146 STM 706
• Room Temperature 168 hrs./40 psi • Temp. Cycling (-40° C to 60° C) 50 cycles/15 psi • Burst Pressure
Technical Services Tel: 888.862.3289
www.tnb.com
35 pli 20 pli No Blocking No penetration after 236 hrs. of continuous immersion No leaks No leaks 100 psi (0.70 MPa)
Wire Termination — Sta-Kon® Wire Termination & Insulation
®
3:1 Shrink Ratio
• Provides effective method for sealing cable ends, pipe conduit, etc. • Extra thickness at the tip of the end cap prevents sharp ends of the cable from puncturing the seal • Flame retardant • Rated from 600/1000V, 90° continuous use • Shrink temperature of 120° C • Resistant to common fluids and solvents • Adhesive liner provides complete environmental protection and insulation • Heat indicating lines. Continuous operating temperature: -55° C to 110° C
HSC Series Heat-Shrinkable End Caps CAT. NO. HSC8-4 HSC2-20 HSC30-250 HSC300-600 HSC700-1000 HSC750 HSC300* HSC500*
MIN. MAX EXPANDED RECOVERED RECOVERED I.D. (IN.) I.D. (IN.) WALLED (IN.)
.51 .75 1.10 1.50 2.00 2.70 3.50 4.70
.16 .24 .35 .47 .63 .87 1.18 1.57
.09 .09 .12 .16 .16 .16 .16 .17
CODE CABLE SIZE
STANDARD STD. LENGTH (IN.) PKG. QTY.
#8–#6 AWG #6–#2 AWG #1–3/0 AWG 2/0 AWG–350 kcmil 250–500 kcmil 600–1000 kcmil 800–1250 kcmil 1500–2500 kcmil
2.50 2.50 3.00 3.50 3.50 4.00 4.50 5.50
10 10 5 5 5 10 5 5
Order multiple is std. pkg. *Not UL Listed or CSA Certified.
.............................................................................. HSC Series Specifications................................................................................. Property
G-64
test method
typical performance
Physical • Tensile Strength • Elongation • Elongation after Heat Aging (168 hrs. at 150° C) • Heat Shock (4 hrs. at 225° C)
ASTM D412, ISO 37 ASTM D412, ISO 37 ASTM D2671
2100 psi (14.5MPa) 550% 500%
ASTM D2671
• Longitudinal Change on Recovery
ASTM D2671
• Low-Temperature Flexibility (4 hrs. at -55° C) • Specific Gravity • Hardness (Shore D) Electrical • Dielectric Strength • Dielectric Voltage Withstand
ASTM D2671
No cracking or flowing +1%, -10% on Recovery No cracking
ASTM D792 ASTM D2240
1.10 50D
ASTM D149 UL 486D
• Volume Resistivity
ASTM D257
500V/Mil (20kV/mm) No Breakdown (2500V, 60 Hz, 1 Min.) 1016 ohm-cm
United States Tel: 901.252.8000 800.816.7809 Fax: 901.252.1354
Property
test method
typical performance
Chemical • Fluid Resistance • Fungus Resistance • Copper Corrosion • Water Absorption
MIL-DTL-23053 ASTM G21 ASTM D2671 ASTM D570
Good to Excellent No Growth No Corrosion .1%
ASTM D1002
130 psi (.91 MPa)
Seal Integrity • Adhesive Lap Shear (1 in./min. at 23° C) • Adhesive Softening Point • Adhesive Peel Strength (300mm/min. at 23° C) — to steel, aluminum, P.E. — PVC • Adhesive Blocking (30° C) • Water Penetration
ASTM E28 92° C ±-5° C ASTM D1000 (mod.)
ASTM D1146 STM 706
• Room Temperature 168 hrs./40 psi • Temp. Cycling (-40° C to 60° C) 50 cycles/15 psi • Burst Pressure
Technical Services Tel: 888.862.3289
www.tnb.com
35 pli 20 pli No Blocking No penetration after 236 hrs. of continuous immersion No leaks No leaks 100 psi (0.70 MPa)
