WARRANTY: One Year Limited Warranty.
Auto-Off Feature: • • •
®
LASERLYTE
®
• Fits Ruger® LC9 and Kel-Tec® PF9 • Quick and Easy installation • Works with most pocket holsters • Ergonomic activation • Dual laser modes with auto-off feature
LASERLYTE
5 min. 6 min. Off
5 min.
• • • •
®
After 5 minutes in any mode, warning mode pulse will activate. After 1 minute in warning pulse mode, laser will turn off. Press the switch during warning pulse for laser reset.
Batteries: 4-377 batteries Use Allen wrench .050 to remove battery cover Polarity marked on board inside of battery compartment. Note: Dimples on battery cover must be face down. Tighten down the battery cover and check periodically.
CK-AMF9 Patent Pending
Dimples Down
WARRANTY: One Year Limited Warranty.
®
DANGER LASER LIGHT AVOID DIRECT EYE EXPOSURE
POWER OUTPUT < 5mw WAVELENGTH 630-670mm CLASS IIIa PRODUCT
30 N. Alamos Drive - Cottonwood, AZ 86326 Phone 928-649-3201 - Fax 928-649-3970
®
www.LaserLyte.com
REV0512
CK_AMF 9.indd 1
5/16/12 11:36 AM
Kel-Tec®/Ruger® 9mm Side Mount Laser CK-AMF9
INTERNAL LOCK HOLE
LASERLYTE
Unload firearm.
Attach danger label to side of gun near laser with arrow pointing toward front sight.
1
Activation:
1 Press once turns laser on: constant or pulse 2 Press and hold for 5 seconds to change mode. 3 Second press turns laser off. ON/OFF
#1
Read instructions completely before installing your laser. Failure to do so may result in damage to your laser or firearm.
Attach danger label to side of gun near laser with arrow pointing toward front sight.
LASERLYTE
#2
#2
The two LaserLyte® frame pin screws are pre-loaded with a self-locking nylon patch. If you un-install the CK-AMF9, re-apply a self-locking material such as Lock-tite® Threadlocker Blue 242® to the LaserLyte® frame pin screws before re-installing the laser.
LASERLYTE
or LASERLYTE
Laser Sight In:
1 Use the provided .035 Allen wrench to adjust the sight. 2 Always end adjustments on a clockwise turn. 3 Make final adjustments at shooting range.
Do not block internal lock hole (N/A for Keltec®).
Use both .062 Allen wrenches to tighten screws until snug. Do not over tighten! Tighten down the battery cover, and check periodically.
3
LASERLYTE
5 sec.
2
3 Place laser on gun, align holes and insert screws. 4
2
LASERLYTE
1/4”
Using punch and small hammer, drift pin #1 out no more than 1/4”. Immediately insert LaserLyte® mounting pin and tap into place, completely replacing pin #1. 2 Follow the steps for pin #2 exactly as pin #1 1
1
or
Installation:
UNLOAD FIREARM. Place on a raised surface.
#1
INTERNAL LOCK HOLE
4
3 LASERLYTE
1
Moving Laser Dot
3
2
LASERLYTE
Windage right
LASERLYTE
Elevation up down
LYTE LASER
left
CK_AMF 9.indd 2
5/16/12 11:36 AM
®
LASERLYTE
®
• Fits Ruger® LC9 and Kel-Tec® PF9 • Quick and Easy installation • Works with most pocket holsters • Ergonomic activation • Dual laser modes with auto-off feature
LASERLYTE
5 min. 6 min. Off
5 min.
• • • •
®
After 5 minutes in any mode, warning mode pulse will activate. After 1 minute in warning pulse mode, laser will turn off. Press the switch during warning pulse for laser reset.
Batteries: 4-377 batteries Use Allen wrench .050 to remove battery cover Polarity marked on board inside of battery compartment. Note: Dimples on battery cover must be face down. Tighten down the battery cover and check periodically.
CK-AMF9 Patent Pending
Dimples Down
WARRANTY: One Year Limited Warranty.
®
DANGER LASER LIGHT AVOID DIRECT EYE EXPOSURE
POWER OUTPUT < 5mw WAVELENGTH 630-670mm CLASS IIIa PRODUCT
30 N. Alamos Drive - Cottonwood, AZ 86326 Phone 928-649-3201 - Fax 928-649-3970
®
www.LaserLyte.com
REV0512
CK_AMF 9.indd 1
5/16/12 11:36 AM
Kel-Tec®/Ruger® 9mm Side Mount Laser CK-AMF9
INTERNAL LOCK HOLE
LASERLYTE
Unload firearm.
Attach danger label to side of gun near laser with arrow pointing toward front sight.
1
Activation:
1 Press once turns laser on: constant or pulse 2 Press and hold for 5 seconds to change mode. 3 Second press turns laser off. ON/OFF
#1
Read instructions completely before installing your laser. Failure to do so may result in damage to your laser or firearm.
Attach danger label to side of gun near laser with arrow pointing toward front sight.
LASERLYTE
#2
#2
The two LaserLyte® frame pin screws are pre-loaded with a self-locking nylon patch. If you un-install the CK-AMF9, re-apply a self-locking material such as Lock-tite® Threadlocker Blue 242® to the LaserLyte® frame pin screws before re-installing the laser.
LASERLYTE
or LASERLYTE
Laser Sight In:
1 Use the provided .035 Allen wrench to adjust the sight. 2 Always end adjustments on a clockwise turn. 3 Make final adjustments at shooting range.
Do not block internal lock hole (N/A for Keltec®).
Use both .062 Allen wrenches to tighten screws until snug. Do not over tighten! Tighten down the battery cover, and check periodically.
3
LASERLYTE
5 sec.
2
3 Place laser on gun, align holes and insert screws. 4
2
LASERLYTE
1/4”
Using punch and small hammer, drift pin #1 out no more than 1/4”. Immediately insert LaserLyte® mounting pin and tap into place, completely replacing pin #1. 2 Follow the steps for pin #2 exactly as pin #1 1
1
or
Installation:
UNLOAD FIREARM. Place on a raised surface.
#1
INTERNAL LOCK HOLE
4
3 LASERLYTE
1
Moving Laser Dot
3
2
LASERLYTE
Windage right
LASERLYTE
Elevation up down
LYTE LASER
left
CK_AMF 9.indd 2
5/16/12 11:36 AM
