CABINET/SWIPE ON/OFF SENSOR SWITCH
Installation instructions
CABINET/SWIPE ON/OFF SENSOR SWITCH CODE: SE40516
IMPORTANT: please read these instructions before commencing installation and retain for future reference.
Tools required
Components
1 x self adhesive Pad
1 x IR Sensor Switch plus 6 port JB4 block
2 x screws
1 x Fitting Instructions
14mm screw Bit
Power Drill
Important safety information Please read these instructions carefully before attempting to install this product. It is advisable to keep these instructions in a safe place for further reference. We recommend that you consult a qualified electrician. All electrical installations must be carried out in accordance with current IEE wiring regulations (BS7671). these products must not be modified, if any modifications are made, it may invalidate the warranty and may render the product unsafe. This product is for indoor use only.
• If in doubt installation must be carried out by a qualified electrician. • Install on smooth flat surface(s) only. • Do not exceed or stretch the cable length of each LED wire. • The detection range of the IR sensor is between 5cm and 10cm. • This type of IR switch is an exclusive design for Class III insulation appliance. Important notes: When the IR sensor is surface mounted, the face of the fitting (containing the detector) must be kept parallel with the edge of the installation surface. If you are using double side adhesive ONLY to fix the fitting, the hickness of the tape mst be more than 1.6mm for it to be effective.
Safety instructions 1. Before commencing installation or maintenance, isolate the main electrical supply for the appropriate circuit at the fuse board. 2. This product is only suitable for connecting to a 240V 50Hz supply. The light should be mounted onto a secure surface. 3. The maximum wattage allowance of the IR sensor is 15W for 12V products or 30W for 24V products. 4. suitable for furniture lighting.
Waste Electrical & Electronic Equipment (WEEE) The Symbol on the product, or on the document accompanying the product, the crossed out wheelie bin symbol, indicated that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic waste.
5. class III safety extra low voltage (sElV)
CABINET/SWIPE ON/OFF SENSOR SWITCH CODE: SE40516 Installation instructions this product can be installed two ways: Ensure the mains power is disconnected prior to commencing installation. Method 1 - Recessing: 1. Drill a hole with a diametre of 14.5mm. 2. Attach the plastic accessory included onto the top of the fitting to make the fitting suitable to be recessed. 3. Ensure the input cable passes through the installation hole. Method 2 - Surface Mounting: 1. Use the screws and/or the double sided adhesive pad included to fix the fitting to the installation surface. 2. Ensure the input and output cables are kept close to the installation surface.
This unit has 2 functions; Bistable & Monostable To change the function of the sensor press the 'mode change button' for more than 3 seconds. This should be done whilst the unit is connected to the mains power.
The above diagram shows how the sensor is integrated into your lighting run. 1. Connect the output wire into the distributor block on the driver. 2. Connect the input wire to the 6 way distributor block provided with the sensor. 3. All lights are to be connected to the remaining 5 ports on the block to which the sensor is connected.
Voltage Input
Voltage Output
The button can be found on the back of the fitting (please see diagram below). Bistable function: When the target object is in the detecting range once, the lamp switches off (for example the swipe of hand past the sensor). When the target object is in the detecting range a second time, the lamp will be switch on. The unit will continue to work in such a cycle. Continued operation won’t cause unwanted action. Detection range in this mode: Effective range: ≤5cm Ineffective range: ≥16cm The actual detection range is between 5cm and 16cm according to different sensors. f the IR sensor detector is blocked by other non transparent objects, there will be different Max. detecting distance, for instance; the detecting distance caused by a human hand is about 5cm.
Monostable function: When the target object is in the detecting range, the lamp switches off. When the target object is out of the detecting range, the lamp switches on (for example a cabinet door infront of the sensor). Continued operation won’t cause unwanted action.
Maintenance & Care • Ensure that the power is disconnected prior to cleaning. • To keep the finish of this product, wipe over with soft cloth periodically. • Do not use harsh chemical solvents, it may dis-colour or damage the finish.
Unit 7 Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustration purposes only, Sensio has the right to change any information without prior notice. Make sure you check all hole cut outs before work commences.
63mm
CABINET/SWIPE ON/OFF SENSOR SWITCH CODE: SE40516
IMPORTANT: please read these instructions before commencing installation and retain for future reference.
Tools required
Components
1 x self adhesive Pad
1 x IR Sensor Switch plus 6 port JB4 block
2 x screws
1 x Fitting Instructions
14mm screw Bit
Power Drill
Important safety information Please read these instructions carefully before attempting to install this product. It is advisable to keep these instructions in a safe place for further reference. We recommend that you consult a qualified electrician. All electrical installations must be carried out in accordance with current IEE wiring regulations (BS7671). these products must not be modified, if any modifications are made, it may invalidate the warranty and may render the product unsafe. This product is for indoor use only.
• If in doubt installation must be carried out by a qualified electrician. • Install on smooth flat surface(s) only. • Do not exceed or stretch the cable length of each LED wire. • The detection range of the IR sensor is between 5cm and 10cm. • This type of IR switch is an exclusive design for Class III insulation appliance. Important notes: When the IR sensor is surface mounted, the face of the fitting (containing the detector) must be kept parallel with the edge of the installation surface. If you are using double side adhesive ONLY to fix the fitting, the hickness of the tape mst be more than 1.6mm for it to be effective.
Safety instructions 1. Before commencing installation or maintenance, isolate the main electrical supply for the appropriate circuit at the fuse board. 2. This product is only suitable for connecting to a 240V 50Hz supply. The light should be mounted onto a secure surface. 3. The maximum wattage allowance of the IR sensor is 15W for 12V products or 30W for 24V products. 4. suitable for furniture lighting.
Waste Electrical & Electronic Equipment (WEEE) The Symbol on the product, or on the document accompanying the product, the crossed out wheelie bin symbol, indicated that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic waste.
5. class III safety extra low voltage (sElV)
CABINET/SWIPE ON/OFF SENSOR SWITCH CODE: SE40516 Installation instructions this product can be installed two ways: Ensure the mains power is disconnected prior to commencing installation. Method 1 - Recessing: 1. Drill a hole with a diametre of 14.5mm. 2. Attach the plastic accessory included onto the top of the fitting to make the fitting suitable to be recessed. 3. Ensure the input cable passes through the installation hole. Method 2 - Surface Mounting: 1. Use the screws and/or the double sided adhesive pad included to fix the fitting to the installation surface. 2. Ensure the input and output cables are kept close to the installation surface.
This unit has 2 functions; Bistable & Monostable To change the function of the sensor press the 'mode change button' for more than 3 seconds. This should be done whilst the unit is connected to the mains power.
The above diagram shows how the sensor is integrated into your lighting run. 1. Connect the output wire into the distributor block on the driver. 2. Connect the input wire to the 6 way distributor block provided with the sensor. 3. All lights are to be connected to the remaining 5 ports on the block to which the sensor is connected.
Voltage Input
Voltage Output
The button can be found on the back of the fitting (please see diagram below). Bistable function: When the target object is in the detecting range once, the lamp switches off (for example the swipe of hand past the sensor). When the target object is in the detecting range a second time, the lamp will be switch on. The unit will continue to work in such a cycle. Continued operation won’t cause unwanted action. Detection range in this mode: Effective range: ≤5cm Ineffective range: ≥16cm The actual detection range is between 5cm and 16cm according to different sensors. f the IR sensor detector is blocked by other non transparent objects, there will be different Max. detecting distance, for instance; the detecting distance caused by a human hand is about 5cm.
Monostable function: When the target object is in the detecting range, the lamp switches off. When the target object is out of the detecting range, the lamp switches on (for example a cabinet door infront of the sensor). Continued operation won’t cause unwanted action.
Maintenance & Care • Ensure that the power is disconnected prior to cleaning. • To keep the finish of this product, wipe over with soft cloth periodically. • Do not use harsh chemical solvents, it may dis-colour or damage the finish.
Unit 7 Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustration purposes only, Sensio has the right to change any information without prior notice. Make sure you check all hole cut outs before work commences.
63mm
