Sony Pulse Elite Edition Speaker Replacement
Sony Pulse Elite Edition Speaker Replacement
Sony Pulse Elite Edition Speaker Replacement A guide on replacing the speaker inside a Sony Pulse Elite Edition.
Written By: Armon Davani
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Sony Pulse Elite Edition Speaker Replacement
INTRODUCTION This guide demonstrates how to open up your headset and locate the speaker for replacement if it stops working.
TOOLS: Super Glue (1) Spudger (1) Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Sony Pulse Elite Edition Speaker Replacement
Step 1 — Identifying Earpiece
Locate the side designation on the headband-earpiece junction.
The battery is in the right earpiece.
The motherboard is in the left earpiece.
Step 2 — Ear Cushion Removal
Gently pull around the perimeter of the ear cushion until it comes off.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Sony Pulse Elite Edition Speaker Replacement
Step 3 — Outer Ear Rim Removal
Use the PH00 Screwdriver to remove the three Phillips 6mm screws around the perimeter of the ear cup.
Gently pull the outer ear rim off of the headset assembly.
Harsh removal may cause permanent damage to the speaker wires. Step 4 — Remove Speaker Housing
© iFixit — CC BY-NC-SA
www.iFixit.com
Using tweezers, gently pry the red and black speaker wires from the attached socket.
Page 4 of 6
Sony Pulse Elite Edition Speaker Replacement
Step 5 — Speaker
Locate the junction of the electrical speaker and the plastic speaker housing.
Use the spudger to sever the glue at this junction.
Remove the electrical speaker from the speaker housing.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Use super glue to fasten the replacement speaker into the speaker housing.
Page 5 of 6
Sony Pulse Elite Edition Speaker Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-21 06:59:46 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Sony Pulse Elite Edition Speaker Replacement A guide on replacing the speaker inside a Sony Pulse Elite Edition.
Written By: Armon Davani
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Sony Pulse Elite Edition Speaker Replacement
INTRODUCTION This guide demonstrates how to open up your headset and locate the speaker for replacement if it stops working.
TOOLS: Super Glue (1) Spudger (1) Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Sony Pulse Elite Edition Speaker Replacement
Step 1 — Identifying Earpiece
Locate the side designation on the headband-earpiece junction.
The battery is in the right earpiece.
The motherboard is in the left earpiece.
Step 2 — Ear Cushion Removal
Gently pull around the perimeter of the ear cushion until it comes off.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Sony Pulse Elite Edition Speaker Replacement
Step 3 — Outer Ear Rim Removal
Use the PH00 Screwdriver to remove the three Phillips 6mm screws around the perimeter of the ear cup.
Gently pull the outer ear rim off of the headset assembly.
Harsh removal may cause permanent damage to the speaker wires. Step 4 — Remove Speaker Housing
© iFixit — CC BY-NC-SA
www.iFixit.com
Using tweezers, gently pry the red and black speaker wires from the attached socket.
Page 4 of 6
Sony Pulse Elite Edition Speaker Replacement
Step 5 — Speaker
Locate the junction of the electrical speaker and the plastic speaker housing.
Use the spudger to sever the glue at this junction.
Remove the electrical speaker from the speaker housing.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Use super glue to fasten the replacement speaker into the speaker housing.
Page 5 of 6
Sony Pulse Elite Edition Speaker Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-21 06:59:46 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
