005a ST-700-Gen3-Configure-Router-Wireless
Instructions for SimplicityTouch ST-700 Gen 3 Configure Router for Wireless Connection Topics Covered: How to configure internal router for wireless connection
Model Numbers Covered: 70” ST-700, Generation 3 Last Update:12/1/2016 e: [email protected]
TOOLS REQUIRED: None.
ESTIMATED TIME REQUIRED: Less than 10 min.
Configure Router for Wireless Network using pre-shared key
The SimplicityTouch can be configured to connect directly to your network via the internal router. The internal router supports several features: 1) Wired connection (this is preferred and most common way to connect panel). See separate user guide for wired connection instructions. 2) Wireless connection via Pre-shared Key. 3) Act as wireless access point allowing users to share the panels connection to local network (note, this is typically disabled and not used in commercial environments).
The following instructions are how to connect by wireless connection via pre-shared key. Also, included are optional instructions for how to change router login info and save configuration to a file so that settings can be re-loaded from a USB drive.
STEP REFERENCE IMAGE
INSTRUCTIONS
1
Power on panel wait for panel to boot up to an input screen.
2
Press the Home button on remote or on keypad on front of panel. This will open the on screen menu display.
STEP REFERENCE IMAGE
INSTRUCTIONS
3
Press Settings and then enter the password to access the home screen settings.
Note: Default password is 0 0 0 0. It is recommended that you change this password.
4
Select Network.
STEP REFERENCE IMAGE
INSTRUCTIONS
5
Select Router Settings.
6
Login to router.
Note: Default login is: UserName: Admin Password: [leave blank] It is recommended that you change the password.
STEP REFERENCE IMAGE
INSTRUCTIONS
7
Select Easy Setup Wizard from left menu.
8
Select Wireless ISP mode and then Next.
STEP REFERENCE IMAGE
INSTRUCTIONS
9
Set WAN Access Type to DHCP Client. Set 5GHz Broadcast SSID to Disabled. Set 5GHz Mode to Client. Set 2.4GHz Broadcast SSID to Disabled. Set 2.4GHz Mode to Client. Select Finished.
STEP REFERENCE IMAGE
INSTRUCTIONS
10
After page refreshes and router admin page is displayed select Site Survey from the left menu.
11
Press Site Survey button.
STEP REFERENCE IMAGE
INSTRUCTIONS
12
Press Settings and then enter the password to access the home screen settings.
Note: Default password is 0 0 0 0. It is recommended that you change this password.
13
Enter your network password. Then press Connect. Wait for router to connect.
STEP REFERENCE IMAGE
INSTRUCTIONS
14
Check the Add to Wireless Profile box then press Reboot Now.
15
Wait for router to reset.
STEP REFERENCE IMAGE
INSTRUCTIONS
16
When router reboots and the refreshes the Access Point Status page confirm that you are connected to your network and that an IP has been received from DHCP server. NOTE: it can sometimes take up to several minutes on some networks for the IP address to be issued. Refresh the page to see if the IP has been assigned.
STEP REFERENCE IMAGE
INSTRUCTIONS
17
It is a good idea to change the password of the router to prevent unauthorized access. Follow these steps (17-18) to change the password.
Select Advanced Mode from left menu.
18
Then select Password from left menu and use form to update the User Name and Password. Then press Apply Changes.
Note: Store username and password in a safe location for future recover in case PW is forgotten.
STEP REFERENCE IMAGE
INSTRUCTIONS
19
After configuring router successfully it is a good idea to save the router configuration to a USB drive so that it can be used later to configure subsequent panels that are connecting to the same network. First, plug in a USB drive into the panel using one of the USB ports labeled with the Home Screen icon.
Login to router and then select Advanced Mode from left menu.
20
Select SAVE/RELOAD SETTINGS from left menu.
STEP REFERENCE IMAGE
INSTRUCTIONS
21
Press Save and the file will automatically be saved to the USB drive that is plugged into the panel. It will be saved under the Downloads folder on the USB drive.
STEP REFERENCE IMAGE
INSTRUCTIONS
22
To load the router configuration from a USB drive simply place the config.dat file that you saved in step 21 on any USB drive and then plug that drive into the other panel(s) to be configured and follow the instructions to follow (steps 22 - 33) First, plug a USB drive with the config.dat file into the panel using one of the USB ports labeled with the Home Screen icon.
Login to router and then select Advanced Mode from left menu. 23
Select SAVE/RELOAD SETTINGS from left menu.
STEP REFERENCE IMAGE
INSTRUCTIONS
24
Select Browse.
25
Select Documents from the chooser menu.
STEP REFERENCE IMAGE
INSTRUCTIONS
26
Then select ES File Explorer.
27
Then tap on the top path (/storage/emulated/0) to go up one level.
STEP REFERENCE IMAGE
INSTRUCTIONS
28
Then select /mnt/usb/sda1 (if you have plugged in more than one USB drive you may see /mnt/usb/sdb1 instead).
29
Select Download folder.
STEP REFERENCE IMAGE
INSTRUCTIONS
30
Then select config.dat file.
31
Select Normal Android Way.
STEP REFERENCE IMAGE
INSTRUCTIONS
32
Then select Upload.
33
Wait for panel to reboot and apply the settings from the config.dat file.
NOTE: This is a good way to allow install personnel to configure the router without giving them any of the passwords. They can login under default password, then load the config.dat file and it will update the router password, and apply all settings to connect to the network.
END OF INSTRUCTIONS
Model Numbers Covered: 70” ST-700, Generation 3 Last Update:12/1/2016 e: [email protected]
TOOLS REQUIRED: None.
ESTIMATED TIME REQUIRED: Less than 10 min.
Configure Router for Wireless Network using pre-shared key
The SimplicityTouch can be configured to connect directly to your network via the internal router. The internal router supports several features: 1) Wired connection (this is preferred and most common way to connect panel). See separate user guide for wired connection instructions. 2) Wireless connection via Pre-shared Key. 3) Act as wireless access point allowing users to share the panels connection to local network (note, this is typically disabled and not used in commercial environments).
The following instructions are how to connect by wireless connection via pre-shared key. Also, included are optional instructions for how to change router login info and save configuration to a file so that settings can be re-loaded from a USB drive.
STEP REFERENCE IMAGE
INSTRUCTIONS
1
Power on panel wait for panel to boot up to an input screen.
2
Press the Home button on remote or on keypad on front of panel. This will open the on screen menu display.
STEP REFERENCE IMAGE
INSTRUCTIONS
3
Press Settings and then enter the password to access the home screen settings.
Note: Default password is 0 0 0 0. It is recommended that you change this password.
4
Select Network.
STEP REFERENCE IMAGE
INSTRUCTIONS
5
Select Router Settings.
6
Login to router.
Note: Default login is: UserName: Admin Password: [leave blank] It is recommended that you change the password.
STEP REFERENCE IMAGE
INSTRUCTIONS
7
Select Easy Setup Wizard from left menu.
8
Select Wireless ISP mode and then Next.
STEP REFERENCE IMAGE
INSTRUCTIONS
9
Set WAN Access Type to DHCP Client. Set 5GHz Broadcast SSID to Disabled. Set 5GHz Mode to Client. Set 2.4GHz Broadcast SSID to Disabled. Set 2.4GHz Mode to Client. Select Finished.
STEP REFERENCE IMAGE
INSTRUCTIONS
10
After page refreshes and router admin page is displayed select Site Survey from the left menu.
11
Press Site Survey button.
STEP REFERENCE IMAGE
INSTRUCTIONS
12
Press Settings and then enter the password to access the home screen settings.
Note: Default password is 0 0 0 0. It is recommended that you change this password.
13
Enter your network password. Then press Connect. Wait for router to connect.
STEP REFERENCE IMAGE
INSTRUCTIONS
14
Check the Add to Wireless Profile box then press Reboot Now.
15
Wait for router to reset.
STEP REFERENCE IMAGE
INSTRUCTIONS
16
When router reboots and the refreshes the Access Point Status page confirm that you are connected to your network and that an IP has been received from DHCP server. NOTE: it can sometimes take up to several minutes on some networks for the IP address to be issued. Refresh the page to see if the IP has been assigned.
STEP REFERENCE IMAGE
INSTRUCTIONS
17
It is a good idea to change the password of the router to prevent unauthorized access. Follow these steps (17-18) to change the password.
Select Advanced Mode from left menu.
18
Then select Password from left menu and use form to update the User Name and Password. Then press Apply Changes.
Note: Store username and password in a safe location for future recover in case PW is forgotten.
STEP REFERENCE IMAGE
INSTRUCTIONS
19
After configuring router successfully it is a good idea to save the router configuration to a USB drive so that it can be used later to configure subsequent panels that are connecting to the same network. First, plug in a USB drive into the panel using one of the USB ports labeled with the Home Screen icon.
Login to router and then select Advanced Mode from left menu.
20
Select SAVE/RELOAD SETTINGS from left menu.
STEP REFERENCE IMAGE
INSTRUCTIONS
21
Press Save and the file will automatically be saved to the USB drive that is plugged into the panel. It will be saved under the Downloads folder on the USB drive.
STEP REFERENCE IMAGE
INSTRUCTIONS
22
To load the router configuration from a USB drive simply place the config.dat file that you saved in step 21 on any USB drive and then plug that drive into the other panel(s) to be configured and follow the instructions to follow (steps 22 - 33) First, plug a USB drive with the config.dat file into the panel using one of the USB ports labeled with the Home Screen icon.
Login to router and then select Advanced Mode from left menu. 23
Select SAVE/RELOAD SETTINGS from left menu.
STEP REFERENCE IMAGE
INSTRUCTIONS
24
Select Browse.
25
Select Documents from the chooser menu.
STEP REFERENCE IMAGE
INSTRUCTIONS
26
Then select ES File Explorer.
27
Then tap on the top path (/storage/emulated/0) to go up one level.
STEP REFERENCE IMAGE
INSTRUCTIONS
28
Then select /mnt/usb/sda1 (if you have plugged in more than one USB drive you may see /mnt/usb/sdb1 instead).
29
Select Download folder.
STEP REFERENCE IMAGE
INSTRUCTIONS
30
Then select config.dat file.
31
Select Normal Android Way.
STEP REFERENCE IMAGE
INSTRUCTIONS
32
Then select Upload.
33
Wait for panel to reboot and apply the settings from the config.dat file.
NOTE: This is a good way to allow install personnel to configure the router without giving them any of the passwords. They can login under default password, then load the config.dat file and it will update the router password, and apply all settings to connect to the network.
END OF INSTRUCTIONS
