13 11 26
AUTHORIZED AUSTRALIAN DISTRIBUTORS
CAMPBELLS WHOLESALE PTY LTD 21 BALLANTYNE RD KEWDALE WA 6105 Tel.: (08) 9353 3354 Fax: (08) 9353 6994 www.campbellswholesale.com.au
EMERGENCY PHONE NO. (24 HOURS AUSTRALIA)
13 11 26 POISONS INFORMATION CENTRE Campbells Wholesale Pty Ltd makes no representation as to the completeness and accuracy of the data contained in this data sheet. It is the user’s obligation to evaluate and use this product safely and to comply with all the Local, State and Federal regulations and laws. Campbells Wholesale shall not be responsible for loss, damage or injury resulting from reliance upon or failure to adhere to any recommendations or information contained herein, from abnormal use of the material or from any hazard inherent in the nature of the material.
VITAL TECHNICAL SDN. BHD. Technical Data Sheet
VT-620/VT-620S
Issued Date:
14/02/11
Revision No.:
7
Revised Date:
27/12/11
Page:
1 Of 2
LM MS Sealant
Product Specification: Curing System Skin over time Elongation at break (ASTM D412) Shore A Hardness (ASTM C661) Density Application Temperature Service Temperature Packaging Features
Shelf Life
Moisture Curing 45 minutes 800% 25 – 35 (Approx) 1.55 – 1.57 g/ml 5°C to 40°C -30°C to 100°C 290ml Good UV Resistance Paintable Non-Staining Primerless Bonding to Most Substrates Anti Fungus / Mildew Resistance 9 months
Product Description: A one component, high performance sealant based on advance MS Polymer Technology. It is Solvent, Silicone and Isocyanates Free and Non-staining for natural stones applications. It has an excellent UV, weather and temperature resistance. It has excellent adhesion over a wide variety of substrates and is paintable with most common industrial paints.
Applications: Ideal for connection and expansion joints in building. Top sealing in glazing systems especially in combination with emulsion paints. It may be used without primer, to seal assemblies of glasses, glazed surfaces, porcelain, coated metal, epoxy and polyester panels, polystyrene, uPVC, stainless steel, anodized aluminum and finish wood.
Direction: • Surfaces must be clean, dry and free of dirt, grease, oil or water. • For a neat finish, apply masking tape and remove it before sealant has skinned over. • Cut tip off and puncture the internal foil seal with nozzle. Cut nozzle at 45° angle to desire bead-width and apply to substrate with cartridge gun. • Tooling time is 10 minutes, tack free time is 20 minutes. • Uncured sealant can be cleaned up with mineral spirits. • Use approved backing material for joints over 10mm deep.
VITAL TECHNICAL SDN. BHD. Technical Data Sheet
VT-620/VT-620S
Issued Date:
14/02/11
Revision No.:
7
Revised Date:
27/12/11
Page:
2 Of 2
LM MS Sealant
Limitation: The LM MS Sealant should not be: • Used for areas subject to continuous chlorinated water emersion, such as swimming pools, spas etc. • Constant immersed in salt water. • Used for PE, PP, Teflon, Neoprene and bituminous surfaces. • Used for glazing applications. • Paintable with alkyd resin paint because curing inhibition of the paint. • Used in trafficable joints greater than 10mm width
Caution: • • • •
Uncured adhesive / sealant causes skin and eyes irritation upon contact. Avoid contact with eyes, skin and mouth. In case of contact with eyes, flush with water immediately for 15 minutes. If irritation persists, seek medical attention. Keep out of reach of children. Use in well ventilated areas.
Storage • •
Store in a dry and cool place with temperature below +25°C. Use within 9 months from date of production.
Every endeavour has been made to ensure that the information given herein is true and reliable but it is given only for the guidance of our customers. The company cannot accept any responsibility for the loss or damage that may result from the use of the information, due to the possibility of various of processing or working conditions and of workmanship outside our control. Users are advised to confirm suitability of this product by their own tests.
CAMPBELLS WHOLESALE PTY LTD 21 BALLANTYNE RD KEWDALE WA 6105 Tel.: (08) 9353 3354 Fax: (08) 9353 6994 www.campbellswholesale.com.au
EMERGENCY PHONE NO. (24 HOURS AUSTRALIA)
13 11 26 POISONS INFORMATION CENTRE Campbells Wholesale Pty Ltd makes no representation as to the completeness and accuracy of the data contained in this data sheet. It is the user’s obligation to evaluate and use this product safely and to comply with all the Local, State and Federal regulations and laws. Campbells Wholesale shall not be responsible for loss, damage or injury resulting from reliance upon or failure to adhere to any recommendations or information contained herein, from abnormal use of the material or from any hazard inherent in the nature of the material.
VITAL TECHNICAL SDN. BHD. Technical Data Sheet
VT-620/VT-620S
Issued Date:
14/02/11
Revision No.:
7
Revised Date:
27/12/11
Page:
1 Of 2
LM MS Sealant
Product Specification: Curing System Skin over time Elongation at break (ASTM D412) Shore A Hardness (ASTM C661) Density Application Temperature Service Temperature Packaging Features
Shelf Life
Moisture Curing 45 minutes 800% 25 – 35 (Approx) 1.55 – 1.57 g/ml 5°C to 40°C -30°C to 100°C 290ml Good UV Resistance Paintable Non-Staining Primerless Bonding to Most Substrates Anti Fungus / Mildew Resistance 9 months
Product Description: A one component, high performance sealant based on advance MS Polymer Technology. It is Solvent, Silicone and Isocyanates Free and Non-staining for natural stones applications. It has an excellent UV, weather and temperature resistance. It has excellent adhesion over a wide variety of substrates and is paintable with most common industrial paints.
Applications: Ideal for connection and expansion joints in building. Top sealing in glazing systems especially in combination with emulsion paints. It may be used without primer, to seal assemblies of glasses, glazed surfaces, porcelain, coated metal, epoxy and polyester panels, polystyrene, uPVC, stainless steel, anodized aluminum and finish wood.
Direction: • Surfaces must be clean, dry and free of dirt, grease, oil or water. • For a neat finish, apply masking tape and remove it before sealant has skinned over. • Cut tip off and puncture the internal foil seal with nozzle. Cut nozzle at 45° angle to desire bead-width and apply to substrate with cartridge gun. • Tooling time is 10 minutes, tack free time is 20 minutes. • Uncured sealant can be cleaned up with mineral spirits. • Use approved backing material for joints over 10mm deep.
VITAL TECHNICAL SDN. BHD. Technical Data Sheet
VT-620/VT-620S
Issued Date:
14/02/11
Revision No.:
7
Revised Date:
27/12/11
Page:
2 Of 2
LM MS Sealant
Limitation: The LM MS Sealant should not be: • Used for areas subject to continuous chlorinated water emersion, such as swimming pools, spas etc. • Constant immersed in salt water. • Used for PE, PP, Teflon, Neoprene and bituminous surfaces. • Used for glazing applications. • Paintable with alkyd resin paint because curing inhibition of the paint. • Used in trafficable joints greater than 10mm width
Caution: • • • •
Uncured adhesive / sealant causes skin and eyes irritation upon contact. Avoid contact with eyes, skin and mouth. In case of contact with eyes, flush with water immediately for 15 minutes. If irritation persists, seek medical attention. Keep out of reach of children. Use in well ventilated areas.
Storage • •
Store in a dry and cool place with temperature below +25°C. Use within 9 months from date of production.
Every endeavour has been made to ensure that the information given herein is true and reliable but it is given only for the guidance of our customers. The company cannot accept any responsibility for the loss or damage that may result from the use of the information, due to the possibility of various of processing or working conditions and of workmanship outside our control. Users are advised to confirm suitability of this product by their own tests.
