2TouchPOS Replacing Mag Reader & Cable User's Guide
2TouchPOS Replacing Mag Reader & Cable User’s Guide
2013 Xenios LLC 82 Saint Paul Street Rochester, NY 14604 Phone 585.325.5242 • Fax 585.325.6989
Contents About this Document .................................................................................................................. 3 Replacing Mag Reader & Cable.................................................................................................. 4 Reattach Mag Reader ................................................................................................................ 10
Xenios LLC @ 2013
Page 2
About this Document This document was written for 2TouchPOS version 3.03.4900.
Xenios LLC @ 2013
Page 3
Replacing Mag Reader & Cable 1. Make sure your 2TouchPOS system is shut down. Posiflex sign will be a light green color. 2. Disconnect power, hard drive power and sata cables.
Xenios LLC @ 2013
Page 4
3. Remove Base from monitor by pressing a plastic clip, located on the backside of your terminal. Hold the clip, place other hand on the terminals front side of your Posiflex touch screen and lift screen up. Place monitor on a flat clean surface.
Xenios LLC @ 2013
Page 5
4. Remove mag reader from monitor. Unscrew, the two screws holding the mag reader to monitor.
5. Unplug mag reader’s cable from monitor. BE CAREFUL, there is a cable connecting the hard drive to mag reader. Unplug mag reader cable from mag reader.
Xenios LLC @ 2013
Page 6
6. Unscrew the four monitor screws, located in all four corners.
7. Lift back proportion of monitor. BE CAREFUL, there are wires attached. Lift slowly.
Xenios LLC @ 2013
Page 7
8. Find mag reader cable and slide it through the mag reader port.
Xenios LLC @ 2013
Page 8
9. Pull mag reader cable out from hard drive clip.
10. Attach new mag reader cable to hard drive clip by attaching the cables five pin end into the mag reader clip. When inserting the five pin end, attach it to the bottom proportion of the mag reader’s clip. Re-insert mag reader cable through port in monitor.
Xenios LLC @ 2013
Page 9
11. Close monitor up. Line up all four screw holes and you will hear a snapping noise when monitor is in place. Screw in all four monitor screws. (Hand Tight Only).
Reattach Mag Reader 1. Take mag reader cable and attach it to the mag reader.
2. Re-attach mag reader by screwing in 2 screws. (Hand Tight Only).
Xenios LLC @ 2013
Page 10
3. Re-Attach the hard drive power and sata cables.
4. Re-attach monitor to base. First, insert bottom proportion of monitor into base.
Xenios LLC @ 2013
Page 11
5. Re-attach power cable.
Xenios LLC @ 2013
Page 12
2013 Xenios LLC 82 Saint Paul Street Rochester, NY 14604 Phone 585.325.5242 • Fax 585.325.6989
Contents About this Document .................................................................................................................. 3 Replacing Mag Reader & Cable.................................................................................................. 4 Reattach Mag Reader ................................................................................................................ 10
Xenios LLC @ 2013
Page 2
About this Document This document was written for 2TouchPOS version 3.03.4900.
Xenios LLC @ 2013
Page 3
Replacing Mag Reader & Cable 1. Make sure your 2TouchPOS system is shut down. Posiflex sign will be a light green color. 2. Disconnect power, hard drive power and sata cables.
Xenios LLC @ 2013
Page 4
3. Remove Base from monitor by pressing a plastic clip, located on the backside of your terminal. Hold the clip, place other hand on the terminals front side of your Posiflex touch screen and lift screen up. Place monitor on a flat clean surface.
Xenios LLC @ 2013
Page 5
4. Remove mag reader from monitor. Unscrew, the two screws holding the mag reader to monitor.
5. Unplug mag reader’s cable from monitor. BE CAREFUL, there is a cable connecting the hard drive to mag reader. Unplug mag reader cable from mag reader.
Xenios LLC @ 2013
Page 6
6. Unscrew the four monitor screws, located in all four corners.
7. Lift back proportion of monitor. BE CAREFUL, there are wires attached. Lift slowly.
Xenios LLC @ 2013
Page 7
8. Find mag reader cable and slide it through the mag reader port.
Xenios LLC @ 2013
Page 8
9. Pull mag reader cable out from hard drive clip.
10. Attach new mag reader cable to hard drive clip by attaching the cables five pin end into the mag reader clip. When inserting the five pin end, attach it to the bottom proportion of the mag reader’s clip. Re-insert mag reader cable through port in monitor.
Xenios LLC @ 2013
Page 9
11. Close monitor up. Line up all four screw holes and you will hear a snapping noise when monitor is in place. Screw in all four monitor screws. (Hand Tight Only).
Reattach Mag Reader 1. Take mag reader cable and attach it to the mag reader.
2. Re-attach mag reader by screwing in 2 screws. (Hand Tight Only).
Xenios LLC @ 2013
Page 10
3. Re-Attach the hard drive power and sata cables.
4. Re-attach monitor to base. First, insert bottom proportion of monitor into base.
Xenios LLC @ 2013
Page 11
5. Re-attach power cable.
Xenios LLC @ 2013
Page 12
