Type 410QDT DE-Data-Sheet
TECHNICAL DATA SHEET
Type 410 QDT
(UNS S41000)
S TA I N L E S S S T E E L A L L O Y Chemical Composition Chemical Composition (wt%) limits as specified in ASTM A276 and ASME SA276* Element Carbon Chromium Manganese Silicon Phosphorus Sulfur
Description
Type 410 QDT is a quenched and double tempered, 12 percent chromium martensitic stainless steel suitable for general purpose applications that is corrosion resistant to fresh water and mild acids and alkalies. Type 410 is suitable for applications not demanding high corrosion resistance and can be used up to 1200˚F (649˚C) where resistance to scaling and oxidation is required. Type 410 is used for pumps and oil refinery equipment, nuclear and airframe applications, and vanes and blades in jet engine compressors. Type 410 possesses resistance to atmospheric corrosion because it forms a tightly adherent oxide film that protects the surface from attack. The maximum corrosion resistance is obtained by hardening and polishing to a smooth surface finish. Type 410 resists oxidation up to 1500˚F (816˚C) but for continuous service the temperature should not exceed 1200˚F (649˚C). A wide range of properties may be obtained by hardening and tempering this stainless steel. This material is double tempered after quenching to relieve internal stresses and it also guarantees that no untempered martensite remains in the bar.
Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. © 2015 Double Eagle Alloys Inc. All rights reserved.
410 0.08-0.15 11.5-13.5 1.00 1.00 0.040 0.030
* Maximum, unless range is indicated
Mechanical Properties Mechanical property requirements for annealed, hot finished product as specified in ASTM A276 and ASME SA276. Property Yield Strength, min. (ksi) Tensile Strength, min. (ksi) Elongation, min. (%)
410 40 70 20
Physical Properties Physical properties for Type 410 Stainless Steel Property Density, lb/in3 Modulus of Elasticity, psi Coefficient of Thermal Expansion, 68-212˚F, /˚F Thermal Conductivity, Btu/ft hr ˚F Specific Heat, Btu/lb ˚F Electrical Resistivity, Microhm-in
410 Data 0.276 29.0 x 106 6.5 x 10-6 14.4 0.11 22.4
Standards Typical standards for Type 410 Stainless Steel Type 410 ASTM A276 ASTM A479 ASME SA276 ASME SA479
Double Eagle Alloys 1660 N 168th E Avenue Tulsa, OK 74116 Phone: (918) 254-1100 Fax: (918) 254-1101
w w w. d o u b l e e a g l e a l l o y s . c o m
Type 410 QDT
(UNS S41000)
S TA I N L E S S S T E E L A L L O Y Chemical Composition Chemical Composition (wt%) limits as specified in ASTM A276 and ASME SA276* Element Carbon Chromium Manganese Silicon Phosphorus Sulfur
Description
Type 410 QDT is a quenched and double tempered, 12 percent chromium martensitic stainless steel suitable for general purpose applications that is corrosion resistant to fresh water and mild acids and alkalies. Type 410 is suitable for applications not demanding high corrosion resistance and can be used up to 1200˚F (649˚C) where resistance to scaling and oxidation is required. Type 410 is used for pumps and oil refinery equipment, nuclear and airframe applications, and vanes and blades in jet engine compressors. Type 410 possesses resistance to atmospheric corrosion because it forms a tightly adherent oxide film that protects the surface from attack. The maximum corrosion resistance is obtained by hardening and polishing to a smooth surface finish. Type 410 resists oxidation up to 1500˚F (816˚C) but for continuous service the temperature should not exceed 1200˚F (649˚C). A wide range of properties may be obtained by hardening and tempering this stainless steel. This material is double tempered after quenching to relieve internal stresses and it also guarantees that no untempered martensite remains in the bar.
Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. © 2015 Double Eagle Alloys Inc. All rights reserved.
410 0.08-0.15 11.5-13.5 1.00 1.00 0.040 0.030
* Maximum, unless range is indicated
Mechanical Properties Mechanical property requirements for annealed, hot finished product as specified in ASTM A276 and ASME SA276. Property Yield Strength, min. (ksi) Tensile Strength, min. (ksi) Elongation, min. (%)
410 40 70 20
Physical Properties Physical properties for Type 410 Stainless Steel Property Density, lb/in3 Modulus of Elasticity, psi Coefficient of Thermal Expansion, 68-212˚F, /˚F Thermal Conductivity, Btu/ft hr ˚F Specific Heat, Btu/lb ˚F Electrical Resistivity, Microhm-in
410 Data 0.276 29.0 x 106 6.5 x 10-6 14.4 0.11 22.4
Standards Typical standards for Type 410 Stainless Steel Type 410 ASTM A276 ASTM A479 ASME SA276 ASME SA479
Double Eagle Alloys 1660 N 168th E Avenue Tulsa, OK 74116 Phone: (918) 254-1100 Fax: (918) 254-1101
w w w. d o u b l e e a g l e a l l o y s . c o m
