enervex® tdf 560-685 power venter
ENERVEX TDF 560-685 POWER VENTER ®
Product Information
3902025 05.16
Use
The TDF Power Venter is a true in-line power venter. It is specifically designed for applications where reliable and efficient operation, low noise level, low energy consumption, variable speed and compact design are of utmost importance. Typical applications are: mechanical venting of gas-fired or oil-fired boilers and water heaters. For indoor or outdoor installation.
Description
The TDF Power Venter is an efficient, high-temperature ventilator with backward-inclined impeller. It can be installed horizontally or vertically in a chimney system. The fan housing is made of stainless steel and equipped with an energy-efficient, totally enclosed, variable speed motor, which is mounted outside the air stream. The bolt-flange stack connections fit most commercial pre-fabricated chimney systems. The fan is typically installed hung from ceiling mounting brackets to support the weight. The complete drive unit (motor, impeller and mounting plates) can be removed from the fan without the need for removing the housing from the stack system. The TDF is for use with condensing and non-condensing appliances operating where flue gas temperatures do not exceed 1400°F (760°C). The TDF model is a component in the CASI, Chimney Automation System.
Optional Equipment
Material
• EBC 30/31 Modulating Pressure Controller
The housing is made of 316L stainless steel and has bolt-flange connection. The impeller is of the backward inclined type made of 316L stainless steel.
Motor
The motor is an air cooled, maintenance-free variable speed permanent magnet motor with pre-lubricated and sealed ball bearings. The motor and controller is rated at 92% efficiency (motor and controller) and able to operate as low as 50 RPM. The motor has integrated protection against overloading, blocking over and under voltage and over-heating. The motor shaft in internally isolated to eliminate the need for external shaft grounding. The required motor control is factory programmed by ENERVEX for optimal operation of the ventilator.
Standard Equipment
• EBC 35 Modulating Pressure Controller • PDS Proven Draft Switch
Listings
UL Listing under Category MCQX is pending (UL Project Number 4786951498) and references the following standards: • UL 378 Standard for Draft Equipment Edition 4 - Revision Date 2013/09/17 • UL 705 Standard for Power Ventilators Edition 6 - Revision Date 2013/12/17 • CSA C22.2 NO. 113-12 Fans and Ventilators Edition 9 - Revision Date 2012/10/01 • CSA3-B255-M81 Standard for Mechanical Flue Gas Exhauster
Warranty
• EDrive Motor Control
• 2-Year Factory Warranty. • 10-Year Warranty Against Corrosion Perforation Complete warranty conditions are available from ENERVEX Inc.
Specifications are subject to change without notice. ENERVEX Inc. 1685 Bluegrass Lakes Parkway Alpharetta, GA 30004 USA
P: 770.587.3238 F: 770.587.4731 T: 800.255.2923 [email protected] www.enervex.com
ENERVEX TDF 560-685 POWER VENTER ®
Product Information
3902025 05.16 Specifications Model
TDF 560
Fan Type
TDF 620
TDF 685
Centrifugal Impeller (B-wheel)
Motor Type
TEFC
Voltage
VAC
Amperage
3 x 208-240 / 3 x 400-480
Amps
Motor
12.0 / 6.0
24.0 / 12.0
48.0 / 24.0*
Output HP
5.0
10.0
20.0
kW
3.7
7.4
15.0
Max. RPM Dimensions
1740
1740
1740
A in (mm)
36.3 (922)
36.0 (914)
39.4 (1001)
B in (mm)
36.8 (935)
48.3 (1227)
49.5 (1257)
C in (mm)
34.3 (871)
38.4 (975)
43.9 (1115)
D in (mm)
38.5 (978)
48.3 (1227)
49.5 (1257)
E in (mm)
31.7 (805)
38.4 (975)
43.9 (1115)
F in (mm)
45.3 (1151)
55.3 (1405)
62.3 (1582)
G in (mm)
43.4 (1102)
45.6 (1158)
53.0 (1346)
H in (mm)
3.4 (86)
3.5 (89)
6.4 (163)
I in (mm)
3.4 (86)
3.5 (89)
6.4 (163)
J in (mm)
35.0 (889)
39.0 (991)
45.2 (1148)
K in (mm)
33.5 (851)
37.4 (950)
43.7 (1110)
L in (mm)
32.00 (813)
36.0 (914)
M in (mm)
35.0 (889)
39.0 (997)
42.0 (1067) CAPACITY CHART
ENERVEX MODEL TDF685 INLINE POWER VENTER
45.2 (1148)
N in (mm)
33.5 (851)
37.4 (950)
O in (mm)
32.0 (813)
36.0 (914)
42.0 (1067)
P in (mm)
.5 (13)
Q Weight
43.7 (1110)
0.5 (13)
.5 (13)
qty
8
8
8
lbs
378
432*
502*
kg
172
196
228
Capacity:
A H
8.0
D
Inch WC
AIR FLOW
7.0 B
F
6.0 5.0 TDF 685
4.0 I
C
MOUNTING TABS 1.00 16X
E
J
TDF 560
2.0
M
K
G
TDF 620
3.0
1.0
N O
L
0.0 0
3,000
6,000
9,000
12,000
CFM P TYPICAL OF Q
P TYPICAL OF Q
Specifications are subject to change without notice. ENERVEX Inc. 1685 Bluegrass Lakes Parkway Alpharetta, GA 30004 USA
P: 770.587.3238 F: 770.587.4731 T: 800.255.2923 [email protected] www.enervex.com
15,000
18,000
21,000
Product Information
3902025 05.16
Use
The TDF Power Venter is a true in-line power venter. It is specifically designed for applications where reliable and efficient operation, low noise level, low energy consumption, variable speed and compact design are of utmost importance. Typical applications are: mechanical venting of gas-fired or oil-fired boilers and water heaters. For indoor or outdoor installation.
Description
The TDF Power Venter is an efficient, high-temperature ventilator with backward-inclined impeller. It can be installed horizontally or vertically in a chimney system. The fan housing is made of stainless steel and equipped with an energy-efficient, totally enclosed, variable speed motor, which is mounted outside the air stream. The bolt-flange stack connections fit most commercial pre-fabricated chimney systems. The fan is typically installed hung from ceiling mounting brackets to support the weight. The complete drive unit (motor, impeller and mounting plates) can be removed from the fan without the need for removing the housing from the stack system. The TDF is for use with condensing and non-condensing appliances operating where flue gas temperatures do not exceed 1400°F (760°C). The TDF model is a component in the CASI, Chimney Automation System.
Optional Equipment
Material
• EBC 30/31 Modulating Pressure Controller
The housing is made of 316L stainless steel and has bolt-flange connection. The impeller is of the backward inclined type made of 316L stainless steel.
Motor
The motor is an air cooled, maintenance-free variable speed permanent magnet motor with pre-lubricated and sealed ball bearings. The motor and controller is rated at 92% efficiency (motor and controller) and able to operate as low as 50 RPM. The motor has integrated protection against overloading, blocking over and under voltage and over-heating. The motor shaft in internally isolated to eliminate the need for external shaft grounding. The required motor control is factory programmed by ENERVEX for optimal operation of the ventilator.
Standard Equipment
• EBC 35 Modulating Pressure Controller • PDS Proven Draft Switch
Listings
UL Listing under Category MCQX is pending (UL Project Number 4786951498) and references the following standards: • UL 378 Standard for Draft Equipment Edition 4 - Revision Date 2013/09/17 • UL 705 Standard for Power Ventilators Edition 6 - Revision Date 2013/12/17 • CSA C22.2 NO. 113-12 Fans and Ventilators Edition 9 - Revision Date 2012/10/01 • CSA3-B255-M81 Standard for Mechanical Flue Gas Exhauster
Warranty
• EDrive Motor Control
• 2-Year Factory Warranty. • 10-Year Warranty Against Corrosion Perforation Complete warranty conditions are available from ENERVEX Inc.
Specifications are subject to change without notice. ENERVEX Inc. 1685 Bluegrass Lakes Parkway Alpharetta, GA 30004 USA
P: 770.587.3238 F: 770.587.4731 T: 800.255.2923 [email protected] www.enervex.com
ENERVEX TDF 560-685 POWER VENTER ®
Product Information
3902025 05.16 Specifications Model
TDF 560
Fan Type
TDF 620
TDF 685
Centrifugal Impeller (B-wheel)
Motor Type
TEFC
Voltage
VAC
Amperage
3 x 208-240 / 3 x 400-480
Amps
Motor
12.0 / 6.0
24.0 / 12.0
48.0 / 24.0*
Output HP
5.0
10.0
20.0
kW
3.7
7.4
15.0
Max. RPM Dimensions
1740
1740
1740
A in (mm)
36.3 (922)
36.0 (914)
39.4 (1001)
B in (mm)
36.8 (935)
48.3 (1227)
49.5 (1257)
C in (mm)
34.3 (871)
38.4 (975)
43.9 (1115)
D in (mm)
38.5 (978)
48.3 (1227)
49.5 (1257)
E in (mm)
31.7 (805)
38.4 (975)
43.9 (1115)
F in (mm)
45.3 (1151)
55.3 (1405)
62.3 (1582)
G in (mm)
43.4 (1102)
45.6 (1158)
53.0 (1346)
H in (mm)
3.4 (86)
3.5 (89)
6.4 (163)
I in (mm)
3.4 (86)
3.5 (89)
6.4 (163)
J in (mm)
35.0 (889)
39.0 (991)
45.2 (1148)
K in (mm)
33.5 (851)
37.4 (950)
43.7 (1110)
L in (mm)
32.00 (813)
36.0 (914)
M in (mm)
35.0 (889)
39.0 (997)
42.0 (1067) CAPACITY CHART
ENERVEX MODEL TDF685 INLINE POWER VENTER
45.2 (1148)
N in (mm)
33.5 (851)
37.4 (950)
O in (mm)
32.0 (813)
36.0 (914)
42.0 (1067)
P in (mm)
.5 (13)
Q Weight
43.7 (1110)
0.5 (13)
.5 (13)
qty
8
8
8
lbs
378
432*
502*
kg
172
196
228
Capacity:
A H
8.0
D
Inch WC
AIR FLOW
7.0 B
F
6.0 5.0 TDF 685
4.0 I
C
MOUNTING TABS 1.00 16X
E
J
TDF 560
2.0
M
K
G
TDF 620
3.0
1.0
N O
L
0.0 0
3,000
6,000
9,000
12,000
CFM P TYPICAL OF Q
P TYPICAL OF Q
Specifications are subject to change without notice. ENERVEX Inc. 1685 Bluegrass Lakes Parkway Alpharetta, GA 30004 USA
P: 770.587.3238 F: 770.587.4731 T: 800.255.2923 [email protected] www.enervex.com
15,000
18,000
21,000
