Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board This is a prerequisite only. If the screen or microphone are faulty the entire circuit board will need to be replaced.
Geschreven door: James Tucker Dunn
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 1 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
INTRODUCTIE The Circuit board has the screen and microphone attached, but the speaker and antenna can be modified separately.
GEREEDSCHAPPEN:
ONDERDELEN:
Phillips #0 Screwdriver (1)
Replacement Circuit Board (1)
Soldering Station (1) Spudger (1) Flush Wire Cutters (1)
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 2 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Stap 1 — Batteries
First, apply pressure with your thumb on the top of the battery cover.
Next, pull down on the cover until it begins to slide.
Stap 2
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 3 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Stap 3
Finally, once the cover is completely off, pry up the old batteries with your finger or a strong, skinny tool (i.e. spudger).
Unscrew the six 8.0 millimeter long, #0 screws on the backside of the case using the Phillips #0 screwdriver.
Stap 4 — Case
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 4 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Stap 5
Detach back part of the case by gently lifting up.
Remove the old or broken circuit board from the front case.
Clip the red and black wires at the base of the motherboard to completely separate it from the radio case.
Stap 6 — Circuit Board
To reassemble your device, follow these instructions in reverse order. Dit document is voor het laatst gegenereerd op 2017-10-02 10:18:00 PM.
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 5 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board This is a prerequisite only. If the screen or microphone are faulty the entire circuit board will need to be replaced.
Geschreven door: James Tucker Dunn
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 1 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
INTRODUCTIE The Circuit board has the screen and microphone attached, but the speaker and antenna can be modified separately.
GEREEDSCHAPPEN:
ONDERDELEN:
Phillips #0 Screwdriver (1)
Replacement Circuit Board (1)
Soldering Station (1) Spudger (1) Flush Wire Cutters (1)
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 2 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Stap 1 — Batteries
First, apply pressure with your thumb on the top of the battery cover.
Next, pull down on the cover until it begins to slide.
Stap 2
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 3 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Stap 3
Finally, once the cover is completely off, pry up the old batteries with your finger or a strong, skinny tool (i.e. spudger).
Unscrew the six 8.0 millimeter long, #0 screws on the backside of the case using the Phillips #0 screwdriver.
Stap 4 — Case
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 4 van 5
Disassembling Midland X-tra Talk Radio LXT118 Circuit Board
Stap 5
Detach back part of the case by gently lifting up.
Remove the old or broken circuit board from the front case.
Clip the red and black wires at the base of the motherboard to completely separate it from the radio case.
Stap 6 — Circuit Board
To reassemble your device, follow these instructions in reverse order. Dit document is voor het laatst gegenereerd op 2017-10-02 10:18:00 PM.
© iFixit — CC BY-NC-SA
nl.iFixit.com
Pagina 5 van 5
