zic360nhrh monogram36" built-in bottom-freezer refrigerator
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NHRH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHRH
FLUSH INSET INSTALLATION 26" (66.0) 20 5/8" (52.4)
38" (96.5)
11 1/2" (29.2)
* 84 1/2"
* 83 1/2" (212.1)
(214.6)
*73"
(185.4)
SPECIFICATIONS Overall Width
38" (96.5 cm)†
Overall Height
84 1/2" (214.6 cm)†
Overall Depth
26" (66.0 cm)†
Door Clearance
38 3/4" (98.4 cm)
Cutout Width
39" (99.1 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
*26 7/16" (67.1)
*4"
FRONT VIEW
(10.2)
*4"
(10.2)
SIDE VIEW
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84”
35" (89.0) Case width
Allow 15" (38.1) min clearance for 115˚ door swing
640 lb (290.3 kg)
† Dimensions include 3/4" custom cabinet panel
TOP VIEW
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
38 3/4" (98.4)
Allow 4" (10.2) min clearance to a wall for 90˚ door swing
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances. Product Specification Revised 1/18 ZIC360NHRH
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 3/4" PANELS
FLUSH INSET INSTALLATION
TOP VIEW 35 1/2" (90.2)
2 5/16"
Finished cleats (7.6) 1 Case Trim
(5.9)
Flush inset depth
10" (25.4) 20 15/16" (53.2)
1/2" (1.3)
39" (99.1) Flush inset width 37 1/2" (95.3)
3/4" (1.9)
Depth to cleat
*83 1/2" min *84 1/2" max
Width of side cleats
Width between cleats
(212.1-214.6) *Trim will overlap additional 7/16"
10"
75"
(25.4)
(190.5 ) From floor to bottom of electrical area
Finished cleats
A
6"
ELEC.
(15.2)
24 3/16" (61.4)
75 1/2"
84"
85"
WATER 3 1/2"
5" 3 1/2"
(9.0)
(12.7)
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
5"
(12.7)
10"(25.4)
(8.9)
7"
(17.8)
3 1/2" FRONT VIEW (8.9)
SIDE VIEW
7/16" (1.1) Trim overlap
(3.8)
3/4" Panel
(15.2)
26 3/16" (66.5)
NOTES
24" (61.0) 1/2"
Door
6"
ELEC.
Case
3"
5 1/4" (13.3)
B WATER 3 1/2" (9.0)
WATER 7" (17.8) 3 1/2"
SIDE VIEW
W
(8.9)
FRONT VIEW
ANTI-TIP BRACKET
FLUSH INSTALLATION 81 1/2" ZIC360NHLH_RH (207.0)
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.
CL
Use two additional hole locations at end of brackets
ZIC360NHRH
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A 38"
Fresh Food Panel
B
C
NOTES
D
10 11/16" 46 9/16" 22 7/16"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
C
D
Freezer Drawer Panel
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
3/4" RAISED DOOR PANEL ROUTING TOP
DETAIL TOP
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
ZIC360NHRH
7/16"
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Front
Back Back
Front
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16". Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM
DETAIL LEFT SIDE
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4" 3/32" 1/4"
2-1/16"
2-1/16" Front
LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" RAISED GRILL PANEL ROUTING DETAIL TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
ZIC360NHRH
FLUSH INSET INSTALLATION
TOP
NOTES
Front 1-11/16" ROUTER DEPTH 1/4"
Back Back
Front
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING DETAIL LEFT SIDE
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
3/16"
ROUTER DEPTH 1/4" 3/32"
BOTTOM
1/4"
DETAIL BOTTOM
2-1/16"
3/4" PANEL SIDE VIEW (AFTER ROUTING)
2-1/16"
Front LEFT SIDE Back
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
3/4" RAISED DRAWER PANEL ROUTING TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
RIGHT SIDE
DETAIL TOP
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Front
7/16"
Back Back
Front
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
DETAIL BOTTOM DETAIL LEFT SIDE
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16" Front
LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 1/2" PANELS
FLUSH INSET INSTALLATION
TOP VIEW
NOTES
Case
5 3/8" (13.7) 2 5/16"
Finished cleats Case Trim
3"
35 1/2" (90.2)
24" (61.0) Door 1 1/2"
(7.6)
(5.9)
1/2" Panel
26 3/16" (66.5) 6" Flush inset depth ELEC.
(15.2)
20 13/16" (52.9) Depth to cleat 10"
3/4" (1.9)
Width of side cleats
(25.4)
(3.8)
7/16" (1.1) Trim overlap
1/2" (1.3)
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
*83 1/2" min *84 1/2" max (212.1-214.6) *Trim will overlap additional 7/16"
10"
(25.4)
A
6"
ELEC.
(15.2)
24 3/16" (61.4)
75"
(190.5 ) From floor to bottom of electrical area
Finished cleats
85"
75 1/2"
84"
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
WATER 5"
(12.7)
3 1/2"
5" 3 1/2"
(9.0)
(8.9)
(12.7)
7"
(17.8)
3 1/2"
W
B10"(25.4) 7" WATER (17.8) 3 1/2" WATER (9.0)
3 1/2" (8.9)
SIDE VIEW FRONT VIEW
ANTI-TIP BRACKET CL
Use two FLUSH INSTALLATION additional hole locations at end of brackets ZIC360NHLH_RH
81 1/2" (207.0)
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit.
(8.9)
FRONT VIEW SIDE VIEW
ZIC360NHRH
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 1/2" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS A
B
1/4" Backer Panel
33 7/8"
8 7/8"
.10" Space Panel
32 1/2"
7 5/8" 44 11/16" 20 1/2"
38"
10 11/16" 46 9/16" 22 7/16"
B
Grille Panel
1/2" Overlay Panel
Fresh Food Panel
C
D
NOTES
46 1/16" 21 7/8"
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim. Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.
C
Freezer Drawer Panel
• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
D
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight – 25 lbs.
1/2" OVERLAY PANEL ROUTING DIMENSIONS
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
Grille Back
C
Door
A
1/2" Overlay Panel
B
D
C
ZIC360NHRH
Hinge Side
Door Panel Back
1/4" Backer Panel
.10" Spacer
Backer with Overlay Panel Assembly
PANEL DIMENSIONS A
A
C
A
D
B
B
C
D
Fresh Food Panel 2 1/16"
2 1/16"
5/16"
3/16"
Freezer Panel
2 1/16"
2 1/16"
5/16"
3/16"
Grille Panel
2 1/16"
2 1/16"
1 11/16"
3/16"
Freezer Drawer
D
B
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" OR 1/2" DUAL INSTALLATIONS 75" (190.5) Finished Width
4 5/16"
5 1/2"
ELEC. 9"
26 3/16" (66.5) Min. Cutout Depth
NOTES
5 1/2"
ELEC.
(13.9)
FLUSH INSET INSTALLATION
24 3/16" (61.4)
A
(10.9)
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims. A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.
(13.9)
9"
(22.9)
(22.9)
85"
(215.9) Finished Opening
75 1/2"
(191.8 ) From floor to bottom of electrical area
WATER 7"
WATER
3 1/2" (9.0)
3 1/2" (9.0)
7 1/2" 7 1/2"
(17.8)
(19.1)
7" 3 1/2"
(19.1)
(17.8)
(8.9)
3 1/2"
W
SIDE VIEW
FRONT VIEW 15" (38.1) min
15" (38.1) min
1"
To wall (2.5) FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION
To wall
A B
Grille Panel
115˚ Door swing
Fresh Food Panel
Fresh Food Panel
(8.9)
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier. ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
E
115˚ Door swing
ZIC360NHRH
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
C
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle. Freezer Drawer Panel
Freezer Drawer Panel
D
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
PANEL DIMENSIONS A
B
1/4" Backer Panel
69 7/8"
8 7/8"
46 1/16" 21 7/8"
C
D
33 7/8"
E
.10" Space Panel
68 1/2"
7 5/8" 44 11/16" 20 1/2"
32 1/2"
1/2" Overlay Panel
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
ZIC360NHLH_ZIC360NHRH
Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. • Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A
B
C
D
ZIC360NHRH
E
NOTES
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
E Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
Freezer Drawer Panel
C
D
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs
3/4" RAISED DOOR AND DRAWER PANEL ROUTING (SEE PAGE 5 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS) DETAIL TOP
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
7/16"
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Front
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Back
Back
Front
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
3/16"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM DETAIL HINGE SIDE
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
DETAIL HANDLE SIDE ROUTER DEPTH 1/4"
2 1/16"
3/16"
Front HINGE SIDE
HANDLE SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
WATER 3 1/2"
WATER 3 1/2"
7" 3 1/2" MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 7"
(9.0)
(17.8)
7 1/2" 7 1/2" (19.1)
(9.0)
(19.1)
(17.8)
(8.9)
3 1/2"
W
3/4" OR 1/2" DUAL PRODUCT FRONT VIEW CLEARANCES 15" (38.1) min
15" (38.1) min
1"
To wall
SIDE VIEW
ZIC360NHRH
(8.9)
FLUSH INSET INSTALLATION
To wall
(2.5)
NOTES
115˚ Door swing
115˚ Door swing
A I n a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2 custom panel unified grille kit for this installation.
A
ZIC360NHLH_ZIC360NHRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHRH
STANDARD INSTALLATION 25 1/4" (64.1) 25 1/4" (64.1) 23 7/8" (60.7) 23 7/8" (60.7)
36" (91.5) 36" (91.5) 1 7/8" 1 (4.8) 7/8"
9 7/8" 9(25.1) 7/8"
(4.8)
(25.1)
*84"
(213.4) *84" (213.4)
46 1/4" 46(117.5) 1/4"
*83 1/2" (212.1) *83 1/2"
(117.5)
(212.1)
*73 1/4" (186.1) *73 1/4" (186.1)
*26" (66.0) *26" (66.0) *24 1/8" (61.3) *24 1/8"
*26 1/2" (67.3) *26 1/2"
SPECIFICATIONS
(67.3)
Overall Width
36" (91.4 cm)
Overall Height
84" (213.4 cm)
Overall Depth
25 3/8" (64.5 cm)
Door Clearance
36 3/4" (93.4 cm)
Cutout Width
35 1/2" (90.2 cm)
Cutout Height
83 1/2" - 84 1/2" (212.1 - 214.6 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
640 lb (290.3 kg)
(61.3)
FRONT VIEW FRONTlegs VIEW * Shipping height. Use leveling and wheels for maximum
(9.2)
SIDE VIEW SIDE VIEW
* 1" Shipping Use leveling legs and wheels for maximum height height. adjustment from shipping height. 1" height adjustment from shipping height.
35" (89.0) Case 35" width (89.0) Case width ** Allow 25" (63.5) min 130˚min ** clearance Allow 25"for (63.5) door swingfor 130˚ clearance door swing
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
*3 5/8" *3(9.2) 5/8"
36 3/4" 36(93.4) 3/4"
TOP VIEW TOP VIEW
(93.4)
** Allow 4" (10.2) min to a wall ** clearance Allow 4" (10.2) min for 90˚ door clearance toswing a wall for The 90˚ door swing stop. factory-set
** These refrigerators are equipped with a 2-position door 130° door ** These are to equipped with a 2-position doorcabinets stop. The 130° door swing refrigerators can be adjusted 90° if clearances to adjacent orfactory-set walls is restricted. Allow **These are to equipped 3-position door stop. The swing can be adjusted 90° if clearances to adjacent cabinets orstop walls isfactory-set restricted. Allow a 15"refrigerators minimum clearance to wall forwith pan aremoval. If the 90° door position is used, pan 130° door can be 90° or 130°Iffor installation a 15" minimum clearance to wall fortopan removal. thestandard 90° door stop position isifused, pan access isswing maintained, butadjusted pan removal is restricted. clearances adjacentbut cabinets or walls is restricted. Allow a 15" minimum access is to maintained, pan removal is restricted. clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances. Product Specification Revised 1/18
ZIC360NXRH ZIC360NXRH
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD INSTALLATION
STANDARD INSTALLATION 3"
35 1/2" (90.2)
2 5/16"
24" (61.0)
(7.6)
3 1/8"
(3.8)
6"
(3.97)
7/16" (1.1) Trim overlap
35 1/2" (90.2)
2 5/16"
A
(5.874)
*83 1/2" min *84 1/2" max
ELEC.
(212.1-214.6) *Trim will overlap additional 7/16"
6"
(15.24)
WARNING:
10"
(25.4)
75"
(190.5 ) From floor to bottom of electrical area
75"
*84 1/2"
(190.5 ) From floor to bottom of electrical area
(214.6) *Trim will overlap additional 7/16"
WATER 5"
3 1/2"
(12.7)
5" 3 1/2"
(9.0)
(12.7)
B 10"(25.4)
(8.9)
WATER 3 1/2"WATER (9.0) 5" 3 1/2"
5"
(12.7)
3 1/2"
FRONT W VIEW
(8.9)
(12.7)
(8.9)
SIDE VIEW
FRONT VIEW
SIDE VIEW
ANTI-TIP BRACKET CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
Wall Studs
(207.0)
NOTES A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area.
(15.2)
24" (61) 10" 1 9/16" (25.4)
(7.93)
7/16" (1.1) Trim overlap
TOP VIEW 1 1/2"
(5.9)
ELEC.
ZIC360NHRH
STANDARD INSTALLATION ZIC360NHLH_RH
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION PANEL ASSEMBLY CROSS SECTION
A Grille Panel
B
1/4" Framed Panel
Supplied Handles
STANDARD INSTALLATION NOTES
Trim
Door
ZIC360NHRH
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels:
Fresh Food Panel
For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
C
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
Freezer Drawer Panel
D
PANEL DIMENSIONS A 1/4" Framed Panel
B
C
D
33 7/8" 8 7/8" 46 1/16" 21 7/8"
3/4" Overlay Panels: The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION PANEL ASSEMBLY CROSS SECTION A Grille Panel
B
Trim
Door
1/4" Backer Panel
3/4" Overlay Panel
.10" Spacer Panel
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
Supplied Handles
Fresh Food Panel
C
PANEL DIMENSIONS
A
Freezer Drawer Panel
D
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
B
C
D
1/4" Backer Panel
33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Spacer Panel
32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel
34 1/8"
9"
46 5/16"
.25" + .10" + .75" = 1.10" Total Panel Thickness
22"
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR CUSTOM SIDE PANELS F
ZIC360NHRH
STANDARD INSTALLATION
24" (61.0)
NOTES
3/16" (.5)
1 7/8" (4.8)
*84"
(213.4) *Depending on installation height
F S ide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
*3"- 4"
(7.6 - 10.2) *Depending on installation height
2 9/16" (6.5)
XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR DUAL INSTALLATIONS
STANDARD INSTALLATION
A
71 1/2" (181.6) Finished Width
2 5/16" 6"
10"
(15.2)
Additional cutout width may be required when side panels are used.
10"
(25.4)
NOTES A A separate 115V, 60Hz, 15- or 20amp power supply is recommended for each product.
6"
ELEC.
(15.2)
24" (60.9) Min. Cutout Depth
24 3/16" (61.4)
(5.9)
ELEC.
ZIC360NHRH
(25.4)
83 1/2" min 84 1/2" max
(212.1-214.6) Finished Opening
75"
(190.5 ) From floor to bottom of electrical area
WATER 3 1/2" (9.0)
5"
(12.7)
WATER 5 3/4" 5 3/4" (14.6)
3 1/2" (9.0)
(14.6)
5" 3 1/2"
(12.7)
10" (25.4)
(8.9)
WATER
SIDE VIEW
FRONT VIEW 25" min
25" min
1"
(63.5)
(63.5)
(2.5) To wall To wall STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
A
130˚ Door swing
Fresh Food Panel
Freezer Drawer Panel
PANEL ASSEMBLY CROSS SECTION
1/4" Framed Panel
B
Grille Panel
E
130˚ Door swing
Fresh Food Panel
C
Freezer Drawer Panel
A
69 7/8"
B
8 7/8"
C
46 1/16"
D
21 7/8"
E
33 7/8"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs.
D
Order ZUG2: Unified grille kit for dual installation Door
Supplied Handles
Trim
1/4" Framed Panel
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH ZICS360NXLH_ZICS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION PANEL DIMENSIONS A .10" 3/4" Spacer Overlay Panel Panel
NOTES
A
69 7/8"
68 1/2"
70 1/8"
E
B
8 7/8"
7 5/8"
9"
71 1/2" Fresh(181.6)
C
The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
Finished Width
Food Panel
6"
ELEC.
STANDARD INSTALLATION
1/4" Backer Panel
B
Grille Panel
Fresh 2 5/16"Food (5.9) Panel
24 3/16" C (61.4)
ELEC.
(15.2)
10"
6"
D
46 1/16" 44 11/16" 46 24"5/16" (60.9) Min. 21 7/8" 20 1/2" Cutout 22"Depth
E
33 7/8"
32 1/2"
34 1/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
(15.2)
10"
(25.4)
(25.4)
83 1/2" min 84 1/2" max
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs.
(212.1-214.6) Finished Opening
PANEL ASSEMBLY CROSS SECTION
75"
Order ZUG2: Unified grille kit for dual installation
(190.5 ) Trim From floor to bottom 1/4" Backer Panel of electrical area
Door 3/4" Overlay Panel
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
.10" Spacer Panel
Supplied Handles
WATER 5"
3 1/2" (9.0)
(12.7)
WATER 5 3/4" 5 3/4" (14.6)
3 1/2" (9.0)
(14.6)
5" 3 1/2"
(12.7)
(8.9)
10" (25.4)
WATER
DUAL PRODUCT CLEARANCES A
25" min
25" min
1"
(63.5) To wall
SIDE VIEW
FRONT VIEW (63.5) To wall
(2.5)
3/4" Overlay Panels:
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
D
Freezer Drawer Panel
Freezer Drawer Panel
ZIC360NHRH
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16". A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2: custom panel unified grille kit for one continuous grille panel.
130˚ Door swing
130˚ Door swing
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NHRH
FEATURES AND BENEFITS CUSTOM APPEARANCE Allows personalization with cabinet-compatible panels an custom handles UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Allows precise temperature settings and are positioned for maximum ease of use HUMIDITY CONTROLLED VEGETABLE COMPARTMENTS AND SEALED SNACK PANS Help maintain freshness and help preserve foods longer ADJUSTABLE, SPILL PROOF GLASS SHELVES Make it easy to customize storage to handle foods and containers of various sizes 2 SEALED DELI PANS WITH FULL-EXTENSION SLIDES SIX ADJUSTABLE DOOR BINS Offer added storage flexibility GE WATER™ FILTRATION SYSTEM Delivers clean, great tasting ice
R
Product Specification Revised 1/18
ZIC360NHRH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHRH
FLUSH INSET INSTALLATION 26" (66.0) 20 5/8" (52.4)
38" (96.5)
11 1/2" (29.2)
* 84 1/2"
* 83 1/2" (212.1)
(214.6)
*73"
(185.4)
SPECIFICATIONS Overall Width
38" (96.5 cm)†
Overall Height
84 1/2" (214.6 cm)†
Overall Depth
26" (66.0 cm)†
Door Clearance
38 3/4" (98.4 cm)
Cutout Width
39" (99.1 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
*26 7/16" (67.1)
*4"
FRONT VIEW
(10.2)
*4"
(10.2)
SIDE VIEW
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84”
35" (89.0) Case width
Allow 15" (38.1) min clearance for 115˚ door swing
640 lb (290.3 kg)
† Dimensions include 3/4" custom cabinet panel
TOP VIEW
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
38 3/4" (98.4)
Allow 4" (10.2) min clearance to a wall for 90˚ door swing
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances. Product Specification Revised 1/18 ZIC360NHRH
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 3/4" PANELS
FLUSH INSET INSTALLATION
TOP VIEW 35 1/2" (90.2)
2 5/16"
Finished cleats (7.6) 1 Case Trim
(5.9)
Flush inset depth
10" (25.4) 20 15/16" (53.2)
1/2" (1.3)
39" (99.1) Flush inset width 37 1/2" (95.3)
3/4" (1.9)
Depth to cleat
*83 1/2" min *84 1/2" max
Width of side cleats
Width between cleats
(212.1-214.6) *Trim will overlap additional 7/16"
10"
75"
(25.4)
(190.5 ) From floor to bottom of electrical area
Finished cleats
A
6"
ELEC.
(15.2)
24 3/16" (61.4)
75 1/2"
84"
85"
WATER 3 1/2"
5" 3 1/2"
(9.0)
(12.7)
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
5"
(12.7)
10"(25.4)
(8.9)
7"
(17.8)
3 1/2" FRONT VIEW (8.9)
SIDE VIEW
7/16" (1.1) Trim overlap
(3.8)
3/4" Panel
(15.2)
26 3/16" (66.5)
NOTES
24" (61.0) 1/2"
Door
6"
ELEC.
Case
3"
5 1/4" (13.3)
B WATER 3 1/2" (9.0)
WATER 7" (17.8) 3 1/2"
SIDE VIEW
W
(8.9)
FRONT VIEW
ANTI-TIP BRACKET
FLUSH INSTALLATION 81 1/2" ZIC360NHLH_RH (207.0)
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.
CL
Use two additional hole locations at end of brackets
ZIC360NHRH
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A 38"
Fresh Food Panel
B
C
NOTES
D
10 11/16" 46 9/16" 22 7/16"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
C
D
Freezer Drawer Panel
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
3/4" RAISED DOOR PANEL ROUTING TOP
DETAIL TOP
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
ZIC360NHRH
7/16"
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Front
Back Back
Front
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16". Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM
DETAIL LEFT SIDE
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4" 3/32" 1/4"
2-1/16"
2-1/16" Front
LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" RAISED GRILL PANEL ROUTING DETAIL TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
ZIC360NHRH
FLUSH INSET INSTALLATION
TOP
NOTES
Front 1-11/16" ROUTER DEPTH 1/4"
Back Back
Front
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING DETAIL LEFT SIDE
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
3/16"
ROUTER DEPTH 1/4" 3/32"
BOTTOM
1/4"
DETAIL BOTTOM
2-1/16"
3/4" PANEL SIDE VIEW (AFTER ROUTING)
2-1/16"
Front LEFT SIDE Back
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
3/4" RAISED DRAWER PANEL ROUTING TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
RIGHT SIDE
DETAIL TOP
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Front
7/16"
Back Back
Front
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
DETAIL BOTTOM DETAIL LEFT SIDE
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16" Front
LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 1/2" PANELS
FLUSH INSET INSTALLATION
TOP VIEW
NOTES
Case
5 3/8" (13.7) 2 5/16"
Finished cleats Case Trim
3"
35 1/2" (90.2)
24" (61.0) Door 1 1/2"
(7.6)
(5.9)
1/2" Panel
26 3/16" (66.5) 6" Flush inset depth ELEC.
(15.2)
20 13/16" (52.9) Depth to cleat 10"
3/4" (1.9)
Width of side cleats
(25.4)
(3.8)
7/16" (1.1) Trim overlap
1/2" (1.3)
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
*83 1/2" min *84 1/2" max (212.1-214.6) *Trim will overlap additional 7/16"
10"
(25.4)
A
6"
ELEC.
(15.2)
24 3/16" (61.4)
75"
(190.5 ) From floor to bottom of electrical area
Finished cleats
85"
75 1/2"
84"
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
WATER 5"
(12.7)
3 1/2"
5" 3 1/2"
(9.0)
(8.9)
(12.7)
7"
(17.8)
3 1/2"
W
B10"(25.4) 7" WATER (17.8) 3 1/2" WATER (9.0)
3 1/2" (8.9)
SIDE VIEW FRONT VIEW
ANTI-TIP BRACKET CL
Use two FLUSH INSTALLATION additional hole locations at end of brackets ZIC360NHLH_RH
81 1/2" (207.0)
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit.
(8.9)
FRONT VIEW SIDE VIEW
ZIC360NHRH
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 1/2" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS A
B
1/4" Backer Panel
33 7/8"
8 7/8"
.10" Space Panel
32 1/2"
7 5/8" 44 11/16" 20 1/2"
38"
10 11/16" 46 9/16" 22 7/16"
B
Grille Panel
1/2" Overlay Panel
Fresh Food Panel
C
D
NOTES
46 1/16" 21 7/8"
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim. Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.
C
Freezer Drawer Panel
• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
D
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight – 25 lbs.
1/2" OVERLAY PANEL ROUTING DIMENSIONS
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
Grille Back
C
Door
A
1/2" Overlay Panel
B
D
C
ZIC360NHRH
Hinge Side
Door Panel Back
1/4" Backer Panel
.10" Spacer
Backer with Overlay Panel Assembly
PANEL DIMENSIONS A
A
C
A
D
B
B
C
D
Fresh Food Panel 2 1/16"
2 1/16"
5/16"
3/16"
Freezer Panel
2 1/16"
2 1/16"
5/16"
3/16"
Grille Panel
2 1/16"
2 1/16"
1 11/16"
3/16"
Freezer Drawer
D
B
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" OR 1/2" DUAL INSTALLATIONS 75" (190.5) Finished Width
4 5/16"
5 1/2"
ELEC. 9"
26 3/16" (66.5) Min. Cutout Depth
NOTES
5 1/2"
ELEC.
(13.9)
FLUSH INSET INSTALLATION
24 3/16" (61.4)
A
(10.9)
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims. A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.
(13.9)
9"
(22.9)
(22.9)
85"
(215.9) Finished Opening
75 1/2"
(191.8 ) From floor to bottom of electrical area
WATER 7"
WATER
3 1/2" (9.0)
3 1/2" (9.0)
7 1/2" 7 1/2"
(17.8)
(19.1)
7" 3 1/2"
(19.1)
(17.8)
(8.9)
3 1/2"
W
SIDE VIEW
FRONT VIEW 15" (38.1) min
15" (38.1) min
1"
To wall (2.5) FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION
To wall
A B
Grille Panel
115˚ Door swing
Fresh Food Panel
Fresh Food Panel
(8.9)
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier. ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
E
115˚ Door swing
ZIC360NHRH
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
C
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle. Freezer Drawer Panel
Freezer Drawer Panel
D
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
PANEL DIMENSIONS A
B
1/4" Backer Panel
69 7/8"
8 7/8"
46 1/16" 21 7/8"
C
D
33 7/8"
E
.10" Space Panel
68 1/2"
7 5/8" 44 11/16" 20 1/2"
32 1/2"
1/2" Overlay Panel
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
ZIC360NHLH_ZIC360NHRH
Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. • Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A
B
C
D
ZIC360NHRH
E
NOTES
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
E Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
Freezer Drawer Panel
C
D
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs
3/4" RAISED DOOR AND DRAWER PANEL ROUTING (SEE PAGE 5 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS) DETAIL TOP
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
7/16"
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Front
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Back
Back
Front
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
3/16"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM DETAIL HINGE SIDE
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
DETAIL HANDLE SIDE ROUTER DEPTH 1/4"
2 1/16"
3/16"
Front HINGE SIDE
HANDLE SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
WATER 3 1/2"
WATER 3 1/2"
7" 3 1/2" MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 7"
(9.0)
(17.8)
7 1/2" 7 1/2" (19.1)
(9.0)
(19.1)
(17.8)
(8.9)
3 1/2"
W
3/4" OR 1/2" DUAL PRODUCT FRONT VIEW CLEARANCES 15" (38.1) min
15" (38.1) min
1"
To wall
SIDE VIEW
ZIC360NHRH
(8.9)
FLUSH INSET INSTALLATION
To wall
(2.5)
NOTES
115˚ Door swing
115˚ Door swing
A I n a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2 custom panel unified grille kit for this installation.
A
ZIC360NHLH_ZIC360NHRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHRH
STANDARD INSTALLATION 25 1/4" (64.1) 25 1/4" (64.1) 23 7/8" (60.7) 23 7/8" (60.7)
36" (91.5) 36" (91.5) 1 7/8" 1 (4.8) 7/8"
9 7/8" 9(25.1) 7/8"
(4.8)
(25.1)
*84"
(213.4) *84" (213.4)
46 1/4" 46(117.5) 1/4"
*83 1/2" (212.1) *83 1/2"
(117.5)
(212.1)
*73 1/4" (186.1) *73 1/4" (186.1)
*26" (66.0) *26" (66.0) *24 1/8" (61.3) *24 1/8"
*26 1/2" (67.3) *26 1/2"
SPECIFICATIONS
(67.3)
Overall Width
36" (91.4 cm)
Overall Height
84" (213.4 cm)
Overall Depth
25 3/8" (64.5 cm)
Door Clearance
36 3/4" (93.4 cm)
Cutout Width
35 1/2" (90.2 cm)
Cutout Height
83 1/2" - 84 1/2" (212.1 - 214.6 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
640 lb (290.3 kg)
(61.3)
FRONT VIEW FRONTlegs VIEW * Shipping height. Use leveling and wheels for maximum
(9.2)
SIDE VIEW SIDE VIEW
* 1" Shipping Use leveling legs and wheels for maximum height height. adjustment from shipping height. 1" height adjustment from shipping height.
35" (89.0) Case 35" width (89.0) Case width ** Allow 25" (63.5) min 130˚min ** clearance Allow 25"for (63.5) door swingfor 130˚ clearance door swing
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
*3 5/8" *3(9.2) 5/8"
36 3/4" 36(93.4) 3/4"
TOP VIEW TOP VIEW
(93.4)
** Allow 4" (10.2) min to a wall ** clearance Allow 4" (10.2) min for 90˚ door clearance toswing a wall for The 90˚ door swing stop. factory-set
** These refrigerators are equipped with a 2-position door 130° door ** These are to equipped with a 2-position doorcabinets stop. The 130° door swing refrigerators can be adjusted 90° if clearances to adjacent orfactory-set walls is restricted. Allow **These are to equipped 3-position door stop. The swing can be adjusted 90° if clearances to adjacent cabinets orstop walls isfactory-set restricted. Allow a 15"refrigerators minimum clearance to wall forwith pan aremoval. If the 90° door position is used, pan 130° door can be 90° or 130°Iffor installation a 15" minimum clearance to wall fortopan removal. thestandard 90° door stop position isifused, pan access isswing maintained, butadjusted pan removal is restricted. clearances adjacentbut cabinets or walls is restricted. Allow a 15" minimum access is to maintained, pan removal is restricted. clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted. Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances. Product Specification Revised 1/18
ZIC360NXRH ZIC360NXRH
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD INSTALLATION
STANDARD INSTALLATION 3"
35 1/2" (90.2)
2 5/16"
24" (61.0)
(7.6)
3 1/8"
(3.8)
6"
(3.97)
7/16" (1.1) Trim overlap
35 1/2" (90.2)
2 5/16"
A
(5.874)
*83 1/2" min *84 1/2" max
ELEC.
(212.1-214.6) *Trim will overlap additional 7/16"
6"
(15.24)
WARNING:
10"
(25.4)
75"
(190.5 ) From floor to bottom of electrical area
75"
*84 1/2"
(190.5 ) From floor to bottom of electrical area
(214.6) *Trim will overlap additional 7/16"
WATER 5"
3 1/2"
(12.7)
5" 3 1/2"
(9.0)
(12.7)
B 10"(25.4)
(8.9)
WATER 3 1/2"WATER (9.0) 5" 3 1/2"
5"
(12.7)
3 1/2"
FRONT W VIEW
(8.9)
(12.7)
(8.9)
SIDE VIEW
FRONT VIEW
SIDE VIEW
ANTI-TIP BRACKET CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
Wall Studs
(207.0)
NOTES A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area.
(15.2)
24" (61) 10" 1 9/16" (25.4)
(7.93)
7/16" (1.1) Trim overlap
TOP VIEW 1 1/2"
(5.9)
ELEC.
ZIC360NHRH
STANDARD INSTALLATION ZIC360NHLH_RH
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION PANEL ASSEMBLY CROSS SECTION
A Grille Panel
B
1/4" Framed Panel
Supplied Handles
STANDARD INSTALLATION NOTES
Trim
Door
ZIC360NHRH
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels:
Fresh Food Panel
For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
C
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
Freezer Drawer Panel
D
PANEL DIMENSIONS A 1/4" Framed Panel
B
C
D
33 7/8" 8 7/8" 46 1/16" 21 7/8"
3/4" Overlay Panels: The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION PANEL ASSEMBLY CROSS SECTION A Grille Panel
B
Trim
Door
1/4" Backer Panel
3/4" Overlay Panel
.10" Spacer Panel
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
Supplied Handles
Fresh Food Panel
C
PANEL DIMENSIONS
A
Freezer Drawer Panel
D
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
B
C
D
1/4" Backer Panel
33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Spacer Panel
32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel
34 1/8"
9"
46 5/16"
.25" + .10" + .75" = 1.10" Total Panel Thickness
22"
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR CUSTOM SIDE PANELS F
ZIC360NHRH
STANDARD INSTALLATION
24" (61.0)
NOTES
3/16" (.5)
1 7/8" (4.8)
*84"
(213.4) *Depending on installation height
F S ide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
*3"- 4"
(7.6 - 10.2) *Depending on installation height
2 9/16" (6.5)
XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR DUAL INSTALLATIONS
STANDARD INSTALLATION
A
71 1/2" (181.6) Finished Width
2 5/16" 6"
10"
(15.2)
Additional cutout width may be required when side panels are used.
10"
(25.4)
NOTES A A separate 115V, 60Hz, 15- or 20amp power supply is recommended for each product.
6"
ELEC.
(15.2)
24" (60.9) Min. Cutout Depth
24 3/16" (61.4)
(5.9)
ELEC.
ZIC360NHRH
(25.4)
83 1/2" min 84 1/2" max
(212.1-214.6) Finished Opening
75"
(190.5 ) From floor to bottom of electrical area
WATER 3 1/2" (9.0)
5"
(12.7)
WATER 5 3/4" 5 3/4" (14.6)
3 1/2" (9.0)
(14.6)
5" 3 1/2"
(12.7)
10" (25.4)
(8.9)
WATER
SIDE VIEW
FRONT VIEW 25" min
25" min
1"
(63.5)
(63.5)
(2.5) To wall To wall STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
A
130˚ Door swing
Fresh Food Panel
Freezer Drawer Panel
PANEL ASSEMBLY CROSS SECTION
1/4" Framed Panel
B
Grille Panel
E
130˚ Door swing
Fresh Food Panel
C
Freezer Drawer Panel
A
69 7/8"
B
8 7/8"
C
46 1/16"
D
21 7/8"
E
33 7/8"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs.
D
Order ZUG2: Unified grille kit for dual installation Door
Supplied Handles
Trim
1/4" Framed Panel
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH ZICS360NXLH_ZICS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION PANEL DIMENSIONS A .10" 3/4" Spacer Overlay Panel Panel
NOTES
A
69 7/8"
68 1/2"
70 1/8"
E
B
8 7/8"
7 5/8"
9"
71 1/2" Fresh(181.6)
C
The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
Finished Width
Food Panel
6"
ELEC.
STANDARD INSTALLATION
1/4" Backer Panel
B
Grille Panel
Fresh 2 5/16"Food (5.9) Panel
24 3/16" C (61.4)
ELEC.
(15.2)
10"
6"
D
46 1/16" 44 11/16" 46 24"5/16" (60.9) Min. 21 7/8" 20 1/2" Cutout 22"Depth
E
33 7/8"
32 1/2"
34 1/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
(15.2)
10"
(25.4)
(25.4)
83 1/2" min 84 1/2" max
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs.
(212.1-214.6) Finished Opening
PANEL ASSEMBLY CROSS SECTION
75"
Order ZUG2: Unified grille kit for dual installation
(190.5 ) Trim From floor to bottom 1/4" Backer Panel of electrical area
Door 3/4" Overlay Panel
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
.10" Spacer Panel
Supplied Handles
WATER 5"
3 1/2" (9.0)
(12.7)
WATER 5 3/4" 5 3/4" (14.6)
3 1/2" (9.0)
(14.6)
5" 3 1/2"
(12.7)
(8.9)
10" (25.4)
WATER
DUAL PRODUCT CLEARANCES A
25" min
25" min
1"
(63.5) To wall
SIDE VIEW
FRONT VIEW (63.5) To wall
(2.5)
3/4" Overlay Panels:
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
D
Freezer Drawer Panel
Freezer Drawer Panel
ZIC360NHRH
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16". A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2: custom panel unified grille kit for one continuous grille panel.
130˚ Door swing
130˚ Door swing
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NHRH
FEATURES AND BENEFITS CUSTOM APPEARANCE Allows personalization with cabinet-compatible panels an custom handles UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Allows precise temperature settings and are positioned for maximum ease of use HUMIDITY CONTROLLED VEGETABLE COMPARTMENTS AND SEALED SNACK PANS Help maintain freshness and help preserve foods longer ADJUSTABLE, SPILL PROOF GLASS SHELVES Make it easy to customize storage to handle foods and containers of various sizes 2 SEALED DELI PANS WITH FULL-EXTENSION SLIDES SIX ADJUSTABLE DOOR BINS Offer added storage flexibility GE WATER™ FILTRATION SYSTEM Delivers clean, great tasting ice
R
Product Specification Revised 1/18
