Sikla Catalog - unistrut metal framing system
Framo 80
Notes
Our service staff and application engineers will be pleased to offer you their assistance as to further information in detail, i. e. to answer your questions or to work out in cooperation with you specific solutions with the aid of our own planning software. Unless otherwise stated, all load parameters refer to mainly dead static loads at ambient temperature. The indicated permissible loads should be regarded as nominal or working loads and, unless otherwise denoted, refer to the main direction of the respective load; breaking load values are not indicated. This catalogue may be used by the recipient only. Each part of the catalogue constitutes the property of Sikla GmbH. All technical representations as well as data are given to the best of our knowledge. All representations and drawings are nonbinding. We do not assume any liability whatsoever for typographical mistakes or deficiencies.
03/2012
Modifications and constructional corrections arising particularly from technological development are excepted.
Sample Applications
Process, Power, M&E
Rooftop, Medical Equipment Supports, Structural Ceiling Grids
03/2012
Modular Modules, Carcass Construction
Framo 80
03/2012
1Framo 80
Beam Section TP F 80
Cantilever Bracket AK F 80
Beam Bracket TKO F 80
Page 1-3
Page 1-4
Page 1-5
End Support STA F 80
End Support WBD F 80
Joining Plate AP
Page 1-6
Page 1-7
Page 1-8
Welding Adapter ASA F 80 GPL 100
Channel Adapter SA F 80
Self Forming Screw FLS F 80
Page 1-9
Page 1-10
Page 1-11
Assembly Set P
U-Holder SB F 80
Beam Section Holder TPH F 80
Page 1-12
Page 1-13
Page 1-14
Framo 80 1-1
Framo 80
End Cap ADK F 80
Framo 80 1-2
03/2012
Page 1-15
Framo 80
Beam Section TP F 80 Group: A410 Application Multi-function beam profile for horizontal, vertical and 3-D support structures in a wide variety of building and industrial applications. In addition to the high torsional resistance achieved using a totally closed profile, structural elements and pipe supports can be attached on all 4 sides with virtually no placement restrictions. Specifically designed mounting holes combined with special FLS Self Forming Screws ensure precise component placement and secure form-locked mountings. Technical Data Type
TP F 80
Type
TP F 80
Section modulus Moment of inertia Radius of inertia [in3 ] [in4 ] [in]
0.97
ly: 1.53 lz: 1.53
Cross section A [in2 ]
2.36
1.13
Torsional moment lt [cm 4 ]
Cross section A [cm2 ]
98.22
7.28
iy: 1.16 iz: 1.16
Section modulus Moment of inertia Radius of inertia [cm3 ] [cm4 ] [cm]
15.87
Torsional moment lt [in 4 ]
ly: 63.49 lz: 63.49
iy: 2.95 iz: 2.95
For all values the effect of holes and perforations have been taken into account. Material:
Steel, hcp
Approvals MPA approved Type
03/2012
TP F 80
Weight [lb/ft]
Weight [kg/m]
Qty. [ft]
Qty. [m]
4.23
6.4
10
3
Part number
195031
Framo 80 1-3
Framo 80
Cantilever Bracket AK F 80 Group: A420 Application Ready-to-use element for mounting to Beam Section F 80 and Beam Bracket TKO F 80 or for construction of cross bars with respective connecting element. Version "E" enables construction of a vertically hung Beam Bracket TKO F 80 with a Cantilever Bracket AK F 80 at the lowest point without any overlap of the mounting plate in the vertical plane. Configuration With pre-assembled End Cap ADK F 80 Installation Interlocking connection to Beam Section F 80 by means of 4 Self Forming Screws FLS F 80. Technical Data Type
L [in]
Dimensions of base plate Slots in base plate for [in] [in]
AK F 80-400 15 3/4" 7 1/2" x 3 1/8" x 5/16" AK F 80-800 31 1/2" 7 1/2" x 3 1/8" x 5/16" AK F 80-E-600 23 5/8" 6 1/2" x 3 1/8" x 5/16"
Type AK F 80-E-600
L Dimensions of base plate Slots in base plate for [mm] [mm]
AK F 80-400 400 AK F 80-800 800 AK F 80-E-600 600 Configuration: Material: Plate Beam Section
/8 " /8 " 3 /8 " 3
3
190 x 80 x 8 190 x 80 x 8 165 x 80 x 8
M10 M10 M10
Plate welded to Beam Section F 80 Steel, hcp Steel, hcp
Approvals MPA approved
AK F 80-400 AK F 80-800 AK F 80-E-600
Framo 80 1-4
W [lb]
W [kg]
Quantity [pack]
7.55 12.88 9.92
3.4 5.8 4.5
1 1 1
Part number
192764 192771 110370
03/2012
Type
Framo 80
Beam Bracket TKO F 80 Group: A423 Application Ready-to-use element for mounting to walls, floors, ceilings and also can be mounted to Simotec Systems 100 and 120 or for assembling crossbars with the respective connecting element. Configuration With pre-assembled End Cap ADK F 80. Installation Depending on the situation, different options are recommended: a) Fixing to building structure using 4 heavy duty anchors 1/2" (M12). b) Frictional connection to steel beams (flange width 3 1/8" - 4 3/4" / 80 120 mm) with Assembly Set P2. c) Interlocking connection to beams of System 100 or 120 by means of Bracket Plates FV 100/120. Technical Data Type
L [in]
TKO F80-400 15 /4" TKO F80-800 31 1/2" 3
Type
8 5 /8 " x 8 5 /8 " x 1 /2 " 8 5 /8 " x 8 5 /8 " x 1 /2 "
1 1
/2 " /2 "
L Dimensions of base plate Slots in base plate for [mm] [mm]
TKO F80-400 400 TKO F80-800 800 Configuration Material: Base plate Beam Section
Dimensions of base plate Slots in base plate for [in] [in]
220 x 220 x 12 220 x 220 x 12
M12 M12
Base plate welded to Beam Section F 80 Steel, hcp Steel, hcp
Approvals MPA approved Type
03/2012
TKO F 80-400 TKO F 80-800
W [lb]
W [kg]
Quantity [pack]
14.65 20.42
6.6 9.2
1 1
Part number
192788 192795
Framo 80 1-5
Framo 80
End Support STA F 80 Group: A422 Application In connection with Beam Bracket, Cantilever Bracket or Beam Section F 80, the End Support STA F 80 enables the construction of crossbars and multiple other constructions. The Version "A" is specially conceived for direct connection to cast-in channels built into the building structure.
STA F 80
Installation Depending on the version, following mountings solutions are possible: a) Connection to Beam Section F 80 with system elements by means of 4 Self Forming Screws FLS F 80. b) Screw connection with cast-in channel by means of appropriate T-head bolt or Channel nut with Hexagon bolt (Type "A"). Technical Data Type
STA F 80 STA F 80-E STA F 80-A
Type STA F 80-E
Dimensions of base plate [in]
Slots in base plate for [in]
7 1/2" x 3 1/8" x 5/16" 6 1/2" x 3 1/8" x 5/16" 7 1/2" x 3 1/8" x 5/16"
/8 " /8 " 1 /2 "
Dimensions of base plate [mm]
Slots in base plate for
190 x 80 x 8 165 x 80 x 8 190 x 80 x 8
M10 M10 M12
STA F 80 STA F 80-E STA F 80-A
Configuration: Material: Plate Octagonal element
3
3
Base plate welded to octagonal element F 80 Steel, hcp Steel, hcp
Approvals MPA approved
STA F 80-A
Framo 80 1-6
STA F 80 STA F 80-E STA F 80-A
W [lb]
W [kg]
Quantity [pack]
3.52 3.30 3.74
1.6 1.5 1.7
1 1 1
Part number
192856 192863 192870
03/2012
Type
Framo 80
End Support WBD F 80 Group: A421 Application End Support WBD F 80 is ideal for making supports for wall and floor mounting, as well as crossbars in conjunction with Beam Section F 80. Beside the direct connection to building structure, different base plates allow an immediate connection to various flange widths. For crossbar constructions, version WBD F 80-T has to be used. The octagonal connection allows max. use of section width without interfering screws or plates. Installation Depending on the situation, different options are recommended: a) Fixing to building structure using 4 heavy-duty 1/2" anchors resp. 5/8". b) Frictional connection to steel beams using Assembly Set P2, P3 or respective Beam Clip. c) Form-locking connection to beam systems STF 100 or 120 using Bracket Plates FV 100/120. Technical Data Type
for flange width [in]
Dimensions of base plate [in]
Slots in base plate for [in]
WBD F 80-80/120 3 1 /8 " - 4 3 /4 " 8 5 /8 " x 8 5 /8 " x 1 /2 " 3 1 3 WBD F 80-121/160 4 /4" - 6 /4" 14 /16" x 10 1/4" x 1/2" WBD F 80-161/200 6 1/4" - 7 7/8" 14 3/16" x 12 1/4" x 1/2" WBD F 80-201/300 7 7/8" - 11 3/4" 16 1/2" x 8 5/8" x 1/2" 1 3 WBD F 80-T 3 /8 " - 4 /4 " 8 5 /8 " x 8 5 /8 " x 1 /2 "
Type
for flange width Dimensions of base plate Slots in base plate for [mm] [mm]
WBD F 80-80/120 WBD F 80-121/160 WBD F 80-161/200 WBD F 80-201/300 WBD F 80-T Configuration:
WBD F 80-T
/2 " /2 " 5 /8 " 5 /8 " 1 /2 " 1
1
Material: Plate Square F 80 Octagonal element F 80
80 - 120 121 - 160 161 - 200 201 - 300 80 - 120
220 x 220 x 12 320 x 260 x 12 320 x 310 x 12 420 x 220 x 12 220 x 220 x 12
M12 M12 M16 M16 M12
Base plate welded to square F 80 resp. octagonal element F 80 Steel, hcp Steel, hcp Steel, hcp
Approvals MPA approved Type
03/2012
WBD F 80-80/120 WBD F 80-121/160 WBD F 80-161/200 WBD F 80-201/300 WBD F 80-T
W [lb]
W [kg]
Quantity [pack]
11.46 19.18 22.48 20.72 10.58
5.2 8.7 10.2 9.4 4.8
1 1 1 1 1
Part number
192801 192818 192825 192832 192849
Framo 80 1-7
Framo 80
Joining Plate AP Group: A630 Application Permits the connection of Beam Bracket TKO F 80 to flange widths > 4 3/4", as well as to building structures by means of heavy load anchors. Configuration Joining Plate AP Assembly Set AP: 4 Countersink Screws 1/2" 4 Hexagon Nuts 1/2" 4 Washers Installation 1) Interlocking connection of Joining Plate with Beam Bracket TKO F 80 by means of countersink screws and hexagon nuts. 2a) Fixing to concrete by means of 4 heavy-load anchors 1/2" or 5/8" (from Type AP 161/200 on). 2b) Frictional connection to steel beams by means of Assembly Set P2 or P3 (from Type AP 161/200 on). Technical Data Type
for flange width [in]
Dimension of base plate [in]
Slots in base plate for [in]
AP 121/160 4 3/4" - 6 5/16" 12 3/5" x 10 1/4" x 1/2" AP 161/200 6 5/16" - 7/8" 12 3/5" x 12 1/4" x 1/2" 7 3 AP 201/300 7 /8" - 11 /4" 16 1/2" x 8 11/16" x 1/2"
Type
Dimension of base plate Perforation for Connection to flange width L x B [mm] [mm]
AP 121/160 AP 161/200 AP 201/300
M12 M16 M16
121 - 160 161 - 200 201 - 300
Steel, hcp
Type
AP 121/160 AP 161/200 AP 201/300
Framo 80 1-8
320 x 260 x 12 320 x 310 x 12 420 x 220 x 12
W [lb]
W [kg]
Quantity [pack]
17.42 20.50 18.74
7.9 9.3 8.5
1 1 1
Part number
183953 183962 183980
03/2012
Material:
/2 " /8 " 5 /8 " 1
5
Framo 80
Welding Adapter ASA F 80 GPL 100 Group: A430 Application Element to be used for flexible welding to beams, welding plates or further suitable weldable connection spots. In connection with Beam Bracket TKO, Cantilever Bracket AK or Beam Section F 80, the Welding Adapter allows the construction of crossbars, cantilevers, as well as further construction possiblities. Installation Apply the base plate adapter side to the connecting element and weld on. The weldable hcp-surface requires an aftertreatment of corrosion protection only at and around the weld seam. The other native connection with Beam Section F 80 is done by means of 4 Self Forming Screws FLS F 80. Technical Data Type
Dimension of base plate [in]
Dimension of base plate [mm]
ASA F 80 GPL 100 3 15/16" x 3 15/16" x 13/16" 100 x 100 x 20 Configuration: Adm. load: Cantilever: Crossbar:
Base plate welded to element F 80
Material:
Steel, hcp, weldable
max. 1.0 kNm See Framo Installation Guidelines
Type
03/2012
ASA F 80 GPL 100
W [lb]
W [kg]
Quantity [pack]
5.79
2.63
1
Part number
111741
Framo 80 1-9
Framo 80
Channel Adapter SA F 80 Group: A430 Application Allows the compatibility of 1 - 5/8" framing system (channels 1 5/8" x 1 5/8" or 1 5 /8" x 1 5/8" D) with Beam Section F 80. Simple construction of pipe lines or constructions, optionally with further parts of the Siconnect System. Thanks to the Pressix CC-Technology the channel can be connected directly to the Channel Adapter. Installation Interlocking connection to Beam Section F 80 by using 4 Self Forming Screws FLS F 80. Technical Data Dimension of base plate Slots in base plate [in] [in]
SA F 80-41 7 1/2" x 3 1/8" x 5/16"
Type
Configuration: Material: Plate: U-Profile:
SA F 80-41
Framo 80 1-10
/8 "
Dimension of base plate Slots in base plate [mm]
SA F 80-41
Type
3
190 x 80 x 8
M10
Base plate welded to U-Pofile Steel, hcp Steel, hcp W [lb]
W [kg]
Quantity [pack]
3.10
1.4
1
Part number
192887
03/2012
Type
Framo 80
Self Forming Screw FLS F 80 Group: A430 Application Threaded Self Forming Screw for formlocking connection of Framo system components and Siconnect products to Beam Section F 80. The beam section material is locally cold-hardened due to the non-cutting forming. The high resulting edge-covering and a threaded connection between Self Forming Screw and Beam Section prevents from accidental unscrewing. During assembly process, the special interlocking prevents from overtightening. Technical Data Type
Tightening torque Tightening torque [ft/lbs] [Nm]
FLS F80
44.25
Material:
Steel, hcp
60
Approvals MPA tested Type
03/2012
FLS F 80
W [lb]
W [kg]
Quantity [pack]
0.04
0.02
100
Part number
192512
Framo 80 1-11
Framo 80
Assembly Set P Group: A640 Application Element for connecting Beam Bracket TKO, Angled Beam Bracket SKO or End Support WBD to a beam section. Configuration Type
Set P2 Set P3
Type
Set P2 Set P3
Beam Clip [Qty.]
4 x P2 4 x P3
Beam Clip [Qty.]
4 x P2 4 x P3
Hexagon bolt [Qty.]
Washer [Qty.]
Hexagon nut [Qty.]
4 x 1 /2 " x 3 1 /8 " 8 x 1 /2 " 4 x 5/8" x 3 15/16" 8 x 5/8"
Hexagon bolt 8.8 [Qty.]
Washer [Qty.]
4 x M12 x 80 8 x 12/40 4 x M16 x 100 8 x 16/125
4 x 1 /2 " 4 x 5 /8 "
Hexagon nut [Qty.]
4 x M12 4 x M16
Installation The narrow ends of the Beam Clips must be fixed to the beam flange. Max. perm. torque of all 1/2" bolts: 85 Nm / 62 ft/Ibs (Set P2) Max. perm. torque of all 5/8" bolts: 150 Nm / 110 ft/Ibs (Set P3) Once post-tensioned, the hexagon bolts must not be re-used! Up to flange width: 1 5/16" Technical Data Material: Steel and cast iron, hcp Type
Set P2 Set P3
Framo 80 1-12
W [lb]
W [kg]
Qty. [set]
3.53 4.63
1.6 2.1
1 1
Part number
168494 179147
03/2012
1 set is required
Framo 80
U-Holder SB F 80 Group: A430 Application Connecting element for bilateral fixation of Beam Section F 80, crossbars or cantilevers to steel beams.
SB F 80-40
Configuration Type SB F 80-40: Holder with thread 1/2" Plate 2 Beam Clips P2 2 Hexagon nuts 1/2" 2 Washers Installation U-holder to be used in pairs. Type 40 up to flange width 1 9/16" Technical Data Material: U-Holder Steel, hcp Plate Steel, hcp Beam clip Steel resp. Cast Iron, hcp Nut/Washer Steel, hcp Type
03/2012
SB F 80-40
W [lb]
W [kg]
Quantity [pack]
3.30
1.5
10
Part number
194010
Framo 80 1-13
Framo 80
Beam Section Holder TPH F 80 Group: A430 Application All-embracing, stiffening holder for Beam Section F 80 directly on the provided support directly to free-standing channels or channels set in concrete directly onto other Beam Section F 80 for frame assembly. Technical Data Material: Steel, hcp
TPH F 80
Framo 80 1-14
W [lb]
W [kg]
Quantity [pack]
1.10
0.5
10
Part number
195765
03/2012
Type
Framo 80
End Cap ADK F 80 Group: A430 Application End cap for a clean finish of closing the ends of Beam Section F 80, Cantilever Brackets, as well as Beam Brackets. Technical Data Material: PE, yellow Type
03/2012
ADK F 80
W [lb]
W [kg]
Quantity [pack]
0.06
0.03
25
Part number
192674
Framo 80 1-15
Framo 80 1-16
03/2012
Framo 80
Supports
4Supports S Sliding Support LA - HV
Sliding Support LC - HV
Sliding Support LD - HV
Sliding Support LK – HV 150
Guiding Set FS
Fixed Point Set XS
Approvals
Available on request.
03/2012
Further informations: www.sikla.us/products/simotec
Simotec 2-1
Subassemblies
4Supports
Speed Nut NT CC 41 - for all 1 5/8“ channel profiles, independent of the depth of the channnel Very useful for retaining the channel nut in place when the application calls for the installation of vertical channels or in place, which are difficult to access. Further benefits: ♦ No spring to clash with the slots in the channel profile. ♦ No appearance of settlement after tightening.
Available on request. 03/2012
Further informations: www.sikla.us/products/simotec
Simotec 3-1
Notes
Our service staff and application engineers will be pleased to offer you their assistance as to further information in detail, i. e. to answer your questions or to work out in cooperation with you specific solutions with the aid of our own planning software. Unless otherwise stated, all load parameters refer to mainly dead static loads at ambient temperature. The indicated permissible loads should be regarded as nominal or working loads and, unless otherwise denoted, refer to the main direction of the respective load; breaking load values are not indicated. This catalogue may be used by the recipient only. Each part of the catalogue constitutes the property of Sikla GmbH. All technical representations as well as data are given to the best of our knowledge. All representations and drawings are nonbinding. We do not assume any liability whatsoever for typographical mistakes or deficiencies.
03/2012
Modifications and constructional corrections arising particularly from technological development are excepted.
Sample Applications
Process, Power, M&E
Rooftop, Medical Equipment Supports, Structural Ceiling Grids
03/2012
Modular Modules, Carcass Construction
Framo 80
03/2012
1Framo 80
Beam Section TP F 80
Cantilever Bracket AK F 80
Beam Bracket TKO F 80
Page 1-3
Page 1-4
Page 1-5
End Support STA F 80
End Support WBD F 80
Joining Plate AP
Page 1-6
Page 1-7
Page 1-8
Welding Adapter ASA F 80 GPL 100
Channel Adapter SA F 80
Self Forming Screw FLS F 80
Page 1-9
Page 1-10
Page 1-11
Assembly Set P
U-Holder SB F 80
Beam Section Holder TPH F 80
Page 1-12
Page 1-13
Page 1-14
Framo 80 1-1
Framo 80
End Cap ADK F 80
Framo 80 1-2
03/2012
Page 1-15
Framo 80
Beam Section TP F 80 Group: A410 Application Multi-function beam profile for horizontal, vertical and 3-D support structures in a wide variety of building and industrial applications. In addition to the high torsional resistance achieved using a totally closed profile, structural elements and pipe supports can be attached on all 4 sides with virtually no placement restrictions. Specifically designed mounting holes combined with special FLS Self Forming Screws ensure precise component placement and secure form-locked mountings. Technical Data Type
TP F 80
Type
TP F 80
Section modulus Moment of inertia Radius of inertia [in3 ] [in4 ] [in]
0.97
ly: 1.53 lz: 1.53
Cross section A [in2 ]
2.36
1.13
Torsional moment lt [cm 4 ]
Cross section A [cm2 ]
98.22
7.28
iy: 1.16 iz: 1.16
Section modulus Moment of inertia Radius of inertia [cm3 ] [cm4 ] [cm]
15.87
Torsional moment lt [in 4 ]
ly: 63.49 lz: 63.49
iy: 2.95 iz: 2.95
For all values the effect of holes and perforations have been taken into account. Material:
Steel, hcp
Approvals MPA approved Type
03/2012
TP F 80
Weight [lb/ft]
Weight [kg/m]
Qty. [ft]
Qty. [m]
4.23
6.4
10
3
Part number
195031
Framo 80 1-3
Framo 80
Cantilever Bracket AK F 80 Group: A420 Application Ready-to-use element for mounting to Beam Section F 80 and Beam Bracket TKO F 80 or for construction of cross bars with respective connecting element. Version "E" enables construction of a vertically hung Beam Bracket TKO F 80 with a Cantilever Bracket AK F 80 at the lowest point without any overlap of the mounting plate in the vertical plane. Configuration With pre-assembled End Cap ADK F 80 Installation Interlocking connection to Beam Section F 80 by means of 4 Self Forming Screws FLS F 80. Technical Data Type
L [in]
Dimensions of base plate Slots in base plate for [in] [in]
AK F 80-400 15 3/4" 7 1/2" x 3 1/8" x 5/16" AK F 80-800 31 1/2" 7 1/2" x 3 1/8" x 5/16" AK F 80-E-600 23 5/8" 6 1/2" x 3 1/8" x 5/16"
Type AK F 80-E-600
L Dimensions of base plate Slots in base plate for [mm] [mm]
AK F 80-400 400 AK F 80-800 800 AK F 80-E-600 600 Configuration: Material: Plate Beam Section
/8 " /8 " 3 /8 " 3
3
190 x 80 x 8 190 x 80 x 8 165 x 80 x 8
M10 M10 M10
Plate welded to Beam Section F 80 Steel, hcp Steel, hcp
Approvals MPA approved
AK F 80-400 AK F 80-800 AK F 80-E-600
Framo 80 1-4
W [lb]
W [kg]
Quantity [pack]
7.55 12.88 9.92
3.4 5.8 4.5
1 1 1
Part number
192764 192771 110370
03/2012
Type
Framo 80
Beam Bracket TKO F 80 Group: A423 Application Ready-to-use element for mounting to walls, floors, ceilings and also can be mounted to Simotec Systems 100 and 120 or for assembling crossbars with the respective connecting element. Configuration With pre-assembled End Cap ADK F 80. Installation Depending on the situation, different options are recommended: a) Fixing to building structure using 4 heavy duty anchors 1/2" (M12). b) Frictional connection to steel beams (flange width 3 1/8" - 4 3/4" / 80 120 mm) with Assembly Set P2. c) Interlocking connection to beams of System 100 or 120 by means of Bracket Plates FV 100/120. Technical Data Type
L [in]
TKO F80-400 15 /4" TKO F80-800 31 1/2" 3
Type
8 5 /8 " x 8 5 /8 " x 1 /2 " 8 5 /8 " x 8 5 /8 " x 1 /2 "
1 1
/2 " /2 "
L Dimensions of base plate Slots in base plate for [mm] [mm]
TKO F80-400 400 TKO F80-800 800 Configuration Material: Base plate Beam Section
Dimensions of base plate Slots in base plate for [in] [in]
220 x 220 x 12 220 x 220 x 12
M12 M12
Base plate welded to Beam Section F 80 Steel, hcp Steel, hcp
Approvals MPA approved Type
03/2012
TKO F 80-400 TKO F 80-800
W [lb]
W [kg]
Quantity [pack]
14.65 20.42
6.6 9.2
1 1
Part number
192788 192795
Framo 80 1-5
Framo 80
End Support STA F 80 Group: A422 Application In connection with Beam Bracket, Cantilever Bracket or Beam Section F 80, the End Support STA F 80 enables the construction of crossbars and multiple other constructions. The Version "A" is specially conceived for direct connection to cast-in channels built into the building structure.
STA F 80
Installation Depending on the version, following mountings solutions are possible: a) Connection to Beam Section F 80 with system elements by means of 4 Self Forming Screws FLS F 80. b) Screw connection with cast-in channel by means of appropriate T-head bolt or Channel nut with Hexagon bolt (Type "A"). Technical Data Type
STA F 80 STA F 80-E STA F 80-A
Type STA F 80-E
Dimensions of base plate [in]
Slots in base plate for [in]
7 1/2" x 3 1/8" x 5/16" 6 1/2" x 3 1/8" x 5/16" 7 1/2" x 3 1/8" x 5/16"
/8 " /8 " 1 /2 "
Dimensions of base plate [mm]
Slots in base plate for
190 x 80 x 8 165 x 80 x 8 190 x 80 x 8
M10 M10 M12
STA F 80 STA F 80-E STA F 80-A
Configuration: Material: Plate Octagonal element
3
3
Base plate welded to octagonal element F 80 Steel, hcp Steel, hcp
Approvals MPA approved
STA F 80-A
Framo 80 1-6
STA F 80 STA F 80-E STA F 80-A
W [lb]
W [kg]
Quantity [pack]
3.52 3.30 3.74
1.6 1.5 1.7
1 1 1
Part number
192856 192863 192870
03/2012
Type
Framo 80
End Support WBD F 80 Group: A421 Application End Support WBD F 80 is ideal for making supports for wall and floor mounting, as well as crossbars in conjunction with Beam Section F 80. Beside the direct connection to building structure, different base plates allow an immediate connection to various flange widths. For crossbar constructions, version WBD F 80-T has to be used. The octagonal connection allows max. use of section width without interfering screws or plates. Installation Depending on the situation, different options are recommended: a) Fixing to building structure using 4 heavy-duty 1/2" anchors resp. 5/8". b) Frictional connection to steel beams using Assembly Set P2, P3 or respective Beam Clip. c) Form-locking connection to beam systems STF 100 or 120 using Bracket Plates FV 100/120. Technical Data Type
for flange width [in]
Dimensions of base plate [in]
Slots in base plate for [in]
WBD F 80-80/120 3 1 /8 " - 4 3 /4 " 8 5 /8 " x 8 5 /8 " x 1 /2 " 3 1 3 WBD F 80-121/160 4 /4" - 6 /4" 14 /16" x 10 1/4" x 1/2" WBD F 80-161/200 6 1/4" - 7 7/8" 14 3/16" x 12 1/4" x 1/2" WBD F 80-201/300 7 7/8" - 11 3/4" 16 1/2" x 8 5/8" x 1/2" 1 3 WBD F 80-T 3 /8 " - 4 /4 " 8 5 /8 " x 8 5 /8 " x 1 /2 "
Type
for flange width Dimensions of base plate Slots in base plate for [mm] [mm]
WBD F 80-80/120 WBD F 80-121/160 WBD F 80-161/200 WBD F 80-201/300 WBD F 80-T Configuration:
WBD F 80-T
/2 " /2 " 5 /8 " 5 /8 " 1 /2 " 1
1
Material: Plate Square F 80 Octagonal element F 80
80 - 120 121 - 160 161 - 200 201 - 300 80 - 120
220 x 220 x 12 320 x 260 x 12 320 x 310 x 12 420 x 220 x 12 220 x 220 x 12
M12 M12 M16 M16 M12
Base plate welded to square F 80 resp. octagonal element F 80 Steel, hcp Steel, hcp Steel, hcp
Approvals MPA approved Type
03/2012
WBD F 80-80/120 WBD F 80-121/160 WBD F 80-161/200 WBD F 80-201/300 WBD F 80-T
W [lb]
W [kg]
Quantity [pack]
11.46 19.18 22.48 20.72 10.58
5.2 8.7 10.2 9.4 4.8
1 1 1 1 1
Part number
192801 192818 192825 192832 192849
Framo 80 1-7
Framo 80
Joining Plate AP Group: A630 Application Permits the connection of Beam Bracket TKO F 80 to flange widths > 4 3/4", as well as to building structures by means of heavy load anchors. Configuration Joining Plate AP Assembly Set AP: 4 Countersink Screws 1/2" 4 Hexagon Nuts 1/2" 4 Washers Installation 1) Interlocking connection of Joining Plate with Beam Bracket TKO F 80 by means of countersink screws and hexagon nuts. 2a) Fixing to concrete by means of 4 heavy-load anchors 1/2" or 5/8" (from Type AP 161/200 on). 2b) Frictional connection to steel beams by means of Assembly Set P2 or P3 (from Type AP 161/200 on). Technical Data Type
for flange width [in]
Dimension of base plate [in]
Slots in base plate for [in]
AP 121/160 4 3/4" - 6 5/16" 12 3/5" x 10 1/4" x 1/2" AP 161/200 6 5/16" - 7/8" 12 3/5" x 12 1/4" x 1/2" 7 3 AP 201/300 7 /8" - 11 /4" 16 1/2" x 8 11/16" x 1/2"
Type
Dimension of base plate Perforation for Connection to flange width L x B [mm] [mm]
AP 121/160 AP 161/200 AP 201/300
M12 M16 M16
121 - 160 161 - 200 201 - 300
Steel, hcp
Type
AP 121/160 AP 161/200 AP 201/300
Framo 80 1-8
320 x 260 x 12 320 x 310 x 12 420 x 220 x 12
W [lb]
W [kg]
Quantity [pack]
17.42 20.50 18.74
7.9 9.3 8.5
1 1 1
Part number
183953 183962 183980
03/2012
Material:
/2 " /8 " 5 /8 " 1
5
Framo 80
Welding Adapter ASA F 80 GPL 100 Group: A430 Application Element to be used for flexible welding to beams, welding plates or further suitable weldable connection spots. In connection with Beam Bracket TKO, Cantilever Bracket AK or Beam Section F 80, the Welding Adapter allows the construction of crossbars, cantilevers, as well as further construction possiblities. Installation Apply the base plate adapter side to the connecting element and weld on. The weldable hcp-surface requires an aftertreatment of corrosion protection only at and around the weld seam. The other native connection with Beam Section F 80 is done by means of 4 Self Forming Screws FLS F 80. Technical Data Type
Dimension of base plate [in]
Dimension of base plate [mm]
ASA F 80 GPL 100 3 15/16" x 3 15/16" x 13/16" 100 x 100 x 20 Configuration: Adm. load: Cantilever: Crossbar:
Base plate welded to element F 80
Material:
Steel, hcp, weldable
max. 1.0 kNm See Framo Installation Guidelines
Type
03/2012
ASA F 80 GPL 100
W [lb]
W [kg]
Quantity [pack]
5.79
2.63
1
Part number
111741
Framo 80 1-9
Framo 80
Channel Adapter SA F 80 Group: A430 Application Allows the compatibility of 1 - 5/8" framing system (channels 1 5/8" x 1 5/8" or 1 5 /8" x 1 5/8" D) with Beam Section F 80. Simple construction of pipe lines or constructions, optionally with further parts of the Siconnect System. Thanks to the Pressix CC-Technology the channel can be connected directly to the Channel Adapter. Installation Interlocking connection to Beam Section F 80 by using 4 Self Forming Screws FLS F 80. Technical Data Dimension of base plate Slots in base plate [in] [in]
SA F 80-41 7 1/2" x 3 1/8" x 5/16"
Type
Configuration: Material: Plate: U-Profile:
SA F 80-41
Framo 80 1-10
/8 "
Dimension of base plate Slots in base plate [mm]
SA F 80-41
Type
3
190 x 80 x 8
M10
Base plate welded to U-Pofile Steel, hcp Steel, hcp W [lb]
W [kg]
Quantity [pack]
3.10
1.4
1
Part number
192887
03/2012
Type
Framo 80
Self Forming Screw FLS F 80 Group: A430 Application Threaded Self Forming Screw for formlocking connection of Framo system components and Siconnect products to Beam Section F 80. The beam section material is locally cold-hardened due to the non-cutting forming. The high resulting edge-covering and a threaded connection between Self Forming Screw and Beam Section prevents from accidental unscrewing. During assembly process, the special interlocking prevents from overtightening. Technical Data Type
Tightening torque Tightening torque [ft/lbs] [Nm]
FLS F80
44.25
Material:
Steel, hcp
60
Approvals MPA tested Type
03/2012
FLS F 80
W [lb]
W [kg]
Quantity [pack]
0.04
0.02
100
Part number
192512
Framo 80 1-11
Framo 80
Assembly Set P Group: A640 Application Element for connecting Beam Bracket TKO, Angled Beam Bracket SKO or End Support WBD to a beam section. Configuration Type
Set P2 Set P3
Type
Set P2 Set P3
Beam Clip [Qty.]
4 x P2 4 x P3
Beam Clip [Qty.]
4 x P2 4 x P3
Hexagon bolt [Qty.]
Washer [Qty.]
Hexagon nut [Qty.]
4 x 1 /2 " x 3 1 /8 " 8 x 1 /2 " 4 x 5/8" x 3 15/16" 8 x 5/8"
Hexagon bolt 8.8 [Qty.]
Washer [Qty.]
4 x M12 x 80 8 x 12/40 4 x M16 x 100 8 x 16/125
4 x 1 /2 " 4 x 5 /8 "
Hexagon nut [Qty.]
4 x M12 4 x M16
Installation The narrow ends of the Beam Clips must be fixed to the beam flange. Max. perm. torque of all 1/2" bolts: 85 Nm / 62 ft/Ibs (Set P2) Max. perm. torque of all 5/8" bolts: 150 Nm / 110 ft/Ibs (Set P3) Once post-tensioned, the hexagon bolts must not be re-used! Up to flange width: 1 5/16" Technical Data Material: Steel and cast iron, hcp Type
Set P2 Set P3
Framo 80 1-12
W [lb]
W [kg]
Qty. [set]
3.53 4.63
1.6 2.1
1 1
Part number
168494 179147
03/2012
1 set is required
Framo 80
U-Holder SB F 80 Group: A430 Application Connecting element for bilateral fixation of Beam Section F 80, crossbars or cantilevers to steel beams.
SB F 80-40
Configuration Type SB F 80-40: Holder with thread 1/2" Plate 2 Beam Clips P2 2 Hexagon nuts 1/2" 2 Washers Installation U-holder to be used in pairs. Type 40 up to flange width 1 9/16" Technical Data Material: U-Holder Steel, hcp Plate Steel, hcp Beam clip Steel resp. Cast Iron, hcp Nut/Washer Steel, hcp Type
03/2012
SB F 80-40
W [lb]
W [kg]
Quantity [pack]
3.30
1.5
10
Part number
194010
Framo 80 1-13
Framo 80
Beam Section Holder TPH F 80 Group: A430 Application All-embracing, stiffening holder for Beam Section F 80 directly on the provided support directly to free-standing channels or channels set in concrete directly onto other Beam Section F 80 for frame assembly. Technical Data Material: Steel, hcp
TPH F 80
Framo 80 1-14
W [lb]
W [kg]
Quantity [pack]
1.10
0.5
10
Part number
195765
03/2012
Type
Framo 80
End Cap ADK F 80 Group: A430 Application End cap for a clean finish of closing the ends of Beam Section F 80, Cantilever Brackets, as well as Beam Brackets. Technical Data Material: PE, yellow Type
03/2012
ADK F 80
W [lb]
W [kg]
Quantity [pack]
0.06
0.03
25
Part number
192674
Framo 80 1-15
Framo 80 1-16
03/2012
Framo 80
Supports
4Supports S Sliding Support LA - HV
Sliding Support LC - HV
Sliding Support LD - HV
Sliding Support LK – HV 150
Guiding Set FS
Fixed Point Set XS
Approvals
Available on request.
03/2012
Further informations: www.sikla.us/products/simotec
Simotec 2-1
Subassemblies
4Supports
Speed Nut NT CC 41 - for all 1 5/8“ channel profiles, independent of the depth of the channnel Very useful for retaining the channel nut in place when the application calls for the installation of vertical channels or in place, which are difficult to access. Further benefits: ♦ No spring to clash with the slots in the channel profile. ♦ No appearance of settlement after tightening.
Available on request. 03/2012
Further informations: www.sikla.us/products/simotec
Simotec 3-1
