369381 LOW-VOLTAGE ENCLOSURE Spec Submittal Sheet - Lutron
product specifications
369-381a
03.09.11
Low-Voltage Enclosure Low-voltage enclosures may be either surface-mounted or flush-mounted in an electrical closet or equipment room. Both the number of enclosures and the types of components within them are customized to fit the size, lighting plan, and design of a home. Low-voltage enclosures can be distributed throughout the home near the rooms they are controlling, to provide maximum flexibility during installation of the low-voltage wiring. Low-voltage enclosures cannot house remote power modules (RPMs). 21-inch Low-Voltage Enclosure (Model # HQ-LV21-120) The twenty-one-inch low-voltage enclosure provides a compact housing for mounting up to two HomeWorks QS processors or up to two system interfaces and up to five wire landing boards (QS-WLB). The enclosure accepts one 120 V~ feed to power the panel, which is self-contained in an enclosed area, thus allowing access to only the low-voltage connections when the enclosure cover is removed.
Low-Voltage Enclosure (HQ-LV21-120)
Model Number HQ-LV21-120
Low-Voltage Enclosure
Low-Voltage Enclosure Cover (HQ-LV21-120)
www.lutron.com
Lutron® | 1
product specifications
369-381a
03.09.11
Low-Voltage Enclosure Specifications Model Number
HQ-LV21-120
Power
120 V~ Power Input 50 / 60 Hz 2 A
Regulatory Approvals
UL, CSA, NOM
Environment
Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C) Ambient operating humidity: 0-90% humidity, non-condensing. Indoor use only.
Mounting
Enclosure may be surface-mounted or recess-mounted. Enclosure fits between standard 16 in (41 cm) on-center stud framing. Mount the enclosure so that line-voltage wiring will be at least 6 feet (1.8 m) from audio or electronic equipment and wiring. Mount Enclosure using one of the following methods (mounting hardware is not provided): a. S urface Mount – Use keyholes with bolts sufficient for 100 lb (45 kg) load, 1/4 in (M6) bolts recommended. b. R ecess Mount – Use screws sufficient for 100 lb (45 kg) through the corners of the enclosure. Mount enclosure fully into the stud bay, with the back flush against the inner wall surface. Enclosure is 4.088 in (104 mm) deep past cover mounting tabs (including pedestal). Enclosure cover dimensions are 21.5 in x 15.386 in (546 mm x 391 mm). NOTICE: This equipment is air-cooled. Mount in a location where the vented cover will not be blocked. 12 in (305 mm) of clearance in front of the vents is required. NOTICE: Power supply will hum slightly and internal relays will click while in use. Mount in a location where such noise is acceptable.
Dimensions
Enclosure: 21 in (533 mm) x 14.375 in (365 mm) x 4.088 in (104 mm) Cover: 21.5 in (546 mm) x 15.386 in (391 mm)
Construction
Enclosure: 16-gauge powder coated sheet metal. Cover: 16-gauge powder coated metal cover. Cover is attached using four philips-head screws.
Capacity
Enclosure can accomodate two processors or system interface devices and five wire landing boards (QS-WLB). Examples: 1 Processor and 1 System Interface or 2 Processors or 2 Interfaces
Line-Voltage Connections
Use copper wire only, supply conductors rated at 167 ºF (75 °C). Use supplied wire connections to connect to corresponding power supply harnesses.
Warranty
8 Year Limited Warranty. http://www.lutron.com/resiinfo
2 | Lutron®
24/7 Technical Support—800.523.9466
product specifications
03.09.11
369-381a
Low-Voltage Enclosure Dimensions and Mounting 14.375 (365) 13.285 (337)
Measurements shown as: in (mm)
7.750 (197)
Terminal Shield
Surface Mounting Pedestal (4x)
Line voltage wiring entry (non-IEC PELV / NEC® Class 2)
Power Supply DIN rail End Stop (5x)
Input Power Switch
-7°
+7° 18.0 (457)
21 (533)
0.312 (7.9)
20.0 (508)
0.430 (10.9) 0.624 (15.8)
11.5 (292)
www.lutron.com
PELV / Class 2 ONLY
Lutron® | 3
product specifications
369-381a
03.09.11
Low-Voltage Enclosure Configuration
L(+) N(-)
120 - 240 V Input / Entrada / Entrée
L(+) N(-)
24 V Output / Salida / Sortie
QSPS-DH-1-60
120 - 240 V Input / Entrada / Entrée
Power Supply QSPS-DH-1-60 (up to 2)
24 V Output / Salida / Sortie
QSPS-DH-1-60
22.5 - 25 V
22.5 - 25 V
HomeWorks QS Processor HQP6-2-120 (up to 2)
QS Wire Landing Board QS-WLB (up to 5, 1 included)
Power Draw Information Power Supply
Power Draw Units Supplied
QSPS-DH-1-60
75 PDU
Device
Power Draw Units Required (per device)
Processor HQP6-2-120
8 PDU
QSE-CI-NWK-E
2 PDU
QSE-IO
3 PDU
4 | Lutron®
24/7 Technical Support—800.523.9466
369-381a
03.09.11
Low-Voltage Enclosure Low-voltage enclosures may be either surface-mounted or flush-mounted in an electrical closet or equipment room. Both the number of enclosures and the types of components within them are customized to fit the size, lighting plan, and design of a home. Low-voltage enclosures can be distributed throughout the home near the rooms they are controlling, to provide maximum flexibility during installation of the low-voltage wiring. Low-voltage enclosures cannot house remote power modules (RPMs). 21-inch Low-Voltage Enclosure (Model # HQ-LV21-120) The twenty-one-inch low-voltage enclosure provides a compact housing for mounting up to two HomeWorks QS processors or up to two system interfaces and up to five wire landing boards (QS-WLB). The enclosure accepts one 120 V~ feed to power the panel, which is self-contained in an enclosed area, thus allowing access to only the low-voltage connections when the enclosure cover is removed.
Low-Voltage Enclosure (HQ-LV21-120)
Model Number HQ-LV21-120
Low-Voltage Enclosure
Low-Voltage Enclosure Cover (HQ-LV21-120)
www.lutron.com
Lutron® | 1
product specifications
369-381a
03.09.11
Low-Voltage Enclosure Specifications Model Number
HQ-LV21-120
Power
120 V~ Power Input 50 / 60 Hz 2 A
Regulatory Approvals
UL, CSA, NOM
Environment
Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C) Ambient operating humidity: 0-90% humidity, non-condensing. Indoor use only.
Mounting
Enclosure may be surface-mounted or recess-mounted. Enclosure fits between standard 16 in (41 cm) on-center stud framing. Mount the enclosure so that line-voltage wiring will be at least 6 feet (1.8 m) from audio or electronic equipment and wiring. Mount Enclosure using one of the following methods (mounting hardware is not provided): a. S urface Mount – Use keyholes with bolts sufficient for 100 lb (45 kg) load, 1/4 in (M6) bolts recommended. b. R ecess Mount – Use screws sufficient for 100 lb (45 kg) through the corners of the enclosure. Mount enclosure fully into the stud bay, with the back flush against the inner wall surface. Enclosure is 4.088 in (104 mm) deep past cover mounting tabs (including pedestal). Enclosure cover dimensions are 21.5 in x 15.386 in (546 mm x 391 mm). NOTICE: This equipment is air-cooled. Mount in a location where the vented cover will not be blocked. 12 in (305 mm) of clearance in front of the vents is required. NOTICE: Power supply will hum slightly and internal relays will click while in use. Mount in a location where such noise is acceptable.
Dimensions
Enclosure: 21 in (533 mm) x 14.375 in (365 mm) x 4.088 in (104 mm) Cover: 21.5 in (546 mm) x 15.386 in (391 mm)
Construction
Enclosure: 16-gauge powder coated sheet metal. Cover: 16-gauge powder coated metal cover. Cover is attached using four philips-head screws.
Capacity
Enclosure can accomodate two processors or system interface devices and five wire landing boards (QS-WLB). Examples: 1 Processor and 1 System Interface or 2 Processors or 2 Interfaces
Line-Voltage Connections
Use copper wire only, supply conductors rated at 167 ºF (75 °C). Use supplied wire connections to connect to corresponding power supply harnesses.
Warranty
8 Year Limited Warranty. http://www.lutron.com/resiinfo
2 | Lutron®
24/7 Technical Support—800.523.9466
product specifications
03.09.11
369-381a
Low-Voltage Enclosure Dimensions and Mounting 14.375 (365) 13.285 (337)
Measurements shown as: in (mm)
7.750 (197)
Terminal Shield
Surface Mounting Pedestal (4x)
Line voltage wiring entry (non-IEC PELV / NEC® Class 2)
Power Supply DIN rail End Stop (5x)
Input Power Switch
-7°
+7° 18.0 (457)
21 (533)
0.312 (7.9)
20.0 (508)
0.430 (10.9) 0.624 (15.8)
11.5 (292)
www.lutron.com
PELV / Class 2 ONLY
Lutron® | 3
product specifications
369-381a
03.09.11
Low-Voltage Enclosure Configuration
L(+) N(-)
120 - 240 V Input / Entrada / Entrée
L(+) N(-)
24 V Output / Salida / Sortie
QSPS-DH-1-60
120 - 240 V Input / Entrada / Entrée
Power Supply QSPS-DH-1-60 (up to 2)
24 V Output / Salida / Sortie
QSPS-DH-1-60
22.5 - 25 V
22.5 - 25 V
HomeWorks QS Processor HQP6-2-120 (up to 2)
QS Wire Landing Board QS-WLB (up to 5, 1 included)
Power Draw Information Power Supply
Power Draw Units Supplied
QSPS-DH-1-60
75 PDU
Device
Power Draw Units Required (per device)
Processor HQP6-2-120
8 PDU
QSE-CI-NWK-E
2 PDU
QSE-IO
3 PDU
4 | Lutron®
24/7 Technical Support—800.523.9466
