Enhanced Display Installation Manual
Basic / Enhanced Display Installation Manual
07.14.15
Item # 205500
Warning Statement
Warning: READ THIS STATEMENT. Throughout this installation manual you will find Warning: statements. Pay special attention to these warnings. Failure to follow the specific instructions will result in an unsafe condition in which serious injury could result!
Index Installation Sheet Name Cover Page Warning Statement Index Assembly Overview Standard Display Assembly Anchoring Display Securing Display Together Adjusting Shelving/Shelving Installation Non-Lighted Header Standard Sign
Assembly Overview 1. Assemble, position and bolt all bases together. See “Securing Displays Together” installation sheet. 2. Assemble each metal low profile display with ALL items, except shelving, including lights. Do this one display at a time, on the floor (not attached to the bases). Pre-wire all electronic equipment (See instruction sheet in Light Kit for power cord routing). 3. Set pre-assembled, pre-wired low profile displays on top of bases one at a time. Secure to wall as you add each one. Secure each metal display to adjoining metal displays and bases as you add each one. 4. Install shelving (refer to installation sheet “Shelving Installation”). 5. Install accessories. 6. Install advertising. 7. Merchandise product. 8. Questions? Call 800-704-3660.
Warning: Failure to bolt all displays together results in an unsafe condition in which the display could fall over causing injury. Warning: Failure to secure all metal displays to bases results in an unsafe condition in which the display could fall over causing injury. Warning: Failure to anchor the displays to the wall results in an unsafe condition in which the display could fall over causing injury. Tools Required (not included): • •
Pliers (7116 wrench) Phillips screwdriver
Anchoring: • • •
Cordless Drill 1/4” Drill Bit 5/8” Drill Bit
Standard Profile Display Assembly Note: A standard profile display is a combination of a low profile display on top of a base cabinet.
1.
Remove 2 front adjustable levelers from low profile display.
2.
Loosen 2 rear adjustable levelers on the low profile display approximately 1/4”.
3.
Set low profile display on base. Slide low profile display forward so that rear levelers engage slots in top of base.
4.
Hand-tighten rear levelers to help keep displays positioned.
5. Fasten display together with 4 supplied screws and nuts.
6. Space shelves according to retailer requirements.
Warning: Displays must be properly anchored to each other and the wall. Failure to do so results in an unsafe condition in which the display could fall over causing injury.
(2)
*Remove 2 front levelers
Loosen levelers approx. 1/4”
Slots
Anchoring Display - Metal Item #703013 Contents: (2) #10-24 1¼” Machine screws
(2) #10-16 3/4” Self-tapping screws
(2) Fender washers
(2) Togglers (2) #10 Washers
(2) #10 Keps nuts
(2) #10-24 4” Machine screws (1) Cable Kit
(2) Angle brackets
(2) 1/4-20 x 5” Carriage bolts
*Note: Some parts will remain unused for your application
(2) 1/4-20 Nylocks
Warning: Failure to anchor the displays to the wall results in an unsafe condition in which the display could fall over causing injury. Anchor locations
Individual display
Anchor locations
*Note: Display(s) shown without shelves installed
Multiple display
Notes: • Individual displays should be anchored in both top corners. • Multiple displays should be anchored in both top corners and where displays join each other.
Anchoring Display - Metal Item #703013 For anchoring to drywall: Display Wall Drill through wall
1.
Position display next to wall. Drill through top holes in metal uprights with 1/4” bit, into wall (Fig. A).
2.
Move display away from wall. Drill out holes to 5/8”, flip metal flanges of Togglers 90° and insert (Fig. B). Pull taut, pushing plastic collar into hole and snapping off excess (Fig. C).
3.
Reposition display and secure to Toggles in wall with 4” machine screws, and fender washers (Fig. C).
A
Push plastic collar into hole and snap off excess
Drill holes out to 5/8” Move display away
Insert Togglers
B
Turn metal flange 90°
C
4” machine screws through display holes, spacers, fender washers, into Togglers
Anchoring Display - Metal Item #703013 For anchoring to window mullion: Determine locations on window mullion for angle brackets. Use 2 self-drill/tap screws to mount 1 bracket to mullion. (Fig. A). Secure display to angle bracket using Gripples as shown (Figs. B, C, D, E & F).
Thread pre-looped portion of wire through wall bracket
Window mullion
OR
II. Thread loose end of wire through loop
Self-tapping screws
A Pull wall bracket loop taut and thread metal catch
B Thread loose end through display and back through metal catch. (Pull taut. Loop length exaggerated to show path.)
C Key
GRIPPLE
E
Detail of catch and cable
GRIPPLE
F
To remove cable from catch, insert key as shown and pull cable out.
D
Securing Displays Together Warning: Failure to anchor the displays to each other and the wall results in an unsafe condition in which the display could fall over causing injury.
1.
Adjust levelers to align displays.
2.
Multiple displays should be secured together with bolt sets provided.
Suggested/available securing holes
Adjust levelers (4)
Shelving Installation and Adjusting Knife Bracket Installation Slotted channel Lift shelf up and pull forward to remove
Pull back on locking tab on both sides
Side view
1.
To adjust shelf support, gently pull back on locking tab untill pin is disengaged from slot. Do this on both sides of support.
2.
Locking pin should automatically lock into place when inserting shelf support into new location.
Warning: Make sure locking pin is engaged into slot. Test each shelf after installing to make sure it cannot be knocked loose. Failure to do so can result in an unsafe condition in which the shelf could be knocked off the metal display causing injury.
Shelf Installation
1.
Locate spring tabs and pins on both sides of shelf bottoms.
Spring tabs
Front view
2.
Metal frame
B
Rotate shelf so that pin engages groove in plastic slide.
3. On opposite side of shelf, pull spring tab while rotating side of shelf downward.
A
Slide
Pin
Pull spring tab while rotating downward
Front view
Non-Lighted Header Standard Sign
Tabs go into mounting slots
Mounting tabs
Mounting tabs
Mounting slots
Side View
High Low
Adjustable Height
Hang the sign channel mounting brackets on the metal display by engaging the selected sign channel mounting tabs in the mounting slots located on the metal display. Push down on channel to secure mounting tabs in mounting slots. Note: Normal setting is in the highest position.
07.14.15
Item # 205500
Warning Statement
Warning: READ THIS STATEMENT. Throughout this installation manual you will find Warning: statements. Pay special attention to these warnings. Failure to follow the specific instructions will result in an unsafe condition in which serious injury could result!
Index Installation Sheet Name Cover Page Warning Statement Index Assembly Overview Standard Display Assembly Anchoring Display Securing Display Together Adjusting Shelving/Shelving Installation Non-Lighted Header Standard Sign
Assembly Overview 1. Assemble, position and bolt all bases together. See “Securing Displays Together” installation sheet. 2. Assemble each metal low profile display with ALL items, except shelving, including lights. Do this one display at a time, on the floor (not attached to the bases). Pre-wire all electronic equipment (See instruction sheet in Light Kit for power cord routing). 3. Set pre-assembled, pre-wired low profile displays on top of bases one at a time. Secure to wall as you add each one. Secure each metal display to adjoining metal displays and bases as you add each one. 4. Install shelving (refer to installation sheet “Shelving Installation”). 5. Install accessories. 6. Install advertising. 7. Merchandise product. 8. Questions? Call 800-704-3660.
Warning: Failure to bolt all displays together results in an unsafe condition in which the display could fall over causing injury. Warning: Failure to secure all metal displays to bases results in an unsafe condition in which the display could fall over causing injury. Warning: Failure to anchor the displays to the wall results in an unsafe condition in which the display could fall over causing injury. Tools Required (not included): • •
Pliers (7116 wrench) Phillips screwdriver
Anchoring: • • •
Cordless Drill 1/4” Drill Bit 5/8” Drill Bit
Standard Profile Display Assembly Note: A standard profile display is a combination of a low profile display on top of a base cabinet.
1.
Remove 2 front adjustable levelers from low profile display.
2.
Loosen 2 rear adjustable levelers on the low profile display approximately 1/4”.
3.
Set low profile display on base. Slide low profile display forward so that rear levelers engage slots in top of base.
4.
Hand-tighten rear levelers to help keep displays positioned.
5. Fasten display together with 4 supplied screws and nuts.
6. Space shelves according to retailer requirements.
Warning: Displays must be properly anchored to each other and the wall. Failure to do so results in an unsafe condition in which the display could fall over causing injury.
(2)
*Remove 2 front levelers
Loosen levelers approx. 1/4”
Slots
Anchoring Display - Metal Item #703013 Contents: (2) #10-24 1¼” Machine screws
(2) #10-16 3/4” Self-tapping screws
(2) Fender washers
(2) Togglers (2) #10 Washers
(2) #10 Keps nuts
(2) #10-24 4” Machine screws (1) Cable Kit
(2) Angle brackets
(2) 1/4-20 x 5” Carriage bolts
*Note: Some parts will remain unused for your application
(2) 1/4-20 Nylocks
Warning: Failure to anchor the displays to the wall results in an unsafe condition in which the display could fall over causing injury. Anchor locations
Individual display
Anchor locations
*Note: Display(s) shown without shelves installed
Multiple display
Notes: • Individual displays should be anchored in both top corners. • Multiple displays should be anchored in both top corners and where displays join each other.
Anchoring Display - Metal Item #703013 For anchoring to drywall: Display Wall Drill through wall
1.
Position display next to wall. Drill through top holes in metal uprights with 1/4” bit, into wall (Fig. A).
2.
Move display away from wall. Drill out holes to 5/8”, flip metal flanges of Togglers 90° and insert (Fig. B). Pull taut, pushing plastic collar into hole and snapping off excess (Fig. C).
3.
Reposition display and secure to Toggles in wall with 4” machine screws, and fender washers (Fig. C).
A
Push plastic collar into hole and snap off excess
Drill holes out to 5/8” Move display away
Insert Togglers
B
Turn metal flange 90°
C
4” machine screws through display holes, spacers, fender washers, into Togglers
Anchoring Display - Metal Item #703013 For anchoring to window mullion: Determine locations on window mullion for angle brackets. Use 2 self-drill/tap screws to mount 1 bracket to mullion. (Fig. A). Secure display to angle bracket using Gripples as shown (Figs. B, C, D, E & F).
Thread pre-looped portion of wire through wall bracket
Window mullion
OR
II. Thread loose end of wire through loop
Self-tapping screws
A Pull wall bracket loop taut and thread metal catch
B Thread loose end through display and back through metal catch. (Pull taut. Loop length exaggerated to show path.)
C Key
GRIPPLE
E
Detail of catch and cable
GRIPPLE
F
To remove cable from catch, insert key as shown and pull cable out.
D
Securing Displays Together Warning: Failure to anchor the displays to each other and the wall results in an unsafe condition in which the display could fall over causing injury.
1.
Adjust levelers to align displays.
2.
Multiple displays should be secured together with bolt sets provided.
Suggested/available securing holes
Adjust levelers (4)
Shelving Installation and Adjusting Knife Bracket Installation Slotted channel Lift shelf up and pull forward to remove
Pull back on locking tab on both sides
Side view
1.
To adjust shelf support, gently pull back on locking tab untill pin is disengaged from slot. Do this on both sides of support.
2.
Locking pin should automatically lock into place when inserting shelf support into new location.
Warning: Make sure locking pin is engaged into slot. Test each shelf after installing to make sure it cannot be knocked loose. Failure to do so can result in an unsafe condition in which the shelf could be knocked off the metal display causing injury.
Shelf Installation
1.
Locate spring tabs and pins on both sides of shelf bottoms.
Spring tabs
Front view
2.
Metal frame
B
Rotate shelf so that pin engages groove in plastic slide.
3. On opposite side of shelf, pull spring tab while rotating side of shelf downward.
A
Slide
Pin
Pull spring tab while rotating downward
Front view
Non-Lighted Header Standard Sign
Tabs go into mounting slots
Mounting tabs
Mounting tabs
Mounting slots
Side View
High Low
Adjustable Height
Hang the sign channel mounting brackets on the metal display by engaging the selected sign channel mounting tabs in the mounting slots located on the metal display. Push down on channel to secure mounting tabs in mounting slots. Note: Normal setting is in the highest position.
