Viking Installation Guide - Viking Range
Viking Installation Guide
Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200
For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com
Electric Induction Rangetops F20115A
(PS032607JJ)
IMPORTANT – Please Read and Follow!
General Information
• Before beginning, please read and follow these instructions completely and carefully.
• All openings in the wall behind the appliance and/or in the floor under the appliance should be sealed. • Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors. • Disconnect the electrical supply prior to servicing and/or cleaning. • When removing the appliance for service and/or cleaning, disconnect AC power supply and carefully remove the appliance by pulling forward. • Electrical requirements are listed in the product specifications chart. Electrical installation should comply with national and local codes. • DO NOT remove protective packaging until you are ready to perform the installation.
WARNING This appliance should not be used for space heating. This information is based on safety considerations.
• Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
WARNING
• Please observe all local and national codes and ordinances.
ELECTRICAL GROUNDING INSTRUCTIONS This appliance must be electrically in accordance with local codes, or in the absence of local codes, the National Electrical ANSI/NFPA 70, latest edition.
• Please ensure that this product is properly grounded. • Installation must conform with local codes, or in the absence of codes, with the National Electrical Code, ANSI/NFPA 70, latest edition.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
• In CANADA: Electrical installation must be in accordance with the current CSA C22.2 Canadian Electrical Codes Part 1 and/or local codes.
CAUTION Be sure all electrical power is off between the breaker box and the junction box, until the unit is installed and ready to operate. The junction box should be connected to a suitable ground.
Electrical Connection
WARNING Electrical power to the unit must be shut off while line connections are being made. Failure to do so could result in serious injury or death. When making the wire connections, use the entire length of the conduit provided (3 feet). The conduit must not be cut. Connect the red and black leads from the unit conduit to the corresponding leads in the junction box. The bare ground wire in the conduit is connected to the unit frame. When connecting to a 3conductor branch circuit, if local codes permit, connect the bare ground connector lead of the unit to the branch circuit neutral (gray or white in color).
Electrical Requirements
• Installer should leave these instructions with the consumer who should retain for local Inspector’s use and for future reference.
Check your national and local codes regarding this unit. This rangetop is supplied with a 3 wire, 240/208 VAC, 60 Hz conduit which is equipped with a No. 10 ground wire. See electrical connection section for grounding instructions. This unit should be fused separately.
• Consumer should retain this guide for the local Electrical Inspector’s use.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE. SUCH USE MAY RESULT IN A FIRE, ELECTRICAL SHOCK OR OTHER PERSONAL INJURY.
WARNING The use of cabinets for storage above the appliance may result in potential fire or burn hazard. Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to be provided, the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5” (12.7 cm) beyond the bottom of the cabinets.
Back Trim Accessories Assembly and installation instructions are included with all back trim accessories.
1
2
Dimensions & Specifications
Dimensions & Specifications All Induction Rangetop
Induction/Radiant Rangetop Description Overall Width Overall Height From Bottom
VCRT301 29 7/8” (75.9 cm) BASE HEIGHT To top of glass frame 7 7/8” (20.0 cm)
Overall Depth From Rear
Description
VCRT361 35 7/8” (91.1 cm) ADDITIONS TO BASE HEIGHT To top of island trim - add 1 1/4” (3.2 cm) To top of backguard - add 6” (15.2 cm) To top of high-shelf - add 23 1/2” (59.7 cm)
30” (76.2 cm)
35 7/8” (91.1 cm) ADDITIONS TO BASE HEIGHT To top of island trim - add 1 1/4” (3.2 cm) To top of backguard - add 6” (15.2 cm) To top of high-shelf - add 23 1/2” (59.7 cm)
To edge of side panel - 24” (61.0 cm) To end of control panel - 25 15/16” (65.9 cm) To end of knobs - 27 7/16” (69.7 cm)
Cutout Width
36” (91.4 cm)
VIRT361
29 7/8” (75.9 cm) BASE HEIGHT To top of glass frame 7 7/8” (20.0 cm)
Overall Depth From Rear
To edge of side panel - 24” (61.0 cm) To end of control panel - 25 15/16” (65.9 cm) To end of knobs - 27 7/16” (69.7 cm)
Cutout Width
Overall Width Overall Height From Bottom
VIRT301
30” (76.2 cm)
36” (91.4 cm)
Cutout Height
7 1/2” (19.1 cm)
Cutout Height
7 1/2” (19.1 cm)
Cutout Depth
24” (61.0 cm)
Cutout Depth
24” (61.0 cm)
Electrical Requirements
3 - Wire, 240/208 VAC, 60 Hz, electrical connection. Unit is equipped with No. 10 ground wire in conduit. Should be fused separately.
Maximum Amps
240v - 37.9 amps 208v - 32.8 amps
Surface Element Rating
Approx. Shipping Wt.
240v - 55.0 amps 208v - 50.2 amps
240V
208V
Left Front Left Rear
2500 watts 1500 watts
1875 watts 1125 watts
Right Front Right Rear
1200 watts 3300 watts
900 watts 2475 watts
110 lbs. (49.5 kg)
Left Front Left Rear Center Front Bridge Center Rear Right Front Right Rear
240V
208V
2200 watts 1500 watts 1800 watts 800 watts 1800 watts 1200 watts 3300 watts
1650 watts 1125 watts 1350 watts 600 watts 1350 watts 900 watts 2475 watts
125 lbs. (56.2 kg)
Electrical Requirements
3 - Wire, 240/208 VAC, 60 Hz, electrical connection. Unit is equipped with No. 10 ground wire in conduit. Should be fused separately.
Maximum Amps
240v - 37.9 amps 208v - 32.8 amps
Surface Element Rating
Approx. Shipping Wt.
240v - 56.3 amps 208v - 56.3 amps
240V
208V
Left Front Left Rear
2500 watts 1500 watts
1875 watts 1125 watts
Right Front Right Rear
1200 watts 3300 watts
900 watts 2475 watts
110 lbs. (49.5 kg)
240V Left Front Left Rear Center Front Center Rear Right Front Right Rear
2700 1800 2700 1800 1200 3300
208V watts watts watts watts watts watts
2025 watts 1350 watts 2025 watts 1350 watts 900 watts 2475 watts
125 lbs. (56.2 kg)
Minimum Clearance from adjacent combustible construction • Cooking surfaces and below (36” [91.4 cm] and below) • Sides - 0” • Rear - 0” with backguard or highshelf; 0” with island trim and non-combustible wall; 6” (15.2 cm) with island trim and combustible rear wall • Top grate support - 36” (91.4 cm) • Above cooking surface (above 36” [91.4 cm]) • Sides - 6” (15.2 cm) • Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm) above cooking surface. • Wall cabinets directly above product must be minimum 36” (91.4 cm) above cooking surface.
3
4
Installation
Clearances
Proximity to cabinet installation
Interior Cabinet Clearances for proper airflow
1. This rangetop may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. 2. The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36” (91.4 cm) high. There must be a minimum of 6” (15.2 cm) side clearance from the rangetop to such combustible surfaces above the 36” (91.4 cm) counter height. 3. Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above 36” (91.4 cm), the maximum wall cabinet depth must be 13” (33.0 cm) and wall cabinets within this 6” (15.2 cm) side clearance must be 18” (45.7 cm) above the 36” (91.4 cm) high countertop. 4. Wall cabinets above the rangetop must be a minimum of 36” (91.4 cm) above the rangetop cooking surface for the full width of the rangetop.
Detailed View of Bottom Support 2 3/4” (7.0 cm)
1 1/2” dia. cutout for conduit
3” (7.6 cm)
2” (5.1 cm)
8” (20.3 cm)
8” (20.3 cm)
SIDE
FRONT 3” (7.6 cm)
1 1/2” (3.8 cm) Remove the material from this area for proper air flow into the unit. 13” Max 36” Min. (91.4 cm)
(33.0 cm)
7 1/2” (19.1 cm)
6” Min. (15.2 cm)
36” Min. (91.4 cm)
5
18” Min. (45.7 cm)
IMPORTANT: The electronic components for the induction elements in the rangetop need some air circulation. To ensure long life of electronic components, it is required that a minimum of 8” (20.3 cm) of open space remain between the bottom of the unit and any shelf underneath. The maximum length of the shelf underneath is to be 18” (45.7 cm) There should be no partition or shelf directly underneath the unit.
8” Min. (20.3 cm) 18” Max. (45.7 cm)
6
Final Preparation 1. The interior of the oven should be washed thoroughly with hot, soapy water to remove film residues and installation debris before being used for food preparation, then rinsed and wiped dry. Solutions stronger than soapy water are rarely needed. 2. Some stainless steel parts may have a plastic protective wrap, which must be removed. All stainless steel body parts should be washed with hot soapy water and with liquid cleaner designed for this material. If build-up occurs, do not use steel wool, abrasive cloths, cleaners or powders! If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel!! Scratches are almost impossible to remove.
Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted on the inside of the water tank opening. Model number _________________________________________
Serial number _________________________________________
Date of purchase _________________________________________
Date installed _________________________________________
Dealer's name _________________________________________
Address
Service & Parts
_________________________________________
Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.
These installation instructions should remain with the unit for future reference.
Contact Viking Range Corporation, (888) 845-4641, for the nearest service parts distributor in your area.
7
8
Electric All Induction 30” Wide Rangetop Wiring Diagram L2 RED
L1
BLACK
CHASSIS GROUND GREEN
L2C L1C
L2R L1R
POWER LINE CONDITIONER
WHITE
J4
BLUE
J3
J2
J1
POWER BOARD
POWER BOARD
J16
RED BLACK
JOUT1 JOUT2
J17
J3
JE3
AC FAN
JE4
J6
J14
J7
J15
RED SMALL COIL
BLACK
J8
JE5
VIO
SMALL COIL POTENTIOMETER
JE3
GRAY
JE6
RED
RED
J10
BLACK
REAR
JE2 J12 JE7
JE8
LARGE COIL POTENTIOMETER
J13 J2 BLACK RED
JOUT3
J18 J19
JOUT4
BROWN
JE5
VIO
JE6
GRAY
J9
RED
J8
BLACK
REAR
J11
RED
J10
BLACK
FRONT
JE2 J12 JE7
JE8
LARGE COIL POTENTIOMETER
J13 J2
RED
JOUT3
J18 J19
JOUT4
RIGHT SECTION
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
9
SMALL COIL POTENTIOMETER
LED BOARD
J4 J5
CAUTION
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
TEMP CONTROL
JE1
BLACK LARGE COIL
SMALL COIL
J14 J15
J7
TEMP CONTROL
LEFT SECTION
WARNING
J6
EMI BOARD
BLACK
J11
AC FAN
JE4
FRONT
LED BOARD
J4 J5
JOUT2 J3
ORG
EMI BOARD
JOUT1
J17
TEMP CONTROL
JE1 J9
J16
10
TEMP CONTROL
LARGE COIL
Electric Induction/Radiant 30” Wide Rangetop Wiring Diagram L1
L2
BLACK
RED
RED/BLK
RED/BLK
YEL/RED
YEL/RED
WH/RED
RED
RED
BLACK
1500 WATT L.R. ELEM.
RED/BLK
CHASSIS GROUND GREEN
L1
PURPLE
P
BLK WH/RED L2C L1C
RED
L2R
L1R
J2
J1
L2
H1
H2
(H2)
(H1)a
POWER LINE CONDITIONER J4
J3
RED/YEL (H1)b
POWER BOARD
P L2
J16
JOUT1
J17
JOUT2 J3
JE3
ORG
AC FAN
JE4
J6
J14
J7
J15
2500/1000 WATT L. F. ELEM.
ORG
BROWN
RED/BLK RED TEMP CONTROL SMALL COIL POTENTIOMETER
JE1
EMI BOARD JE5
VIO
J4
JE6
GRAY
J5
J9
RED
J8
BLACK
WHITE
J10
YELLOW
FRONT
JE2
JE7
RED/BLK
REAR LED BOARD
J11
J12
BLK
L1
SMALL COIL
PURPLE
BLACK
ORG
RED
JE8
ORG
J2 BLACK
BLK/WH
LARGE COIL POTENTIOMETER
J13
RED
J18
JOUT3
J19
JOUT4
TEMP CONTROL
LARGE COIL
RED
PURPLE
RED
RED
SURF. ELEM. POWER ON LIGHT
ORG
RED RED/BLK
RED/BLK RED
WH/BLK YEL/BLK
WARNING
WH/BLK YEL/BLK
CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
11
12
Electric All Induction 36” Wide Rangetop Wiring Diagram L2 RED
L1 BLACK
CHASSIS GROUND GREEN
L2L
L1L
L2C L1C
L2R
L1R
POWER LINE CONDITIONER J6
J5
J4
J3
J2
J1
WHITE BLUE
POWER BOARD
RED BLACK
J16
JOUT1
J17
JOUT2 J3
JE3
YELLOW
AC FAN
JE4
J6
BLACK
VIO
J4
JE6
GRAY
J5
JOUT1
J17
JOUT2 J3
SMALL COIL POTENTIOMETER
JE1
JE5
J16
TEMP CONTROL
J15
EMI BOARD
WHT/RED
RED
SMALL COIL (FRONT)
J14
J7
POWER BOARD
POWER BOARD
J9
WHITE
J8
YELLOW
RED
J10
BLACK
JE4
J6
J14
J7
J15
BLACK
JE5
VIO
J4
SMALL COIL POTENTIOMETER
JE2
JE6
GRAY
J5
J9
RED
J12 JE8
LARGE COIL POTENTIOMETER
J13
J8
BLACK
J11
WHITE
J10
YELLOW
J2 BLACK RED
J18
JOUT3
J19
JOUT4
J12 JE7
JE8
J2
BLACK
LARGE COIL (REAR)
RED
LEFT SECTION
J18
JOUT3
J19
JOUT4
AC FAN
JE4
J15
REAR
BROWN
VIO
J4
JE6
GRAY
J5
SMALL COIL POTENTIOMETER
J9
WHITE
J8
YELLOW
REAR LED BOARD
J11
RED
J10
BLACK
J12 JE7
JE8
FRONT
LARGE COIL POTENTIOMETER
J13
TEMP CONTROL
J2 BLACK
LARGE COIL (FRONT)
TEMP CONTROL
JE2
RED
J18
JOUT3
J19
JOUT4
RIGHT SECTION
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
13
J7
JE5
CAUTION
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
J14
SMALL COIL (FRONT)
JE1
CENTER SECTION
WARNING
J6
EMI BOARD
LARGE COIL POTENTIOMETER
J13
TEMP CONTROL
JOUT2
FRONT
JE2
JE7
JE3
LED BOARD
FRONT
JOUT1
J17
J3
ORG
EMI BOARD
J16
TEMP CONTROL
JE1
REAR LED BOARD
J11
JE3
AC FAN
RED SMALL COIL (REAR)
14
TEMP CONTROL
LARGE COIL (REAR)
Electric Induction/Radiant 36” Wide Rangetop Wiring Diagram L1
L2
BLACK
RED
RED/BLK
RED/BLK
YEL/RED
YEL/RED
WH/RED
RED
WH/RED
RED/BLK
RED/BLK
BLACK
RED
1500 WATT L.R. ELEM.
RED/BLK
CHASSIS GROUND GREEN PURPLE
WH/RED
L2R
L2C L1C
L
P
YEL/RED
BLK
RED
1
L2
LEFT REAR H2
H1
L1R
POWER LINE CONDITIONER J4
J1
J2
J3
(H1)a
(H2)
RED/YEL (H1)b
POWER BOARD
LEFT FRONT
P
1800 WATT SMALL COIL (FRONT)
BLK BRIDGE ELEM
JE3
1800 WATT
ORG
AC FAN
JE4
J6
J14
J7
J15
WH/BLK
RED/YEL
ORG
ORG
JE5
VIO
J4
JE6
GRAY
J5
J9
RED
J8
BLACK
REAR
RED
RED/BLK
RED
L
P
1
WHITE
MIDDLE REAR H1
J10
YELLOW
FRONT (H1)a
(H2)
JE7
JE8
LARGE COIL POTENTIOMETER
J13 J2
MIDDLE FRONT
(H1)b
TEMP CONTROL
P
RED
J18
JOUT3
J19
JOUT4
LARGE COIL (REAR)
L1
RED/BLK RED
YEL/BLK
BLK/WH
BLK/WHT
L2
BLACK
RED
H2
JE2
ORG
RED
L2
LED BOARD J11
J12
RED/BLK
BLK
SMALL COIL POTENTIOMETER
JE1
EMI BOARD
BROWN
TEMP CONTROL
RED/BLK
YEL/RED
J3
PURPLE
JOUT2
WH/RED
JOUT1
J17
ORG
BLACK
J16
800 WATT
2200/1000 WATT L. F. ELEM.
L1
L2
RED
PURPLE
SURF. ELEM. POWER ON LIGHT
ORG RED
RED
RED RED/BLK
RED/BLK RED WH/BLK
WH/BLK
YEL/BLK
YEL/BLK
WARNING
CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
15
16
Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200
For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com
Electric Induction Rangetops F20115A
(PS032607JJ)
IMPORTANT – Please Read and Follow!
General Information
• Before beginning, please read and follow these instructions completely and carefully.
• All openings in the wall behind the appliance and/or in the floor under the appliance should be sealed. • Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors. • Disconnect the electrical supply prior to servicing and/or cleaning. • When removing the appliance for service and/or cleaning, disconnect AC power supply and carefully remove the appliance by pulling forward. • Electrical requirements are listed in the product specifications chart. Electrical installation should comply with national and local codes. • DO NOT remove protective packaging until you are ready to perform the installation.
WARNING This appliance should not be used for space heating. This information is based on safety considerations.
• Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
WARNING
• Please observe all local and national codes and ordinances.
ELECTRICAL GROUNDING INSTRUCTIONS This appliance must be electrically in accordance with local codes, or in the absence of local codes, the National Electrical ANSI/NFPA 70, latest edition.
• Please ensure that this product is properly grounded. • Installation must conform with local codes, or in the absence of codes, with the National Electrical Code, ANSI/NFPA 70, latest edition.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
• In CANADA: Electrical installation must be in accordance with the current CSA C22.2 Canadian Electrical Codes Part 1 and/or local codes.
CAUTION Be sure all electrical power is off between the breaker box and the junction box, until the unit is installed and ready to operate. The junction box should be connected to a suitable ground.
Electrical Connection
WARNING Electrical power to the unit must be shut off while line connections are being made. Failure to do so could result in serious injury or death. When making the wire connections, use the entire length of the conduit provided (3 feet). The conduit must not be cut. Connect the red and black leads from the unit conduit to the corresponding leads in the junction box. The bare ground wire in the conduit is connected to the unit frame. When connecting to a 3conductor branch circuit, if local codes permit, connect the bare ground connector lead of the unit to the branch circuit neutral (gray or white in color).
Electrical Requirements
• Installer should leave these instructions with the consumer who should retain for local Inspector’s use and for future reference.
Check your national and local codes regarding this unit. This rangetop is supplied with a 3 wire, 240/208 VAC, 60 Hz conduit which is equipped with a No. 10 ground wire. See electrical connection section for grounding instructions. This unit should be fused separately.
• Consumer should retain this guide for the local Electrical Inspector’s use.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE. SUCH USE MAY RESULT IN A FIRE, ELECTRICAL SHOCK OR OTHER PERSONAL INJURY.
WARNING The use of cabinets for storage above the appliance may result in potential fire or burn hazard. Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to be provided, the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5” (12.7 cm) beyond the bottom of the cabinets.
Back Trim Accessories Assembly and installation instructions are included with all back trim accessories.
1
2
Dimensions & Specifications
Dimensions & Specifications All Induction Rangetop
Induction/Radiant Rangetop Description Overall Width Overall Height From Bottom
VCRT301 29 7/8” (75.9 cm) BASE HEIGHT To top of glass frame 7 7/8” (20.0 cm)
Overall Depth From Rear
Description
VCRT361 35 7/8” (91.1 cm) ADDITIONS TO BASE HEIGHT To top of island trim - add 1 1/4” (3.2 cm) To top of backguard - add 6” (15.2 cm) To top of high-shelf - add 23 1/2” (59.7 cm)
30” (76.2 cm)
35 7/8” (91.1 cm) ADDITIONS TO BASE HEIGHT To top of island trim - add 1 1/4” (3.2 cm) To top of backguard - add 6” (15.2 cm) To top of high-shelf - add 23 1/2” (59.7 cm)
To edge of side panel - 24” (61.0 cm) To end of control panel - 25 15/16” (65.9 cm) To end of knobs - 27 7/16” (69.7 cm)
Cutout Width
36” (91.4 cm)
VIRT361
29 7/8” (75.9 cm) BASE HEIGHT To top of glass frame 7 7/8” (20.0 cm)
Overall Depth From Rear
To edge of side panel - 24” (61.0 cm) To end of control panel - 25 15/16” (65.9 cm) To end of knobs - 27 7/16” (69.7 cm)
Cutout Width
Overall Width Overall Height From Bottom
VIRT301
30” (76.2 cm)
36” (91.4 cm)
Cutout Height
7 1/2” (19.1 cm)
Cutout Height
7 1/2” (19.1 cm)
Cutout Depth
24” (61.0 cm)
Cutout Depth
24” (61.0 cm)
Electrical Requirements
3 - Wire, 240/208 VAC, 60 Hz, electrical connection. Unit is equipped with No. 10 ground wire in conduit. Should be fused separately.
Maximum Amps
240v - 37.9 amps 208v - 32.8 amps
Surface Element Rating
Approx. Shipping Wt.
240v - 55.0 amps 208v - 50.2 amps
240V
208V
Left Front Left Rear
2500 watts 1500 watts
1875 watts 1125 watts
Right Front Right Rear
1200 watts 3300 watts
900 watts 2475 watts
110 lbs. (49.5 kg)
Left Front Left Rear Center Front Bridge Center Rear Right Front Right Rear
240V
208V
2200 watts 1500 watts 1800 watts 800 watts 1800 watts 1200 watts 3300 watts
1650 watts 1125 watts 1350 watts 600 watts 1350 watts 900 watts 2475 watts
125 lbs. (56.2 kg)
Electrical Requirements
3 - Wire, 240/208 VAC, 60 Hz, electrical connection. Unit is equipped with No. 10 ground wire in conduit. Should be fused separately.
Maximum Amps
240v - 37.9 amps 208v - 32.8 amps
Surface Element Rating
Approx. Shipping Wt.
240v - 56.3 amps 208v - 56.3 amps
240V
208V
Left Front Left Rear
2500 watts 1500 watts
1875 watts 1125 watts
Right Front Right Rear
1200 watts 3300 watts
900 watts 2475 watts
110 lbs. (49.5 kg)
240V Left Front Left Rear Center Front Center Rear Right Front Right Rear
2700 1800 2700 1800 1200 3300
208V watts watts watts watts watts watts
2025 watts 1350 watts 2025 watts 1350 watts 900 watts 2475 watts
125 lbs. (56.2 kg)
Minimum Clearance from adjacent combustible construction • Cooking surfaces and below (36” [91.4 cm] and below) • Sides - 0” • Rear - 0” with backguard or highshelf; 0” with island trim and non-combustible wall; 6” (15.2 cm) with island trim and combustible rear wall • Top grate support - 36” (91.4 cm) • Above cooking surface (above 36” [91.4 cm]) • Sides - 6” (15.2 cm) • Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm) above cooking surface. • Wall cabinets directly above product must be minimum 36” (91.4 cm) above cooking surface.
3
4
Installation
Clearances
Proximity to cabinet installation
Interior Cabinet Clearances for proper airflow
1. This rangetop may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. 2. The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36” (91.4 cm) high. There must be a minimum of 6” (15.2 cm) side clearance from the rangetop to such combustible surfaces above the 36” (91.4 cm) counter height. 3. Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above 36” (91.4 cm), the maximum wall cabinet depth must be 13” (33.0 cm) and wall cabinets within this 6” (15.2 cm) side clearance must be 18” (45.7 cm) above the 36” (91.4 cm) high countertop. 4. Wall cabinets above the rangetop must be a minimum of 36” (91.4 cm) above the rangetop cooking surface for the full width of the rangetop.
Detailed View of Bottom Support 2 3/4” (7.0 cm)
1 1/2” dia. cutout for conduit
3” (7.6 cm)
2” (5.1 cm)
8” (20.3 cm)
8” (20.3 cm)
SIDE
FRONT 3” (7.6 cm)
1 1/2” (3.8 cm) Remove the material from this area for proper air flow into the unit. 13” Max 36” Min. (91.4 cm)
(33.0 cm)
7 1/2” (19.1 cm)
6” Min. (15.2 cm)
36” Min. (91.4 cm)
5
18” Min. (45.7 cm)
IMPORTANT: The electronic components for the induction elements in the rangetop need some air circulation. To ensure long life of electronic components, it is required that a minimum of 8” (20.3 cm) of open space remain between the bottom of the unit and any shelf underneath. The maximum length of the shelf underneath is to be 18” (45.7 cm) There should be no partition or shelf directly underneath the unit.
8” Min. (20.3 cm) 18” Max. (45.7 cm)
6
Final Preparation 1. The interior of the oven should be washed thoroughly with hot, soapy water to remove film residues and installation debris before being used for food preparation, then rinsed and wiped dry. Solutions stronger than soapy water are rarely needed. 2. Some stainless steel parts may have a plastic protective wrap, which must be removed. All stainless steel body parts should be washed with hot soapy water and with liquid cleaner designed for this material. If build-up occurs, do not use steel wool, abrasive cloths, cleaners or powders! If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel!! Scratches are almost impossible to remove.
Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted on the inside of the water tank opening. Model number _________________________________________
Serial number _________________________________________
Date of purchase _________________________________________
Date installed _________________________________________
Dealer's name _________________________________________
Address
Service & Parts
_________________________________________
Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.
These installation instructions should remain with the unit for future reference.
Contact Viking Range Corporation, (888) 845-4641, for the nearest service parts distributor in your area.
7
8
Electric All Induction 30” Wide Rangetop Wiring Diagram L2 RED
L1
BLACK
CHASSIS GROUND GREEN
L2C L1C
L2R L1R
POWER LINE CONDITIONER
WHITE
J4
BLUE
J3
J2
J1
POWER BOARD
POWER BOARD
J16
RED BLACK
JOUT1 JOUT2
J17
J3
JE3
AC FAN
JE4
J6
J14
J7
J15
RED SMALL COIL
BLACK
J8
JE5
VIO
SMALL COIL POTENTIOMETER
JE3
GRAY
JE6
RED
RED
J10
BLACK
REAR
JE2 J12 JE7
JE8
LARGE COIL POTENTIOMETER
J13 J2 BLACK RED
JOUT3
J18 J19
JOUT4
BROWN
JE5
VIO
JE6
GRAY
J9
RED
J8
BLACK
REAR
J11
RED
J10
BLACK
FRONT
JE2 J12 JE7
JE8
LARGE COIL POTENTIOMETER
J13 J2
RED
JOUT3
J18 J19
JOUT4
RIGHT SECTION
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
9
SMALL COIL POTENTIOMETER
LED BOARD
J4 J5
CAUTION
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
TEMP CONTROL
JE1
BLACK LARGE COIL
SMALL COIL
J14 J15
J7
TEMP CONTROL
LEFT SECTION
WARNING
J6
EMI BOARD
BLACK
J11
AC FAN
JE4
FRONT
LED BOARD
J4 J5
JOUT2 J3
ORG
EMI BOARD
JOUT1
J17
TEMP CONTROL
JE1 J9
J16
10
TEMP CONTROL
LARGE COIL
Electric Induction/Radiant 30” Wide Rangetop Wiring Diagram L1
L2
BLACK
RED
RED/BLK
RED/BLK
YEL/RED
YEL/RED
WH/RED
RED
RED
BLACK
1500 WATT L.R. ELEM.
RED/BLK
CHASSIS GROUND GREEN
L1
PURPLE
P
BLK WH/RED L2C L1C
RED
L2R
L1R
J2
J1
L2
H1
H2
(H2)
(H1)a
POWER LINE CONDITIONER J4
J3
RED/YEL (H1)b
POWER BOARD
P L2
J16
JOUT1
J17
JOUT2 J3
JE3
ORG
AC FAN
JE4
J6
J14
J7
J15
2500/1000 WATT L. F. ELEM.
ORG
BROWN
RED/BLK RED TEMP CONTROL SMALL COIL POTENTIOMETER
JE1
EMI BOARD JE5
VIO
J4
JE6
GRAY
J5
J9
RED
J8
BLACK
WHITE
J10
YELLOW
FRONT
JE2
JE7
RED/BLK
REAR LED BOARD
J11
J12
BLK
L1
SMALL COIL
PURPLE
BLACK
ORG
RED
JE8
ORG
J2 BLACK
BLK/WH
LARGE COIL POTENTIOMETER
J13
RED
J18
JOUT3
J19
JOUT4
TEMP CONTROL
LARGE COIL
RED
PURPLE
RED
RED
SURF. ELEM. POWER ON LIGHT
ORG
RED RED/BLK
RED/BLK RED
WH/BLK YEL/BLK
WARNING
WH/BLK YEL/BLK
CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
11
12
Electric All Induction 36” Wide Rangetop Wiring Diagram L2 RED
L1 BLACK
CHASSIS GROUND GREEN
L2L
L1L
L2C L1C
L2R
L1R
POWER LINE CONDITIONER J6
J5
J4
J3
J2
J1
WHITE BLUE
POWER BOARD
RED BLACK
J16
JOUT1
J17
JOUT2 J3
JE3
YELLOW
AC FAN
JE4
J6
BLACK
VIO
J4
JE6
GRAY
J5
JOUT1
J17
JOUT2 J3
SMALL COIL POTENTIOMETER
JE1
JE5
J16
TEMP CONTROL
J15
EMI BOARD
WHT/RED
RED
SMALL COIL (FRONT)
J14
J7
POWER BOARD
POWER BOARD
J9
WHITE
J8
YELLOW
RED
J10
BLACK
JE4
J6
J14
J7
J15
BLACK
JE5
VIO
J4
SMALL COIL POTENTIOMETER
JE2
JE6
GRAY
J5
J9
RED
J12 JE8
LARGE COIL POTENTIOMETER
J13
J8
BLACK
J11
WHITE
J10
YELLOW
J2 BLACK RED
J18
JOUT3
J19
JOUT4
J12 JE7
JE8
J2
BLACK
LARGE COIL (REAR)
RED
LEFT SECTION
J18
JOUT3
J19
JOUT4
AC FAN
JE4
J15
REAR
BROWN
VIO
J4
JE6
GRAY
J5
SMALL COIL POTENTIOMETER
J9
WHITE
J8
YELLOW
REAR LED BOARD
J11
RED
J10
BLACK
J12 JE7
JE8
FRONT
LARGE COIL POTENTIOMETER
J13
TEMP CONTROL
J2 BLACK
LARGE COIL (FRONT)
TEMP CONTROL
JE2
RED
J18
JOUT3
J19
JOUT4
RIGHT SECTION
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
13
J7
JE5
CAUTION
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
J14
SMALL COIL (FRONT)
JE1
CENTER SECTION
WARNING
J6
EMI BOARD
LARGE COIL POTENTIOMETER
J13
TEMP CONTROL
JOUT2
FRONT
JE2
JE7
JE3
LED BOARD
FRONT
JOUT1
J17
J3
ORG
EMI BOARD
J16
TEMP CONTROL
JE1
REAR LED BOARD
J11
JE3
AC FAN
RED SMALL COIL (REAR)
14
TEMP CONTROL
LARGE COIL (REAR)
Electric Induction/Radiant 36” Wide Rangetop Wiring Diagram L1
L2
BLACK
RED
RED/BLK
RED/BLK
YEL/RED
YEL/RED
WH/RED
RED
WH/RED
RED/BLK
RED/BLK
BLACK
RED
1500 WATT L.R. ELEM.
RED/BLK
CHASSIS GROUND GREEN PURPLE
WH/RED
L2R
L2C L1C
L
P
YEL/RED
BLK
RED
1
L2
LEFT REAR H2
H1
L1R
POWER LINE CONDITIONER J4
J1
J2
J3
(H1)a
(H2)
RED/YEL (H1)b
POWER BOARD
LEFT FRONT
P
1800 WATT SMALL COIL (FRONT)
BLK BRIDGE ELEM
JE3
1800 WATT
ORG
AC FAN
JE4
J6
J14
J7
J15
WH/BLK
RED/YEL
ORG
ORG
JE5
VIO
J4
JE6
GRAY
J5
J9
RED
J8
BLACK
REAR
RED
RED/BLK
RED
L
P
1
WHITE
MIDDLE REAR H1
J10
YELLOW
FRONT (H1)a
(H2)
JE7
JE8
LARGE COIL POTENTIOMETER
J13 J2
MIDDLE FRONT
(H1)b
TEMP CONTROL
P
RED
J18
JOUT3
J19
JOUT4
LARGE COIL (REAR)
L1
RED/BLK RED
YEL/BLK
BLK/WH
BLK/WHT
L2
BLACK
RED
H2
JE2
ORG
RED
L2
LED BOARD J11
J12
RED/BLK
BLK
SMALL COIL POTENTIOMETER
JE1
EMI BOARD
BROWN
TEMP CONTROL
RED/BLK
YEL/RED
J3
PURPLE
JOUT2
WH/RED
JOUT1
J17
ORG
BLACK
J16
800 WATT
2200/1000 WATT L. F. ELEM.
L1
L2
RED
PURPLE
SURF. ELEM. POWER ON LIGHT
ORG RED
RED
RED RED/BLK
RED/BLK RED WH/BLK
WH/BLK
YEL/BLK
YEL/BLK
WARNING
CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
This unit must be properly grounded. See installation instructions for proper grounding instructions. NOTE: Trailers or stripes will be the second color in a color combination.
15
16
