Blackberry Torch 9810 Rear Facing Camera Replacement
Blackberry Torch 9810 Rear Facing Camera Replacement
Blackberry Torch 9810 Rear Facing Camera Replacement After finishing your guide, your broken camera should not be a problem!
Written By: Jocelyn Adorno
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
TOOLS: T4 Torx Screwdriver (1) iFixit Opening Tools (1) T6 Torx Screwdriver (1) Phillips #0 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
Step 1 — Remove Cover
Remove the back cover of the phone
Step 2 — Remove Battery
Remove the battery
Our phone did not come with a battery. This is where it would be located.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
Step 3 — Unscrew Screws
Unscrew the four screws using the T6 screw driver
If you remove the screw in red, you void the warranty! Step 4 — Wiggle Wiggle
Remove front silver trim by using plastic opening tools and wiggle it off.
This is a little difficult to remove. Pull the bottom upward and pull the top downward. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
Step 5 — Smaller Screws That Must Go
Once you remove the rim cover, you should find two more screws on the top. Unscrew them using the T6 screw driver.
Step 6 — Camera Sensor
Use the Phillip screw driver to wiggle the camera sensor out.
Carefully remove this To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement This document was last generated on 2017-06-19 07:38:19 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement After finishing your guide, your broken camera should not be a problem!
Written By: Jocelyn Adorno
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
TOOLS: T4 Torx Screwdriver (1) iFixit Opening Tools (1) T6 Torx Screwdriver (1) Phillips #0 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
Step 1 — Remove Cover
Remove the back cover of the phone
Step 2 — Remove Battery
Remove the battery
Our phone did not come with a battery. This is where it would be located.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
Step 3 — Unscrew Screws
Unscrew the four screws using the T6 screw driver
If you remove the screw in red, you void the warranty! Step 4 — Wiggle Wiggle
Remove front silver trim by using plastic opening tools and wiggle it off.
This is a little difficult to remove. Pull the bottom upward and pull the top downward. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement
Step 5 — Smaller Screws That Must Go
Once you remove the rim cover, you should find two more screws on the top. Unscrew them using the T6 screw driver.
Step 6 — Camera Sensor
Use the Phillip screw driver to wiggle the camera sensor out.
Carefully remove this To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Blackberry Torch 9810 Rear Facing Camera Replacement This document was last generated on 2017-06-19 07:38:19 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
