Toyota Corolla Hatch
B1900
PARTS, SERVICE & ACCESSORIES
Toyota Corolla Hatch March 2007 Production Onwards
ACRYLIC BONNET PROTECTOR Installation Instructions Accessory Part No. PZQ15-12050
Installation Time: Approx. 20 mins
Place these instructions in vehicle’s glove box after installation is complete
Care Instructions: Clean Bonnet Protector with a mild detergent and water solution.
Do not slam bonnet.
Item
1
2
ISSUE 1: 15/01/07
Do not use automatic car wash.
Qty
Part number
Bonnet Protector Set
1
PZQ15-12050
Large Metal Clips
2
Small Metal Clips
3
Large Rubber Gaskets
2
Small Rubber Gaskets
3
Screw Plugs
2
Large Abrasive Resistant Tape
2
Small Abrasive Resistant Tape
3
Self Tapping Screws
2
Washers
5
Small Screws
5
Alcohol Wipe
1
Fitting Instruction
1
Component Name
Part No. PZQ15-12050
Do not use abrasive, spirit or solvent based cleaners.
PZQ15-12050FK
Page 1 of 4
COROLLA HATCH ACRYLIC BONNET PROTECTOR Accessory Part No. PZQ15-12050
B1900
x 2 LARGE METAL CLIPS x 3 SMALL METAL CLIPS x 2 LARGE RUBBER GASKETS x 3 SMALL RUBBER GASKETS x 2 SCREW PLUGS x 2 LARGE ABRASIVE RESISTANT TAPE x 3 SMALL ABRASIVE RESISTANT TAPE x 2 SELF TAPPING SCREWS x 5 WASHERS x 5 SMALL SCREWS x 1 ALCOHOL WIPE x 1 FITTING INSTRUCTION FITTING KIT PZQ15-12050FK
BONNET PROTECTOR PZQ15-12050
ISSUE 1: 15/01/07
Part No. PZQ15-12050
Page 2 of 4
PARTS, SERVICE & ACCESSORIES
Diagram #: 1
COROLLA HATCH ACRYLIC BONNET PROTECTOR Accessory Part No. PZQ15-12050
B1900
1. Open & thoroughly clean and dry the bonnet. Locate and mark the centreline of the underside of the bonnet. Trial fit Bonnet Protector centrally onto bonnet. Note the holes in the underside of the bonnet that correspond to the large metal clips. Also note the centre and outer small metal clip positions, then mark these positions onto the bonnet with a pencil or non-permanent marker. Remove Bonnet Protector. See Dia #1. 2. Clean the lip of the bonnet at the five (5) metal clip locations. Wipe away any residue with a clean, dry cloth. Adhere the large abrasive resistant tape strips to the edge of the bonnet at the large metal clip locations, as shown. Apply tape so approximately half of each strip is adhered to the topside and half is adhered to the underside of bonnet. See Dia #2.
Diagram #: 2
3. Adhere the small abrasive resistant tape strips to the edge of the bonnet at the small metal clip locations, as shown. Apply tape strips as per Step 2. See Dia #3.
Diagram #: 3
4. Remove the backing from the large rubber gaskets and attach each gasket to the face of each large metal clip, as shown. Install the large metal clips over the abrasive resistant tape strips at the locations shown. Secure the clips to the bonnet with the screw plugs and self tapping screws provided. Ensure the correct orientation of the screw plugs, as shown. See Dia #4. IMPORTANT: Ensure the clips are positioned over abrasive resistant tape and do not come in contact with any of the bonnet’s paint work. Failure to do this may result in permanent paint damage.
Diagram #: 4 ISSUE 1: 15/01/07
Part No. PZQ15-12050
Page 3 of 4
PARTS, SERVICE & ACCESSORIES
COROLLA HATCH ACRYLIC BONNET PROTECTOR Accessory Part No. PZQ15-12050
B1900
5. Remove the backing from the small rubber gaskets and attach each gasket to the face of each small metal clip, as shown. Install the small metal clips over the abrasive resistant tape strips at the locations shown. See Dia #5. IMPORTANT: Ensure the clips are fully seated over abrasive resistant tape. Ensure the clips do not come in contact with any of the bonnet’s paint work. Failure to do this may result in permanent paint damage.
Diagram #:5
6. Secure the Bonnet Protector to the large metal clips with the small screws and washers provided. See Dia #6.
Diagram #:6
7. Finally, secure the Bonnet Protector to the small metal clips with the small screws and washers provided. See Dia #7.
Diagram #:7
ISSUE 1: 15/01/07
Part No. PZQ15-12050
Page 4 of 4
PARTS, SERVICE & ACCESSORIES
Toyota Corolla Hatch March 2007 Production Onwards
ACRYLIC BONNET PROTECTOR Installation Instructions Accessory Part No. PZQ15-12050
Installation Time: Approx. 20 mins
Place these instructions in vehicle’s glove box after installation is complete
Care Instructions: Clean Bonnet Protector with a mild detergent and water solution.
Do not slam bonnet.
Item
1
2
ISSUE 1: 15/01/07
Do not use automatic car wash.
Qty
Part number
Bonnet Protector Set
1
PZQ15-12050
Large Metal Clips
2
Small Metal Clips
3
Large Rubber Gaskets
2
Small Rubber Gaskets
3
Screw Plugs
2
Large Abrasive Resistant Tape
2
Small Abrasive Resistant Tape
3
Self Tapping Screws
2
Washers
5
Small Screws
5
Alcohol Wipe
1
Fitting Instruction
1
Component Name
Part No. PZQ15-12050
Do not use abrasive, spirit or solvent based cleaners.
PZQ15-12050FK
Page 1 of 4
COROLLA HATCH ACRYLIC BONNET PROTECTOR Accessory Part No. PZQ15-12050
B1900
x 2 LARGE METAL CLIPS x 3 SMALL METAL CLIPS x 2 LARGE RUBBER GASKETS x 3 SMALL RUBBER GASKETS x 2 SCREW PLUGS x 2 LARGE ABRASIVE RESISTANT TAPE x 3 SMALL ABRASIVE RESISTANT TAPE x 2 SELF TAPPING SCREWS x 5 WASHERS x 5 SMALL SCREWS x 1 ALCOHOL WIPE x 1 FITTING INSTRUCTION FITTING KIT PZQ15-12050FK
BONNET PROTECTOR PZQ15-12050
ISSUE 1: 15/01/07
Part No. PZQ15-12050
Page 2 of 4
PARTS, SERVICE & ACCESSORIES
Diagram #: 1
COROLLA HATCH ACRYLIC BONNET PROTECTOR Accessory Part No. PZQ15-12050
B1900
1. Open & thoroughly clean and dry the bonnet. Locate and mark the centreline of the underside of the bonnet. Trial fit Bonnet Protector centrally onto bonnet. Note the holes in the underside of the bonnet that correspond to the large metal clips. Also note the centre and outer small metal clip positions, then mark these positions onto the bonnet with a pencil or non-permanent marker. Remove Bonnet Protector. See Dia #1. 2. Clean the lip of the bonnet at the five (5) metal clip locations. Wipe away any residue with a clean, dry cloth. Adhere the large abrasive resistant tape strips to the edge of the bonnet at the large metal clip locations, as shown. Apply tape so approximately half of each strip is adhered to the topside and half is adhered to the underside of bonnet. See Dia #2.
Diagram #: 2
3. Adhere the small abrasive resistant tape strips to the edge of the bonnet at the small metal clip locations, as shown. Apply tape strips as per Step 2. See Dia #3.
Diagram #: 3
4. Remove the backing from the large rubber gaskets and attach each gasket to the face of each large metal clip, as shown. Install the large metal clips over the abrasive resistant tape strips at the locations shown. Secure the clips to the bonnet with the screw plugs and self tapping screws provided. Ensure the correct orientation of the screw plugs, as shown. See Dia #4. IMPORTANT: Ensure the clips are positioned over abrasive resistant tape and do not come in contact with any of the bonnet’s paint work. Failure to do this may result in permanent paint damage.
Diagram #: 4 ISSUE 1: 15/01/07
Part No. PZQ15-12050
Page 3 of 4
PARTS, SERVICE & ACCESSORIES
COROLLA HATCH ACRYLIC BONNET PROTECTOR Accessory Part No. PZQ15-12050
B1900
5. Remove the backing from the small rubber gaskets and attach each gasket to the face of each small metal clip, as shown. Install the small metal clips over the abrasive resistant tape strips at the locations shown. See Dia #5. IMPORTANT: Ensure the clips are fully seated over abrasive resistant tape. Ensure the clips do not come in contact with any of the bonnet’s paint work. Failure to do this may result in permanent paint damage.
Diagram #:5
6. Secure the Bonnet Protector to the large metal clips with the small screws and washers provided. See Dia #6.
Diagram #:6
7. Finally, secure the Bonnet Protector to the small metal clips with the small screws and washers provided. See Dia #7.
Diagram #:7
ISSUE 1: 15/01/07
Part No. PZQ15-12050
Page 4 of 4
