bled5 installation instructions - RAB Lighting
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
BLED5 Square
IMPORTANT
BLEDR5 Round
BLED2X5 Square
BLEDR2X5 Round
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING:
Make certain power is OFF before installing or maintaining fixture. No user servicable parts inside.
MOUNTING PLATE
LOCATION
1. The Bollard should be mounted to a firm level surface.
Assemble fixture(s) to bollard before mounting the Bollard to the Mounting Plate.
2. Anchor bolts may be used in new concrete installations. Use the template provided.
1. Place the Mounting Plate over Anchor Bolts.
3. For all other applications use anchors suitable for the mounting surface.
2. Use four Leveling Screws or shims to level the Mounting Plate.
ANCHOR BOLTS INSTALLATION
3. Tighten assembly using the washers, lockwashers and nuts provided.
CAUTION: Install according to all applicable local codes. 1. Install two Anchor Bolts in concrete foundation (by others) using the template provided. Mounting Plate may also be used as the template. Anchor Bolts should protrude no more than 3”.
4. Make sure supply leads extend far enough to make fixture connections. 5. Slide Gasket down around the bottom of the Mounting Plate. 6. Use the four screws to mount the Bollard to the Mounting Plate. Tighten securely. Bollard Leveling Screws
Anchor Bolts
Gasket
Mounting Plate Mounting Screws Concrete
Anchor Bolts
Conduit
Mounting Plate
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
MOUNTING FIXTURES
For BLED5 & BLEDR5 the window is available on one side of Bollard. Secure Bollard before installing the housing. 1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets. Fixture may hang from the tether while installing. 2. Place Bollard Gasket and Mounting Plate over recessed box. 3. Attach Mounting Plate with supplied Mounting Plate Screws. 4. Pull supply wires from box through mounting plate and wire fixture as shown in the wiring section. 5. Check Housing Gasket. It should remain firmly around the inside of the Housing. 6. Align Housing to Mounting Plate. 7. Make sure all gaskets are properly seated. Tighten Housing Screws. 8. Secure the Cap Gasket and tighten the Bollard Cap with supplied screws. Bollard Cap
Cap Gasket
Bollard Cap
Bollard Gasket Housing Housing screws
Mounting Plate
Cap Gasket
Bollard
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
MOUNTING FIXTURES
For BLED2x5 & BLEDR2x5, cutouts are provided on both sides of Bollard. Secure Bollard before installing the housings. 1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets. Fixture may hang from the tether while installing. 2. Place Bollard Gasket and Mounting Plate over cut out on Bollard. 3. Attach Mounting Plate with supplied mounting plate screws. 4. Pull supply wires from bollard through mounting plate and wire fixture as shown in the wiring section. 5. Check Housing Gasket. It should remain firmly around the inside of the Housing. 6. Align Housing to Mounting Plate. 7. Make sure all gaskets are properly seated. Tighten Housing Screws. 8. Follow same steps for second fixture. 9. Secure the Cap Gasket and tighten the Bollard Cap with provided screws. Bollard Cap Bollard
Cap Gasket
Bollard Gasket
Housing
Mounting Plate
Bollard Gasket
Cap Gasket
Mounting Plate
Bollard Cap
Housing screws
Bollard
Housing Gaskets
HousingScrews
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
WIRING
Universal voltage driver permits operation at 120V to 277VAC, 50 or 60Hz 1. Connect the bare copper Ground wire from fixture to supply ground. 2. Connect the BLACK fixture lead to the (+) LINE supply lead. 3. Connect the WHITE fixture lead to the (-) COMMON supply lead.
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized. 1. Clean glass lens with non-abrasive glass cleaning solution 2. Do not open fixture to clean the LED.
TROUBLESHOOTING 1. Check that the line voltage at fixture is correct. Refer to wiring directions. 2. Is the fixture grounded properly? 3. Is the photocell is functioning properly (if used)?
PHOTOCELL INSTALLATION Photocell may be wired in the field. Apply weatherproof silicone sealant to all plugs and unused conduit entries. 1. Install photocell and wire as per diagram. 2. Use photocell rated for your supply voltage. RED
BLACK
WHITE BLACK
“COM” WHITE
PHOTOCELL
PHOTOCELL
BLED5 Cool LED Square Steplight
DRIVER WP2FC
ACCESSORIES Bollard base: Bollard base Retro kit: Suffix “Y” = Suffix “N” =
BOLBASE BOLBASE RETRO
Warm 3000K LED Neutral 4000K LED,
SLED Round: US pat. D612,974, CN: ZL201030129138.4, TW: pat. D140455, CA: D RAB Lighting Inc. SLED Square:.US pat. D612,975, CN: ZL201030129140.1, TW: pat. D140456, CA: D RAB Lighting Inc.
BLEDR5 Cool LED Round Steplight
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
BLED5N Neutral LED Square Steplight
BLEDR5N Neutral LED Round Steplight
BLED5Y Warm LED Square Steplight
BLEDR5Y Warm LED Round Steplight
Easy Installation & Product Help ©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
BLED5-IN-0814
Tech Help Line Call our experts 888 RAB-1000
rabweb.com Visit our website for product info
email Answered promptly [email protected]
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ANCHOR BOLT TEMPLATE FOR BLED BOLLARD
Confirm dimensions before using as a template. If possible use the actual mounting plate as your template.
BLED5 Square
IMPORTANT
BLEDR5 Round
BLED2X5 Square
BLEDR2X5 Round
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING:
Make certain power is OFF before installing or maintaining fixture. No user servicable parts inside.
MOUNTING PLATE
LOCATION
1. The Bollard should be mounted to a firm level surface.
Assemble fixture(s) to bollard before mounting the Bollard to the Mounting Plate.
2. Anchor bolts may be used in new concrete installations. Use the template provided.
1. Place the Mounting Plate over Anchor Bolts.
3. For all other applications use anchors suitable for the mounting surface.
2. Use four Leveling Screws or shims to level the Mounting Plate.
ANCHOR BOLTS INSTALLATION
3. Tighten assembly using the washers, lockwashers and nuts provided.
CAUTION: Install according to all applicable local codes. 1. Install two Anchor Bolts in concrete foundation (by others) using the template provided. Mounting Plate may also be used as the template. Anchor Bolts should protrude no more than 3”.
4. Make sure supply leads extend far enough to make fixture connections. 5. Slide Gasket down around the bottom of the Mounting Plate. 6. Use the four screws to mount the Bollard to the Mounting Plate. Tighten securely. Bollard Leveling Screws
Anchor Bolts
Gasket
Mounting Plate Mounting Screws Concrete
Anchor Bolts
Conduit
Mounting Plate
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
MOUNTING FIXTURES
For BLED5 & BLEDR5 the window is available on one side of Bollard. Secure Bollard before installing the housing. 1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets. Fixture may hang from the tether while installing. 2. Place Bollard Gasket and Mounting Plate over recessed box. 3. Attach Mounting Plate with supplied Mounting Plate Screws. 4. Pull supply wires from box through mounting plate and wire fixture as shown in the wiring section. 5. Check Housing Gasket. It should remain firmly around the inside of the Housing. 6. Align Housing to Mounting Plate. 7. Make sure all gaskets are properly seated. Tighten Housing Screws. 8. Secure the Cap Gasket and tighten the Bollard Cap with supplied screws. Bollard Cap
Cap Gasket
Bollard Cap
Bollard Gasket Housing Housing screws
Mounting Plate
Cap Gasket
Bollard
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
MOUNTING FIXTURES
For BLED2x5 & BLEDR2x5, cutouts are provided on both sides of Bollard. Secure Bollard before installing the housings. 1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets. Fixture may hang from the tether while installing. 2. Place Bollard Gasket and Mounting Plate over cut out on Bollard. 3. Attach Mounting Plate with supplied mounting plate screws. 4. Pull supply wires from bollard through mounting plate and wire fixture as shown in the wiring section. 5. Check Housing Gasket. It should remain firmly around the inside of the Housing. 6. Align Housing to Mounting Plate. 7. Make sure all gaskets are properly seated. Tighten Housing Screws. 8. Follow same steps for second fixture. 9. Secure the Cap Gasket and tighten the Bollard Cap with provided screws. Bollard Cap Bollard
Cap Gasket
Bollard Gasket
Housing
Mounting Plate
Bollard Gasket
Cap Gasket
Mounting Plate
Bollard Cap
Housing screws
Bollard
Housing Gaskets
HousingScrews
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
WIRING
Universal voltage driver permits operation at 120V to 277VAC, 50 or 60Hz 1. Connect the bare copper Ground wire from fixture to supply ground. 2. Connect the BLACK fixture lead to the (+) LINE supply lead. 3. Connect the WHITE fixture lead to the (-) COMMON supply lead.
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized. 1. Clean glass lens with non-abrasive glass cleaning solution 2. Do not open fixture to clean the LED.
TROUBLESHOOTING 1. Check that the line voltage at fixture is correct. Refer to wiring directions. 2. Is the fixture grounded properly? 3. Is the photocell is functioning properly (if used)?
PHOTOCELL INSTALLATION Photocell may be wired in the field. Apply weatherproof silicone sealant to all plugs and unused conduit entries. 1. Install photocell and wire as per diagram. 2. Use photocell rated for your supply voltage. RED
BLACK
WHITE BLACK
“COM” WHITE
PHOTOCELL
PHOTOCELL
BLED5 Cool LED Square Steplight
DRIVER WP2FC
ACCESSORIES Bollard base: Bollard base Retro kit: Suffix “Y” = Suffix “N” =
BOLBASE BOLBASE RETRO
Warm 3000K LED Neutral 4000K LED,
SLED Round: US pat. D612,974, CN: ZL201030129138.4, TW: pat. D140455, CA: D RAB Lighting Inc. SLED Square:.US pat. D612,975, CN: ZL201030129140.1, TW: pat. D140456, CA: D RAB Lighting Inc.
BLEDR5 Cool LED Round Steplight
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
BLED5N Neutral LED Square Steplight
BLEDR5N Neutral LED Round Steplight
BLED5Y Warm LED Square Steplight
BLEDR5Y Warm LED Round Steplight
Easy Installation & Product Help ©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
BLED5-IN-0814
Tech Help Line Call our experts 888 RAB-1000
rabweb.com Visit our website for product info
email Answered promptly [email protected]
BLED5 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ANCHOR BOLT TEMPLATE FOR BLED BOLLARD
Confirm dimensions before using as a template. If possible use the actual mounting plate as your template.
