Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board This is a prerequisite only. If the screen or microphone are faulty the entire circuit board will need to be replaced.
Written By: James Tucker Dunn
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
INTRODUCTION The Circuit board has the screen and microphone attached, but the speaker and antenna can be modified separately.
TOOLS:
PARTS:
Phillips #0 Screwdriver (1)
Replacement Circuit Board (1)
Soldering Station (1) Spudger (1) Flush Wire Cutters (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Step 1 — Batteries
First, apply pressure with your thumb on the top of the battery cover.
Next, pull down on the cover until it begins to slide.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Step 3
Finally, once the cover is completely off, pry up the old batteries with your finger or a strong, skinny tool (i.e. spudger).
Unscrew the six 8.0 millimeter long, #0 screws on the backside of the case using the Phillips #0 screwdriver.
Step 4 — Case
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Step 5
Detach back part of the case by gently lifting up.
Remove the old or broken circuit board from the front case.
Clip the red and black wires at the base of the motherboard to completely separate it from the radio case.
Step 6 — Circuit Board
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 03:20:55 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board This is a prerequisite only. If the screen or microphone are faulty the entire circuit board will need to be replaced.
Written By: James Tucker Dunn
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
INTRODUCTION The Circuit board has the screen and microphone attached, but the speaker and antenna can be modified separately.
TOOLS:
PARTS:
Phillips #0 Screwdriver (1)
Replacement Circuit Board (1)
Soldering Station (1) Spudger (1) Flush Wire Cutters (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Step 1 — Batteries
First, apply pressure with your thumb on the top of the battery cover.
Next, pull down on the cover until it begins to slide.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Step 3
Finally, once the cover is completely off, pry up the old batteries with your finger or a strong, skinny tool (i.e. spudger).
Unscrew the six 8.0 millimeter long, #0 screws on the backside of the case using the Phillips #0 screwdriver.
Step 4 — Case
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Step 5
Detach back part of the case by gently lifting up.
Remove the old or broken circuit board from the front case.
Clip the red and black wires at the base of the motherboard to completely separate it from the radio case.
Step 6 — Circuit Board
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 03:20:55 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
