Architectural Seals - Lorient UK
Instructions
Architectural Seals Fitting instructions Batwing® seals
LAS1206 Single Batwing®
LAS1007 Single Batwing®
12
LAS1010 Batwing®
LAS1212 Batwing®
2 - 4 mm gap between the door and the door stop to enable the door to close. Tight gaps will dislodge the seal from its position.
pushing it into the centre of the reveal.
5. Pull adhesive backing strips off both legs a little at a time, progressively pushing Batwing® into place.
It is essential to ensure that freshly painted surfaces are fully dry and cured before commencing installation.
1. Remove Batwing
from packaging and trim to length using snips. ®
2. Peel adhesive from both legs of the Batwing
12
4. Run finger down centre of the profile
Please note: Batwing® needs to have a
Please note: For single Batwing®
there are two preferred positions in the door frame, the flexible seal to be in the same alignment as the double Batwing®.
Important The product will not adhere to surfaces where silicone sealant has been applied.
®
approx 100mm.
15
LAS1015 Batwing®
15
Tools required Tape measure Pencil or marker Mitre saw or snips
3. Mount in the top corner, using a jointing method as tight as possible to ensure continuity of seal.
Please note: Recommendations as to
methods, use of materials and construction details are based on the experience and knowledge of Lorient and are given in good faith as a general guide and service to designers, contractors and manufacturers. Lorient reserves the right to make alterations or delete installation detail without prior notice.
Other Lorient products: Acoustic, smoke & fire seals Fire resistant glazing systems Fire resistant door hardware Air transfer grilles/ dampers Georgia Pacific doors
For further information about our products please visit our website
www.lorientgroup.com t: +44 (0)1626 834252 f: +44 (0)1626 833166 e: [email protected]
5DL3
Positive pressure tested gasketing materials for fire doors for application to hollow-metaltype fire doors rated up to 3 hours & woodtype fire doors rated up to 1-1.5 hours. CATEGORY J – Doors – gasketing that has been tested on a positive pressure fire door & frame but is not required for the door to obtain its fire rating. Category J gasketing does not negatively affect the rating on a positive pressure door.
Lorient Polyproducts Ltd Endeavour House Fairfax Road Heathfield Ind Estate Newton Abbot Devon TQ12 6UD UK
04/15
Architectural Seals Fitting instructions Batwing® seals
LAS1206 Single Batwing®
LAS1007 Single Batwing®
12
LAS1010 Batwing®
LAS1212 Batwing®
2 - 4 mm gap between the door and the door stop to enable the door to close. Tight gaps will dislodge the seal from its position.
pushing it into the centre of the reveal.
5. Pull adhesive backing strips off both legs a little at a time, progressively pushing Batwing® into place.
It is essential to ensure that freshly painted surfaces are fully dry and cured before commencing installation.
1. Remove Batwing
from packaging and trim to length using snips. ®
2. Peel adhesive from both legs of the Batwing
12
4. Run finger down centre of the profile
Please note: Batwing® needs to have a
Please note: For single Batwing®
there are two preferred positions in the door frame, the flexible seal to be in the same alignment as the double Batwing®.
Important The product will not adhere to surfaces where silicone sealant has been applied.
®
approx 100mm.
15
LAS1015 Batwing®
15
Tools required Tape measure Pencil or marker Mitre saw or snips
3. Mount in the top corner, using a jointing method as tight as possible to ensure continuity of seal.
Please note: Recommendations as to
methods, use of materials and construction details are based on the experience and knowledge of Lorient and are given in good faith as a general guide and service to designers, contractors and manufacturers. Lorient reserves the right to make alterations or delete installation detail without prior notice.
Other Lorient products: Acoustic, smoke & fire seals Fire resistant glazing systems Fire resistant door hardware Air transfer grilles/ dampers Georgia Pacific doors
For further information about our products please visit our website
www.lorientgroup.com t: +44 (0)1626 834252 f: +44 (0)1626 833166 e: [email protected]
5DL3
Positive pressure tested gasketing materials for fire doors for application to hollow-metaltype fire doors rated up to 3 hours & woodtype fire doors rated up to 1-1.5 hours. CATEGORY J – Doors – gasketing that has been tested on a positive pressure fire door & frame but is not required for the door to obtain its fire rating. Category J gasketing does not negatively affect the rating on a positive pressure door.
Lorient Polyproducts Ltd Endeavour House Fairfax Road Heathfield Ind Estate Newton Abbot Devon TQ12 6UD UK
04/15
