Disassembling Garmin Nuvi 1200 Logic Board
Disassembling Garmin Nuvi 1200 Logic Board
Disassembling Garmin Nuvi 1200 Logic Board Removing the Logic Board from a Garmin Nuvi 1200
Written By: Zachary Landau
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Disassembling Garmin Nuvi 1200 Logic Board
INTRODUCTION This guide shows how to fully disassemble a Garmin Nuvi 1200 to replace the logic board.
TOOLS: Spudger (1) T5 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Disassembling Garmin Nuvi 1200 Logic Board
Step 1 — Logic Board
Remove to sticker on the back of the unit and then remove the two T5 scremws once this is done use a spudger to carefully pry off the silver cover.
Once the tool is inserted it can slide around the entire device.
Step 2
Remove four small T5 torx screws.
© iFixit — CC BY-NC-SA
www.iFixit.com
Be gentle, the screws are easily stripped.
Page 3 of 5
Disassembling Garmin Nuvi 1200 Logic Board
Step 3
Lift cover off of unit.
Be careful not to lose small rubber piece on the bottom right corner.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Disconnect ribbon cable from logic board.
Page 4 of 5
Disassembling Garmin Nuvi 1200 Logic Board
Step 5
Remove two T5 torx screws holding down logic board.
Disconnect battery.
Gently lift the logic board out of the unit
Step 6
Be careful not to damage the battery connector on the top of the unit.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-19 02:23:08 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Disassembling Garmin Nuvi 1200 Logic Board Removing the Logic Board from a Garmin Nuvi 1200
Written By: Zachary Landau
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Disassembling Garmin Nuvi 1200 Logic Board
INTRODUCTION This guide shows how to fully disassemble a Garmin Nuvi 1200 to replace the logic board.
TOOLS: Spudger (1) T5 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Disassembling Garmin Nuvi 1200 Logic Board
Step 1 — Logic Board
Remove to sticker on the back of the unit and then remove the two T5 scremws once this is done use a spudger to carefully pry off the silver cover.
Once the tool is inserted it can slide around the entire device.
Step 2
Remove four small T5 torx screws.
© iFixit — CC BY-NC-SA
www.iFixit.com
Be gentle, the screws are easily stripped.
Page 3 of 5
Disassembling Garmin Nuvi 1200 Logic Board
Step 3
Lift cover off of unit.
Be careful not to lose small rubber piece on the bottom right corner.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Disconnect ribbon cable from logic board.
Page 4 of 5
Disassembling Garmin Nuvi 1200 Logic Board
Step 5
Remove two T5 torx screws holding down logic board.
Disconnect battery.
Gently lift the logic board out of the unit
Step 6
Be careful not to damage the battery connector on the top of the unit.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-19 02:23:08 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
