Blackberry Torch 9800 Replacing rear camera
Blackberry Torch 9800 Replacing rear camera
Blackberry Torch 9800 Replacing rear camera Written By: 0delete
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Blackberry Torch 9800 Replacing rear camera
INTRODUCTION This guide will help you replace a not working camera on a Blackberry Torch 9800 phone. Making any physical change to this phone will void the warranty.
TOOLS: T7 Torx Screwdriver (1) iFixit Opening Tools (1) Flathead Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Blackberry Torch 9800 Replacing rear camera
Step 1 — Replacing rear camera
Remove the back cover and the battery.
Remove the four exposed screws using a T7 screwdriver.
Warning: Removing the top right screw (with the blue cover) will void the warranty.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Blackberry Torch 9800 Replacing rear camera
Step 2
Remove the side trim using the plastic opening tool.
When loose, push the top backwards and the bottom forwards to remove.
Step 3
Two new screws have been exposed near the top of the back.
Remove the two screws using the T7 screwdriver.
Remove the back panel using the plastic opening tool.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Blackberry Torch 9800 Replacing rear camera
Step 4
Carefully use flathead screwdriver to free camera sensor.
Wiggle on the right and left sides, not the top and bottom sides.
Step 5
To install the new camera sensor, place in slot. Reassemble phone by doing steps 1-3 in reverse order.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Blackberry Torch 9800 Replacing rear camera This document was last generated on 2017-06-17 10:57:26 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Blackberry Torch 9800 Replacing rear camera Written By: 0delete
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Blackberry Torch 9800 Replacing rear camera
INTRODUCTION This guide will help you replace a not working camera on a Blackberry Torch 9800 phone. Making any physical change to this phone will void the warranty.
TOOLS: T7 Torx Screwdriver (1) iFixit Opening Tools (1) Flathead Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Blackberry Torch 9800 Replacing rear camera
Step 1 — Replacing rear camera
Remove the back cover and the battery.
Remove the four exposed screws using a T7 screwdriver.
Warning: Removing the top right screw (with the blue cover) will void the warranty.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Blackberry Torch 9800 Replacing rear camera
Step 2
Remove the side trim using the plastic opening tool.
When loose, push the top backwards and the bottom forwards to remove.
Step 3
Two new screws have been exposed near the top of the back.
Remove the two screws using the T7 screwdriver.
Remove the back panel using the plastic opening tool.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Blackberry Torch 9800 Replacing rear camera
Step 4
Carefully use flathead screwdriver to free camera sensor.
Wiggle on the right and left sides, not the top and bottom sides.
Step 5
To install the new camera sensor, place in slot. Reassemble phone by doing steps 1-3 in reverse order.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Blackberry Torch 9800 Replacing rear camera This document was last generated on 2017-06-17 10:57:26 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
