DeWalt D28110 Power Cord Replacement
DeWalt D28110 Power Cord Replacement
DeWalt D28110 Power Cord Replacement A torn or malfunctioning power cord is dangerous and may be the reason for loss of power. This guide explains how to replace the entire cable.
Written By: Andrew
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
DeWalt D28110 Power Cord Replacement
INTRODUCTION This guide will take you through removing the back panel assembly and disconnecting the power cable from the inner electric components.
TOOLS: JIS Driver Set (1) Spudger (1) T15 Security Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
DeWalt D28110 Power Cord Replacement
Step 1 — Disassembling DeWalt D28110 Back Panel Disassembly
Using the T-15 screwdriver, remove the four 22-mm torx screws holding the back panel in place.
Unplug the grinder before any disassembly.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Use the edge of the spudger to loosen and remove the back panel.
Page 3 of 5
DeWalt D28110 Power Cord Replacement
Step 3
Remove the single 20-mm torx screw holding the rear panel in place.
Pull back the rear side of the back panel.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
DeWalt D28110 Power Cord Replacement
Step 5 — Power Cord
Locate the red switch box.
Using the J-10 screwdriver, unscrew the screws and detach the wires.
Be sure to remember under which screw the "ground" wire (black) goes. Step 6
Unthread the two wires from the power cord clamp.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2018-01-19 06:12:39 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
DeWalt D28110 Power Cord Replacement A torn or malfunctioning power cord is dangerous and may be the reason for loss of power. This guide explains how to replace the entire cable.
Written By: Andrew
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
DeWalt D28110 Power Cord Replacement
INTRODUCTION This guide will take you through removing the back panel assembly and disconnecting the power cable from the inner electric components.
TOOLS: JIS Driver Set (1) Spudger (1) T15 Security Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
DeWalt D28110 Power Cord Replacement
Step 1 — Disassembling DeWalt D28110 Back Panel Disassembly
Using the T-15 screwdriver, remove the four 22-mm torx screws holding the back panel in place.
Unplug the grinder before any disassembly.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Use the edge of the spudger to loosen and remove the back panel.
Page 3 of 5
DeWalt D28110 Power Cord Replacement
Step 3
Remove the single 20-mm torx screw holding the rear panel in place.
Pull back the rear side of the back panel.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
DeWalt D28110 Power Cord Replacement
Step 5 — Power Cord
Locate the red switch box.
Using the J-10 screwdriver, unscrew the screws and detach the wires.
Be sure to remember under which screw the "ground" wire (black) goes. Step 6
Unthread the two wires from the power cord clamp.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2018-01-19 06:12:39 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
