WOOD FOLDING ARM KIT Installation AWS
DoorKing Part Number
WOOD FOLDING ARM KIT
1601-384
This kit is designed for the 1600 model barrier gate operators only. Recommended for low headroom applications.
Kit Includes: Cable Attachment Assembly
4 Bolts with Locknuts (Small)
Bolt with Bushing and Locknut (Medium) Cable Clamp
Cable
Pre-Crimped Eyelet
Bolt with Brass Bushing and Locknut (Large)
Cable Eyelet
2 Wood Arms
Locking Turnbuckle
2 Hinge Plates
Installation
Cut Arms to Length
first for the height limitations.
Total Height
1 Cut this arm
Determining First Arm Length
Note: Completed folding arm assembly shown in the UP position to illustrate the total height.
Note: Completed folding arm assembly shown in the DOWN position to illustrate traffic lane width.
2 Cut this arm second for the traffic lane width. Note: Second arm can be a different size than the first.
Determining Second Arm Length Traffic Lane Width
120 Glasgow Avenue Inglewood, California 90301 U.S.A.
DoorKing Part Number
Installing Arms
1601-384
Installing Cable Attachment Assembly Remove stud from operator housing and assemble as shown.
o
Bolt Head (Inside Housing)
to ust
ar
cle
ub.
h
Washer (Inside Housing)
3A
H tor
ra
e Op
j Ad
Pre-Crimped Eyelet
g
in us
Inn
er
Installing Hinge Plates Bolt (Medium)
Arm
Turnbuckle
Bushing Locknut
Bolt (Large) Bushing 4 Bolts (Small)
Existing Stud Locknut Brass Bushing
Top View of Operator Housing
2A Ou
ter
Locknut
Arm
4 Locknuts 3A
Hub
3 Install cable. Cable MUST clear hub! Outer Arm 2A
1 Install inner arm on hub.
2 Install hinge plates.
Cut off excess cable. Cable Clamp
Allow turnbuckle to loosen or tighten.
Cable Eyelet MUST be installed in turnbuckle.
Adjusting and Locking Cable Assembly After adjusting cable tension, lock turnbuckle with nuts in position shown to prevent turnbuckle from rubbing against hinge plates when the arm is in the UP position.
Outer Arm
Inner Arm
Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely.
Side View of Operator Housing
1601-267-C-4-12
Important: Do not adjust cable too tight or it will bind.
Copyright 2012 DoorKing, Inc. All rights reserved.
120 Glasgow Avenue Inglewood, California 90301 U.S.A.
WOOD FOLDING ARM KIT
1601-384
This kit is designed for the 1600 model barrier gate operators only. Recommended for low headroom applications.
Kit Includes: Cable Attachment Assembly
4 Bolts with Locknuts (Small)
Bolt with Bushing and Locknut (Medium) Cable Clamp
Cable
Pre-Crimped Eyelet
Bolt with Brass Bushing and Locknut (Large)
Cable Eyelet
2 Wood Arms
Locking Turnbuckle
2 Hinge Plates
Installation
Cut Arms to Length
first for the height limitations.
Total Height
1 Cut this arm
Determining First Arm Length
Note: Completed folding arm assembly shown in the UP position to illustrate the total height.
Note: Completed folding arm assembly shown in the DOWN position to illustrate traffic lane width.
2 Cut this arm second for the traffic lane width. Note: Second arm can be a different size than the first.
Determining Second Arm Length Traffic Lane Width
120 Glasgow Avenue Inglewood, California 90301 U.S.A.
DoorKing Part Number
Installing Arms
1601-384
Installing Cable Attachment Assembly Remove stud from operator housing and assemble as shown.
o
Bolt Head (Inside Housing)
to ust
ar
cle
ub.
h
Washer (Inside Housing)
3A
H tor
ra
e Op
j Ad
Pre-Crimped Eyelet
g
in us
Inn
er
Installing Hinge Plates Bolt (Medium)
Arm
Turnbuckle
Bushing Locknut
Bolt (Large) Bushing 4 Bolts (Small)
Existing Stud Locknut Brass Bushing
Top View of Operator Housing
2A Ou
ter
Locknut
Arm
4 Locknuts 3A
Hub
3 Install cable. Cable MUST clear hub! Outer Arm 2A
1 Install inner arm on hub.
2 Install hinge plates.
Cut off excess cable. Cable Clamp
Allow turnbuckle to loosen or tighten.
Cable Eyelet MUST be installed in turnbuckle.
Adjusting and Locking Cable Assembly After adjusting cable tension, lock turnbuckle with nuts in position shown to prevent turnbuckle from rubbing against hinge plates when the arm is in the UP position.
Outer Arm
Inner Arm
Rotate arm up and down. Adjust cable tension with turnbuckle to level outer arm. Make sure that cable assembly is not binding or twisting and everything moves freely.
Side View of Operator Housing
1601-267-C-4-12
Important: Do not adjust cable too tight or it will bind.
Copyright 2012 DoorKing, Inc. All rights reserved.
120 Glasgow Avenue Inglewood, California 90301 U.S.A.
