Uncontrolled Copy - MRO Supply
3
4
Uncontrolled Copy
1
2
"C"±.06 5.39 136.91 .75 19.05
.13 3.30
.63 16.00
B
4.33 110.08
2.38 60.45
"AD"
4.14 105.26
2.250 57.150 1.41 35.81 FULL DEPTH
(1) Ø1.13 KNOCKOUT
7.65 194.29
6.52 165.71
WARNING DECAL
"XO"
.19 x .19 x 1.38 KEY
NAMEPLATE
EFF DECAL
6.76 171.70 .8750 .8745 22.2250 22.2123
(3) Ø.88 KNOCKOUT 4.00 101.60
2.25±.09 57.15±2.29
+.00 3.50 -.06 .00 88.90 -1.52
MANUAL PROTECTOR & PROTECTOR RESET DECAL (WHEN REQUIRED)
2.75 69.850
.34 8.636
.119 3.023
5.50 139.700
5.00 127.00 6.50 165.10
A
6.50 165.100
A
NOTE: 1) GASKETS THROUGHOUT
A
PL
E AM
N
TE
ORACLE REV
DRAWING REVISION
REVISION BY
DATE
ECO
APPROVED BY
DATE
E
ECO-0056778
ECO DESCRIPTION
4
B
M. MCCALEB
G. SCHALLOCK
ADDED T-BOLT NUT
8/4/14 8/4/14
COPYRIGHT REGAL BELOIT AMERICA, INC. ALL RIGHTS RESERVED. PROPRIETARY AND CONFIDENTIAL INFORMATION - THIS DOCUMENT IS THE PROPERTY OF REGAL BELOIT AMERICA, INC. ("OWNER") AND CONTAINS OWNER'S PROPRIETARY INFORMATION. ANY PERSON, CORPORATION OR OTHER FIRM RECEIVING IT IS DEEMED, BY RECEIVING IT, TO AGREE THAT IT, AND/OR ANY PART OF IT, SHALL NOT BE DISCLOSED TO ANY PERSON, CORPORATION OR OTHER ENTITY, DUPLICATED, AND/OR USED, EXCEPT AS EXPRESSLY APPROVED IN WRITING IN ADVANCE BY OWNER. THIS DOCUMENT SHALL BE RETURNED TO OWNER UPON REQUEST. IT MAY BE SUBJECT TO CERTAIN RESTRICTIONS UNDER APPLICABLE EXPORT CONTROL LAWS AND REGULATIONS.
3
DRAWN BY TOLERANCES UNLESS JJK OTHERWISE SPECIFIED: DEC. INCH mm ANGLE DATE .X 0.1 [ 2.5] 0.5 06/13/07 .XX 0.03 [ 0.76] APPROVED BY XXX 0.005 [ 0.127] .XXXX 0.0005 [ 0.0127] DATE REMOVE BURRS & BREAK SHARP EDGES: .003/.015 [.076/.381] REFERENCE CORNER FILLETS: .02 [.51] MACHINED SURFACES: 125 3.2 THIRD ANGLE INCH mm PROJECTION mm SHOWN IN [BRACKETS]
2
TM
05
Regal Beloit America, Inc.
DESCRIPTION
OUTLINE TEFC - RIGID
MATERIAL SIZE
B
DRAWING NUMBER
PROCESS/FINISH
GENERAL PURPOSE
028764 1
SHEET
1 OF 1
4
Uncontrolled Copy
1
2
"C"±.06 5.39 136.91 .75 19.05
.13 3.30
.63 16.00
B
4.33 110.08
2.38 60.45
"AD"
4.14 105.26
2.250 57.150 1.41 35.81 FULL DEPTH
(1) Ø1.13 KNOCKOUT
7.65 194.29
6.52 165.71
WARNING DECAL
"XO"
.19 x .19 x 1.38 KEY
NAMEPLATE
EFF DECAL
6.76 171.70 .8750 .8745 22.2250 22.2123
(3) Ø.88 KNOCKOUT 4.00 101.60
2.25±.09 57.15±2.29
+.00 3.50 -.06 .00 88.90 -1.52
MANUAL PROTECTOR & PROTECTOR RESET DECAL (WHEN REQUIRED)
2.75 69.850
.34 8.636
.119 3.023
5.50 139.700
5.00 127.00 6.50 165.10
A
6.50 165.100
A
NOTE: 1) GASKETS THROUGHOUT
A
PL
E AM
N
TE
ORACLE REV
DRAWING REVISION
REVISION BY
DATE
ECO
APPROVED BY
DATE
E
ECO-0056778
ECO DESCRIPTION
4
B
M. MCCALEB
G. SCHALLOCK
ADDED T-BOLT NUT
8/4/14 8/4/14
COPYRIGHT REGAL BELOIT AMERICA, INC. ALL RIGHTS RESERVED. PROPRIETARY AND CONFIDENTIAL INFORMATION - THIS DOCUMENT IS THE PROPERTY OF REGAL BELOIT AMERICA, INC. ("OWNER") AND CONTAINS OWNER'S PROPRIETARY INFORMATION. ANY PERSON, CORPORATION OR OTHER FIRM RECEIVING IT IS DEEMED, BY RECEIVING IT, TO AGREE THAT IT, AND/OR ANY PART OF IT, SHALL NOT BE DISCLOSED TO ANY PERSON, CORPORATION OR OTHER ENTITY, DUPLICATED, AND/OR USED, EXCEPT AS EXPRESSLY APPROVED IN WRITING IN ADVANCE BY OWNER. THIS DOCUMENT SHALL BE RETURNED TO OWNER UPON REQUEST. IT MAY BE SUBJECT TO CERTAIN RESTRICTIONS UNDER APPLICABLE EXPORT CONTROL LAWS AND REGULATIONS.
3
DRAWN BY TOLERANCES UNLESS JJK OTHERWISE SPECIFIED: DEC. INCH mm ANGLE DATE .X 0.1 [ 2.5] 0.5 06/13/07 .XX 0.03 [ 0.76] APPROVED BY XXX 0.005 [ 0.127] .XXXX 0.0005 [ 0.0127] DATE REMOVE BURRS & BREAK SHARP EDGES: .003/.015 [.076/.381] REFERENCE CORNER FILLETS: .02 [.51] MACHINED SURFACES: 125 3.2 THIRD ANGLE INCH mm PROJECTION mm SHOWN IN [BRACKETS]
2
TM
05
Regal Beloit America, Inc.
DESCRIPTION
OUTLINE TEFC - RIGID
MATERIAL SIZE
B
DRAWING NUMBER
PROCESS/FINISH
GENERAL PURPOSE
028764 1
SHEET
1 OF 1
