2015 11 4 13 26 32 866
ES101
Product Care
Thermostatic Bar Mixer with Fixed Head ANGEL SHOWER
Ⅴ
148. 5mm 5 7/ 8" 71.5- 76. 5mm 2 13/16"-3"
15 0±2 5m m 5 7 / 8 " ±1"
Off On
2- Ø60mm 2-Ø2 3/ 8" 2 - G1 / 2B Ø39mm Ø1 9/ 16"
32.5mm 1 1/ 4"
Dear Customer, We want to ensure that you get long-lasting satisfaction and pleasure from your fitting. Installation Therefore, please read the following care Flush piping system prior and after instructions because damage to the surface installation of fitting thoroughly and underlying material resulting from improper (consider EN 806) treatment is not covered by warranty. Refer to the dimensional drawing on fold-outⅠ. Do not use any abrasive sponges or scouring Refer to the installation step guide fig. [1-4] agents for cleaning. We also advise you not to The cold water supply must be connected on use cleaning agents containing solvent or acid, the right and the hot water supply onthe left. limescale removers, household vinegar and Open cold and hot water supplies and check cleaning agents with acetic acid in them. They connections for leak tightness. are aggressive to the surface and will leave Please check the installation for ensuring your fitting dull and scratched. As the formutations correct function. of commercially available cleaning agents frequently charge, we cannot guarantee they will provide the gentle care our fitting deserves. Maintenance Clean the fitting with a little soap and a moist Shut off cold and hot water supply! cloth only, then simply rinse off and wipe dry. You can avoid lime spots by drying the fitting Ⅰ Replace or clean the inlet accessories, see each time it is used. fig. [5] Remove nut (A) anti-clockwise with monkey wrench, and take out the filter (B) to clean or replace if necessary. Clean or replace fittings (C), please just anti-clockwise screw off nut (A) with monkey wrench. Screw out internal part (C1) and remove check valve (C2) for cleaning or replacement if necessary.
Ø203mm Ø8"
71. 5mm 2 13/16"
Temperature --Hot water inlet (maximum) 90 ℃ Correct operation suggestion: --Hot water inlet temperature 55℃ ≤ T ≤ 65℃ --Recommended (energy saving) 60 ℃ --Cold water inlet temperature T ≤ 25℃ Water connection Cold-Right Hot-Left
Ⅲ Replace or clean the quarter turn cartridge, see fig. [7] Lever out handle cap (A); Remove screw (B) using a cross-head screwdriver; Take out handle set (C); Screw off quarter turn cartridge (D) anti-clockwise with a monkey wrench; Replace cartridge (D).
42mm 1 5/8"
1bar 5bar 16bar
90
Pressure range: Minimum flow pressure Maximum operating pressure Air leakage pressure
Ø60mm Ø2 3/ 8"
Pressure range
370mm 14 9/16"
80-3 80mm 3 1 / 8 " - 1 4 15/1 6"
Can be used in conjunction with: Pressurised storage heaters, thermally and hydraulically controlled instantaneous heaters. Operation with low-pressure displacement water heaters is not possible.
Ⅱ Replace or clean the thermostatic cartridge, see fig. [6] Lever out handle cap(A); Remove screw (B) using a cross-head screwdriver; Take out handle set (C) and limit ring (D); Screw off nut (E) anti-clockwise using a pin spanner, and then remove screw (F) using a 2mm Allen key. Replace cartridge (G).
737mm 29"
GB Application
Ø9mm Ø3/ 8" 262mm 10 5/ 16"
Ⅰ
1
ES101
5
2
Connect the S-shaped connectors to pipe work and screw the fixation seat in place.
Install the thermostatic bar valve onto the inlet connectors.
Replace or clean the inlet accessories C1
C2
RP027139
30
m
m
Ø6m m Ø1/ 4 "
C B
737mm ( 29" )
A
RP551073
RP078004
RP020001 RP062000 RP103141
Sugges1. 1m( 43 5/16")
RP125023 RP027008 RP058287 RP223000
RP032000
RP026000 RP020041
m 25m 1 5 0± 8 " ± 1 " 5 7/
sealing tape
6 B
Replace the thermostatic car tridge
C D
RP026003
RP027309
3
RP426004
G
4
Connect the shower kit to thermostatic bar valve.
RP130021
A
RP058290
F
Operate the product for a couple of minutes, varying both temperature and volume to determine correct operation.
H2 m
E The cartridge is at 38C when the dot and groove/line are aligned.
Align the screw hole with the recess position on the cartridge.
m
RP031056 RP024310 RP044218 RP044942
RP027126
RP081028
RP044539 RP518000 RP044540
RP025042 RP038369-90 RP075011 RP033053
7
4 RP020020
Replace quar ter turn car tridge
5 2.5mm
RP058437
RP048064 RP027001
RP530029
35mm
The flow restrictor is only needed when water pressure is above 5bar or where the hot water heater cannot keep up with the flow rate.
m m
RP024084 RP044041 RP058003
3 2
15
RP062003
RP055014
RP020010
1
RP038370-90
29mm
RP020189 RP027002 RP040000
D
RP531028H
A
RP034094
Ⅱ
Ⅲ
B
C
Ⅳ
Product Care
Thermostatic Bar Mixer with Fixed Head ANGEL SHOWER
Ⅴ
148. 5mm 5 7/ 8" 71.5- 76. 5mm 2 13/16"-3"
15 0±2 5m m 5 7 / 8 " ±1"
Off On
2- Ø60mm 2-Ø2 3/ 8" 2 - G1 / 2B Ø39mm Ø1 9/ 16"
32.5mm 1 1/ 4"
Dear Customer, We want to ensure that you get long-lasting satisfaction and pleasure from your fitting. Installation Therefore, please read the following care Flush piping system prior and after instructions because damage to the surface installation of fitting thoroughly and underlying material resulting from improper (consider EN 806) treatment is not covered by warranty. Refer to the dimensional drawing on fold-outⅠ. Do not use any abrasive sponges or scouring Refer to the installation step guide fig. [1-4] agents for cleaning. We also advise you not to The cold water supply must be connected on use cleaning agents containing solvent or acid, the right and the hot water supply onthe left. limescale removers, household vinegar and Open cold and hot water supplies and check cleaning agents with acetic acid in them. They connections for leak tightness. are aggressive to the surface and will leave Please check the installation for ensuring your fitting dull and scratched. As the formutations correct function. of commercially available cleaning agents frequently charge, we cannot guarantee they will provide the gentle care our fitting deserves. Maintenance Clean the fitting with a little soap and a moist Shut off cold and hot water supply! cloth only, then simply rinse off and wipe dry. You can avoid lime spots by drying the fitting Ⅰ Replace or clean the inlet accessories, see each time it is used. fig. [5] Remove nut (A) anti-clockwise with monkey wrench, and take out the filter (B) to clean or replace if necessary. Clean or replace fittings (C), please just anti-clockwise screw off nut (A) with monkey wrench. Screw out internal part (C1) and remove check valve (C2) for cleaning or replacement if necessary.
Ø203mm Ø8"
71. 5mm 2 13/16"
Temperature --Hot water inlet (maximum) 90 ℃ Correct operation suggestion: --Hot water inlet temperature 55℃ ≤ T ≤ 65℃ --Recommended (energy saving) 60 ℃ --Cold water inlet temperature T ≤ 25℃ Water connection Cold-Right Hot-Left
Ⅲ Replace or clean the quarter turn cartridge, see fig. [7] Lever out handle cap (A); Remove screw (B) using a cross-head screwdriver; Take out handle set (C); Screw off quarter turn cartridge (D) anti-clockwise with a monkey wrench; Replace cartridge (D).
42mm 1 5/8"
1bar 5bar 16bar
90
Pressure range: Minimum flow pressure Maximum operating pressure Air leakage pressure
Ø60mm Ø2 3/ 8"
Pressure range
370mm 14 9/16"
80-3 80mm 3 1 / 8 " - 1 4 15/1 6"
Can be used in conjunction with: Pressurised storage heaters, thermally and hydraulically controlled instantaneous heaters. Operation with low-pressure displacement water heaters is not possible.
Ⅱ Replace or clean the thermostatic cartridge, see fig. [6] Lever out handle cap(A); Remove screw (B) using a cross-head screwdriver; Take out handle set (C) and limit ring (D); Screw off nut (E) anti-clockwise using a pin spanner, and then remove screw (F) using a 2mm Allen key. Replace cartridge (G).
737mm 29"
GB Application
Ø9mm Ø3/ 8" 262mm 10 5/ 16"
Ⅰ
1
ES101
5
2
Connect the S-shaped connectors to pipe work and screw the fixation seat in place.
Install the thermostatic bar valve onto the inlet connectors.
Replace or clean the inlet accessories C1
C2
RP027139
30
m
m
Ø6m m Ø1/ 4 "
C B
737mm ( 29" )
A
RP551073
RP078004
RP020001 RP062000 RP103141
Sugges1. 1m( 43 5/16")
RP125023 RP027008 RP058287 RP223000
RP032000
RP026000 RP020041
m 25m 1 5 0± 8 " ± 1 " 5 7/
sealing tape
6 B
Replace the thermostatic car tridge
C D
RP026003
RP027309
3
RP426004
G
4
Connect the shower kit to thermostatic bar valve.
RP130021
A
RP058290
F
Operate the product for a couple of minutes, varying both temperature and volume to determine correct operation.
H2 m
E The cartridge is at 38C when the dot and groove/line are aligned.
Align the screw hole with the recess position on the cartridge.
m
RP031056 RP024310 RP044218 RP044942
RP027126
RP081028
RP044539 RP518000 RP044540
RP025042 RP038369-90 RP075011 RP033053
7
4 RP020020
Replace quar ter turn car tridge
5 2.5mm
RP058437
RP048064 RP027001
RP530029
35mm
The flow restrictor is only needed when water pressure is above 5bar or where the hot water heater cannot keep up with the flow rate.
m m
RP024084 RP044041 RP058003
3 2
15
RP062003
RP055014
RP020010
1
RP038370-90
29mm
RP020189 RP027002 RP040000
D
RP531028H
A
RP034094
Ⅱ
Ⅲ
B
C
Ⅳ
