11 x 7.7
Daniel Porrey Snap Circuits IoT https://www.hackster.io/porrey
Parts List Quantity
Seven Segment Display 1
2
3
4
5
6
7
8
Name
Part #
1
Base Grid Base Grid (11 x 7.7)
6SCBG
1
2-snap wire
6SC02
1
D7
Seven Segment Display
6SCD7
1
R1
100 Ω Resistor
6SCR1
Snap-to-Pin wire
SCJW10
9
9
10
ID
Step by Step Guide 1) Snap component R1 between B6 and B8
A
2) Snap the component D7 between C7, C9, F7 and F9
B To the 3V3 pin on the Arduino Uno (red wire)
C D E
A (yellow) to pin 1 B (white) to pin 2 C (white) to pin 3 D (green) to pin 4 E (green) to pin 5 F (yellow) to pin 6 G (black) to pin 7 DP (black) to pin 8
3) Snap a 2 snap wire over the components between B8 and C8 4) Connect the snap end of a red wire onto the component at position B6 5) Plug the male pin end of the red wire from step 4 into the 3V3 pin on the Arduino Uno board 6) Connect the snap end of a yellow wire onto the component at position C7 7) Plug the bread board end of the yellow wire from step 6 into pin 1 on the Arduino Uno board
F
8) Connect the snap end of a yellow wire onto the component at position D7
G OBJECTIVE: Count from 0 to 9 on a seven segment display.
9) Plug the bread board end of the yellow wire from step 8 into pin 2 on the Arduino Uno board 10) Connect the snap end of a green wire onto the component at position E7 11) Plug the bread board end of the green wire from step 10 into pin 3 on the Arduino Uno board 12) Connect the snap end of a green wire onto the component at position F7
Copyright © 2015 by Daniel M. Porrey. All Rights Reserved
Page 1 of 2
Daniel Porrey Snap Circuits IoT https://www.hackster.io/porrey
Step by Step Guide (continued) 13) Plug the bread board end of the green wire from step 12 into pin 4 on the Arduino Uno board 14) Connect the snap end of a white wire onto the component at position C9 15) Plug the bread board end of the white wire from step 14 into pin 5 on the Arduino Uno board 16) Connect the snap end of a black wire onto the component at position D9 17) Plug the bread board end of the black wire from step 16 into pin 6 on the Arduino Uno board 18) Connect the snap end of a white wire onto the component at position E9 19) Plug the bread board end of the white wire from step 18 into pin 7 on the Arduino Uno board 20) Connect the snap end of a black wire onto the component at position F9 21) Plug the bread board end of the black wire from step 16 into pin 8 on the Arduino Uno board 22) Open the sketch for Seven Segment Display in the Arduino IDE and upload it to the board.
Copyright © 2015 by Daniel M. Porrey. All Rights Reserved
Page 2 of 2
Parts List Quantity
Seven Segment Display 1
2
3
4
5
6
7
8
Name
Part #
1
Base Grid Base Grid (11 x 7.7)
6SCBG
1
2-snap wire
6SC02
1
D7
Seven Segment Display
6SCD7
1
R1
100 Ω Resistor
6SCR1
Snap-to-Pin wire
SCJW10
9
9
10
ID
Step by Step Guide 1) Snap component R1 between B6 and B8
A
2) Snap the component D7 between C7, C9, F7 and F9
B To the 3V3 pin on the Arduino Uno (red wire)
C D E
A (yellow) to pin 1 B (white) to pin 2 C (white) to pin 3 D (green) to pin 4 E (green) to pin 5 F (yellow) to pin 6 G (black) to pin 7 DP (black) to pin 8
3) Snap a 2 snap wire over the components between B8 and C8 4) Connect the snap end of a red wire onto the component at position B6 5) Plug the male pin end of the red wire from step 4 into the 3V3 pin on the Arduino Uno board 6) Connect the snap end of a yellow wire onto the component at position C7 7) Plug the bread board end of the yellow wire from step 6 into pin 1 on the Arduino Uno board
F
8) Connect the snap end of a yellow wire onto the component at position D7
G OBJECTIVE: Count from 0 to 9 on a seven segment display.
9) Plug the bread board end of the yellow wire from step 8 into pin 2 on the Arduino Uno board 10) Connect the snap end of a green wire onto the component at position E7 11) Plug the bread board end of the green wire from step 10 into pin 3 on the Arduino Uno board 12) Connect the snap end of a green wire onto the component at position F7
Copyright © 2015 by Daniel M. Porrey. All Rights Reserved
Page 1 of 2
Daniel Porrey Snap Circuits IoT https://www.hackster.io/porrey
Step by Step Guide (continued) 13) Plug the bread board end of the green wire from step 12 into pin 4 on the Arduino Uno board 14) Connect the snap end of a white wire onto the component at position C9 15) Plug the bread board end of the white wire from step 14 into pin 5 on the Arduino Uno board 16) Connect the snap end of a black wire onto the component at position D9 17) Plug the bread board end of the black wire from step 16 into pin 6 on the Arduino Uno board 18) Connect the snap end of a white wire onto the component at position E9 19) Plug the bread board end of the white wire from step 18 into pin 7 on the Arduino Uno board 20) Connect the snap end of a black wire onto the component at position F9 21) Plug the bread board end of the black wire from step 16 into pin 8 on the Arduino Uno board 22) Open the sketch for Seven Segment Display in the Arduino IDE and upload it to the board.
Copyright © 2015 by Daniel M. Porrey. All Rights Reserved
Page 2 of 2
