6500 Series Installation Instructions - Dynalock
SERIES #6500 - DOUBLE GANG HIGH VISIBILITY PUSH PLATE
DynaLock
705 Emmett Street Bristol, CT 06010 Phone:(860)582-4761 Fax:(860)585-0338
INSTALLATION INSTRUCTIONS
OVERVIEW
The 6500 Series Pushplate mounts to a standard 2-gang electrical box. Illuminated display uses electroluminescent blue lamp which requires high voltage AC. An inverter is included to convert regulated 12 or 24 VDC (as specified) to the necessary AC voltage. The inverter must remain inside the box to which the pushplate is being mounted. Pushplate activates the switch when completely depressed. Sensitivity can be adjusted by altering the depth of the switch.
CAUTION! INVERTER PRODUCES HIGH VOLTAGE AC. READ ALL INSTRUCTIONS PRIOR TO INSTALLATION.
INSTALLATION STEPS 1. 2. 3. 4. 5.
Connect gray leads coming from the lamp to the white leads on inverter cube. Polarity not observed. Connect low voltage DC to red and black leads on inverter cube (see reverse). Connect switch wiring. See reverse for schematic according to style ordered. Make sure all wiring is clear of the four shoulder bolts. Mounting screws are accessed through the four holes on the front face of the pushplate. Using included Allen wrench, start threads on each screw. 6. Tighten mounting screws evenly by alternating each corner, until the faceplate is flush with the wall. EL LAMP LEADS 4-9/16”
13/16”
13/16”
1-1/8”
1”
4-1/2”
DynaLock MOUNTING SCREW ACCESS HOLE
PTD SWITCH FACEPLATE
SHOULDER BOLT MO1, MO2, AA1, AA2 SWITCH
MISCELLANEOUS Lamp Life: Indefinite. Optimal brightness - first 10,000 hours, continuous use. Field replacements available. Temperature Range: 15 to 120°F - Interior use only. 6500 MANUAL - FORM 6500-002
Page 1
10/06
SERIES #6500 - DOUBLE GANG HIGH VISIBILITY PUSH PLATE
DynaLock
705 Emmett Street Bristol, CT 06010 Phone:(860)582-4761 Fax:(860)585-0338
INSTALLATION INSTRUCTIONS
INVERTER WIRING WHITE WHITE AC OUT: WIRE TO GRAY LAMP LEADS (polarity not observed) Voltage: 220 VAC Frequency: 650 Hz
RED (+) BLACK (-)
• SWITCH DC VOLTAGE TO TURN LAMP ON AND OFF (NEVER SWITCH LAMP ON AC SIDE). • DO NOT APPLY POWER WITHOUT LAMP CONNECTED. • USE REGULATED DC POWER SUPPLY OR PLUG-IN ONLY.
5/8” 7/8”
DC IN: WIRE TO DC VOLTAGE (12 or 24VDC as specified) Current Draw: 30mA @ 12 or 24 VDC
1”
SWITCH WIRING SWITCH STYLE: MO1
SWITCH STYLE: AA1 BLACK
WHITE (NC) (C) (NO)
GREEN
SWITCH STYLE: PTD
(NC) (C)
RED
(NO)
YELLOW GRAY
YELLOW RED
YELLOW RED
SPDT MOMENTARY CONTACTS RATED 6 AMPS @ 125VAC
SPDT ALTERNATE-ACTION CONTACTS RATED 6 AMPS @ 125VAC
MOMENTARY TIME DELAYED CONTACTS RATED 10 AMPS @ 12OVAC PTD / FORM Z
SWITCH STYLE: MO2
SWITCH STYLE: AA2
TIME DELAY ADJUSTMENT
BLACK
WHITE (NC) (C) (NO) (NC) (C) (NO)
GREEN
(NC) (C)
RED
WHITE GREEN
(NO) (NC) (C) (NO)
6500 MANUAL - FORM 6500-002
BOTTOM VIEW
GRAY
YELLOW
TURN CW TO INCREASE TURN CCW TO DECREASE
GRAY
TIME DELAY ADJUSTMENT RANGE = 2 - 60 SECONDS
BLACK
RED
DPDT MOMENTARY CONTACTS RATED 6 AMPS @ 125VAC
YELLOW
TIME DELAY ADJUSTMENT KNOB
DPDT ALTERNATE-ACTION CONTACTS RATED 6 AMPS @ 125VAC Page 2
10/06
DynaLock
705 Emmett Street Bristol, CT 06010 Phone:(860)582-4761 Fax:(860)585-0338
INSTALLATION INSTRUCTIONS
OVERVIEW
The 6500 Series Pushplate mounts to a standard 2-gang electrical box. Illuminated display uses electroluminescent blue lamp which requires high voltage AC. An inverter is included to convert regulated 12 or 24 VDC (as specified) to the necessary AC voltage. The inverter must remain inside the box to which the pushplate is being mounted. Pushplate activates the switch when completely depressed. Sensitivity can be adjusted by altering the depth of the switch.
CAUTION! INVERTER PRODUCES HIGH VOLTAGE AC. READ ALL INSTRUCTIONS PRIOR TO INSTALLATION.
INSTALLATION STEPS 1. 2. 3. 4. 5.
Connect gray leads coming from the lamp to the white leads on inverter cube. Polarity not observed. Connect low voltage DC to red and black leads on inverter cube (see reverse). Connect switch wiring. See reverse for schematic according to style ordered. Make sure all wiring is clear of the four shoulder bolts. Mounting screws are accessed through the four holes on the front face of the pushplate. Using included Allen wrench, start threads on each screw. 6. Tighten mounting screws evenly by alternating each corner, until the faceplate is flush with the wall. EL LAMP LEADS 4-9/16”
13/16”
13/16”
1-1/8”
1”
4-1/2”
DynaLock MOUNTING SCREW ACCESS HOLE
PTD SWITCH FACEPLATE
SHOULDER BOLT MO1, MO2, AA1, AA2 SWITCH
MISCELLANEOUS Lamp Life: Indefinite. Optimal brightness - first 10,000 hours, continuous use. Field replacements available. Temperature Range: 15 to 120°F - Interior use only. 6500 MANUAL - FORM 6500-002
Page 1
10/06
SERIES #6500 - DOUBLE GANG HIGH VISIBILITY PUSH PLATE
DynaLock
705 Emmett Street Bristol, CT 06010 Phone:(860)582-4761 Fax:(860)585-0338
INSTALLATION INSTRUCTIONS
INVERTER WIRING WHITE WHITE AC OUT: WIRE TO GRAY LAMP LEADS (polarity not observed) Voltage: 220 VAC Frequency: 650 Hz
RED (+) BLACK (-)
• SWITCH DC VOLTAGE TO TURN LAMP ON AND OFF (NEVER SWITCH LAMP ON AC SIDE). • DO NOT APPLY POWER WITHOUT LAMP CONNECTED. • USE REGULATED DC POWER SUPPLY OR PLUG-IN ONLY.
5/8” 7/8”
DC IN: WIRE TO DC VOLTAGE (12 or 24VDC as specified) Current Draw: 30mA @ 12 or 24 VDC
1”
SWITCH WIRING SWITCH STYLE: MO1
SWITCH STYLE: AA1 BLACK
WHITE (NC) (C) (NO)
GREEN
SWITCH STYLE: PTD
(NC) (C)
RED
(NO)
YELLOW GRAY
YELLOW RED
YELLOW RED
SPDT MOMENTARY CONTACTS RATED 6 AMPS @ 125VAC
SPDT ALTERNATE-ACTION CONTACTS RATED 6 AMPS @ 125VAC
MOMENTARY TIME DELAYED CONTACTS RATED 10 AMPS @ 12OVAC PTD / FORM Z
SWITCH STYLE: MO2
SWITCH STYLE: AA2
TIME DELAY ADJUSTMENT
BLACK
WHITE (NC) (C) (NO) (NC) (C) (NO)
GREEN
(NC) (C)
RED
WHITE GREEN
(NO) (NC) (C) (NO)
6500 MANUAL - FORM 6500-002
BOTTOM VIEW
GRAY
YELLOW
TURN CW TO INCREASE TURN CCW TO DECREASE
GRAY
TIME DELAY ADJUSTMENT RANGE = 2 - 60 SECONDS
BLACK
RED
DPDT MOMENTARY CONTACTS RATED 6 AMPS @ 125VAC
YELLOW
TIME DELAY ADJUSTMENT KNOB
DPDT ALTERNATE-ACTION CONTACTS RATED 6 AMPS @ 125VAC Page 2
10/06
