Vtech Touch and Swipe Baby Phone Power Switch Replacement
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Vtech Touch and Swipe Baby Phone Power Switch Replacement The power switch may become sensitive or even unresponsive. This guide will show you how to realign the switch.
Written By: tellocordova
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
TOOLS: Phillips #1 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Step 1 — Battery
Using a Phillips #1 screwdriver, remove the 4.8mm Phillips #1 screw on the battery cover by twisting the screwdriver counter-clockwise.
Step 2
Then simply remove the two AAA batteries by pulling on one end of the battery and lifting it straight out.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Step 3
Take care when you want to close it. There is a notch.
First you have to hook up that notch.
Then firmly use a PH1 screwdriver to secure it.
Step 4 — Power Switch
Remove 4 13.8mm screws holding the device back using a Phillips #1 screw driver.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Step 5
Lift directly up to remove the switch and lay the wire down to the side.
Once the switch has been taken out you can remove the switch's casing.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 05:22:02 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement The power switch may become sensitive or even unresponsive. This guide will show you how to realign the switch.
Written By: tellocordova
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
TOOLS: Phillips #1 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Step 1 — Battery
Using a Phillips #1 screwdriver, remove the 4.8mm Phillips #1 screw on the battery cover by twisting the screwdriver counter-clockwise.
Step 2
Then simply remove the two AAA batteries by pulling on one end of the battery and lifting it straight out.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Step 3
Take care when you want to close it. There is a notch.
First you have to hook up that notch.
Then firmly use a PH1 screwdriver to secure it.
Step 4 — Power Switch
Remove 4 13.8mm screws holding the device back using a Phillips #1 screw driver.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Vtech Touch and Swipe Baby Phone Power Switch Replacement
Step 5
Lift directly up to remove the switch and lay the wire down to the side.
Once the switch has been taken out you can remove the switch's casing.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 05:22:02 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
