Bandit Bid Specifications - Model 65XP PTO 3-Point Hitch Unit
SPECIFICATIONS BANDIT MODEL 65XP PTO 3-POINT HITCH UNIT (6" DISC STYLE) PTO BRUSH BANDIT
SPECIFICATION Capacity: 6"
Measurements
Throat Opening: 6" x 12" Feed Rate: 80 FPM (1/4" chip) Noise Level: 80 decibels at 50 feet
Dimensions
Length (with infeed tray 6' 4" closed): Width: 4' 6"
Height: 7' 7" Weight: 1,550 pounds (approximate)
Engine
Options: Recommended 20-45 HP (540-1000 RPM)
PTO Options
Hitch: Category 1 (3/4" top pins & 7/8" bottom pins) Drive Shaft: 1 3/8" diameter "fatigue proof" steel drive jack shaft. (Note: drive shaft to connect unit to tractor is not included) Drive System: Drive for 540 RPM tractor PTO (Note: 1,000 RPM drive is optional) Suggested Tractor 20 to 45 horsepower Horsepower: Type: Pivoting
Feed System
Down Pressure Springs: (2) Yoke Sides: 3/8" plate steel Feed Wheels: (1) horizontal Feed Wheel Dimensions: 10 5/8" diameter x 11 1/2" wide Feed Wheel Teeth: 5 knife edge and 5 serrated Feed Wheel End Caps: Toothed to eliminate wrapping around shafts Number of Hydraulic Motors: 1 Displacement: 24
Torque at System Pressure: 7,680 in/lbs Attachment: Tapered fit coupling system Infeed Hopper Dimensions: 29" high x 42" Infeed Thickness: 10 gauge Infeed Tray: 30" folding infeed tray Also to include a safety control bar located on three sides of the infeed hopper to allow actuation of feed wheels forward/neutral/reverse. The control bar is supported by (2) 1" threaded rods. Feed Roller to End of Infeed 66" Table: Infeed Slope: 3 degrees Bottom Clean Out Door: Included
Cutting System Style: Disc Dimensions: 26" diameter x 3/4" thick RPM: 1950 Knife Pockets: 2 Knives: (2) 1/2" x 4" x 7 1/4" dual edge Knife Bolts: (3) 1/2" grade 8 bolts Thrower: (2) 3" x 4" x 12 1/4" (cupped) Anvil: 3 bolt, 4 sided anvil (1/2" x 3" x 6") Chipper Shaft: 2" diameter Chipper Bearings: (2) 2" Flange mounted greasable bearings Chipper Hood: Must fold back, to access knives and disc
Construction Chipper Base (Front): 1/4" Chipper Base (Back): 1/4" Belly Band: 3/16" Right Throat Side: 3/8" Left Throat Side: 3/8" Throat Bottom: 1/4" Chipper Hood: 10 gauge
Hydraulic System Type: Open Center Filtration: 3 Micron return, 100 micron suction Pump: Casappa (gear style) Relief Pressure: 1800 PSI Hydraulic Hoses: 1/2" & 5/8" single and double braid Hydraulic Hose Burst 12,000 PSI Pressure:
Discharge Swivel: 360 degree manual swivel discharge (tool-less) Deflector: 12" adjustable chip deflector (4 adjustments are provided) Hand Crank Swivel Discharge: Optional
Hand Crank Height Discharge: Optional
Hydraulic Tank Capacity: 6 gallons Mount: Rubber Shock Mounted Magnetic Drain Plug: Included Rochester Sight Gauge: Optional Lockable Filler Caps: Optional
Paint Colors: Choose from: Bandit yellow, Caterpillar yellow, Alert orange, green, black, or white
Battery / Tool Boxes Tool Box: Optional
Safety Features Safety Features: Guards covering all moving parts Disc lock bar Wooden pusher paddle Mechanical spring lock pin (2) Last chance pull cables (Patented) Safety Control Bar * Bandit Industries, Inc. reserves the right to modify any and all specifications as it see fit, without notice.
SPECIFICATION Capacity: 6"
Measurements
Throat Opening: 6" x 12" Feed Rate: 80 FPM (1/4" chip) Noise Level: 80 decibels at 50 feet
Dimensions
Length (with infeed tray 6' 4" closed): Width: 4' 6"
Height: 7' 7" Weight: 1,550 pounds (approximate)
Engine
Options: Recommended 20-45 HP (540-1000 RPM)
PTO Options
Hitch: Category 1 (3/4" top pins & 7/8" bottom pins) Drive Shaft: 1 3/8" diameter "fatigue proof" steel drive jack shaft. (Note: drive shaft to connect unit to tractor is not included) Drive System: Drive for 540 RPM tractor PTO (Note: 1,000 RPM drive is optional) Suggested Tractor 20 to 45 horsepower Horsepower: Type: Pivoting
Feed System
Down Pressure Springs: (2) Yoke Sides: 3/8" plate steel Feed Wheels: (1) horizontal Feed Wheel Dimensions: 10 5/8" diameter x 11 1/2" wide Feed Wheel Teeth: 5 knife edge and 5 serrated Feed Wheel End Caps: Toothed to eliminate wrapping around shafts Number of Hydraulic Motors: 1 Displacement: 24
Torque at System Pressure: 7,680 in/lbs Attachment: Tapered fit coupling system Infeed Hopper Dimensions: 29" high x 42" Infeed Thickness: 10 gauge Infeed Tray: 30" folding infeed tray Also to include a safety control bar located on three sides of the infeed hopper to allow actuation of feed wheels forward/neutral/reverse. The control bar is supported by (2) 1" threaded rods. Feed Roller to End of Infeed 66" Table: Infeed Slope: 3 degrees Bottom Clean Out Door: Included
Cutting System Style: Disc Dimensions: 26" diameter x 3/4" thick RPM: 1950 Knife Pockets: 2 Knives: (2) 1/2" x 4" x 7 1/4" dual edge Knife Bolts: (3) 1/2" grade 8 bolts Thrower: (2) 3" x 4" x 12 1/4" (cupped) Anvil: 3 bolt, 4 sided anvil (1/2" x 3" x 6") Chipper Shaft: 2" diameter Chipper Bearings: (2) 2" Flange mounted greasable bearings Chipper Hood: Must fold back, to access knives and disc
Construction Chipper Base (Front): 1/4" Chipper Base (Back): 1/4" Belly Band: 3/16" Right Throat Side: 3/8" Left Throat Side: 3/8" Throat Bottom: 1/4" Chipper Hood: 10 gauge
Hydraulic System Type: Open Center Filtration: 3 Micron return, 100 micron suction Pump: Casappa (gear style) Relief Pressure: 1800 PSI Hydraulic Hoses: 1/2" & 5/8" single and double braid Hydraulic Hose Burst 12,000 PSI Pressure:
Discharge Swivel: 360 degree manual swivel discharge (tool-less) Deflector: 12" adjustable chip deflector (4 adjustments are provided) Hand Crank Swivel Discharge: Optional
Hand Crank Height Discharge: Optional
Hydraulic Tank Capacity: 6 gallons Mount: Rubber Shock Mounted Magnetic Drain Plug: Included Rochester Sight Gauge: Optional Lockable Filler Caps: Optional
Paint Colors: Choose from: Bandit yellow, Caterpillar yellow, Alert orange, green, black, or white
Battery / Tool Boxes Tool Box: Optional
Safety Features Safety Features: Guards covering all moving parts Disc lock bar Wooden pusher paddle Mechanical spring lock pin (2) Last chance pull cables (Patented) Safety Control Bar * Bandit Industries, Inc. reserves the right to modify any and all specifications as it see fit, without notice.
