Cobra SPX 5300 Display Screen Replacement
Cobra SPX 5300 Display Screen Replacement
Cobra SPX 5300 Display Screen Replacement Replace the screen display of your Cobra SPX 5300 Radar Laser Detector.
Written By: Fanny Auad
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Cobra SPX 5300 Display Screen Replacement
INTRODUCTION If you are having difficulties looking at the display screen of your Cobra SPX 5300 this guide will walk you through its replacement.
TOOLS: Phillips #0 Screwdriver (1) Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Cobra SPX 5300 Display Screen Replacement
Step 1 — Windshield Bracket Mount
Remove the four 9.5 mm Phillips #0 screws from the back of the device.
Step 2
Pull the black plastic back case off of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Cobra SPX 5300 Display Screen Replacement
Step 3
Lift up the motherboard and lay it flat next to the device.
Be careful not to sever the wires. The buttonboard is connected to the motherboard by the wires.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the windshield bracket mount.
Page 4 of 7
Cobra SPX 5300 Display Screen Replacement
Step 5 — Buttonboard
Remove the four 4.8 mm Phillips #00 screws from the buttonboard.
Lift buttonboard to expose silver button plate.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 7
Cobra SPX 5300 Display Screen Replacement
Step 7 — Buttons
Remove the silver button plate by gripping one of the corners and pulling up.
Step 8 — Display Screen
Lift the front black plastic display screen.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 06:32:11 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Cobra SPX 5300 Display Screen Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
Cobra SPX 5300 Display Screen Replacement Replace the screen display of your Cobra SPX 5300 Radar Laser Detector.
Written By: Fanny Auad
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Cobra SPX 5300 Display Screen Replacement
INTRODUCTION If you are having difficulties looking at the display screen of your Cobra SPX 5300 this guide will walk you through its replacement.
TOOLS: Phillips #0 Screwdriver (1) Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Cobra SPX 5300 Display Screen Replacement
Step 1 — Windshield Bracket Mount
Remove the four 9.5 mm Phillips #0 screws from the back of the device.
Step 2
Pull the black plastic back case off of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Cobra SPX 5300 Display Screen Replacement
Step 3
Lift up the motherboard and lay it flat next to the device.
Be careful not to sever the wires. The buttonboard is connected to the motherboard by the wires.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the windshield bracket mount.
Page 4 of 7
Cobra SPX 5300 Display Screen Replacement
Step 5 — Buttonboard
Remove the four 4.8 mm Phillips #00 screws from the buttonboard.
Lift buttonboard to expose silver button plate.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 7
Cobra SPX 5300 Display Screen Replacement
Step 7 — Buttons
Remove the silver button plate by gripping one of the corners and pulling up.
Step 8 — Display Screen
Lift the front black plastic display screen.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 06:32:11 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Cobra SPX 5300 Display Screen Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
