DM-1e Spec - Ofna

IMPORTANT-READ THIS BEFORE RUNNING

1.Before Starting •If you are under 18 please read manual (with a parent, guardian or a responsible adult if necessary).

2.While Operating •Any running area you choose must be dry. Do not run car near any water or wet dirt. •Do not run on public streets. It is very easy to have the car run over or be damaged by hitting the curb. •Do not operate the car in tight confined space. The car is very fast and will easily hit something. •Do not run near people or animals. The car is very fast and could easily hit someone if you are not an expert driver.

•Do not operate the car at night. You will not be able to drive it safely.

3.Before Operating •Make sure that all screws and nuts are properly tightened.

•Radio-Check battery life before running the car. If the radio does not have full control of the car with steering and/or throttle/brake, do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property.

•Please confirm the neutral throttle trigger position.

4.Check Your Car After Running •Turn OFF receiver first, then turn OFF transmitter. This will prevent the car from losing control. •After running radio controlled car , it is necessary to perform routine maintenance.

5.Battery Safety •Please be careful when handling the battery. It will be hot after running. If the wire is frayed, a short circuit can cause a fire.

OVERVIEW Components

Radio Control Car

Parts Bag

TOOLS NOT INCLUDED IN THE KIT

Screw Cement

CA

Screw Cement

Body Reamer

Instant Cemment

GEAR GREASE

Curved Scissors

Cutter

Gear Grease

Precision Caliper

Craft Knife

Needle Nosed Pliers

Equipment Needed UM-3 Batteries ( 8pcs ) Transmitter Brushless Electric Speed Controller

Brushless Motor

Servo

7.4V L i-Po Battery(Hard Case) L i-Po Battery Charger Receiver

PLASTIC PARTS FOR USE 40533 FRONT AND REAR GEAR BOX

40719 ARM HOLDER

40538 DIFF. CASE

31304 REAR UPRIGHT

40537 REAR UPPER ARM

40643 SHOCK PLASTIC

Parts for Not Use

40040 CENTER DIFF. MOUNT PLASTIC PARTS 40721 FRONT BUMPER

30663 VELCRO BATTERY STRAPS

PLASTIC PARTS FOR USE 30662 BATTERY CASE

40539 SERVO SAVER

40718 FRONT KNUCKLE ARM

40717 FRONT AND REAR LOWER ARM

40716 FRONT UPPER ARM

40720 SIDE IMPACT BUMPER AND BODY POST

SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL

Degrease With Motor Spray

Parts Bag Used

Do Not Over Tighten

Tighten

BAG Do Not Over Tighten

Screw Cement

Apply Screw Cement

Apply Oil Oil

Ensure Free Movement

True-To-Scale

1:1

Contact Adhesive Contact Adhesive

Tighten

Apply Grease Apply Grease

Ensure Free Movement

Anti-clockwise Rotation

Clockwise Rotation Rotate Direction

Rotate Direction

1 ASSEMBLY OF THE FRONT SHOCKS Step 1

•Assemble 2 seets for front

40636 •Fit the o-ring into groove before assembly.

Step 2

Step 3

•Be careful not to damage shock shaft.

Step 4 Fill the shocks with oil #80wt.

40640 40634 30403 40090 3.5mm O-Ring

40090 40090 2mm

40633 .....x4

40736

40643(Short)

40090

40090 1mm Washer

40090 2mm Washer

Oil .....x2

40090 1mm 40090

2.6x5mm

40737

2.6x5mm

40638

40060

.....x2 Oil

.....x2

Step 5

1.Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attach pressure top and shock oil overflow with tissue paper.

Step 6

Tighten

CORRECT SHOCK ASSEMBLY Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock is 14mm. Do not over tighten as the plastic will strip.

40640

14mm

40090 7mm R-Ring

40643 OK

0

10

30

20

40

2 ASSEMBLY OF THE REAR SHOCKS Step 1

*Assemble 2 seets for rear

40636 •Fit the o-ring into groove before assembly.

Step 2

Step 3

Step 4 •Be careful not to damage shock shaft.

40640

Fill the shocks with oil #60wt.

40634 30403 40090 40090 3.5mm O-Ring

40633

.....x4

40090 2mm

40643(Short) 40054

40090 40090 1mm Washer

.....x2

40090 1mm

Oil

2.6x5mm

40090 40090 2mm Washer

40632

40638

.....x2 2.6x5mm Oil .....x2

Step 5

1.Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attach pressure top and shock oil overflow with tissue paper.

40060

Step 6 CORRECT SHOCK ASSEMBLY

Tighten

40751

Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball end and the shock is 32mm

32mm

40090 7mm R-Ring

Do not over tighten as the plastic will strip. 40643

0

10

20

30

40

OK

3 ASSEMBLY OF THE FRONT AND REAR DIFF.

Builds two differentials for front and rear.

Step 1 40010 2.5x13.8mm Pin

Step 2

.....x4 40513

Oil 94034 4x4mm Set Screw

36053 .....x2 40538 40010

40514 40009 40009 P6 O-Ring

Oil

40009

40010

.....x4

4x4mm 40517(43T)

36053

40514 40513 36053 8x16mm Ball Bearing

.....x4

4 ASSEMBLY OF THE FRONT AND REAR DIFF.

Builds two differentials for front and rear. Tighten

Step 1

Step 2

3x12mm

30776 3x12mm

30773

40513 30776 4x10mm Washer

.....x16

•Put the Diff. Oil #100000 for front and the #5000 for Rear •Fill the Diff. case to approx. 80% with the Diff. Oil

40011

Tight the diff screws in this order.

94020 3x12mm Flat Head Hex Screw

30773 4mm Cross Pin

Diff. Oil

1

3

4

2

.....x8

.....x4

5 ASSEMBLY OF THE FRONT AND REAR GEAR CASE Step 1

Builds two gear case for front and rear.

5x4mm

ew Scerment C

Step 2

40533 40024 13x16x0.2mm Shim

.....x8 40519

Apply Grease

36053

40024

36053 8x16mm Ball Bearing

.....x4 36053

4x15mm 40533

40516(13T) 94011 4x15mm Hex Screw

.....x4

4x35mm 40024

94015 4x35mm Hex Screw

•Adjust the backlash with the shims. .....x4

6 ASSEMBLY OF THE SERVO SAVER

40037 •Tighten the steering plate hex screw all way down and then back it off 1/2 turn.

40563

Step 1

Step 2 40539

Oil 40539 40024 13x16x0.2mm Shim

40746 .....x2 40539 Ensure Free Movement

40539 4x8mm Plastic Flange Bushing

40539 40500(Black) .....x2

40024

40034 40037 Steering Plat Hex Screw

.....x2

• Notice the direction of the servo saver connecting plate.

Rotate Direction

7 ASSEMBLY OF THE SERVO SAVER 3x10mm Step 1

Step 2 40745

94041 3mm Nylon Nut

40531

.....x5 40539 3mm

94003 3x10mm Hex Screw

.....x5

40719 40719

40531 Shock Ball End Post

3mm .....x2

Right

Left

90018 3x25mm Cap Screw

S Cecrew me nt

40719 ew Scrment Ce

3x25mm

*Set the left and right hand side upper arm adjuster in the same direction.

.....x2

8 ASSEMBLY OF THE SERVO SAVER 4x12mm Scre w Cem en t

40539

w t Scre en Cem

40539

40539 94026 4x12mm Flat Head Hex Screw

.....x2 40539

40539 6x10mm Plastic Bearing

.....x4

40511

9 ASSEMBLY OF THE STEERING TIE-ROD

Assemble both right and left side.

Step 1

Step 2 40038

40548 3mm Nylon Nut (Thin Type)

40548 36700 .....x2 40038

40126 3x6mm Flange Washer

.....x2 36790 40126

40038 7mm Ball

S Cecrew me nt

36700 .....x4

1:1

3x15mm

Approx. 29.30 mm 94021 3x15mm Flat Head Hex Screw

.....x2

10 ASSEMBLY OF THE SERVO SAVER AND FRONT UPPER ARMS 4x10mm

Step 1

94020 3x12mm Flat Head Hex Screw

94026 4x12mm Flat Head Hex Screw

94009 4x10mm Hex Screw

40525 3x48.1mm Arm Shaft

.....x2

.....x4

40533 Front Plate Bed

.....x2

Front

.....x2

Step 2

40716 (1mm and 3mm)

40716

40525

*Insert the upper arm adjust into shock stay.

40719

40716 (2mm)

40525

4x12mm

Left

Right

40719 3x12mm

•Set the left and right hand side upper arms adjuster in the same direction.

11 ASSEMBLY OF THE FRONT SHOCK STAY

Assemble both right and left sides.

3x15mm

Do Not Over Tighten

Ensure Free Movement

40719(A)

40719(B)

35958 36742 Shock Cap Bushing

.....x2 36742 •Notice"L"make are for inside.

35958 5x8x2.5mm Ball Bearing

94005 3x15mm Hex Screw

.....x4

.....x2

12 ASSEMBLY OF THE FRONT SHOCKS ONTO SHOCK STAY 3x8mm

Assemble both right and left sides. 3mm

40643

Do Not Over Tighten

94041 3mm Nylon Nut

.....x2

94040 3x8mm Washer

.....x2

40643 Shock Cap Washer

.....x2

94004 3x12mm Hex Screw

.....x2

•Take the shock cap washer from the shock plastic tree.

3x12mm

13 ASSEMBLY OF THE REAR SHOCK STAY AND UPPER ARMS Step 1

Assemble both right and left sides.

Step 2

40537 40750

4x12mm 36850 36850 7mm Ball

36861 .....x2 3x10mm

94003 3x10mm Hex Screw

.....x2

94010 4x12mm Hex Screw

.....x4

40065

11 ¡G Approx. 12.5 mm

14 ASSEMBLY OF THE REAR UPPER ARMS

Right

Left

40716(1mm) •Set the left and right hand side upper arms adjuster in the same direction. 40716(2mm)

40719

40719

94011 4x16mm Hex Screw

.....x2

40546

*Insert the caster angle adjuster onto arm shaft.

40719 40546 3x42.7mm Arm Shaft

4x16mm

.....x2

15 ASSEMBLY OF THE REAR BRACE 4x12mm

40539 40539

4x15mm

94010 4x12mm Hex Screw

.....x2

94011 4x15mm Hex Screw

.....x1

16 ASSEMBLY OF THE ONE SPEED TRANSMISSION

Step 1

Step 2 6mm

S Cecre mew nt

40760

5X4mm Rotate Direction

40759

36743 6mm E-Ring

.....x1

Clockwise 35219

94036 5x4mm Set Screw

.....x1

35247 (47t) 35248 (48t) 35249 (49t) Stock

36053

40120

17 ASSEMBLY OF THE ONE SPEED TRANSMISSION

6mm Step 2 S Cecre mew nt

Step 1

S Cecre mew nt

5x4mm

5x4mm

36743 6mm E-Ring

.....x1 36053

94036 5x4mm Set Screw

40120 .....x2

18 ASSEMBLY OF THE ONE SPEED TRANSMISSION INTO THE CENTER MOUNT

Step 1

Step 2

Step 3

40040

3x10mm

4x4mm Do Not Over Tighten

40719 40714

40040 94034 4x4mm Set Screw

.....x2

94003 3x10mm Hex Screw

.....x4

40512

19 ASSEMBLY OF THE ARM HOLDER ONTO CHASSIS

*set the arm holder adjuster to the same direction. A

•set the arm holder adjuster to the same direction.

A

A

(Type A)

A

(Type A) 40761

94027 4x16mm Flat Head Hex Screw

.....x8

40719 (Front/Rear)

4x16mm

40719 40719 (Rear/Rear)

40719 (Front/Front)

40719

4x16mm

40719 (Rear/Front)

20 ASSEMBLY OF THE FRONT LOWER ARMS

Assemble both right and left sides.

Step 1

Step 2

40717 4x10mm

40719 40719

31308 40711

94035 3x8mm Set Screw

.....x2

36870 4x10mm Set Screw

.....x2

3x18mm

3x8mm •A 3x8mm set screw is use for tighten or loose stabilizer. 40711

2mm

(Left Side)

•Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle. Adjuster

94006 3x18mm Hex Screw

.....x2

Center

21 ASSEMBLY OF THE REAR LOWER ARMS

Assemble both right and left sides.

Step 1

Step 2 4x10mm

40719 40717 40719

31308

40711

3x8mm 40717

3x18mm 94035 3x8mm Set Screw

.....x2

36870 4x10mm Set Screw

.....x2

31308

2mm 40719

40719

4x10mm

•Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle. Adjuster

94006 3x18mm Hex Screw

.....x2

3x18mm 3x8mm

•A 3x8mm set screw is use for tighten or loose stabilizer.

Center

22 ASSEMBLY OF THE FRONT AND REAR GEAR BOX ONTO THE CHASSIS Step 1

94041 3mm Nylon Nut

94020 3x12mm Flat Head Hex Screw

94026 4x12mm Flat Head Hex Screw

Step 2

3mm

.....x2 3mm

.....x2

.....x2 3x12mm

94027 4x16mm Flat Head Hex Screw

3x12mm

4x16mm 4x16mm .....x8

4x16mm

4x12mm

4x16mm

23 ASSEMBLY OF THE FRONT KNUCKLE ARMS Step 1 94034 4x4mm Set Screw

Assemble both right and left sides.

Step 2

•Notice the direction of the plastic washer.

.....x2

L 36904 14mm Alum. Nut

.....x4

36055 2.5x16.8mm Pin

.....x2

40718(left) 40521(Front)

36903 40718 36904

36053 36053

Screw C em ent

36053 8x16mm Ball Bearing

40526

Do Not Over Tighten

36903 .....x4

36055

40718

4x4mm

5mm Allen Wrench 36904 36903 14mm Steering Ball

.....x4

24 ASSEMBLY OF THE FRONT SUSPENSION ARMS

Assemble both right and left sides.

•When assembling the steering balls into the arms, leave about two threads for the upper arm, and leave no room for bottom arm.

3x15mm

2.5mm Allen Wrench

94041 3mm Nylon Nut

94005 3x15mm Flat Head Hex Screw

40126

.....x2 •Put the drive shaft into cap joint before assembly.

3mm .....x2

25 ASSEMBLY OF THE FRONT PUSH RODS

Assemble both right and left sides.

Step 1

Step 2 30403 3x12mm

40063

40712

40063 30403 6mm Ball

94004 3x12mm Hex Screw

.....x4

30403 .....x2

1:1 Approx. 34mm 　３４ｍｍ

94007 3x20mm Hex Screw

.....x2

3x20mm

26 ASSEMBLY OF THE REAR WHEEL HUB

Assemble both right and left sides.

Step 1

Step 2 36082

94036 5x4mm set screw

.....x2 31304

36055 2.5x16.8mm Pin

.....x2

36055 36053 36053

.....x4

Ensure Free Movement

31307

S Cecrew me nt

40526 36053 8x16mm Ball Bearing

8x12x1mm

31305 31307 11mm Steering Ball

5x4mm 31306 .....x4

Do Not Over Tighten

27 ASSEMBLY OF THE REAR SUSPENSION ARMS

Assemble both right and left sides.

•When assembling the steering balls into the arms, leave about one threads for the rear arm, and leave no room for front arm.

(Front)

(Rear) 3mm

94041 3mm Nylon Nut

.....x2

94008 3x25mm Hex Screw

.....x2

34028

3x25mm 2.5mm Allen Wrench

*Insert the drive shaft before assembly.

28 ASSEMBLY OF THE REAR SHOCK ABSORBER

Assemble both right and left sides.

3x25mm 94040 3x8mm Washer

.....x2

94041 3mm Nylon Nut

.....x2

40531 40531 Shock Ball End Post

.....x2

94007 3x20mm Hex Screw

.....x2

90018 3x25mm Cap Screw

.....x2

40643 3x8mm 3mm

3x20mm

29 ASSEMBLY OF THE TWO SPEED TRANSMISSION ONTO THE CHASSIS

40762(97mm) • Insert drive shaft into cap joint before center assembly onto chassis.

40762(90mm)

w t Scre en Cem

94026 4x12mm Flat Head Hex Screw

4x10mm .....x4

4x10mm

30 MOTOR INSTALLATION

Motor(Not Included)

41202

4x4mm

94034 4x4mm Set Screw

w t Scre en Ce m

.....x1

3x10mm 94019 3x10mm Flat Head Hex Screw

30664-13t (stock) 30665-14t 30666-15t 30667-16t 30668-17t

.....x3

31 ASSEMBLY OF THE MOTOR MOUNT ONTO CHASSIS

Step detail

Ensure Free Movement

10114 10114 5mm Engine Mount Screw .....x2

Tighten the 10114 screw temporary.

Do Not Over Tighten

32 ADJUST MOTOR AND SPUR GEAR MAINTENANCE EXTREMELY IMPORTANT

Step 2

Step 1

Notebook Paper

Notebook Paper

Insert a notebook paper between spur gear and motor gear to make correct gear mesh.

PUSH Step 4

Step 3

PUSH

Notebook Paper

PULL OUT 3mm

Tighten •Adjust the motor mount position to get proper gear mesh. •To get a perfect gear mesh , place a piece of notebook paper between the gears and tighten the motor mount screws. •The spur gear may be damaged if the gear mesh is wrong.

33 40 ASSEMBLY OF THE VELCRO STRAP INTO BATTERY CASE 30662

Step 1

Step 2

30663

34 ASSEMBLY OF THE ELECTRIC SPEED CONTROL ONTO BATTERY CASE

•Use double side tapes. Electric Speed Control (Not Included)

35 ASSEMBLY OF THE WIRE BRIDGE ONTO BATTERY CASE AND RECEIVER BOX 3x8mm

30662

94002 3x8mm Hex Screw

.....x2

94003 3x10mm Hex Screw

.....x2

3x10mm

30662

30662

36 ASSEMBLY OF THE ELECTRIC SPEED CONTROL WIRE INTO RADIO CASE

Step 1

Step 2

*Route the speed control wire as picture shown.

*Route the speed control wire into receiver box.

37 ASSEMBLY OF THE STEERING SERVO ONTO RADIO CASE 3x10mm

3x8x0.8mm

3x10mm 3x8x0.8mm Steering Servo (Not Included)

94003 3x10mm Hex Screw

.....x4

30662B 94040 3x8x0.8mm Washer

.....x4

38 ASSEMBLY OF THE STEERING SERVO WIRE INTO RADIO CASE Steering Servo Wire

Electric Speed Control Wire

39 ASSEMBLY OF THE RADIO CASE ONTO CHASSIS Step 1

94019 3x10mm Flat Head Hex Screw

Step 2

.....x6

4x12mm 3x10mm

94026 4x12mm Flat Head Hex Screw

3x10mm

.....x1 3x10mm 4x10mm

40 ASSEMBLY OF THE RECEIVER INTO RADIO BOX Antenna Wire Step 1

Step 2

Step 3

3x8mm

30662

30560

•Plug in your speed control wire and servo wire to your receiver.

40642

30662

Receiver(Not Included)

94002 3x8mm Hex Screw

37410 .....x2

41 ASSEMBLY OF THE STEERING ROD ONTO RADIO BOX

Step 1

Step 2

Use the screw provided with your servo.

30401 30411

37320

30661 10769

30401

3x12mm

30411

3x12mm

•Approx. 16.6mm

94004 3x12mm Hex Screw

.....x2

0

10

20

30

40

42 ASSEMBLY OF THE FRONT BUMPER

40721

1:1 40721

*Approx. 30.5 mm 4mm

94042 4mm Nylon Nut

94020 3x12mm Flat Head Hex Screw

.....x3

4x12mm

.....x2 40721

Tighten

94026 4x12mm Flat Head Hex Screw

3x12mm .....x3 Tighten

43 ASSEMBLY OF THE FRONT BUMPER Completely Finished

Step 1

Step 2 40117

4x10mm

31159

40117

40721

31159 36870 4x10mm Set Screw

.....x2

Tighten

4x12mm •Approx. 4 mm 94026 4x12mm Flat Head Hex Screw

.....x2

•The 4x10mm set screw is used to adjust down stop.

Tighten

44 ASSEMBLY OF THE FRONT BUMPER 3x12mm

Tighten

40725

94020 3x12mm Flat Head Hex Screw

94009 4x10mm Hex Screw

4x10mm

Tighten

.....x2

.....x2

45 ASSEMBLY OF THE REAR BUMPER

1:1

40721

•Approx. 28.5 mm

4mm

94042 4mm Nylon Nut

.....x2 40721

94020 3x12mm Flat Head Hex Screw

.....x2

4x12mm Tighten

3x12mm 94026 4x12mm Flat Head Hex Screw

.....x2

Tighten

46 ASSEMBLY OF THE REAR BUMPER 2.6x15mm 4x10mm

Step 1

Step 2

40117

31159 2.6x15mm 40720 31159 40721 36870 4x10mm Set Screw

.....x2

94054 2.6x15mm Screw

.....x2

40720 40117

40117

•Approx. 3 mm Tighten

94026 4x12mm Flat Head Hex Screw

•The 4x10mm set screw is used to adjust down stop.

.....x2

4x12mm Tighten

47 ASSEMBLY OF THE REAR BUMPER 4x10mm

3x12mm

94004 3x12mm Hex Screw

.....x2

94009 4x10mm Hex Screw

.....x2

48 BATTERY INSTALL Follow the manual instruction sprovided by ESC manufacturer to install the wire.

Battery(Not Included)

•Be aware of the direction of the battery.

•If use hard case battery , make a hole as picture shown.

15mm

Hard Case Battery 8mm

17

49 ASSEMBLY OF THE TIRES AND WHEELS

(Right Hand Side)

•Notice the direction of the tires. (Left Hand Side)

•Notice the direction of the tires.

86052 STOCK NO BELT 86053 WITH BELT

•Notice the direction of the tires. Make two the same for the left and 2 for the right. Check the rotation direction before gluing.

Contact Adhesive

Contact Adhesive

Contact Adhesive

Contact Adhesive

86023 86024 86025 86026 86027 86028

BLACK BLUE LIME WHITE ORANGE GRAY •Pull back the tire bead slightly and spot glue in four spots as shown. When dry, glue the rest of the wheel between the spots. Repeat the procedure on the other side of the wheel until fully glued.

86059

INS

TA GL NT UE

86059

50 ASSEMBLY OF THE WHEELS ONTO THE FRONT KNUCKLE AND REAR HUB

Assemble both right and left side.

Step 1

•Notice the direction of the tire pattern.

•Tire and Wheel assembly.

40550 40550 Wheel Nut

.....x4

51 MAKING HOLES AND CUTTING ON THE BODY SHELL

Step 1

Step 2

31157

Right

Left

Wing Side Plate Cut the body shelll as shown.

52 MAKING HOLES AND CUTTING ON THE BODY SHELL Step 1

Step 2 Body Reamer (not included)

Make 7mm holes

Hole Position Make 4mm holes

Hole Position

Hole Position

Before making holes on the body, put the unpainted body on the chassis to confirm the mounting position and location for holes.

Make 9mm holes on the body shell as shown.

53 MAKING HOLES AND CUTTING ON THE WING

54 MAKING HOLES AND CUTTING ON THE WING

Step 1

Step 2

Make 3mm holes

Wing Side Plate(L) Make 3mm holes

The position and the wing is the same.

Make a 7mm hole

Make 3mm hole Wing Side Plate(R) Make a 7mm hole

Make 3mm hole

55 WASH THE INSIDE OF THE BODY SHELL

Wash the inside of the body shell with mild detergent, and then rinse and dry thoroughly.

Step 1

Step 2

56 PAINTING BODY SHELL Step 2 Step 1

Paint the body with polycarbonate spray paints.

Mask the windows on the inside with masking tape.

•When the paint is dry, remove the masking. •When you have finished painting, peel off the external protective films.

57 ASSEMBLY OF THE WING ONTO THE BODY SHELL

Step 1

Step 2

Nylon Nut

3mm Nylon Screw 94001 3x5mm Hex Screw

.....x2

.....x4 3x5mm Nylon Nut

94041 3mm Nylon Nut

.....x4

Nylon Nut

.....x2

58 MOUNTING THE BODY SHELL

31159

31159

SETTING GUIDE FRONT TOE-IN AND TOE-OUT SETTING

Use a 2.5mm allen wrench to adjust toe-in for front and rear. (Front) Adjust the length of the front steering rod to change the toe angle.

NEUTRAL POSITION

Making the steering rod longer will make the front tires become toe-in. Response will be slower and will over steer.

TOE-IN TOE-OUT

TOE-OUT

Making the steering rod shorter will make the front tires become toe-out. Response will be quicker and will under steer. We recommended adjusting the front toe-out to 1.5 degrees. (Rear) Adjust the length of the rear hub (12mm ball/rear) to change the toe angle. Making the 12mm ball longer will make the rear tires toe-in. Response will be under steer. Steering Rod

REAR TOE-IN

Making the 12mm ball shorter will make the rear tires toe-out. Response will be over steer. We recommended adjusting the rear toe-in to 2 degrees.

REAR TOE-IN

2.5mm Allen Wrench

FRONT AND REAR CAMBER ANGLE SETTING

•Use 2.5mm hex wrench to adjust upper arm ball in front.

Note: Place the model car on a flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angles to the ground.

(REAR)

(FRONT)

Turnbuckle

+ Positive

-

-

+

+ Positive

Negative

-

-

+

Negative

Adjust the length of the turnbuckle on the rear upper arms can be change the rear camber. We suggest using 2 degrees of negative camber for the rear.

The front camber adjustment can be made by moving the 14mm steering ball at the front upper arms on knuckles, clockwise or anticlockwise. We suggest using 1.5 degrees of negative camber for the front.

FRONT AND REAR SHOCK ANGLE SETTING 1 2

Firm

Soft

Soft

(FRONT)

1234

(REAR)

Firm

Soft Firm front suspension, less steering. Soft front suspension, more steering.

12

Firm

Soft Firm rear suspension, over steering. Soft rear suspension, under steering.

12

Firm

34328 DM-1e SPEC PARTS LIST OFNA 10114 10769 30401 30403 30411 30560 30662 30663 30664 30665 30666 30667 30668 30773 30774 30776 31140 31141 31144 31157 31159 31304 31305 31306 31307 31308 34028 35247 35248 35249 35958 36053 36055 36082 36700 36742 36790 36850 36861 36903 36904 37320 37410 37650 40009 40010 40011 40024 40034 40037 40038 40040 40054 40060 40063 40065 40090 40117 40120 40126 40500 40563

DESCRIPTIONS ENGINE MOUNT SCREWS,FLAT HEAD SERVO SAVER INSERTS,BLK ALL RADIO STEERING ENDS, PLASTIC 6 PCS. 6mm BALL, STEEL (NO COLLAR) 6mm BALLS w/COLLAR,STEERING 6P ANT TUBE AND MOUNT BATTERY CASE,RX BOX LX-1e BATTERY VELCRO STRAPS LX-1e PINION 13T 5MM SHAFT PINION 14T 5MM SHAFT PINION 15T 5MM SHAFT PINION 16T 5MM SHAFT PINION 17T 5MM SHAFT CROSS PIN AXLES, 4mm STEEL CROSS PIN AXLES, 4mm ALUM 6PCS WASHER, 4x10x0.2mm 4PCS. BODY, C-TYPE WITH DECALS BODY, M-TYPE CLK DECALS/MASK BODY, V-GTP WITH DECALS BODY, CLEAR DP8 1/8 GTP BODY BODY CLIPS, CHROME UP-RIGHT HUB REAR, PIVOT BALL WASHER, PIVOT BALL, PLASTIC ALUM. HEX NUT, PIVOT BALL 4PCS PIVOT BALL, STEEL, REAR 4PCS BARS, BALL & CUP SET DOG BONE, 100mm SPUR, GEAR, 47T, 2SP REV2 SPUR, GEAR, 48T, 2SP REV2 SPUR, GEAR, 49T, 2SP REV2 BEARING, 5X8mm 1 PC. BEARING, 8x16mm, PAIR PIN, 2.5x17mm, HEX HUBS, 4PCS REAR AXLES, 8mm PAIR STEERING BALL END, 7mm, 8PCS. BUSHING, SERVO SAVER 4x46MMTURNBUCKLES,4PCS. 7mm BALL, 6 PCS. 5x40mm TURNBUCKLES, 2 PCS BLK PIVOT BALLS, STEEL (mbx4) 4PCS 14mm ALUM. NUT (mbx4) 4 PCS TURNBUCKLES, 3x26mm 2 PC BODY CLIPS, 10 PCS. SMALL JL10 PLASTIC BALL END,4mm JL10 DIFF O-RING SEALS, 2PCS DIFF PINS,2.5X13.8MM,2PCS DIFF GASKETS,3PCS OUTER DIFF SHIM,13X16XO.2MM SERVO SAVER RING,ADJ. NUT,ALUM STEERING PLATE HEX SCREWS BALLS, 7MM 4PCS. CENTER DIFF MOUNT,NYLON SHOCK SHAFTS,3.5m FR 13/16mm SHOCK PISTON LOCKNUT,2.5mm,4PC SHOCK SPRING CUP,4 PCS. REAR UPPER ARM PLASTIC ROD END SHOCK REBIULD KIT,13MM TRUCK BODY MOUNT NEW BRAKE CAP JOINT,8MM DM-1 WASHER FLANGE 3x6x2.5 SERVO SAVER SPRING, X1-CR SERVO SAVER TUBE

RETAIL OFNA 7.95 0.99 2.95 4.95 4.95 2.95 19.95 9.95 12.95 12.95 12.95 12.95 12.95 3.95 9.95 1.95 64.95 64.95 59.95 59.95 4.95 10.95 5.95 8.95 8.95 10.95 15.95 7.95 7.95 7.95 3.95 12.95 3.95 10.95 6.95 1.95 10.95 3.95 6.95 7.95 9.95 3.95 3.95 6.95 2.95 2.95 3.95 2.95 5.95 5.95 9.95 4.95 7.95 4.95 6.95 4.95 7.95 10.95 11.95 3.95 3.95 9.95

40511 40512 40513 40514 40516 40517 40519 40521 40525 40526 40531 40533 40537 40538 40539 40546 40548 40550 40632 40633 40634 40636 40638 40640 40642 40643 40711 40712 40714 40716 40717 40718 40719 40720 40721 40725 40736 40737 40738 40745 40746 40750 40751 40759 40760 40761 40762 41202 86023 86024 86025 86026 86027 86028 86029 86030 86050 86051 86052 86053 86059

DESCRIPTIONS SERVO SAVER SPRING POST CENTER DIFF. MOUNT POST DIFF. GEAR (small & large)ALUM CAP JOINT FOR DIFF. STEEL SMALL BEVEL GEAR 13T STEEL BEVEL GEAR 43T CAP JOINT, CENTER PINION GEAR UNIVERSAL JOINT, FRONT SHAFT 3x48.1mm DM UPPER FRONT WHEEL HUB 17MM SHOCK BALL POST/ONE-PIECE/TOP GEAR CASE UPPER ARMS DIFF CASE F&R PLASTIC SERVO SAVER & CNT BRAC FRONT ARM SHAFT 3x42.7mm NUT M3 NYLON (Thin Type) WHEEL NUT 17mm LX-2 SHOCK BODY FRONT 13mm SHOCK CAP, 13mm SHOCK SPRINGS ADJUSTER, 13mm O-RING 15x1mm SHOCK PISTON 13mm SHOCK, PRESSURE TOP, ORANGE ANTENNA , FIXING NUT PLASTIC SHOCK PARTS,13/16mmLX2 4x90mm LOWER ARM SHAFT DM TURNBUCKLE,3.5x48mm,DM HANDLE BAR, CENTER DM UPPER ARM FRONT,DM LOWER ARMS FRONT & REAR DM STEERING KNUCKLE,PIVOT BALL DM ARM HOLDER PLASTIC DM BUMPER,SIDE BODY DM BUMPER FRONT & REAR DM BUMPER FOAM DM SHOCK SHAFT DM-1 SHOCK BODY, 13mm DM-1 SHOCK SPRING DM-1 RED SOFT UPPER FRONT PLATE BLACK SERVO CONNECTING PLATE BLACK SHOCK TOWER RR ALUM DM1 SPEC SPRINGS, RR RED SOFT DM1-SPEC SINGLE GEAR SHAFT DM-1E CENTER GEAR MOUNT DM-1E CHASSIS CNC 6061 DM-1E CENTER DOGBONE DM-1E 90/97MM CNC MOTOR MOUNT NEXX8 17mm WHEELS, V SPOKE, BLACK PK 17mm WHEELS, V SPOKE, BLUE PK 17mm WHEELS, V SPOKE, LIME PK 17mm WHEELS, V SPOKE, WHITE PK 17mm WHEELS, V SPOKE,ORANGE PK 17mm WHEELS, V SPOKE, GRAY PAK 17mm WHEELS, V SPOKE, YEL PACK 17mm WHEELS, V SPOKE,CHROME PK 1:8 TIRE, SLICK w/o BELT, PAIR 1:8 TIRE, SLICK with BELT,PAIR 1:8 TIRE,TREADED w/o BELT, PR. 1:8 TIRE,TREADED with BELT,PR. FOAM STRIPS, INSERTS, LOW-PRO

RETAIL 6.95 13.95 16.95 13.95 14.95 38.95 9.95 44.95 6.95 11.95 9.95 11.95 6.95 9.95 11.95 11.95 1.95 4.95 24.95 18.95 9.95 3.95 7.95 5.95 2.95 9.95 7.95 9.95 3.95 9.95 19.95 19.95 15.95 9.95 19.95 14.95 7.95 24.95 14.95 7.95 9.95 14.95 9.95 12.95 14.95 99.95 19.95 29.95 19.95 19.95 19.95 19.95 19.95 19.95 19.95 23.95 19.95 35.95 19.95 35.95 9.95

OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer location. Other items such as radio and engine other covered by individual warranties. IMPORTANT! Please print or type, filling in the information listed below and mail immediately

MAIL TO: OFNA RACING 7 VANDERBILT IRVINE, CA. 92618 TEL: (949) 586-2910

Write in Your Model Name and Part Number

REGISTRATION CARD

RACER’S NAME

TEL:(

)

ADDRESS

CITY

STATE

DEALER’S NAME

ZIP

TEL: (

ADDRESS

CITY

OFNA 7 Vanderbilt Irvine, Ca. 92618

STATE

ZIP

)