Fellowes Powerhouse1000 PS 2001 Manual
Fellowes Powerhouse 1000 Table Top Paper Shredder Instruction Manual
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Powershred
®
Table Top Paper Shredder
Operating Instructions
Powerhouse 1000 X
Important Safety Instructions
Installation
1. Read all instructions before use. Unpack your new shredder from its shipping 2. Save these instructions for later use. container. 3. Follow all warnings and instructions marked on the Place the shredder on a table top, desk or the product. optional shredder stand. Be sure the selected work 4. Unplug this product from the wall outlet before surface is strong enough to support the weight of cleaning. Clean with a damp cloth using a mild soap and water solution. (Do not use abrasives or petroleum the shredder. based cleaners.) To attach the wire form feed guide, tilt the shredder 5. Place this product as close as possible to power source back until the front feet lift off the table. Angle the for quick and easy unplugging. Do not block the power wire form feed guide so one “U” curve fits around supply receptacle; it must be possible to conveniently one of the metal tabs. Wrap the other side’s “U” unplug the power cord. curve around the other metal tab. Set the shredder 6. Do not use this product near water. down so the front edge of the guide extends one7. This product should never be placed near or over a half in front of the machine, with the rest of the radiator or heat source. 8. Operate from the type of power source indicated on guide between the shredder and the table. the marking label. If you are not sure of the type of Holding the bag support rod horizontally, pull the power available, consult your dealer or local electricity bag up through the center of the rod and wrap the board. edges of the bag over the rod. To attach the rod to 9. Do not allow anything to rest on the power cord. Do the machine, squeeze the ends of the rod together not place this product where people may walk on the enough (approximately 1-1/2”) to fit between the cord. 10. If an extension cord is used, be sure that all products back feet on the shredder base. From the back of plugged into the extension cord do not exceed the the machine, slide the rod under the shredder until extension cord ampere rating. it stops. Release the rod to allow it to snap into 11. Do not attempt to service this product yourself, as place, with the ends resting against the shredder opening or removing covers may expose you to feet. Make sure the bag does not block output from dangerous live parts or other risks, and will void the the shredder. warranty. When shredding continuous forms, feed paper 12. Unplug this product and refer servicing to qualified personnel under the following conditions: between the guide and the shredder into the A) When the power cord or plug is damaged or shredder throat. frayed. B) If liquid has been spilled on the product. Parts Identification C) If the product has been exposed to rain. D) If the product does not operate normally when the operating instructions are followed. E) If the product has been dropped or the casing has been damaged. Front 13. Keep out of the reach of children. 14. This shredder should be operated only with an operator in attendance. 15. Do not insert aerosal cleaners into or around the shredder. Some agents may combust, causing serious injury. Bag Support Rod
Wire Form Feed Guide Front Feet
Back Feet Bag
Caution Never insert hand, fingers or any foreign objects into the feed opening. Serious injury may result. Keep all loose articles of clothing, ties, jewelry, long hair or other loose objects away from feed opening. Injury may result. Always turn off and unplug the machine before moving, servicing, cleaning or conducting any activity other than normal operation. Serious injury may result.
Operation Read operating instructions before putting shredder into operation. Insert plug into power outlet.
Prepare paper to be shredded, making sure not to exceed the recommended sheet capacity. Small paper clips will not harm the cutting system, but the added thickness may decrease sheet capacity (see specifications for recommended sheet capacities). Switching shredder ON/FORWARD. Press rocker switch to position (I) (the switch will lock into place.) The cutting system is now running in the forward mode. Insert the paper into throat opening and the cutting system will pull the paper in. Switching shredder OFF. Lightly press rocker switch towards (R) The switch will reset to the OFF position (0) and the cutting system will stop.
Switching shredder to REVERSE. Press rocker switch to position (R) and hold. The cutting system is now running in the reverse direction. Release the switch and it will automatically reset to (0) 0FF.
If a Jam Occurs The cutting system may jam if the recommended capacity is exceeded (see specifications). When this occurs, depress the switch to the REVERSE position (R). This will back out the jammed material. The operator should tear out and remove excess jammed paper, if necessary, and then commence shredding in smaller quantities so as not to further jam the machine.
Maintenance
• No adjustments or maintenance inside of machine is required. • Periodically, unplug shredder to clean dust and debris that may accumulate. • For repairs, call Fellowes Customer Service at 1-800955-0959.
Technical Specifications Cutting Style
Strip
Shred Size
1/4” (5.99mm)
Sheet Capacity 8-1/2 x 11” 20 lb.
16-18
Speed 115V, 60Hz
24 FPM
Entry Width Motor Power 120V
15” (381mm) 1/4 hp
Input voltage 120V 50/60Hz (Depending on country) 220-240v/50Hz Dimensions Inches Millimeters
111/2 H x 219/10 W x 17 D 292 H x 556 W x 431 D
Weight
45 lbs. (20.4 kg)
Reorder bag number
36051
Stand
38915
Supplies
• Five complimentary bags are included with your machine. • Replacement bags are packed 50 to a dispenser carton. • Contact your local Fellowes dealer to order bags that fit your machine. Cutting block oil is not needed on this machine.
Warranty Fellowes Powershred Limited Warranty
1 year on all parts and labor 5 years parts and labor on cutting cylinders Fellowes warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase by the original consumer. At it’s option, Fellowes will repair or replace without charge for material or labor, any component found to be defective during the warranty period. Additionally, the cutting cylinders are warranted for 5 years from the original purchase date and will be replaced without charge for material or labor if found by Fellowes to be defective. Warranty Exclusions
1. When this product or any part thereof has been subjected to accident, alteration, abuse, or misuse. 2. When the shredder's recommended sheet capacity (per specifications on page 5-6) has been exceeded (resulting in a paper jam). 3. When the original Model and Serial Number Plate has been altered, effaced or removed. 4. When repair or service covered under this warranty (other than routine maintenance as described in the Owner's Manual) has been performed by personnel without the express written consent of Fellowes. 5. When the product has been used pursuant to any verbal or written rental, lease or loan agreement. This warranty described herein shall be in lieu of any other warranty, expressed or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. Any representations or promises inconsistent with or in addition to this warranty are unauthorized and shall not be binding upon Fellowes.
The parties agree that the buyer’s sole and exclusive remedy against Fellowes shall be for the repair or replacement of defective parts as provided herein. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to property or any other incidental or consequential loss) shall be available to him. This warranty shall NOT apply and is void under the following circumstances:
Contact For Service: United States Australia Canada Japan Europe
1-800-955-0959 (In Melbourne) (03) 9330-3211 (Outside Melbourne) 1-800-331-177 1-800-665-4339 +81-3-5496-2400 00-800-1810-1810 1789 Norwood Avenue • Itasca, Illinois 60143-1095 630-893-1600 • Customer Service 1-800-955-0959 http://www.fellowes.com
Australia Tullamarine, Victoria
Benelux Vianen, The Netherlands
Canada Markham, Ontario
Deutschland Hanover, Garbsen
France Montanay, Lyon
Italy Via Dante Alighieri, Camerano (An)
Japan Tokyo
United Kingdom Doncaster, South Yorkshire
© 2001 Fellowes Printed in U.S.A. Part No. 30067
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Powershred
®
Table Top Paper Shredder
Operating Instructions
Powerhouse 1000 X
Important Safety Instructions
Installation
1. Read all instructions before use. Unpack your new shredder from its shipping 2. Save these instructions for later use. container. 3. Follow all warnings and instructions marked on the Place the shredder on a table top, desk or the product. optional shredder stand. Be sure the selected work 4. Unplug this product from the wall outlet before surface is strong enough to support the weight of cleaning. Clean with a damp cloth using a mild soap and water solution. (Do not use abrasives or petroleum the shredder. based cleaners.) To attach the wire form feed guide, tilt the shredder 5. Place this product as close as possible to power source back until the front feet lift off the table. Angle the for quick and easy unplugging. Do not block the power wire form feed guide so one “U” curve fits around supply receptacle; it must be possible to conveniently one of the metal tabs. Wrap the other side’s “U” unplug the power cord. curve around the other metal tab. Set the shredder 6. Do not use this product near water. down so the front edge of the guide extends one7. This product should never be placed near or over a half in front of the machine, with the rest of the radiator or heat source. 8. Operate from the type of power source indicated on guide between the shredder and the table. the marking label. If you are not sure of the type of Holding the bag support rod horizontally, pull the power available, consult your dealer or local electricity bag up through the center of the rod and wrap the board. edges of the bag over the rod. To attach the rod to 9. Do not allow anything to rest on the power cord. Do the machine, squeeze the ends of the rod together not place this product where people may walk on the enough (approximately 1-1/2”) to fit between the cord. 10. If an extension cord is used, be sure that all products back feet on the shredder base. From the back of plugged into the extension cord do not exceed the the machine, slide the rod under the shredder until extension cord ampere rating. it stops. Release the rod to allow it to snap into 11. Do not attempt to service this product yourself, as place, with the ends resting against the shredder opening or removing covers may expose you to feet. Make sure the bag does not block output from dangerous live parts or other risks, and will void the the shredder. warranty. When shredding continuous forms, feed paper 12. Unplug this product and refer servicing to qualified personnel under the following conditions: between the guide and the shredder into the A) When the power cord or plug is damaged or shredder throat. frayed. B) If liquid has been spilled on the product. Parts Identification C) If the product has been exposed to rain. D) If the product does not operate normally when the operating instructions are followed. E) If the product has been dropped or the casing has been damaged. Front 13. Keep out of the reach of children. 14. This shredder should be operated only with an operator in attendance. 15. Do not insert aerosal cleaners into or around the shredder. Some agents may combust, causing serious injury. Bag Support Rod
Wire Form Feed Guide Front Feet
Back Feet Bag
Caution Never insert hand, fingers or any foreign objects into the feed opening. Serious injury may result. Keep all loose articles of clothing, ties, jewelry, long hair or other loose objects away from feed opening. Injury may result. Always turn off and unplug the machine before moving, servicing, cleaning or conducting any activity other than normal operation. Serious injury may result.
Operation Read operating instructions before putting shredder into operation. Insert plug into power outlet.
Prepare paper to be shredded, making sure not to exceed the recommended sheet capacity. Small paper clips will not harm the cutting system, but the added thickness may decrease sheet capacity (see specifications for recommended sheet capacities). Switching shredder ON/FORWARD. Press rocker switch to position (I) (the switch will lock into place.) The cutting system is now running in the forward mode. Insert the paper into throat opening and the cutting system will pull the paper in. Switching shredder OFF. Lightly press rocker switch towards (R) The switch will reset to the OFF position (0) and the cutting system will stop.
Switching shredder to REVERSE. Press rocker switch to position (R) and hold. The cutting system is now running in the reverse direction. Release the switch and it will automatically reset to (0) 0FF.
If a Jam Occurs The cutting system may jam if the recommended capacity is exceeded (see specifications). When this occurs, depress the switch to the REVERSE position (R). This will back out the jammed material. The operator should tear out and remove excess jammed paper, if necessary, and then commence shredding in smaller quantities so as not to further jam the machine.
Maintenance
• No adjustments or maintenance inside of machine is required. • Periodically, unplug shredder to clean dust and debris that may accumulate. • For repairs, call Fellowes Customer Service at 1-800955-0959.
Technical Specifications Cutting Style
Strip
Shred Size
1/4” (5.99mm)
Sheet Capacity 8-1/2 x 11” 20 lb.
16-18
Speed 115V, 60Hz
24 FPM
Entry Width Motor Power 120V
15” (381mm) 1/4 hp
Input voltage 120V 50/60Hz (Depending on country) 220-240v/50Hz Dimensions Inches Millimeters
111/2 H x 219/10 W x 17 D 292 H x 556 W x 431 D
Weight
45 lbs. (20.4 kg)
Reorder bag number
36051
Stand
38915
Supplies
• Five complimentary bags are included with your machine. • Replacement bags are packed 50 to a dispenser carton. • Contact your local Fellowes dealer to order bags that fit your machine. Cutting block oil is not needed on this machine.
Warranty Fellowes Powershred Limited Warranty
1 year on all parts and labor 5 years parts and labor on cutting cylinders Fellowes warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase by the original consumer. At it’s option, Fellowes will repair or replace without charge for material or labor, any component found to be defective during the warranty period. Additionally, the cutting cylinders are warranted for 5 years from the original purchase date and will be replaced without charge for material or labor if found by Fellowes to be defective. Warranty Exclusions
1. When this product or any part thereof has been subjected to accident, alteration, abuse, or misuse. 2. When the shredder's recommended sheet capacity (per specifications on page 5-6) has been exceeded (resulting in a paper jam). 3. When the original Model and Serial Number Plate has been altered, effaced or removed. 4. When repair or service covered under this warranty (other than routine maintenance as described in the Owner's Manual) has been performed by personnel without the express written consent of Fellowes. 5. When the product has been used pursuant to any verbal or written rental, lease or loan agreement. This warranty described herein shall be in lieu of any other warranty, expressed or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. Any representations or promises inconsistent with or in addition to this warranty are unauthorized and shall not be binding upon Fellowes.
The parties agree that the buyer’s sole and exclusive remedy against Fellowes shall be for the repair or replacement of defective parts as provided herein. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to property or any other incidental or consequential loss) shall be available to him. This warranty shall NOT apply and is void under the following circumstances:
Contact For Service: United States Australia Canada Japan Europe
1-800-955-0959 (In Melbourne) (03) 9330-3211 (Outside Melbourne) 1-800-331-177 1-800-665-4339 +81-3-5496-2400 00-800-1810-1810 1789 Norwood Avenue • Itasca, Illinois 60143-1095 630-893-1600 • Customer Service 1-800-955-0959 http://www.fellowes.com
Australia Tullamarine, Victoria
Benelux Vianen, The Netherlands
Canada Markham, Ontario
Deutschland Hanover, Garbsen
France Montanay, Lyon
Italy Via Dante Alighieri, Camerano (An)
Japan Tokyo
United Kingdom Doncaster, South Yorkshire
© 2001 Fellowes Printed in U.S.A. Part No. 30067
