Fittings
Fittings This section offers a full selection of fittings and accessories to complete our strut system. Fittings are made from hot rolled, pickled and oiled plate or strip steel in accordance with ASTM A1018 33,000 PSI min. yield, unless noted.
Dimensions The following dimensions apply to all fittings except as noted: Hole Spacing – 17/8” (47.6 mm) on center Hole Spacing –
13/16” (20.6 mm)
Hole Size – 9/16” (14.3 mm) diameter
from end
Thickness – 7/32” (5.5 mm) Width – 15/8” (41.3 mm)
Materials & Finishes (Unless otherwise noted) Finish Code PLN
Finish Plain
ZN
Electro-Plated Zinc
GRN HDG SS4 SS6 AL
DURA-GREEN™ Hot-Dipped Galvanized Stainless Steel Type 304 Stainless Steel Type 316 Aluminum
Specification ASTM A1018 33,000 PSI min. yield ASTM B633 SC3 Type III or ASTM A653 ASTM A123 ASTM A240 ASTM A240 ASTM B209
Note: A minimum order may apply on special material and finishes.
Load Data The load data published includes safety factor of 2.5 when used with 12 ga. (2.6) channel (safety factor = ratio of ultimate load to the design load). Use 1/2”-13 x 7/8” hex head cap screws and 1/2”-13 (N225 or TN225) channel nuts for the rated results.
Recommended Bolt Torque Bolt Size
1/4”-20
5/16”-18
3/8”-16
1/2”-13
Foot/Lbs.
6
11
19
50
Nm
8
15
26
68
Strut Fittings
See chart on page 112 for setscrew torque.
Hardware Nuts and bolts are not included with the fittings and must be ordered separately, unless noted.
Pre-Assembled Fittings Some fittings are available with hex head cap screws and channel nuts pre-assembled. These fittings and finishes will be flagged using the following symbol. ZN
PA
GRN
Metric Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.
72
Strut Systems
Flat Plate Fittings B200-B202-2
SQUARE WASHER
• Standard finishes: ZN, GRN, HDG, SS4, SS6, AL
Part No. B200 B201 B202 B202-1 B202-2
15/8” (41.3)
Hole Size
A
B129 TWO HOLE SPLICE PLATE
Wt./C A 3/8” 7/16” 9/16” 11/16” 13/16”
(A) (9.5) (11.1) (14.2) (17.4) (20.6)
Bolt Size 5/16” (7.9) 3/8” (9.5) 1/2” (12.7) 5/8” (15.9) 3/4” (19.0)
Lbs.
kg
18 18 17 16 15
(8.1) (8.1)
• Standard finishes: ZN, GRN • Wt./C 37 Lbs. (16.8 kg)
PA
ZN GRN
(7.7) (7.2)
31/2”
(6.8)
(88.9)
B200D-B202-2D
NO TWIST SQUARE WASHER
• Standard finishes: ZN, GRN, HDG, SS4, SS6, AL
Part No. B200D B201D B202D B202-1D B202-2D
15/8” (41.3)
A
Hole Size
Wt./C A
(A)
Bolt Size
3/8”
(9.5)
5/16”
7/16”
(11.1)
3/8”
(9.5)
9/16”
(14.2)
1/2”
(12.7)
11/16” (17.4) 13/16” (20.6)
5/8”
(15.9)
3/4”
(19.0)
(7.9)
Lbs.
kg
18 18 17 16 15
(8.1) (8.1) (7.7) (7.2) (6.8)
B340
B528
B141
TWO HOLE SPLICE PLATE
TWO HOLE SPLICE PLATE
THREE HOLE SPLICE PLATE
• Standard finishes: ZN, GRN • Wt./C 34 Lbs. (15.4 kg)
• Standard finishes: ZN, GRN • Wt./C 50 Lbs. (22.7 kg)
• Standard finishes: ZN, GRN • Wt./C 55 Lbs. (24.9 kg)
PA 15/16”
15/8” (41.3)
ZN GRN
21/2”
53/8” (136.5)
(63.5)
(33.3)
31/4” (82.5)
45/8” (117.5)
B557
B341
B342
THREE HOLE SPLICE PLATE
FOUR HOLE SPLICE PLATE
FIVE HOLE SPLICE PLATE
• Standard finishes: ZN, GRN • Wt./C 50 Lbs. (22.7 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN • Wt./C 96 Lbs. (43.5 kg)
PA
47/8”
ZN GRN
(123.8)
71/4”
15/8”
15/8” (41.3)
(41.3)
PA Reference page 72 for general fitting and standard finish specifications.
Strut Systems
Strut Fittings
(184.1)
91/8” (231.8)
73
Preassembled fitting.
Flat Plate Fittings B138
B139
B504
TWO HOLE SWIVEL PLATE
THREE HOLE SWIVEL PLATE
FOUR HOLE SPLICE PLATE
• Standard finishes: ZN, GRN • Wt./C 48 Lbs. (21.8 kg)
• Standard finishes: ZN, GRN • Wt./C 69 Lbs. (31.3 kg)
• Standard finishes: ZN, GRN • Wt./C 73 Lbs. (33.1 kg)
45/8” (117.5)
61/2” (165.1)
3” (76.2)
17/8”
15/8”
31/2”
(41.3)
(88.9)
3”
31/4”
(76.2)
(82.5)
(47.6)
B140
B143
B133
THREE HOLE CORNER PLATE
FOUR HOLE CORNER PLATE
FOUR HOLE TEE PLATE
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 56 Lbs. (25.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 75 Lbs. (34.0 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 75 Lbs. (34.0 kg)
PA
ZN GRN
PA
ZN GRN
PA
31/2”
ZN GRN
31/2” (88.9)
(88.9)
31/2” (88.9)
53/8” (136.5)
31/2” (88.9)
53/8” (136.5)
B132
B135
B142
FIVE HOLE CROSS PLATE
THREE HOLE CORNER GUSSET PLATE
FOUR HOLE CORNER GUSSET PLATE
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 102 Lbs. (46.2 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
PA
ZN GRN
PA 53/8” (136.5)
ZN GRN
31/2” 31/2”
Strut Fittings
(88.9)
(88.9)
31/2 (88.9) 53/8” (136.5)
53/8”
PA
Preassembled fitting. Reference page 72 for general fitting and standard finish specifications.
74
Strut Systems
Flat Plate Fittings B137
B556
B337
FOUR HOLE CORNER GUSSET PLATE
FIVE HOLE CORNER GUSSET PLATE
THREE HOLE TEE GUSSET PLATE
• Standard finishes: ZN, GRN • Wt./C 273 Lbs. (123.8 kg)
• Standard finishes: ZN, GRN • Wt./C 145 Lbs. (65.8 kg)
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
75/8”
25/16” (58.7)
(193.7) 13 5 /16” (147.6)
1”
31/2”
53/8” 75/8” (193.7)
(25.4)
(88.9)
(136.5)
53/8” (136.5)
31/2”
31/2”
(88.9)
(88.9)
1” (25.4)
B432
B136
B532
FOUR HOLE TEE GUSSET PLATE FOUR HOLE TEE GUSSET PLATE FIVE HOLE TEE GUSSET PLATE • Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 143 Lbs. (64.8 kg)
31/2”
31/2”
(88.9)
(88.9)
53/8” (136.5)
53/8” (136.5)
53/8” (136.5) 53/8” (136.5)
B339
B568
B334
SIX HOLE TEE GUSSET PLATE
SIX HOLE CROSS GUSSET PLATE
SEVEN HOLE CROSS GUSSET PLATE
• Standard finishes: ZN, GRN • Wt./C 166 Lbs. (75.3 kg)
• Standard finishes: ZN, GRN • Wt./C 232 Lbs. (105.2 kg)
• Standard finishes: ZN, GRN • Wt./C 149 Lbs. (67.6 kg)
31/2” (88.9)
91/8” (231.8)
91/8” (231.8)
31/2”
53/8” (136.5)
(88.9)
Reference page 75 for general fitting and standard finish specifications. Strut Systems
75
Strut Fittings
91/8” (231.8)
90° Angle Fittings B420-378
B420-578
B420-778
ONE HOLE CORNER ANGLE
ONE HOLE CORNER ANGLE
ONE HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 60 Lbs. (27.2 kg)
• Standard finishes: ZN, GRN • Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN • Wt./C 107 Lbs. (48.5 kg)
17/8” 17/8”
17/8”
(47.6)
(47.6)
(47.6)
77/8” (200.0)
57/8” (149.2)
37/8” (98.4)
B420-978
B101
B230
ONE HOLE CORNER ANGLE
TWO HOLE CORNER ANGLE
TWO HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 129 Lbs. (58.5 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 37 Lbs. (16.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 37 Lbs. (16.8 kg)
PA
ZN GRN
PA
15/8”
ZN GRN
17/8”
(41.3)
17/8”
(47.6)
(47.6)
97/8” (250.8)
21/16” (52.4)
25/16” (58.7)
B231
B359
B360
TWO HOLE “NO-TWIST” CORNER ANGLE
TWO HOLE CORNER ANGLE
TWO HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 48 Lbs. (21.8 kg)
• Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 41 Lbs. (18.6 kg)
PA
ZN GRN
Strut Fittings
3”
31/2”
(76.2)
(88.9)
21/4” (57.1)
21/4”
17/8”
(57.1)
PA
(47.6)
17/8” (47.6)
Preassembled fitting. Reference page 72 for general fitting and standard finish specifications.
76
Strut Systems
90° Angle Fittings B361
B102
B103
TWO HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 60 Lbs. (27.2 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 56 Lbs. (25.4 kg) • Wt./C 56 Lbs. (25.4 kg)
PA
ZN GRN
ZN GRN
PA
15/8”
31/2”
4”
(41.3)
(88.9)
(101.6)
41/8” (104.8)
17/8”
21/4”
(47.6)
(57.1)
B232
B374
B529
THREE HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
• Standard finishes: ZN, GRN, HDG, SS4 • Standard finishes: ZN, GRN, HDG • Wt./C 56 Lbs. (25.4 kg) • Wt./C 56 Lbs. (25.4 kg)
PA
ZN GRN
PA
ZN GRN
• Standard finishes: ZN, GRN • Wt./C 78 Lbs. (35.4 kg)
3”
21/16” 15/16”
(52.4)
(76.2)
(33.3)
17/8” (47.6)
47/8” (123.8)
315/16”
33/4”
(100.0)
(95.2)
15/16” (33.3)
21/2” (63.5)
B104
B115
B558
FOUR HOLE CORNER ANGLE
FOUR HOLE CORNER ANGLE
FOUR HOLE CORNER ANGLE
• Standard finishes: ZN, GRN, HDG, SS4, SS6, AL • Wt./C 78 Lbs. (35.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN • Wt./C 73 Lbs. (33.1 kg)
PA
ZN GRN
PA 31/2”
ZN GRN
15/8” (41.3)
33/4” (95.2)
(88.9)
Strut Fittings
21/4” (57.1)
41/8” (104.8) 315/16” (100.0)
15/8”
31/4”
(41.3)
(82.5)
PA Reference page 72 for general fitting and standard finish specifications. Strut Systems
77
Preassembled fitting.
90° Angle Fittings B235R
B235L
B236R
THREE HOLE (RIGHT HAND) OFFSET BENT ANGLE
THREE HOLE (LEFT HAND) OFFSET BENT ANGLE
THREE HOLE (RIGHT HAND) OFFSET BENT ANGLE
• 15/8” (41.3) from center to center of the holes that are shown with bolt heads • Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• 15/8” (41.3) from center to center of the holes that are shown with bolt heads • Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN • Wt./C 65 Lbs. (29.5 kg)
17/8”
31/4”
31/4”
17/8”
(47.6)
(82.5)
(82.5)
(47.6)
21/16” (52.4)
17/8”
31/2”
(47.6)
21/16”
21/16”
(52.4)
(52.4)
(88.9)
B236L
B237
B357
THREE HOLE (LEFT HAND) OFFSET BENT ANGLE
THREE HOLE OFFSET BENT TEE
FOUR HOLE OFFSET BENT TEE
• Standard finishes: ZN, GRN • Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN, GRN • Wt./C 77 Lbs. (34.9 kg)
• Standard finishes: ZN, GRN • Wt./C 65 Lbs. (29.5 kg)
47/8” (123.8)
17/8”
31/2”
2”
(47.6)
(88.9)
21/16”
(50.8)
(52.4)
53/8” (136.5)
21/16”
Strut Fittings
(52.4)
B238R
B238L
B239
FOUR HOLE (RIGHT HAND) OFFSET BENT TEE
FOUR HOLE (LEFT HAND) OFFSET BENT TEE
FIVE HOLE OFFSET BENT TEE
• Standard finishes: ZN, GRN • Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN • Wt./C 76 Lbs. (34.5 kg)
21/16”
21/16”
(52.4)
(52.4)
• Standard finishes: ZN, GRN • Wt./C 96 Lbs. (43.5 kg)
21/16” (52.4)
33/4” (95.2)
31/2”
31/2”
(88.9)
(88.9)
53/8” (136.5)
33/4”
31/2”
(95.2)
(88.9)
Reference page 72 for general fitting and standard finish specifications.
78
Strut Systems
90° Angle Fittings B844
B844W
B888W
UNIVERSAL SHELF BRACKET
UNIVERSAL SHELF BRACKET• Standard finishes: ZN, GRN, HDG, SS4 WELDED
UNIVERSAL SHELF BRACKETWELDED
• Wt./C 132 Lbs. (59.9 kg)
• Standard finishes: ZN, GRN • Wt./C 197 Lbs. (89.4 kg)
• Standard finishes: ZN, GRN • Wt./C 134 Lbs. (60.8 kg)
4”
4”
(101.6)
(101.6)
513/16” (147.6) Welded Corner
17/8” (47.6)
4”
4”
(101.6)
(101.6)
17/8”
17/8”
(47.6)
(47.6)
53/8” (136.5)
B234R
B234L
B134R
FOUR HOLE (RIGHT HAND) CORNER GUSSET
FOUR HOLE (LEFT HAND) CORNER GUSSET
FOUR HOLE (RIGHT HAND) CORNER GUSSET
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
31/2” 15/8”
(88.9)
31/2” (88.9)
315/16”
15/8”
(100.0)
(41.3)
(41.3)
31/2” (88.9)
43/16”
43/16”
(106.3)
(106.3)
17/8” (47.6)
B134L
B125
B118
FOUR HOLE (LEFT HAND) CORNER GUSSET
THREE HOLE GUSSETTED SHELF ANGLE
FOUR HOLE GUSSETTED SHELF ANGLE
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 67 Lbs. (30.4 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 102 Lbs. (46.2 kg)
315/16”
31/2” 31/2”
(88.9)
15/8”
(88.9)
31/2”
15/8”
(88.9)
(41.3)
25/16” (58.7)
17/8” (47.6)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
79
(41.3)
41/8” (104.8)
Strut Fittings
(100.0)
90° Angle Fittings B485
B533
B126
FOUR HOLE GUSSETTED SHELF ANGLE
FIVE HOLE GUSSETTED SHELF ANGLE
FOUR HOLE GUSSETTED THREE WAY SHELF ANGLE
• Standard finishes: ZN, GRN • Wt./C 148 Lbs. (67.1 kg)
• Standard finishes: ZN, GRN • Wt./C 141 Lbs. (63.9 kg)
• Standard finishes: ZN, GRN • Wt./C 101 Lbs. (45.8 kg)
17/8” 15/8”
(47.6)
(41.3)
31/2”
41/8”
(88.9)
(104.8)
31/2” (88.9)
21/4”
53/8”
53/8”
(136.5)
(57.1)
(136.5)
315/16” (100.0)
B127
B503R
B503L
FIVE HOLE GUSSETTED THREE WAY SHELF ANGLE
SIX HOLE (RIGHT HAND) GUSSETTED CORNER CONNECTION
SIX HOLE (LEFT HAND) GUSSETTED CORNER CONNECTION
• Standard finishes: ZN, GRN • Wt./C 229 Lbs. (103.9 kg)
• Standard finishes: ZN, GRN • Wt./C 229 Lbs. (103.9 kg)
• Standard finishes: ZN, GRN • Wt./C 135 Lbs. (61.2 kg)
31/2”
33/4”
(88.9)
(95.2)
31/2” (88.9)
33/4”
43/16” 43/16”
(95.2)
43/16”
(106.3)
(106.3)
(106.3)
53/8” (136.5)
53/8” (136.5)
15/8”
15/8”
(41.3)
(41.3)
B663
B371
B372
SEVEN HOLE GUSSETTED CORNER CONNECTION
TWO HOLE ADJUSTABLE CORNER ANGLE • Standard finishes: ZN, GRN • Wt./C 41 Lbs. (18.6 kg)
TWO HOLE ADJUSTABLE CORNER ANGLE • Standard finishes: ZN, GRN • Wt./C 38 Lbs. (17.2 kg)
• Standard finishes: ZN, GRN • Wt./C 289 Lbs. (131.1 kg)
53/8” (136.5)
Strut Fittings
25/8” 53/8”
43/16”
(136.5)
25/8”
(66.7)
(66.7)
(106.3)
9/16”
9/16”
(14.3) 9/16”
(14.3)
x 11/2”
Slot
(50.8)
(38.1)
(14.3)
2” 9/16”
(14.3)
x 11/2”
Slot
(38.1)
15/8” (41.3)
15/8” (41.3)
Reference page 72 for general fitting and standard finish specifications.
80
Strut Systems
90° Angle Fittings B496
B496-1
B371-2
TWO HOLE ADJUSTABLE CORNER ANGLE • Standard finishes: ZN, GRN • Wt./C 85 Lbs. (38.5 kg)
TWO HOLE ADJUSTABLE CORNER ANGLE
THREE HOLE ADJUSTABLE CORNER ANGLE
• Standard finishes: ZN, GRN, HDG • Wt./C 58 Lbs. (26.3 kg)
• Standard finishes: ZN, GRN • Wt./C 61 Lbs. (27.6 kg)
23/8”
23/8”
(60.3)
(60.3)
15/16”
47/8”
67/8”
(33.3) 9/16”
(123.8)
(174.6) 9/16”
x 29/16”
(14.3)
(65.1)
Slot
17/8”
17/8”
(47.6)
(47.6)
9/16”
x 29/16”
(14.3)
(65.1)
(14.3)
x 11/2”
Slot
25/8”
(38.1)
Slot
(66.7)
37/8” (98.4)
B104SH
B461
B112
THREE HOLE ADJUSTABLE CORNER ANGLE
TWO HOLE ADJUSTABLE CORNER ANGLE
FOUR HOLE ADJUSTABLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 68 Lbs. (30.8 kg)
• Standard finishes: ZN, GRN • Wt./C 87 Lbs. (39.4 kg)
• Standard finishes: ZN, GRN • Wt./C 180 Lbs. (81.6 kg)
31/2”
31/2”
(88.9)
(88.9)
21/4” (57.1) 9/16”
1/2” (12.7)
13/32” (10.3)
31/2” (88.9)
9/16”
x 29/16”
(14.3)
(65.1)
Slot
41/8” (104.8)
9/16”
x 29/16”
(14.3)
(65.1)
x 11/2”
(14.3)
Slot -(2)
(38.1)
33/4” (95.2)
4” (101.6)
Slot
65/8” (168.3)
B113
B109S
B521
FOUR HOLE ADJUSTABLE CORNER ANGLE
TWO HOLE TAPPED CORNER ANGLE
TWO HOLE BUS DUCT ANGLE
• Standard finishes: ZN, GRN • Wt./C 256 Lbs. (116.1 kg)
• Standard finishes: ZN, GRN • Wt./C 33 Lbs. (14.9 kg)
x 11/2”
(14.3)
Slot -(2)
(38.1)
33/4”
5/16”-18 Tapped
17/8”
(95.2)
1/2” (12.7)
17/8” (47.6)
(47.6)
6” (152.4)
15/8” 85/8” (219.1)
(41.3)
17/8” (47.6)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
2” (50.8)
81
Strut Fittings
9/16”
• Standard finishes: ZN, GRN • Wt./C 37 Lbs. (16.8 kg)
Angular Fittings B147-B152
B243-B253
TWO HOLE OPEN ANGLE
FOUR HOLE OPEN ANGLE
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
23/8” (60.3)
11/16” (27.0)
Part No.
A
B147 B148 B149 B150 B151 B152
821/2°
Wt./C Lbs.
75° 671/2° 60° 521/2° 371/2°
31/4” A
kg
(82.5)
11/16” (27.0)
63
(28.6)
B162-B165
A
(27.0)
35/16” (84.1)
B162 B163 B164 B165
30° 221/2° 15° 71/2°
Wt./C kg
11/16”
21/16” (52.4)
(27.0)
59
15° 221/2° 30° 371/2° 45° 521/2° 60° 671/2° 75° 821/2°
kg
311/16” (93.6)
A
31/2” 77
(34.9)
(88.9)
• Standard finishes: ZN, GRN
11/16”
Lbs.
B243 B244 B245 B246 B247 B248 B249 B250 B251 B252 B253
71/2°
Wt./C Lbs.
TWO HOLE OPEN SHORT ANGLE
• Standard finishes: ZN, GRN
A
A
B322-B332
TWO HOLE OPEN ANGLE
Part No.
Part No.
(26.7)
B154 TWO HOLE OPEN ANGLE • Standard finishes: ZN, GRN, SS4 • Wt./C 58 Lbs. (26.3 kg)
Part No.
A
B322 B323 B324 B325 B326 B327 B328 B329 B330 B331 B332
71/2°
Wt./C Lbs.
15° 221/2° 30° 371/2° 45° 521/2° 60° 671/2° 75° 821/2°
kg
A 13/4” (44.4)
15/8” (41.3)
35
(15.9)
B522
B488
THREE HOLE 95° OPEN ANGLE FITTING
TWO HOLE LEG CONNECTION
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
Strut Fittings
17/8” (47.6)
3” (76.2)
5° 5°
5°
11/16” (27.0)
25/16” 45°
(58.7)
11/16”
35/8” (92.1)
31/4”
(27.0)
(82.5)
Reference page 72 for general fitting and standard finish specifications.
82
Strut Systems
Angular Fittings B156 - B161
B155
TWO HOLE CLOSED ANGLE
TWO HOLE CLOSED ANGLE
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 63 Lbs. (28.6 kg)
PA Part No.
A
B156 B157 B158 B159 B160 B161
821/2° 75° 671/2° 60° 521/2° 371/2°
13/16”
13/16”
(20.6)
(20.6)
Wt./C Lbs.
ZN GRN
33/16”
kg
31/2” (88.9)
(80.9) 13/16”
45°
(20.6)
56
(25.4)
A 13/16”
21/2”
(20.6)
21/2”
(63.5)
(63.5)
B363 - B369
B335-2 SERIES
FOUR HOLE CLOSED ANGLE
THREE HOLE ADJUSTABLE HINGE
• Standard finishes: ZN, GRN
• OSHPD approved for Seismic Zone 4 • Standard finishes: ZN, GRN
5”
H
(127.0)
Hole Size This Hole Only
Part No.
A
B363 B364 B365 B366 B367 B368 B369
821/2° 75° 671/2° 60° 521/2° 45° 371/2°
411/16”
Wt./C Lbs.
(119.1)
kg
43/8”
213/16”
(111.1)
(71.4)
95
(43.1)
Part No. & Size B335-2-3/8 B335-2-1/2 B335-2-5/8 B335-2-3/4
A
Hole Size H 7/16” (11.1) 9/16” (14.3) 11/16” (17.4) 13/16” (20.6)
Wt./C Lbs.
kg
96 94 92 90
(43.2) (42.3) (41.4) (40.5)
B335
B335V
B335-1
FOUR HOLE ADJUSTABLE HINGE
TWO HOLE HALF HINGE
TWO HOLE ADJUSTABLE HINGE
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN • Wt./C 78 Lbs. (35.4 kg)
• Standard finishes: ZN, GRN • Wt./C 110 Lbs. (49.9 kg)
411/16” (119.1)
Hole Size H 9/16” (14.3) 11/16” (17.4) 13/16” (20.6)
Wt./C Lbs.
kg
53 54 55
(24.1) (24.5) (24.9)
213/16”
H
(71.4)
Strut Fittings
Part No. & Size B335V-1/2 B335V-5/8 B335V-3/4
213/16” (71.4)
411/16”
411/16”
(119.1)
(119.1)
PA Reference page 72 for general fitting and standard finish specifications. Strut Systems
83
Preassembled fitting.
Angular Fittings B634
B635
SINGLE CHANNEL ADJUSTABLE BRACE
DOUBLE CHANNEL ADJUSTABLE BRACE
• Standard finishes: ZN, GRN • Wt./C 306 Lbs. (138.8 kg)
• Standard finishes: ZN, GRN • Wt./C 518 Lbs. (234.9 kg)
13/16”
13/16”
(20.6)
(20.6)
15/8”
15/8”
(41.3)
(41.3)
30° MIN.
17/8”
17/8”
(47.6)
(47.6)
33/4”
33/4”
(95.2) 53/8”
(95.2) 53/8”
(136.5)
(136.5)
B129
B650 SERIES SEISMIC RETROFIT BRACKET • • • • •
OSHPD approved for Seismic Zone 4. Available for 3/8”, 1/2”, 5/8”, and 3/4” threaded rods. Allows installer to easily brace existing trapeze supports. Includes: Bracket, B129 plate, & key. Hardware sold separately. Standard finish: ZN, GRN
ATR
Bracket
Key Part No. & Size
For Rod Size
B650-3/8
3/8”
B650-1/2 B650-5/8 B650-3/4
1/2” 5/8” 3/4”
TL
LL
Wt./C
Lbs.
kN
Lbs.
kN
Lbs.
kg
1100 1500 1500 1500
(4.89)
1100 1500 1500 1500
(4.89)
92 97 95 107
(41.4)
(6.67) (6.67) (6.67)
(6.67) (6.67) (6.67)
Longitudina l Load (LL)
(43.6) (42.7)
Transverse Load (TL)
(48.5)
B633 ADJUSTABLE SEISMIC HINGE FITTING
Strut Fittings
• B633-1/2 thru B633-7/8 - OSHPD approved for Seismic Zone 4. • Use 1/2” Bolt & Channel Nut on two hole side of Connector Fitting (Torque to 50 ft.-lbs.) • Allows for swivel in two planes. • Standard finish: ZN
H 33/4” (95.2)
B
15/8” (41.3)
Part No. & Size
A
B633-1/2
31/2”
B633-5/8 B633-3/4 B633-7/8 B633-1 B633-11/8 B633-11/4
31/2” 31/2” 39/16” 39/16” 39/16” 37/8”
Hole Size H
B (82.5)
15/8”
(82.5)
15/8” 15/8” 2” 2” 2” 21/4”
(82.5) (90.5) (90.5) (90.5) (98.4)
(41.3)
9/16”
(14.3)
(41.3)
11/16”
(17.4)
(41.3)
13/16”
(20.6)
(50.8)
15/16”
(23.8)
(50.8) 11/16”
(27.0)
13/16”
(30.2)
(57.1) 15/16”
(33.3)
(50.8)
Wt./C Lbs.
kg
92 97 95 107 120 104 114
(41.4)
A
(43.6) (42.7) (48.5) (54.0) (47.2) (51.7)
Reference page 72 for general fitting and standard finish specifications.
84
Strut Systems
Braces B261 - TWO HOLE 45° KNEE BRACE • Standard finishes: ZN, GRN • Design load determined by testing using a B335 hinged corner connection. • Load ratings are for brace members only. Do not exceed allowable beam or column loads for strut channels. • Safety Factor of 3 Part No. B261-8 B261-12 B261-16 B261-18 B261-24 B261-36
Design Load A 8” 12” 165/8” 18” 24” 36”
B
(B)
Lbs.
kN
Lbs.
kg
(203.2)
73/8”
(187.3)
1500 1020 530 450 250 110
(6.67)
119 165 218 234 303 441
(54.0)
(422.3) 133/8” (339.7) (457.2) 147/16” (366.7) (609.6) 1811/16” (474.7) (914.4) 273/16” (690.6)
(4.54) (2.36) (2.00) (1.11) (.49)
(41.3)
Design Load
(74.8) (98.9)
B A
Wt./C
(A)
(304.8) 101/8” (257.2)
15/8”
45°
15/8” (41.3)
(106.1) (137.4)
B
(200.0)
B631 - TWO HOLE 45° TUBING KNEE BRACE • • • • •
1” (25.4) Square steel tubing Material: ASTM A513 Standard finishes: ZN, GRN Design load determined by testing using a B335 hinged corner connection. Load ratings are for brace members only. Do not exceed allowable beam or column loads for strut channels. • Safety Factor of 3 Design Load
Part No.
A
B631-18 B631-24 B631-30 B631-36 B631-42 B631-48 B631-54 B631-60 B631-72 B631-84 B631-96
18” 24” 30” 36” 42” 48” 54” 60” 72” 84” 96”
(A) (457.2) (609.6) (762.0) (914.4) (1066.8) (1219.2) (1371.6) (1524.0) (1828.8) (2133.6) (2438.4)
kN
Lbs.
kg
1500 1500 1500 1500 1230 940 740 600 420 310 240
(6.67)
145 186 225 266 307 348 389 430 508 589 669
(65.8)
(6.67) (6.67) (5.47) (4.18) (3.29) (2.67) (1.87) (1.38) (1.07)
A
Wt./C
Lbs.
(6.67)
Design Load
(84.4) (102.0) (120.6) (139.2) (157.8) (176.4) (195.0) (230.4)
13/4”
(267.2)
(44.4)
(303.5)
B632 - TWO HOLE STRAIGHT TUBING BRACE • 1” (25.4) Square steel tubing • Material: ASTM A513 • Standard finishes: ZN, GRN
A
(A)
Lbs.
Wt./C kg
B632-18 B632-24 B632-30 B632-36 B632-42 B632-48 B632-54 B632-60 B632-72 B632-84 B632-96
18” 24” 30” 36” 42” 48” 54” 60” 72” 84” 96”
(457.2)
133 174 215 256 295 335 380 420 500 585 670
(60.3)
13/4”
(78.9)
(44.4)
(609.6) (762.0) (914.4) (1066.8) (1219.2) (1371.6) (1524.0) (1828.8) (2133.6) (2438.4)
(97.5) (116.1) (133.8)
A
(151.9) (172.3) (190.5) (226.8) (265.3) (303.9)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
85
Strut Fittings
Part No.
Clevis Fittings B169
B168
B167
TWO HOLE SPLICE CLEVIS FOR B52
THREE HOLE SPLICE CLEVIS FOR B52
FOUR HOLE SPLICE CLEVIS FOR B52
• Standard finishes: ZN, GRN • Wt./C 84 Lbs. (38.1 kg)
• Standard finishes: ZN, GRN • Wt./C 126 Lbs. (57.1 kg)
• Standard finishes: ZN, GRN • Wt./C 178 Lbs. (80.7 kg)
PA
31/2” 1/4”
GRN
71/4” (184.1)
53/8”
(88.9)
(136.5) 1/4”
(6.3)
1/4”
(6.3)
(6.3)
B170
B171
B172
TWO HOLE SPLICE CLEVIS FOR B22 OR B52A
THREE HOLE SPLICE CLEVIS FOR B22 OR B52A
FOUR HOLE SPLICE CLEVIS FOR B22 OR B52A
• Standard finishes: ZN, GRN • Wt./C 123 Lbs. (55.8 kg)
• Standard finishes: ZN, GRN • Wt./C 195 Lbs. (88.4 kg)
• Standard finishes: ZN, GRN • Wt./C 266 Lbs. (120.6 kg)
PA
31/2” 1/4”
ZN GRN
53/8” (136.5)
(88.9)
(6.3)
71/4” (184.1)
1/4”
1/4”
(6.3)
(6.3)
B172-12
B172-22A
B450
FOUR HOLE SPLICE CLEVIS FOR B12
FOUR HOLE SPLICE CLEVIS FOR B11 OR B22A
U-WASHER
• Standard finishes: ZN, GRN • Wt./C 326 Lbs. (147.8 kg)
• Standard finishes: ZN, GRN • Wt./C 406 Lbs. (184.1 kg)
PA
• Material: ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN
H
GRN
Hole Size 15/32” (11.9)
Strut Fittings
15/8” 11 Gauge (3.1)
Part No. & Size
71/4”
71/4” (184.1)
(184.1) 1/4” (6.3)
1/4” (6.3)
PA
(41.3)
Hole Size H
B450-1/4
5/16”
B450-3/8 B450-1/2 B450-5/8 B450-3/4
7/16” (11.1) 9/16” (14.3)
(7.9)
11/16” (17.4) 13/16” (20.6)
Wt./C Lbs.
kg
14 14 13 13 13
(6.3) (6.3) (5.8) (5.8) (5.8)
Preassembled fitting. Reference page 72 for general fitting and standard finish specifications.
86
Strut Systems
‘U’ Fittings B527
B116-52
B116-42
THREE HOLE OFFSET PLATE CONNECTION
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN • Wt./C 75 Lbs. (34.0 kg)
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
1/2” (12.7)
13/16”
1”
(20.6)
(25.4)
57/16”
57/16”
(138.1)
(138.1)
55/16” (134.9)
B116-32
B116-32A
B116-12
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 84 Lbs. (38.1 kg)
• Standard finishes: ZN, GRN • Wt./C 116 Lbs. (52.6 kg)
• Standard finishes: ZN, GRN • Wt./C 108 Lbs. (49.0 kg)
13/8”
23/4”
27/16”
(69.8)
(61.9)
(34.9)
57/16”
57/16”
57/16”
(138.1)
(138.1)
(138.1)
B107
B107-22A
B588
FIVE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
• Standard finishes: ZN, GRN, HDG • Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN • Wt./C 126 Lbs. (57.1 kg)
• Standard finishes: ZN, GRN • Wt./C 157 Lbs. (71.2 kg)
PA
ZN GRN
15/8”
47/8” (123.8)
Strut Fittings
31/4” (82.5)
(41.3)
57/16” (138.1)
57/16” (138.1)
57/16” (138.1)
PA Reference page 72 for general fitting and standard finish specifications. Strut Systems
87
Preassembled fitting.
‘U’ Fittings B412
B107S
B596
THREE HOLE OFFSET U-SUPPORT
FIVE HOLE U-SUPPORT
THREE HOLE SWIVEL CLEVIS
• Material: 7 Gauge (4.5) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN, GRN • Wt./C 51 Lbs. (23.1 kg)
• Material: 7 Gauge (4.5) • Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN • Wt./C 89 Lbs. (40.3 kg)
57/16” (138.1)
33/4”
13/16”
(95.2)
(20.6)
3 1” 1 /8”
17/8”
(25.4)
(47.6)
(34.9)
21/4” (57.1)
7/16” (11.1) Dia. 4 Holes 9/16” (14.3) Dia.
13/4” (44.4)
15/8”
15/8”
(41.3)
(41.3)
B578
B594
B266
THREE HOLE LIGHT-WEIGHT U-SUPPORT
FIVE HOLE U-SUPPORT
SIX HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 106 Lbs. (48.1 kg)
• Standard finishes: ZN, GRN • Wt./C 105 Lbs. (47.6 kg)
• Material: 10 Gauge (3.4) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 18 Lbs. (8.1 kg)
17/8”
35/16”
121/32”
(84.1)
(42.1)
(47.6)
311/16” (93.6)
3/4” (19.0)
15/8” (41.3)
13/32” (10.3) 9/32” (7.1) Dia. 3 Holes
15/8” (41.3)
71/32”
35/16”
(178.6)
111/16”
71/16”
(42.8)
(84.1)
(179.4)
B425
B581
B519
SIX HOLE U-SUPPORT
EIGHT HOLE U-SUPPORT
EIGHT HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 167 Lbs. (75.7 kg)
• Standard finishes: ZN, GRN • Wt./C 201 Lbs. (91.2 kg)
• Standard finishes: ZN, GRN • Wt./C 266 Lbs. (102.5 kg)
111/16” Strut Fittings
(42.9)
31/2”
31/2”
(88.9)
(88.9)
15/8”
31/2”
(41.3)
(88.9)
31/2” (88.9)
15/8” (41.3)
57/16” (138.1)
71/16” (179.4)
513/32” (137.3)
Reference page 72 for general fitting and standard finish specifications.
88
Strut Systems
‘U’ Fittings B333
B451
SLOTTED THREE HOLE U-SUPPORT FOR B22
SLOTTED THREE HOLE U-SUPPORT WITH GUSSET FOR B22
A
• Standard finishes: ZN, GRN
• Consists of B333-1, 2, or 3 with gusset plate welded on back. • Material: ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN
C
9/16”
(14.3)
x 11/2”
A
Slots-(2)
(38.1) 9/16”
(14.3)
x 11/2”
Slots-(2)
(38.1)
15/8”
B
(41.3)
Part No.
Wt./C A
B333-1 B333-2 B333-3
(A)
B
(B)
C
71/2” (190.5) 15/16” (33.3) 81/2” (215.9) 115/16” (49.2) 103/8” (263.5) 27/8” (73.0)
(C)
Lbs.
27/8”
(73.0) 103 33/8” (85.7) 115 45/16” (109.5) 135
Part No.
kg
A
B451-1 B451-2 B451-3
(46.7) (52.1) (61.2)
B408
Wt./C (A)
1
7 /2” (190.5) 81/2” (215.9) 103/8” (263.5)
Lbs.
kg
137 156 172
(62.1) (70.7) (78.0)
B358
TWO HOLE BUS DUCT CLEVIS
TWO HOLE CLEVIS
1/2”
• Standard finishes: ZN, GRN
(12.7)
13/16”
• Standard finishes: ZN, GRN
(20.6) 9/16” (14.3) DIA. 2 HOLES
17/8” (47.6)
17/8” (47.6)
A
Part No.
A
Wt./C A
B408-1 B408-2 B408-3
(A)
Lbs.
213/32” (61.1) 58 325/32” (96.0) 76 43/4” (762.0) 88
kg (26.3)
13/16” (20.6)
(34.5) (39.9)
Part No.
A
Wt./C
B358-4 B358-5 B358-6 B358-7 B358-8
4” 5” 6” 7” 8”
(A)
Lbs.
89 93 (152.4) 106 (177.8) 118 (203.2) 132
kg
(101.6)
(40.3)
(127.0)
(42.2) (48.1)
13/16”
(53.5)
(20.6)
(59.9)
B173
B595
B405
FOUR HOLE CLEVIS
THREE HOLE CLEVIS
• Standard finishes: ZN, GRN • Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN, GRN • Wt./C 75 Lbs. (34.0 kg)
THREE HOLE SUSPENSION CLEVIS • Standard finishes: ZN, GRN • Wt./C 75 Lbs. (34.0 kg)
37/16”
17/8” (47.6)
129/32” 35/16” (84.1)
121/32” (42.0)
(48.4)
35/16”
121/32” (42.0)
(84.1)
17/8” (47.6)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
89
Strut Fittings
(87.3)
(47.6)
17/8”
‘U’ Fittings B398-1
B415
THREE HOLE CUP SUPPORT
TWO HOLE BUS DUCT CONNECTION
• Standard finishes: ZN, GRN • Wt./C 73 Lbs. (33.1 kg)
• Standard finishes: ZN, GRN • Wt./C 56 Lbs. (25.4 kg)
17/8” (47.6)
111/16” (42.9)
23/32” (53.2)
11/16” (27.0)
15/8” (41.3)
111/16”
325/32”
(42.9)
(96.0)
1/2” (12.7)
11/16” (27.0)
B400
B400-1
B400-2
THREE STUD RING CONNECTION
ONE STUD RING CONNECTION
ONE STUD RING CONNECTION
• 1/2”-13 stud protrudes 1”
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 53 Lbs. (24.0 kg)
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 40 Lbs. (18.1 kg)
(25.4mm)
• Standard finishes: ZN • Wt./C 85 Lbs. (38.5 kg)
111/16” 23/16”
(42.9)
111/16” 111/16”
(42.9)
(47.6)
(47.6)
(42.9)
(55.6)
17/8” 17/8”
B400-3
B400-4
B536
TWO STUD RING CONNECTION
TWO STUD RING CONNECTION
TAPPED U-SUPPORT
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 59 Lbs. (26.7 kg)
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 59 Lbs. (26.7 kg)
• Standard finishes: ZN • Wt./C 87 Lbs. (39.4 kg)
Strut Fittings
15/8” (41.3)
111/16” (42.9)
111/16” (42.9)
111/16” (42.9)
111/16” (42.9)
59/16” (141.3) Tapped 5/16”-18 (2) Holes
Reference page 72 for general fitting and standard finish specifications.
90
Strut Systems
‘Z’ Fittings B526
B106-52
B106-42
TWO HOLE OFFSET Z-SUPPORT
TWO HOLE Z-SUPPORT FOR B52
TWO HOLE Z-SUPPORT FOR B42
• Standard finishes: ZN, GRN • Wt./C 38 Lbs. (17.2 kg)
• Standard finishes: ZN, GRN • Wt./C 40 Lbs. (18.1 kg)
• Standard finishes: ZN, GRN • Wt./C 44 Lbs. (20.0 kg)
1/4” (6.3)
315/32”
13/16”
1”
(20.6)
(25.4)
(88.1)
15/8”
31/2”
31/2”
(88.9)
(88.9)
(41.3)
B106-32
B106-12
B105
TWO HOLE Z-SUPPORT FOR B32
TWO HOLE Z-SUPPORT FOR B12
THREE HOLE Z-SUPPORT FOR B22
• Standard finishes: ZN, GRN • Wt./C 51 Lbs. (23.1 kg)
• Standard finishes: ZN, GRN • Wt./C 63 Lbs. (28.6 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 51 Lbs. (23.1 kg)
15/8” (41.3)
27/16”
13/8”
(61.9)
(34.9)
31/2”
31/2”
31/2”
(88.9)
(88.9)
(88.9)
B110
B586
B108
THREE HOLE Z-SUPPORT FOR B11
TWO HOLE Z-SUPPORT
TWO HOLE OFFSET Z-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN • Wt./C 90 Lbs. (40.8 kg)
• Standard finishes: ZN, GRN • Wt./C 55 Lbs. (24.9 kg)
31/2” (88.9)
31/2”
31/2” (88.9)
Strut Fittings
(88.9)
21/8”
47/8”
15/8”
(123.8)
(54.0)
(41.3)
31/2” (88.9)
15/8” (41.3)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
91
‘Z’ Fittings B387
B407
TWO HOLE Z-BUS DUCT CONNECTION
TWO HOLE Z-SUPPORT
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
15/8”
31/2”
(41.3)
(88.9)
15/8”
31/2”
(41.3)
(88.9) 1/2” (12.7)
Part No. B387 B387-1 B387-2
A
(A)
Lbs.
43/4” (120.6) 325/32” (96.0) 213/32” (61.1)
kg
89 (40.3) 78 (35.4) 62 (28.1)
Wt./C Part No.
A
B407-4 4” B407-5 5” B407-6 6” B407-7 7” B407-8 8” B407-95/8 95/8”
Wt./C
A
A
(A)
Lbs.
kg
(101.6)
77 95 98 105 120 138
(34.9)
(127.0) (152.4) (177.8) (203.2) (244.5)
(43.1) (44.4) (47.6) (54.4) (62.6)
B534
B535
B111
TAPPED Z-SUPPORT
TAPPED Z-SUPPORT
• Standard finishes: ZN • Wt./C 51 Lbs. (23.1 kg)
• Standard finishes: ZN • Wt./C 50 Lbs. (22.7 kg)
THREE HOLE SHEATH CORNER CONNECTION
15/8”
15/8”
15/8”
(41.3)
• Standard finishes: ZN, GRN • Wt./C 68 Lbs. (30.8 kg)
31/2”
15/8”
(41.3)
(88.9)
(41.3)
(41.3)
31/2” (88.9)
15/8” 15/8”
15/8”
(41.3)
(41.3)
(41.3)
5/16”-18 Tapped Holes (2)
5/16”-18
Tapped Hole
15/8”
Strut Fittings
(41.3)
B538
B539
TAPPED CORNER CONNECTION
TAPPED CORNER CONNECTION
• Standard finishes: ZN • Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN • Wt./C 68 Lbs. (30.8 kg)
15/8” (41.3)
17/8” (47.6)
5/16”-18 Tapped Holes (4)
15/8” (41.3)
17/8” (47.6)
31/2” (88.9)
31/2” (88.9)
5/16”-18 Tapped Holes (2)
Reference page 72 for general fitting and standard finish specifications.
92
Strut Systems
‘Z’ Fittings B410-52
B410-32
B410-22
CHANNEL HANGER BRACKET FOR B52
CHANNEL HANGER BRACKET FOR B32
CHANNEL HANGER BRACKET FOR B22
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 6.7 Lbs. (3.0 kg)
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 8.3 Lbs. (3.7 kg)
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 9 Lbs. (4.1 kg)
13/16”
9/32” (7.1)
13/16”
13/16”
(20.6)
(20.6)
(20.6)
Dia. Hole
9/32” (7.1) Dia. Hole
9/32” (7.1) Dia. Hole
13/16” (20.6)
13/8”
15/8”
(34.9)
(41.3)
B410-12
B410-11
B580
CHANNEL HANGER BRACKET FOR B12
CHANNEL HANGER BRACKET FOR B11
FIVE HOLE GUSSETTED Z-SUPPORT
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 11.2 Lbs. (5.1 kg)
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 13.4 Lbs. (6.1 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
9/32” (7.1)
(88.9)
(20.6)
(20.6)
Dia. Hole
31/2”
13/16”
13/16”
31/2” (88.9)
9/32” (7.1) Dia. Hole
31/4”
27/16”
(82.5)
(61.9)
15/8” (41.3)
B515
B428
ADJUSTABLE OFFSET GUSSETTED Z-SUPPORT
EIGHT HOLE GUSSETTED CORNER CONNECTION
• Standard finishes: ZN, GRN • Wt./C 93 Lbs. (42.2 kg)
• Standard finishes: ZN, GRN • Wt./C 203 Lbs. (92.1 kg)
15/32”
31/2”
53/4” (146.0)
(47.6)
(88.9)
37/8” (98.4)
9/16”
x 29/16”
(14.3)
(65.1)
Slots
Strut Fittings
(11.9)
53/4” (146.0)
17/8”
17/8” (47.6)
31/2” (88.9)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
93
Wing Fittings B267R
B267L
B270R
THREE HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
THREE HOLE SINGLE CORNER CONNECTION (LEFT HAND)
FOUR HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN • Wt./C 77 Lbs. (34.9 kg)
111/16” 21/16”
21/16”
(52.4)
(52.4)
(42.8)
21/16” (52.4)
15/8”
15/8”
(41.3)
(41.3)
31/2” (88.9)
31/2”
313/16”
(88.9)
(96.8)
B270L
B268R
B268L
FOUR HOLE SINGLE CORNER CONNECTION (LEFT HAND)
FIVE HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
FIVE HOLE SINGLE CORNER CONNECTION (LEFT HAND)
• Standard finishes: ZN, GRN • Wt./C 77 Lbs. (34.9 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
111/16” (42.8)
21/16”
315/16” (100.0) 5 1 /8”
(52.4)
315/16” (100.0)
(41.3)
313/16”
15/8” (41.3)
31/2”
(96.8)
31/2”
(88.9)
(88.9)
B269R
B269L
B119
SIX HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
SIX HOLE SINGLE CORNER CONNECTION (LEFT HAND)
FOUR HOLE DOUBLE CORNER CONNECTION
• Standard finishes: ZN, GRN • Wt./C 120 Lbs. (54.4 kg)
• Standard finishes: ZN, GRN • Wt./C 120 Lbs. (54.4 kg)
• Standard finishes: ZN, GRN • Wt./C 71 Lbs. (32.2 kg)
31/2”
(88.9)
(88.9)
Strut Fittings
31/2”
315/16”
315/16”
(100.0)
(100.0)
21/16”
15/8”
(52.4)
(41.3)
53/8” (136.5)
53/8”
31/2” (88.9)
(136.5)
Reference page 72 for general fitting and standard finish specifications.
94
Strut Systems
Wing Fittings B120
B121
B271
SIX HOLE DOUBLE CORNER CONNECTION
EIGHT HOLE DOUBLE CORNER CONNECTION
FIVE HOLE DOUBLE WING CONNECTION
• Standard finishes: ZN, GRN • Wt./C 110 Lbs. (49.9 kg)
• Standard finishes: ZN, GRN • Wt./C 152 Lbs. (68.9 kg)
• Standard finishes: ZN, GRN • Wt./C 95 Lbs. (43.1 kg)
57/16” (138.1)
31/2”
15/8”
315/16”
(41.3)
(88.9)
315/16”
21/16”
(100.0)
(52.4)
(100.0)
15/8” (41.3)
31/2”
53/8”
(88.9)
(136.5)
111/16” (42.8)
B272
B273
B122
EIGHT HOLE DOUBLE WING CONNECTION
TEN HOLE DOUBLE WING CONNECTION
SIX HOLE TRIPLE WING CONNECTION
• Standard finishes: ZN, GRN • Wt./C 156 Lbs. (70.7 kg)
• Standard finishes: ZN, GRN • Wt./C 185 Lbs. (83.9 kg)
• Standard finishes: ZN, GRN • Wt./C 110 Lbs. (49.9 kg)
57/16”
93/16”
(138.1)
(233.4)
57/16” (138.1)
315/16” 315/16”
(100.0)
15/8”
31/2”
21/16”
(100.0)
(52.4)
(88.9)
15/8” 111/16”
111/16”
111/16”
(42.8)
(42.8)
(42.8)
(41.3)
B123
B124
B276
TWELVE HOLE TRIPLE WING CONNECTION
NINE HOLE TRIPLE WING CONNECTION
FOURTEEN HOLE DOUBLE CORNER GUSSETTED CONNECTION
• Standard finishes: ZN, GRN • Wt./C 234 Lbs. (106.1 kg)
• Standard finishes: ZN, GRN • Wt./C 177 Lbs. (80.3 kg)
• Standard finishes: ZN, GRN • Wt./C 196 Lbs. (88.9 kg)
57/16”
93/16”
(138.1)
(233.4)
31/2” (88.9)
315/16”
315/16”
(100.0)
15/8”
(100.0)
(41.3)
111/16” (42.8)
111/16”
4” (101.6)
(42.8)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
95
Strut Fittings
4” (101.6)
Wing Fittings B274R
B274L
B495
EIGHT HOLE SINGLE CORNER GUSSETTED CONNECTION (RIGHT HAND)
EIGHT HOLE SINGLE CORNER GUSSETTED CONNECTION (LEFT HAND)
TEN HOLE DOUBLE WING GUSSETTED CONNECTION
• Standard finishes: ZN, GRN • Wt./C 176 Lbs. (79.8 kg)
• Standard finishes: ZN, GRN • Wt./C 176 Lbs. (79.8 kg)
• Standard finishes: ZN, GRN • Wt./C 240 Lbs. (108.8 kg)
93/16”
511/16”
521/32”
(144.5)
(233.4)
(143.7)
315/16” (100.0)
31/2”
37/8”
315/16” (100.0)
(88.9)
(88.9)
(88.9)
111/16”
111/16”
(42.8)
(42.8)
(98.4)
31/2”
31/2”
111/16” (42.8)
B277
B362
B571
TWELVE HOLE TRIPLE WING GUSSETTED CONNECTION
EIGHT HOLE DOUBLE CORNER GUSSETTED CONNECTION
EIGHT HOLE WING CONNECTION
• Standard finishes: ZN, GRN • Wt./C 285 Lbs. (129.3 kg)
• Standard finishes: ZN, GRN • Wt./C 226 Lbs. (102.5 kg)
• Standard finishes: ZN, GRN • Wt./C 201 Lbs. (91.2 kg)
93/16” (233.4)
53/8” (136.5) 4” (101.6)
315/16” 31/2”
315/16”
(100.0)
(100.0)
31/2”
(88.9)
(88.9)
15/8”
111/16”
(41.3)
(42.8)
4” (101.6)
B346R
EIGHT HOLE DOUBLE CORNER GUSSETTED CONNECTION (LEFT HAND)
EIGHT HOLE DOUBLE CORNER GUSSETTED CONNECTION (RIGHT HAND)
• Standard finishes: ZN, GRN • Wt./C 242 Lbs. (109.8 kg)
• Standard finishes: ZN, GRN • Wt./C 242 Lbs. (109.8 kg)
Strut Fittings
B346L
53/8” (136.5)
31/2”
31/2”
53/8” (136.5)
(88.9)
(88.9)
Reference page 72 for general fitting and standard finish specifications.
96
Strut Systems
Post Bases B279
B279SQ
B279FL
POST BASE FOR B22
POST BASE FOR B22
POST BASE FOR B22
• Standard finishes: ZN, GRN • Wt./C 314 Lbs. (142.4 kg)
• Standard finishes: ZN, GRN • Wt./C 314 Lbs. (142.4 kg)
• Standard finishes: ZN, GRN • Wt./C 230 Lbs. (104.3 kg) 3/4” (19.0) Dia .2 Holes
111/16” (42.8)
3/4” (19.0) Dia .4 Holes
111/16” (42.8)
6”
111/16”
3/4” (19.0) Dia .4 Holes
(42.8)
15/8”
15/8”
(41.3)
15/8”
(41.3)
(152.4)
41/4” 6”
41/4” (107.9)
(107.9)
(152.4)
6”
61/4”
8” (203.2)
(158.7)
3”
6”
(152.4)
(76.2)
(152.4)
3”
(41.3)
(76.2)
B280
B280SQ
POST BASE FOR B22
POST BASE FOR B22
B280FL POST BASE FOR B22
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 392 Lbs. (177.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 392 Lbs. (177.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 312 Lbs. (141.5 kg)
111/16” 3/4” (19.0) Dia .4 Holes
(42.8)
3/4” (19.0) Dia .2 Holes
3/4” (19.0) Dia .4 Holes
31/2”
(42.8)
31/2”
(88.9)
6”
111/16”
(42.8)
111/16”
(88.9)
31/2”
(152.4)
61/4”
41/4” 6”
6”
(107.9)
(107.9)
(152.4)
(152.4)
8”
41/4”
3”
(88.9)
(158.7)
(203.2)
6”
3”
(152.4)
(76.2)
(76.2)
B281A
B281ASQ
B281AFL
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
• Standard finishes: ZN, GRN • Wt./C 330 Lbs. (149.7 kg)
• Standard finishes: ZN, GRN • Wt./C 330 Lbs. (149.7 kg)
• Standard finishes: ZN, GRN • Wt./C 250 Lbs. (113.4 kg)
3/4” (19.0) Dia .4 Holes
35/16” 35/16”
(41.3)
(84.1)
3/4” (19.0) Dia .4 Holes
35/16” (84.1)
15/8” (41.3)
6” 41/4”
(152.4)
6”
(107.9)
41/4” (107.9)
(152.4)
8” 6”
(41.3)
(203.2)
3” (76.2)
3” (76.2)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
15/8”
(158.7)
(152.4)
6” (152.4)
61/4”
97
Strut Fittings
15/8”
3/4” (19.0) Dia .2 Holes
Post Bases B281
B281SQ
B281FL
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
• Standard finishes: ZN, GRN, HDG • Wt./C 400 Lbs. (181.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 400 Lbs. (181.4 kg)
• Standard finishes: ZN, GRN • Wt./C 320 Lbs. (145.1 kg)
3/4” (19.0)
35/16”
Dia. 4 Holes
35/16” 31/2”
(84.1)
(88.9)
(84.1) 3/4” (19.0)
3/4” (19.0)
Dia. 4 Holes
Dia. 2 Holes
35/16” (84.1)
31/2” (88.9)
6”
31/2”
(152.4)
6” (152.4)
41/4” 41/4”
(107.9)
8”
(107.9)
6”
6”
(88.9)
61/4” (158.7)
(203.2)
(152.4)
(152.4)
3”
3”
(76.2)
(76.2)
B281M
B281MSQ
B570
POST BASE FOR B22-2PL
POST BASE FOR B22-2PL
• Standard finishes: ZN, GRN • Wt./C 470 Lbs. (213.2 kg)
• Standard finishes: ZN, GRN • Wt./C 470 Lbs. (213.2 kg)
POST BASE FOR FOUR CHANNEL COMBINATIONS • Standard finishes: ZN, GRN • Wt./C 397 Lbs. (180.1 kg)
39/16” (90.5) 3/4” (19.0)
111/16”
Dia. 4 Holes
(42.8) 3/4” (19.0)
(41.3)
(88.9)
Dia. 4 Holes
31/2”
315/32”
(88.9)
6”
(87.9)
6”
6”
(152.4)
(152.4)
1/4”
6”
(6.3)
41/4” (107.9)
41/4” (107.9) 6” (152.4)
3”
(152.4)
(152.4)
6”
3”
(152.4)
3/4” (19.0)
(76.2)
Dia. 4 Holes
(76.2)
B570A
B278
POST BASE FOR FOUR POST BASE FOR B22 CHANNEL COMBINATIONS • Standard finishes: ZN, GRN • Standard finishes: ZN, GRN • Wt./C 550 Lbs. (249.5 kg)
Strut Fittings
15/8”
31/2”
31/2” (88.9)
• Wt./C 288 Lbs. (130.6 kg)
7/16”
(11.1) Dia. 4 Holes
B300
B585 POST BASE FOR B22A
POST BASE
• Standard finishes: ZN, GRN • Wt./C 97 Lbs. (44.0 kg)
• Material: Malleable Iron • Standard finishes: ZN, GRN • Wt./C 259 Lbs. (117.5 kg)
4”
15/8”
(101.6)
(41.3)
13/4”
31/2”
1/4”
3/4” (19.0)
(44.4)
(88.9)
(6.3)
(76.2)
(152.4)
5” (127.0)
6” 3”
3/4” (19.0)
Dia. 4 Holes
Countersunk To 3/4” (19.0) Dia. 9/16”
6” (152.4)
3/8” (9.5)
5”
15/8”
(127.0)
(41.3)
31/2”
31/16” (77.8)
7” (177.8)
(14.4)
21/16” (52.4)
(88.9)
Reference page 72 for general fitting and standard finish specifications.
98
Strut Systems
Brackets B187 BRACKET
B188 BRACKET
• Uniform Loading 1450 Lbs. (6.45 kN) • Safety Factor of 2.5 • Hole Spacing on Bracket Top 55/16” (150.8) Center to Center • Standard finishes: ZN, GRN • Wt./C 193 Lbs. (87.5 kg)
• Uniform Loading 1080 Lbs. (4.80 kN) • Safety Factor of 2.5 • Hole Spacing on Bracket Top 815/16” (227.0) Center to Center • Standard finishes: ZN, GRN • Wt./C 241 Lbs. (109.3 kg)
21/4”
11/16”
11/16”
(57.1)
(27.0)
21/4”
(27.0)
(57.1)
4”
9”
(101.6)
(228.6)
4” (101.6)
12” (304.8)
B189 BRACKET
B541 BRACKET
• Uniform Loading 870 Lbs. (3.87 kN) • Safety Factor of 2.5 • Hole Spacing on Bracket Top 1115/16” (303.2) Center to Center • Standard finishes: ZN, GRN • Wt./C 308 Lbs. (139.7 kg)
• • • • •
11/16” (27.0)
Uniform Loading 1240 Lbs. (5.51 kN) Safety Factor of 2.5 Hole Spacing on Bracket Top 77/16” (188.9) Center to Center Standard finishes: ZN, GRN Wt./C 201 Lbs. (91.2 kg)
21/4”
11/16”
21/4”
(57.1)
(27.0)
(57.1)
4”
4”
(101.6)
(101.6)
15”
101/2” (266.7)
(381.0)
B190 12” (304.8) BRACKET
B191-18 18” (457.2) BRACKET
• • • •
• • • •
Uniform Loading 900 Lbs. (4.00 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 260 Lbs. (117.9 kg)
11/16”
11/16” (27.0)
(101.6)
(27.0) 9/16”
x 3”
Slot (14.3) (76.2)
4” (101.6)
12”
18”
(304.8)
(457.2)
71/2” (190.5)
71/2” (190.5)
2”
9/16”
x 3” Slot (14.3) (76.2)
(50.8)
2” (50.8)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
99
Strut Fittings
4”
Uniform Loading 600 Lbs. (2.67 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 377 Lbs. (171.0 kg)
Brackets B191-24 24” (609.6) BRACKET • • • •
11/16” (27.0)
B192 24” (609.6) BRACKET
11/16”
Uniform Loading 450 Lbs. (2.00 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 377 Lbs. (171.0 kg)
• • • •
(27.0)
Uniform Loading 820 Lbs. (3.65 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 576 Lbs. (261.3 kg)
4” (101.6)
6” (152.4)
24”
24”
(609.6)
(609.6)
12” 27/16”
71/2”
(61.9)
(190.5) 9/16”
(304.8) 9/16”
x 3” Slot (14.3) (76.2)
x 3”
Slot (14.3) (76.2)
2”
2”
(50.8)
(50.8)
B290 161/2” (419.1) BRACKET
B289-12 121/2” (317.5) BRACKET
• • • •
• • • •
Uniform Loading 1200 Lbs. (5.34 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 405 Lbs. (183.7 kg)
Uniform Loading 1040 Lbs. (4.63 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 285 Lbs. (129.3 kg)
13/16”
13/16”
13/16”
(30.1)
(30.1)
(30.1)
13/16” (30.1)
6”
51/4”
(152.4)
(133.3)
6”
161/2”
31/8”
(152.4)
31/4”
121/2”
(82.5)
(317.5)
(419.1)
31/8” (79.4)
33/4”
(79.4)
(95.2)
53/4” (146.0)
21/2”
13/16”
21/2”
(63.5)
(30.1)
(63.5)
13/16” (30.1)
B289-14 141/2” (368.3) BRACKET
B291 181/2” (469.9) BRACKET
• • • •
• • • •
Uniform Loading 900 Lbs. (4.00 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 295 Lbs. (133.8 kg)
13/16”
13/16” (30.1)
Uniform Loading 1070 Lbs. (4.76 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 468 Lbs. (212.3 kg) (30.1)
13/16”
(30.1)
Strut Fittings
(30.1)
31/4” 6” (152.4)
13/16”
(82.5)
31/8” (79.4)
141/2”
6”
51/4”
(152.4)
(133.3)
(368.3)
31/8” 181/2” (79.4)
53/4”
73/4” (196.8)
(146.0)
21/2” (63.5)
(469.9)
21/2” (63.5)
13/16” (30.1)
13/16” (30.1)
Reference page 72 for general fitting and standard finish specifications.
100
Strut Systems
Brackets 13/16”
B292 201/2” (520.7) BRACKET
B297
• • • •
DOUBLE CHANNEL BRACKET
Uniform Loading 600 Lbs. (2.67 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN, HDG, SS4 Wt./C 490 Lbs. (222.2 kg) (30.1)
61/4” (158.7)
• Safety Factor of 2.5 • Standard finishes: ZN, GRN, HDG
13/16”
2” (50.8) 3/8”
(20.6)
(9.5)
A
13/16” (30.1)
6”
45/8” (117.5)
71/4” (184.1)
(152.4)
31/8” (79.4)
201/2”
Part No. B297-12 B297-18 B297-24 B297-30 B297-36 B297-42
(520.7)
73/4” (196.8)
21/2” (63.5)
13/16” (30.1)
B409 SINGLE CHANNEL BRACKET
13/16”
• Safety Factor of 2.5 • Standard finishes: ZN, GRN, SS4
Uniform Load A 12” 18” 24” 30” 36” 42”
(304.8) (457.2) (609.6) (762.0) (914.4) (1066.8)
13/16”
(20.6)
kN
Lbs.
kg
1660 1100 835 665 550 465
(7.37) (4.88) (3.71) (2.95) (2.44) (2.06)
485 668 857 1040 1240 1440
(220.0) (303.0) (388.7) (471.7) (562.4) (653.2)
11/2”
B494
(38.1)
BRACED SINGLE BRACKET
H 2”
15/8”
(50.8)
Wt./C
Lbs.
(20.6)
45/8” (117.5)
B22A
L
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
(41.3)
4”
A
(101.6) Inside Brace on B494-24 and Larger.
3” B22
(76.2)
Part No. B409-6 B409-9 B409-12 B409-14 B409-16 B409-18 B409-24
Uniform Load A 6” 9” 12” 14” 16” 18” 24”
Lbs.
1920 1280 960 800
(152.4) (228.6) (304.8) (355.6) (406.4) (457.2) (609.6)
730
640 480
kN (8.54) (5.69) (4.27) (3.56) (3.25) (2.84) (2.13)
152 195 232 274 314
347 450
B174SH-B186SH L&R SLOTTED BRACKET • • • •
Safety Factor of 2.5 Specify L for left or R for right bracing Material: ASTM A1011 33,000 PSI min. yield Standard finishes: ZN, GRN
2” (50.8)
A B 2”
1”
(50.8)
(25.4)
Mounting Hole 7/16” (11.1) Dia.
13/32” x 1” Slot (10.3) (25.4)
kg (68.9) (88.4) (105.2) (124.3) (142.4) (157.4) (204.1)
Part No. B174SH B175SH B176SH B177SH B178SH B179SH B180SH B181SH B182SH B183SH B184SH B185SH B186SH
Uniform Load L
H
12” (304.8) 18” (475.2) 24” (609.6) 30” (762.0) 36” (914.4) 42” (1066.8) 48” (1219.2)
83/4” 83/4” 83/4” 111/4” 111/4” 16” 16”
Lbs.
(222.2) 1580 (222.2) 1000 (222.2) 996 (285.7) 924 (285.7) 864 (406.4) 580 (406.4) 500
24” 26” 28” 30” 12” 14” 16” 18” 20” 22” 6” 8” 10”
(609.6) (660.4) (711.2) (762.0) (304.8) (355.6) (406.4) (457.2) (508.0) (558.8) (152.4) (203.2) (254.0)
B 67/16” 615/16” 77/16” 715/16” 37/16” 315/16” 47/16” 415/16” 57/16” 515/16” 115/16” 27/16” 215/16”
(163.5) (176.2) (188.9) (201.6) (87.3) (100.0) (112.7) (125.4) (138.1) (150.8) (49.2) (61.9) (74.6)
kg (165.1) (217.3) (324.8) (420.5) (496.7) (635.0) (684.9)
Wt./C
Lbs.
kN
Lbs.
kg
225 225 225 225 350 350 250 250 250 250 225 225 325
(1.00) (1.00) (1.00) (1.00) (1.55) (1.55) (1.11) (1.11) (1.11) (1.11) (1.00) (1.00) (1.44)
370 425 480 520 143 162 204 232 275 317 58 82 103
(167.8) (192.8) (217.7) (235.9) (64.8) (73.5) (92.5) (105.2) (124.7) (143.8) (26.3) (37.2) (46.7)
Right bracket shown, left bracket gussett on opposite side.
101
Wt. /C Lbs.
(7.02) 364 (4.45) 479 (4.43) 716 (4.11) 927 (3.84) 1095 (2.58) 1400 (2.22) 1510
Uniform Load A
Reference page 72 for general fitting and standard finish specifications. Strut Systems
kN
Strut Fittings
9/32” (7.1) Dia. Holes
Part No. B494-12 B494-18 B494-24 B494-30 B494-36 B494-42 B494-48
Wt./C Lbs.
B42
Brackets B196
B198
13/16”
CHANNEL CLEVIS BRACKET
CHANNEL CLEVIS BRACKET
(20.6)
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
• Safety Factor of 2.5 53/8” • Standard finishes: (136.5) ZN, GRN
13/16” (20.6)
31/2” (88.9)
A 35/8”
A
(92.1)
B22 Uniform Load
B22
Part No.
A
(A)
Lbs.
kN
Lbs.
kg
B196-18 B196-24
18” 24”
(457.2)
600 450
(2.67)
430 510
(195.0)
(609.6)
(2.00)
Wt./C
(231.3)
Part No.
A
(A)
Uniform Load Lbs.
kN
Lbs.
kg
B198-6 B198-12
6” 12”
(152.4)
1600 800
(7.12)
185 284
(128.8)
(304.8)
B293
CHANNEL CLEVIS BRACKET
CHANNEL BRACKET
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
(20.6)
(83.9)
13/16”
B198A 13/16”
(3.56)
Wt./C
(20.6)
31/2”
11/2”
(88.9)
(38.1)
31/2”
A
(88.9)
A B22 B22 Part No.
Uniform Load A
B198A-6 6” B198A-12 12”
Wt./C
(A)
Lbs.
kN
Lbs.
kg
(152.4)
1600 800
(7.12)
185 284
(83.9)
(304.8)
B293A CHANNEL BRACKET • Safety Factor of 2.5 • Standard finishes: ZN, GRN
(3.56)
(128.8)
(20.6)
11/2”
31/2”
(38.1)
Strut Fittings
A
Uniform Load
B293A-6 6” B293A-12 12” B293A-18 18” B293A-24 24”
kN
Lbs.
(152.4)
1200 600 400 300
(5.34)
144 252 340 412
(609.6)
Lbs.
kN
Lbs.
B293-6 B293-12 B293-18 B293-24
6” 12” 18” 24”
(152.4)
1200 600 400 300
(5.34)
144 252 340 412
(304.8) (457.2) (609.6)
(2.67) (1.78) (1.33)
Wt./C kg (65.3) (114.3) (154.2) (186.9)
(2.67) (1.78) (1.33)
B22
Wt./C
Lbs.
(457.2)
Uniform Load
63/8” (161.9)
(A) (304.8)
(A)
• Safety Factor of 2.5 • 6300 In.-Lbs (712 N•m) applies to fitting only, not to strength of strut arm • Refer to page 223 for strut 13/32” loading data (27.8) • Standard finishes: ZN, GRN • Wt./C 210 Lbs. (95.2 kg)
B22
A
A
B194 BRACKET FOR B22 & B24
13/16”
(88.9)
Part No.
Part No.
kg (65.3)
23/16”
(114.3)
(55.6)
(154.2)
B22
33/4”
(186.9)
(95.3)
Reference page 72 for general fitting and standard finish specifications.
102
Strut Systems
Brackets B370
B195
BRACKET FOR B22A & B11
• Safety Factor of 2.5 13/32” • 13000 In.-Lbs (1469 N•m) applies (27.8) to fitting only, not to strength of strut arm • Refer to page 217 for strut loading data • Standard finishes: ZN, GRN • Wt./C 266 Lbs. (120.6 kg) 8”
B22
BRACKET FOR B42
• Safety Factor of 2.5 • 2500 In.-Lbs (282 N•m) applies to fitting only, not to strength of strut arm 21/8” • Refer to page 217 for strut (54.0) loading data • Standard finishes: ZN, GRN • Wt./C 174 Lbs. (78.9 kg)
B22
37/8”
(203.2)
(98.4)
315/16” (100.0)
B22A
B42
33/4”
33/4”
(95.2)
(95.2)
B440
B449-4, 8 & 12
BRACKET FOR B52 & B54
CABLE SADDLE BRACKET
• Safety Factor of 2.5 • 2000 In.-Lbs (226 N•m) applies to fitting only, not to strength of strut arm • Refer to page 217 for strut loading data • Standard finishes: ZN, GRN B22 21/8” • Wt./C 177 Lbs. (80.3 kg)
13/16” (20.6)
• Safety Factor of 2.5 • Material: 11 Gauge (3.0) B ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN
(54.0)
A
37/8” (98.4)
2” (50.8)
B52
Part Uniform Load Wt./C Lbs. kN Lbs. kg No. A B 1 3 B449-4 4 /2” (114.3) 2 /8” (60.3) 2400 (10.67) 74 (33.5) B449-8 81/2” (215.9) 23/8” (60.3) 1270 (5.65) 124 (56.2) B449-12 121/2” (317.5) 4” (101.6) 860 (3.82) 184 (83.4)
33/4” (95.2)
B449-18 18” (457.2) CABLE SADDLE BRACKET • • • • •
Safety Factor of 2.5 Uniform Load 960 Lbs. (4.17 kN) Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 Standard finishes: ZN, GRN Wt./C 312 Lbs. (141.5 kg)
B293PL BRACKET PLATE ONLY • Standard finishes: ZN, GRN • Wt./C 46 Lbs. (20.8 kg)
13/16”
2” (50.8)
11/2”
4”
(38.1)
(101.6)
31/2” 18”
120°
(88.9)
13/16”
(457.2)
(20.6)
11/4” (31.7)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
103
Strut Fittings
(20.6)
Brackets B816
B852S-W-D
• Standard finishes: ZN, HDG
• Specify W = 8, 12, 16 • Specify D = 6, 8, 10, 12, 16, 18, 24 • 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band • Standard finishes: ZN, HDG
2”
13/32” (10.3) Dia.
(50.8)
61/2” (165.1)
13/16” (20.6) Dia.
23/8” (60.3)
21/8” (54.0) 9/16” (355.6)
(355.6)
725/32”
(14.3)
14” 14”
(197.6)
9/16” x 29/16” Slot
(14.3)
(65.1)
W D
11/16” x 1” Slot (17.4) (25.4)
13/16” x 1” Slot (20.6) (25.4)
B802D-W
B810-W
• Specify W = 8, 12, 16 • Standard finishes: ZN, HDG
• Specify W = 8, 12, 16 • 13/16” (20.6mm) x 1” (25.6mm) banding slots for steel band • Standard finishes: ZN, HDG
13/16” (20.6) Dia.
13/32” (10.3) Dia.
Strut Fittings
13/16” (20.6) Dia.
95/8” (244.5) W
725/32” (197.6)
W
13/16” x 1” Slot (20.6) (25.4)
Reference page 72 for general fitting and standard finish specifications.
104
Strut Systems
Brackets B811-W
B812-*
• Can be attached directly to B809 & B812 • Specify W = 8, 12, 16 • Standard finishes: ZN, HDG
• Specify D = 6, 8, 10, 12, 16, 18, 24 • 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band • Standard finishes: ZN, HDG
121/32” (42.1) 13/32” (10.3) Dia. 13/16” (20.6) Dia.
W
27/16”
725/32”
(61.9)
(197.6) 13/16” x 1” Slot (20.6) (25.4)
D 13/16” (20.6)
B809B-* • Specify D = 6, 8, 10, 12, 16, 18, 24 • 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band • Standard finishes: ZN, HDG
13/32” (10.3) Dia. 13/16” (20.6) Dia.
D
Part No.
D
H
725/32”
mm
In.
mm
B809B-6
6”
(152.4)
123/4”
(323.9)
B809B-8
8”
(203.2)
143/4”
(374.7) (425.5)
B809B-10
10”
(254.0)
163/4”
B809B-12
12”
(304.8)
183/4”
(476.2) (577.8) (628.6)
B809B-16
16”
(406.4)
223/4”
B809B-18 B809B-24
18” 24”
(457.2)
243/4” 273/4”
(609.6)
(197.6) 13/16” x 1” Slot (20.6) (25.4)
H
(704.8)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
105
Strut Fittings
In.
Miscellaneous Fittings B214 R&L
B514 R&L
REEL RACK SUPPORT FOR 11/4” (32) PIPE
REEL RACK SUPPORT FOR 2” (50) PIPE • Standard finishes: ZN, GRN • Wt./C 246 Lbs. (111.6 kg)
• Standard finishes: ZN, GRN • Wt./C 200 Lbs. (90.7 kg)
3”
3”
(76.2)
(76.2)
53/8” (136.5)
53/8” (136.5)
35/8”
(92.1)
(92.1)
53/8” (136.5)
A
B214R Right Hand
35/8”
B214L Left Hand
53/8” (136.5)
B514R Right Hand
B514L Left Hand
B475
B473
DOUBLE REEL RACK SUPPORT ON SINGLE CHANNEL FOR 11/4” (32) PIPE
DOUBLE REEL RACK SUPPORT ON SINGLE CHANNEL FOR 2” (50) PIPE
• Standard finishes: ZN, GRN • Wt./C 326 Lbs. (147.9 kg)
• Standard finishes: ZN, GRN • Wt./C 351 Lbs. (159.2 kg)
3”
3” (76.2)
(76.2)
9”
9”
(228.6)
(228.6)
B474
B472
DOUBLE REEL RACK CHANNEL FOR 11/4” (32) PIPE
DOUBLE REEL RACK SUPPORT ON DOUBLE CHANNEL FOR 2” (50) PIPE
• Standard finishes: ZN, GRN • Wt./C 257 Lbs. (116.6 kg)
• Standard finishes: ZN, GRN • Wt./C 299 Lbs. (135.6 kg)
31/4”
31/4”
(82.5)
Strut Fittings
(82.5)
53/8” (136.5)
53/8” (136.5)
Reference page 72 for general fitting and standard finish specifications.
106
Strut Systems
Miscellaneous Fittings B438
B439
PIPE SUPPORT BRACKET
PIPE SUPPORT BRACKET
• Standard finishes: ZN, GRN • Material: ASTM A36 • Wt./C 132 Lbs. (59.9 kg)
• Standard finishes: ZN, GRN • Wt./C 88 Lbs. (39.9 kg)
41/4” (107.9)
31/2” (88.9)
3/8”
4”
(9.5)
1/4”
4”
(101.6)
(6.3)
(101.6)
B411 SERIES
B381-B385
LADDER RUNGS
WALL LADDER BRACKETS
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
13/16” (20.6)
C
B 2”
A
I.D. (50.8)
13/16” (20.6)
A 13/16” (20.6)
Part No. B381 B382 B383 B384 B385
Wt./C Part No.
A
B411-12 12” B411-15 15” B411-18 18”
(A)
Lbs.
kg
(304.8)
176 202 234
(79.8)
(381.0) (457.2)
(91.6) (106.1)
Wt./C A 23/8” 43/8” 63/8” 83/8” 103/8”
(A) (60.3) (111.1) (161.9) (212.7) (263.5)
B 6” 8” 10” 12” 14”
(B) (152.4) (203.2) (254.0) (304.8) (355.6)
C 75/8” 95/8” 115/8” 135/8” 155/8”
(C) (193.7) (244.5) (295.3) (346.1) (396.9)
Lbs.
kg
110 (49.9) 164 (74.4) 200 (90.7) 253 (114.7) 318 (144.2)
B587-1/2, 3/4 & 1 PIPE COUPLING FITTING • Safety Factor of 2.5 • Standard finishes: ZN, GRN
Design Load
(68.2)
Part No. B587-1/2 B587-3/4 B587-1
For Pipe Size 1/2”
(15)
3/4”
(20)
1”
(25)
Strut Fittings
53/8” (136.5)
211/16”
Wt./C Lbs.
77 84 105
kg
Design Load Lbs.
kN
1000 (4.45) (38.1) 1400 (6.23) (47.6) 1900 (8.45) (34.9)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
107
Miscellaneous Fittings B349
B350
TROLLEY BEAM SUPPORT
TROLLEY BEAM JOINT SUPPORT
• Design Load 1200 Lbs. (5.34 kN) • Safety Factor of 2.5 • Use 3/8” x 3” bolts in side hole to clamp strut together (not included) • Standard finishes: ZN, GRN 9/16”(14.3) Dia. • Wt./C 107 Lbs. (48.5 kg)
• Design Load 1200 Lbs. (5.34 kN) • Use 3/8” x 3” bolts in side hole to clamp 21/8” (54.0) strut together (not included) • Standard finishes: ZN, GRN 9 /16”(14.3) Dia. • Wt./C 233 Lbs. (105.7 kg)
21/8” (54.0)
1 Hole
315/16”
1 Hole
(100.0)
7/16”(11.1) Dia. 6 Holes
11/32”
2 Holes
(26.2)
(26.2)
13/32”
15/8” (41.3)
121/32”
121/32” (42.0)
(42.0)
B614
COLUMN SUPPORT FOR B22 • Quick installation (one bolt to tighten) • Design Load 800 Lbs. (3.56 kN) Slip with Safety Factor of 3 • Use with B22 and B24 Channel • Sold in pairs • Standard finish: ZN • Wt./C 50 Lbs. (22.6 kg)
(100.0)
(88.9)
7/16”(11.1) Dia.
11/32”
315/16”
31/2”
21/32” (27.8) (16.7)
B613
B613A
COLUMN SUPPORT FOR B22
COLUMN SUPPORT FOR B52
• Design Load 800 Lbs. (3.56 kN) Slip with Safety Factor of 3 • Use with B22 and B24 Channel • Setscrews to be torqued to 19 ft./Lbs • Sold in pairs • Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Design Load 800 Lbs. (3.56 kN) Slip with Safety Factor of 3 • Use with B52 and B54 Channel • Setscrews to be torqued to 19 ft./Lbs • Sold in pairs • Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
15/8”
15/8”
(41.3)
(41.3)
31/2”
31/2”
(88.9) 3/8” x 2” Cone
3/8” x 2” Cone
Point Setscrews
Point Setscrews
B560
B562
45° STAIR SUPPORT
37-1/2° STAIR SUPPORT
• Standard finishes: ZN, GRN • Wt./C 220 Lbs. (99.8 kg)
• Standard finishes: ZN, GRN • Wt./C 206 Lbs. (93.4 kg)
87/8” (225.4)
87/8” (225.4)
Strut Fittings
(88.9)
31/2” 31/2”
(88.9)
11/16” 31/2”
17/8”
(88.9) 13/16”
31/2”
(27.0) 45°
13/16”
(47.6)
(88.9)
11/16” (27.0)
17/8”
(88.9) 371/2°
(47.6)
(20.6)
(20.6)
33/4”
33/4”
(95.2)
(95.2)
Reference page 72 for general fitting and standard finish specifications.
108
Strut Systems
Miscellaneous Fittings B376
35/16”
FOUR BEARING TROLLEY ASSEMBLY
B377
15/16”
(84.1)
TWO BEARING TROLLEY ASSEMBLY
(33.3)
• Safety Factor of 2.5 • Stainless steel ball bearings • Not for continuous cycling applications • Standard finishes: ZN 33/8” • Wt./C 110 Lbs. (49.9 kg) (85.7)
11/8” (28.6) Bearing O.D. 13/16” (20.6)
• Safety Factor of 2.5 • Stainless steel ball bearings • Not for continuous cycling applications • Standard finishes: ZN • Wt./C 48 Lbs. (21.8 kg)
15/16”
3”
(23.8)
(76.2)
Lbs.
kN
RPM
300 450 600
(1.33)
@600 @300 @100
Design Load
Lbs.
kN
RPM
150 225 437
(.67)
@600 @300 @100
(1.00) (1.94)
B477
33/8”
13/16”
(85.7)
(20.6)
11/4” (31.7)
Design Load
FOUR BEARING LIGHT DUTY TROLLEY ASSEMBLY
• • • • •
Design Load 50 Lbs. (.22 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN • Wt./C 30 Lbs. (13.6 kg)
11/4” (31.7)
11/8”
13/4”
(28.6)
(44.4)
B477P
• • • • •
Design Load 100 Lbs. (.44 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN • Wt./C 68 Lbs. (30.8 kg)
B478P
WITH PLASTIC BEARINGS
11/32”
• Design Load 10 Lbs. (.045 kN)
5/8” (15.9)
9/32” (7.1)
Dia. Hole (19.0)
(28.6) Bearing O.D.
B478
TWO BEARING LIGHT DUTY TROLLEY ASSEMBLY
3/4”
11/8”
Design Load in B22
Design Load in B22
(2.67)
(33.3)
5/8” (15.9)
(2.00)
15/16”
(8.7)
WITH PLASTIC BEARINGS • Design Load 20 Lbs. (.090 kN)
9/32”
x 9/16”
(7.1)
(14.3)
(31.7)
(7.1) Dia. Hole
Slot-(2) 3/4” (19.0)
11/4”
9/32”
3” (76.2)
2” (50.8)
Design Load
Design Load
B478H
B477H
FOUR BEARING LIGHT DUTY TROLLEY ASSEMBLY WITH EYE HOOK
TWO BEARING LIGHT DUTY TROLLEY ASSEMBLY WITH EYE HOOK • • • • •
11/4” (31.7)
• • • • •
Design Load 100 Lbs. (.44 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN 11/8” • Wt./C 72 Lbs. (32.6 kg) (28.6)
B477HP
WITH PLASTIC BEARINGS • Design Load 10 Lbs. (.045 kN)
3/4” I.D (19.0)
B478HP
WITH PLASTIC BEARINGS
315/16” (100.0)
11/32”
1/4” (6.3) EYE ROD
• Design Load 20 Lbs. (.090 kN)
(8.7)
3/4” I.D (19.0)
Design Load
Design Load
Reference page 72 for general fitting and standard finish specifications. Strut Systems
1/4” (6.3) EYE ROD
109
Strut Fittings
Design Load 50 Lbs. (.22 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN • Wt./C 36 Lbs. (16.3 kg)
Miscellaneous Fittings B203-B206 & B220-B223
B283-B286
CHANNEL END CAPS TYPE X
A
• Material: ASTM A1011 CS Type B • Standard finishes: ZN, GRN, HDG, SS4, AL
Part No. B203 B204 B205 B206 B220 B221 B222 B223
CHANNEL END CAPS • Material: ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN, GRN
A
Wt./C Use With
A
(A)
Lbs.
kg
B42 B54 B22 B32 B52 B12 B11 B24
1.015 .827 1.640 1.390 .827 2.452 3.265 1.640
(25.8) (21.0) (41.6) (35.3) (21.0) (62.3) (82.9) (41.6)
6 5 10 8 4 15 20 10
(2.7) (2.2) (4.5) (3.6) (1.8) (6.8) (9.1) (4.5)
B Part No.
Use With
A
Wt./C
B283 B284 B285 B286
B52 B54 & B56 B22 B24 & B26
119/32” 119/32” 119/32” 119/32”
(A)
B
(B)
(40.5) 25/32” (19.8) (40.5) 25/32” (19.8) (40.5) 119/32” (40.5) (40.5) 119/32” (40.5)
B287 & B288
B3322, B3332, B3342, B3352
CHANNEL END CAPS
ANCHOR END CAPS TYPE Y
• Material: ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN, GRN
• Material: ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN
Lbs.
kg
6 6 13 14
(2.7) (2.7) (5.9) (6.3)
3/8” (9.5)
119/32”
119/32”
(40.5)
(40.5)
Dia. Hole
25/8” (66.7)
A 113/16”
B
(46.0)
Part No.
Strut Fittings
B287 B288
Wt./C Use With
Lbs.
kg
B22 B24
13 14
(5.9) (6.3)
Part No.
Use With
A
Wt./C
B3322 B3332 B3342 B3352
B22I B32I B42I B52I
1.270 1.000 .645 .460
(A)
B
(32.2) 13/16” (25.4) 13/16” (16.4) 11/4” (11.7) 15/16”
(B)
Lbs.
kg
(30.2) (30.2) (31.8) (33.3)
15 15 15 15
(6.8) (6.8) (6.8) (6.8)
B822
B822A
B852
PLASTIC END CAP FOR B22 & B24
PLASTIC END CAP FOR B22A & B11
PLASTIC END CAP FOR B52
• Material: Soft White PVC • Wt./C 3 Lbs. (1.3 kg) • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
• Material: Soft White PVC • Wt./C 5 Lbs. (2.2 kg) • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
• Material: Soft White PVC • Wt./C 2.5 Lbs. (1.1 kg) • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
11/4” (31.7)
11/4”
11/4”
(31.7)
(31.7)
Reference page 72 for general fitting and standard finish specifications.
110
Strut Systems
Miscellaneous Fittings B823
B825
PROFILE END CAPS
PLASTIC END CAPS
• Material: PVC • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
• Material: Polyurethane • Available in colors: Gray (GRY), Green (GRN)
Approx. 3/4” deep (19.0)
Part No.
Fits Channel Sizes
Wt./C
B823-22A B22A, B24A, B26A B823-22 B22, B24, B26 B823-42 B42 B823-52 B52, B54, B56
Lbs.
kg
6.9 4.1 3.8 3.5
(3.1) (1.8) (1.7) (1.6)
Fits Channel Sizes
Part No. B825-22 B825-52
B22 & B24 B52 & B54
B408SLBVNS Series
43/8”
STAND-OFF BRACKETS
(111.1)
• Material: 1/4” (6.3) • Standard Finishes: HDG, ZN, GRN • For pipe or rigid conduit sizes of 11/2” (32) and 2” (50) use with B501 Series ‘U’-Bolts • For strut channels 15/8” (41.3) wide use with B500 Series Square ‘U’-Bolts • Hardware is not included
Wt./C Lbs.
kg
2.0 1.0
(0.9) (0.4)
21/8” (53.5)
A
11/8” (28.6)
45/8”
15/16”
(117.5)
(33.3)
21/4”
1/2”
(57.1)
(12.7)
23/16” (55.6)
Part No. B408SLBVNS B408SLBVNS1 B408SLBVNS2
A In.
Wt./C (mm)
31/2” (88.9) 3” (76.2) 2” (50.8)
Lbs.
(27.0)
23/16”
kg
189 (85.7) 220 (99.8) 236 (107.0)
11/16”
(55.6)
(6) Slots 7/16” (11.1) x 11/8”
(28.6)
11/16”
21/4”
(27.0)
(57.1)
Strut Fittings
Reference page 72 for general fitting and standard finish specifications. Strut Systems
111
Dimensions The following dimensions apply to all fittings except as noted: Hole Spacing – 17/8” (47.6 mm) on center Hole Spacing –
13/16” (20.6 mm)
Hole Size – 9/16” (14.3 mm) diameter
from end
Thickness – 7/32” (5.5 mm) Width – 15/8” (41.3 mm)
Materials & Finishes (Unless otherwise noted) Finish Code PLN
Finish Plain
ZN
Electro-Plated Zinc
GRN HDG SS4 SS6 AL
DURA-GREEN™ Hot-Dipped Galvanized Stainless Steel Type 304 Stainless Steel Type 316 Aluminum
Specification ASTM A1018 33,000 PSI min. yield ASTM B633 SC3 Type III or ASTM A653 ASTM A123 ASTM A240 ASTM A240 ASTM B209
Note: A minimum order may apply on special material and finishes.
Load Data The load data published includes safety factor of 2.5 when used with 12 ga. (2.6) channel (safety factor = ratio of ultimate load to the design load). Use 1/2”-13 x 7/8” hex head cap screws and 1/2”-13 (N225 or TN225) channel nuts for the rated results.
Recommended Bolt Torque Bolt Size
1/4”-20
5/16”-18
3/8”-16
1/2”-13
Foot/Lbs.
6
11
19
50
Nm
8
15
26
68
Strut Fittings
See chart on page 112 for setscrew torque.
Hardware Nuts and bolts are not included with the fittings and must be ordered separately, unless noted.
Pre-Assembled Fittings Some fittings are available with hex head cap screws and channel nuts pre-assembled. These fittings and finishes will be flagged using the following symbol. ZN
PA
GRN
Metric Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.
72
Strut Systems
Flat Plate Fittings B200-B202-2
SQUARE WASHER
• Standard finishes: ZN, GRN, HDG, SS4, SS6, AL
Part No. B200 B201 B202 B202-1 B202-2
15/8” (41.3)
Hole Size
A
B129 TWO HOLE SPLICE PLATE
Wt./C A 3/8” 7/16” 9/16” 11/16” 13/16”
(A) (9.5) (11.1) (14.2) (17.4) (20.6)
Bolt Size 5/16” (7.9) 3/8” (9.5) 1/2” (12.7) 5/8” (15.9) 3/4” (19.0)
Lbs.
kg
18 18 17 16 15
(8.1) (8.1)
• Standard finishes: ZN, GRN • Wt./C 37 Lbs. (16.8 kg)
PA
ZN GRN
(7.7) (7.2)
31/2”
(6.8)
(88.9)
B200D-B202-2D
NO TWIST SQUARE WASHER
• Standard finishes: ZN, GRN, HDG, SS4, SS6, AL
Part No. B200D B201D B202D B202-1D B202-2D
15/8” (41.3)
A
Hole Size
Wt./C A
(A)
Bolt Size
3/8”
(9.5)
5/16”
7/16”
(11.1)
3/8”
(9.5)
9/16”
(14.2)
1/2”
(12.7)
11/16” (17.4) 13/16” (20.6)
5/8”
(15.9)
3/4”
(19.0)
(7.9)
Lbs.
kg
18 18 17 16 15
(8.1) (8.1) (7.7) (7.2) (6.8)
B340
B528
B141
TWO HOLE SPLICE PLATE
TWO HOLE SPLICE PLATE
THREE HOLE SPLICE PLATE
• Standard finishes: ZN, GRN • Wt./C 34 Lbs. (15.4 kg)
• Standard finishes: ZN, GRN • Wt./C 50 Lbs. (22.7 kg)
• Standard finishes: ZN, GRN • Wt./C 55 Lbs. (24.9 kg)
PA 15/16”
15/8” (41.3)
ZN GRN
21/2”
53/8” (136.5)
(63.5)
(33.3)
31/4” (82.5)
45/8” (117.5)
B557
B341
B342
THREE HOLE SPLICE PLATE
FOUR HOLE SPLICE PLATE
FIVE HOLE SPLICE PLATE
• Standard finishes: ZN, GRN • Wt./C 50 Lbs. (22.7 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN • Wt./C 96 Lbs. (43.5 kg)
PA
47/8”
ZN GRN
(123.8)
71/4”
15/8”
15/8” (41.3)
(41.3)
PA Reference page 72 for general fitting and standard finish specifications.
Strut Systems
Strut Fittings
(184.1)
91/8” (231.8)
73
Preassembled fitting.
Flat Plate Fittings B138
B139
B504
TWO HOLE SWIVEL PLATE
THREE HOLE SWIVEL PLATE
FOUR HOLE SPLICE PLATE
• Standard finishes: ZN, GRN • Wt./C 48 Lbs. (21.8 kg)
• Standard finishes: ZN, GRN • Wt./C 69 Lbs. (31.3 kg)
• Standard finishes: ZN, GRN • Wt./C 73 Lbs. (33.1 kg)
45/8” (117.5)
61/2” (165.1)
3” (76.2)
17/8”
15/8”
31/2”
(41.3)
(88.9)
3”
31/4”
(76.2)
(82.5)
(47.6)
B140
B143
B133
THREE HOLE CORNER PLATE
FOUR HOLE CORNER PLATE
FOUR HOLE TEE PLATE
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 56 Lbs. (25.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 75 Lbs. (34.0 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 75 Lbs. (34.0 kg)
PA
ZN GRN
PA
ZN GRN
PA
31/2”
ZN GRN
31/2” (88.9)
(88.9)
31/2” (88.9)
53/8” (136.5)
31/2” (88.9)
53/8” (136.5)
B132
B135
B142
FIVE HOLE CROSS PLATE
THREE HOLE CORNER GUSSET PLATE
FOUR HOLE CORNER GUSSET PLATE
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 102 Lbs. (46.2 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
PA
ZN GRN
PA 53/8” (136.5)
ZN GRN
31/2” 31/2”
Strut Fittings
(88.9)
(88.9)
31/2 (88.9) 53/8” (136.5)
53/8”
PA
Preassembled fitting. Reference page 72 for general fitting and standard finish specifications.
74
Strut Systems
Flat Plate Fittings B137
B556
B337
FOUR HOLE CORNER GUSSET PLATE
FIVE HOLE CORNER GUSSET PLATE
THREE HOLE TEE GUSSET PLATE
• Standard finishes: ZN, GRN • Wt./C 273 Lbs. (123.8 kg)
• Standard finishes: ZN, GRN • Wt./C 145 Lbs. (65.8 kg)
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
75/8”
25/16” (58.7)
(193.7) 13 5 /16” (147.6)
1”
31/2”
53/8” 75/8” (193.7)
(25.4)
(88.9)
(136.5)
53/8” (136.5)
31/2”
31/2”
(88.9)
(88.9)
1” (25.4)
B432
B136
B532
FOUR HOLE TEE GUSSET PLATE FOUR HOLE TEE GUSSET PLATE FIVE HOLE TEE GUSSET PLATE • Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 143 Lbs. (64.8 kg)
31/2”
31/2”
(88.9)
(88.9)
53/8” (136.5)
53/8” (136.5)
53/8” (136.5) 53/8” (136.5)
B339
B568
B334
SIX HOLE TEE GUSSET PLATE
SIX HOLE CROSS GUSSET PLATE
SEVEN HOLE CROSS GUSSET PLATE
• Standard finishes: ZN, GRN • Wt./C 166 Lbs. (75.3 kg)
• Standard finishes: ZN, GRN • Wt./C 232 Lbs. (105.2 kg)
• Standard finishes: ZN, GRN • Wt./C 149 Lbs. (67.6 kg)
31/2” (88.9)
91/8” (231.8)
91/8” (231.8)
31/2”
53/8” (136.5)
(88.9)
Reference page 75 for general fitting and standard finish specifications. Strut Systems
75
Strut Fittings
91/8” (231.8)
90° Angle Fittings B420-378
B420-578
B420-778
ONE HOLE CORNER ANGLE
ONE HOLE CORNER ANGLE
ONE HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 60 Lbs. (27.2 kg)
• Standard finishes: ZN, GRN • Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN • Wt./C 107 Lbs. (48.5 kg)
17/8” 17/8”
17/8”
(47.6)
(47.6)
(47.6)
77/8” (200.0)
57/8” (149.2)
37/8” (98.4)
B420-978
B101
B230
ONE HOLE CORNER ANGLE
TWO HOLE CORNER ANGLE
TWO HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 129 Lbs. (58.5 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 37 Lbs. (16.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 37 Lbs. (16.8 kg)
PA
ZN GRN
PA
15/8”
ZN GRN
17/8”
(41.3)
17/8”
(47.6)
(47.6)
97/8” (250.8)
21/16” (52.4)
25/16” (58.7)
B231
B359
B360
TWO HOLE “NO-TWIST” CORNER ANGLE
TWO HOLE CORNER ANGLE
TWO HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 48 Lbs. (21.8 kg)
• Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 41 Lbs. (18.6 kg)
PA
ZN GRN
Strut Fittings
3”
31/2”
(76.2)
(88.9)
21/4” (57.1)
21/4”
17/8”
(57.1)
PA
(47.6)
17/8” (47.6)
Preassembled fitting. Reference page 72 for general fitting and standard finish specifications.
76
Strut Systems
90° Angle Fittings B361
B102
B103
TWO HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 60 Lbs. (27.2 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 56 Lbs. (25.4 kg) • Wt./C 56 Lbs. (25.4 kg)
PA
ZN GRN
ZN GRN
PA
15/8”
31/2”
4”
(41.3)
(88.9)
(101.6)
41/8” (104.8)
17/8”
21/4”
(47.6)
(57.1)
B232
B374
B529
THREE HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
THREE HOLE CORNER ANGLE
• Standard finishes: ZN, GRN, HDG, SS4 • Standard finishes: ZN, GRN, HDG • Wt./C 56 Lbs. (25.4 kg) • Wt./C 56 Lbs. (25.4 kg)
PA
ZN GRN
PA
ZN GRN
• Standard finishes: ZN, GRN • Wt./C 78 Lbs. (35.4 kg)
3”
21/16” 15/16”
(52.4)
(76.2)
(33.3)
17/8” (47.6)
47/8” (123.8)
315/16”
33/4”
(100.0)
(95.2)
15/16” (33.3)
21/2” (63.5)
B104
B115
B558
FOUR HOLE CORNER ANGLE
FOUR HOLE CORNER ANGLE
FOUR HOLE CORNER ANGLE
• Standard finishes: ZN, GRN, HDG, SS4, SS6, AL • Wt./C 78 Lbs. (35.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN • Wt./C 73 Lbs. (33.1 kg)
PA
ZN GRN
PA 31/2”
ZN GRN
15/8” (41.3)
33/4” (95.2)
(88.9)
Strut Fittings
21/4” (57.1)
41/8” (104.8) 315/16” (100.0)
15/8”
31/4”
(41.3)
(82.5)
PA Reference page 72 for general fitting and standard finish specifications. Strut Systems
77
Preassembled fitting.
90° Angle Fittings B235R
B235L
B236R
THREE HOLE (RIGHT HAND) OFFSET BENT ANGLE
THREE HOLE (LEFT HAND) OFFSET BENT ANGLE
THREE HOLE (RIGHT HAND) OFFSET BENT ANGLE
• 15/8” (41.3) from center to center of the holes that are shown with bolt heads • Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• 15/8” (41.3) from center to center of the holes that are shown with bolt heads • Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN • Wt./C 65 Lbs. (29.5 kg)
17/8”
31/4”
31/4”
17/8”
(47.6)
(82.5)
(82.5)
(47.6)
21/16” (52.4)
17/8”
31/2”
(47.6)
21/16”
21/16”
(52.4)
(52.4)
(88.9)
B236L
B237
B357
THREE HOLE (LEFT HAND) OFFSET BENT ANGLE
THREE HOLE OFFSET BENT TEE
FOUR HOLE OFFSET BENT TEE
• Standard finishes: ZN, GRN • Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN, GRN • Wt./C 77 Lbs. (34.9 kg)
• Standard finishes: ZN, GRN • Wt./C 65 Lbs. (29.5 kg)
47/8” (123.8)
17/8”
31/2”
2”
(47.6)
(88.9)
21/16”
(50.8)
(52.4)
53/8” (136.5)
21/16”
Strut Fittings
(52.4)
B238R
B238L
B239
FOUR HOLE (RIGHT HAND) OFFSET BENT TEE
FOUR HOLE (LEFT HAND) OFFSET BENT TEE
FIVE HOLE OFFSET BENT TEE
• Standard finishes: ZN, GRN • Wt./C 76 Lbs. (34.5 kg)
• Standard finishes: ZN, GRN • Wt./C 76 Lbs. (34.5 kg)
21/16”
21/16”
(52.4)
(52.4)
• Standard finishes: ZN, GRN • Wt./C 96 Lbs. (43.5 kg)
21/16” (52.4)
33/4” (95.2)
31/2”
31/2”
(88.9)
(88.9)
53/8” (136.5)
33/4”
31/2”
(95.2)
(88.9)
Reference page 72 for general fitting and standard finish specifications.
78
Strut Systems
90° Angle Fittings B844
B844W
B888W
UNIVERSAL SHELF BRACKET
UNIVERSAL SHELF BRACKET• Standard finishes: ZN, GRN, HDG, SS4 WELDED
UNIVERSAL SHELF BRACKETWELDED
• Wt./C 132 Lbs. (59.9 kg)
• Standard finishes: ZN, GRN • Wt./C 197 Lbs. (89.4 kg)
• Standard finishes: ZN, GRN • Wt./C 134 Lbs. (60.8 kg)
4”
4”
(101.6)
(101.6)
513/16” (147.6) Welded Corner
17/8” (47.6)
4”
4”
(101.6)
(101.6)
17/8”
17/8”
(47.6)
(47.6)
53/8” (136.5)
B234R
B234L
B134R
FOUR HOLE (RIGHT HAND) CORNER GUSSET
FOUR HOLE (LEFT HAND) CORNER GUSSET
FOUR HOLE (RIGHT HAND) CORNER GUSSET
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
31/2” 15/8”
(88.9)
31/2” (88.9)
315/16”
15/8”
(100.0)
(41.3)
(41.3)
31/2” (88.9)
43/16”
43/16”
(106.3)
(106.3)
17/8” (47.6)
B134L
B125
B118
FOUR HOLE (LEFT HAND) CORNER GUSSET
THREE HOLE GUSSETTED SHELF ANGLE
FOUR HOLE GUSSETTED SHELF ANGLE
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 67 Lbs. (30.4 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 102 Lbs. (46.2 kg)
315/16”
31/2” 31/2”
(88.9)
15/8”
(88.9)
31/2”
15/8”
(88.9)
(41.3)
25/16” (58.7)
17/8” (47.6)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
79
(41.3)
41/8” (104.8)
Strut Fittings
(100.0)
90° Angle Fittings B485
B533
B126
FOUR HOLE GUSSETTED SHELF ANGLE
FIVE HOLE GUSSETTED SHELF ANGLE
FOUR HOLE GUSSETTED THREE WAY SHELF ANGLE
• Standard finishes: ZN, GRN • Wt./C 148 Lbs. (67.1 kg)
• Standard finishes: ZN, GRN • Wt./C 141 Lbs. (63.9 kg)
• Standard finishes: ZN, GRN • Wt./C 101 Lbs. (45.8 kg)
17/8” 15/8”
(47.6)
(41.3)
31/2”
41/8”
(88.9)
(104.8)
31/2” (88.9)
21/4”
53/8”
53/8”
(136.5)
(57.1)
(136.5)
315/16” (100.0)
B127
B503R
B503L
FIVE HOLE GUSSETTED THREE WAY SHELF ANGLE
SIX HOLE (RIGHT HAND) GUSSETTED CORNER CONNECTION
SIX HOLE (LEFT HAND) GUSSETTED CORNER CONNECTION
• Standard finishes: ZN, GRN • Wt./C 229 Lbs. (103.9 kg)
• Standard finishes: ZN, GRN • Wt./C 229 Lbs. (103.9 kg)
• Standard finishes: ZN, GRN • Wt./C 135 Lbs. (61.2 kg)
31/2”
33/4”
(88.9)
(95.2)
31/2” (88.9)
33/4”
43/16” 43/16”
(95.2)
43/16”
(106.3)
(106.3)
(106.3)
53/8” (136.5)
53/8” (136.5)
15/8”
15/8”
(41.3)
(41.3)
B663
B371
B372
SEVEN HOLE GUSSETTED CORNER CONNECTION
TWO HOLE ADJUSTABLE CORNER ANGLE • Standard finishes: ZN, GRN • Wt./C 41 Lbs. (18.6 kg)
TWO HOLE ADJUSTABLE CORNER ANGLE • Standard finishes: ZN, GRN • Wt./C 38 Lbs. (17.2 kg)
• Standard finishes: ZN, GRN • Wt./C 289 Lbs. (131.1 kg)
53/8” (136.5)
Strut Fittings
25/8” 53/8”
43/16”
(136.5)
25/8”
(66.7)
(66.7)
(106.3)
9/16”
9/16”
(14.3) 9/16”
(14.3)
x 11/2”
Slot
(50.8)
(38.1)
(14.3)
2” 9/16”
(14.3)
x 11/2”
Slot
(38.1)
15/8” (41.3)
15/8” (41.3)
Reference page 72 for general fitting and standard finish specifications.
80
Strut Systems
90° Angle Fittings B496
B496-1
B371-2
TWO HOLE ADJUSTABLE CORNER ANGLE • Standard finishes: ZN, GRN • Wt./C 85 Lbs. (38.5 kg)
TWO HOLE ADJUSTABLE CORNER ANGLE
THREE HOLE ADJUSTABLE CORNER ANGLE
• Standard finishes: ZN, GRN, HDG • Wt./C 58 Lbs. (26.3 kg)
• Standard finishes: ZN, GRN • Wt./C 61 Lbs. (27.6 kg)
23/8”
23/8”
(60.3)
(60.3)
15/16”
47/8”
67/8”
(33.3) 9/16”
(123.8)
(174.6) 9/16”
x 29/16”
(14.3)
(65.1)
Slot
17/8”
17/8”
(47.6)
(47.6)
9/16”
x 29/16”
(14.3)
(65.1)
(14.3)
x 11/2”
Slot
25/8”
(38.1)
Slot
(66.7)
37/8” (98.4)
B104SH
B461
B112
THREE HOLE ADJUSTABLE CORNER ANGLE
TWO HOLE ADJUSTABLE CORNER ANGLE
FOUR HOLE ADJUSTABLE CORNER ANGLE
• Standard finishes: ZN, GRN • Wt./C 68 Lbs. (30.8 kg)
• Standard finishes: ZN, GRN • Wt./C 87 Lbs. (39.4 kg)
• Standard finishes: ZN, GRN • Wt./C 180 Lbs. (81.6 kg)
31/2”
31/2”
(88.9)
(88.9)
21/4” (57.1) 9/16”
1/2” (12.7)
13/32” (10.3)
31/2” (88.9)
9/16”
x 29/16”
(14.3)
(65.1)
Slot
41/8” (104.8)
9/16”
x 29/16”
(14.3)
(65.1)
x 11/2”
(14.3)
Slot -(2)
(38.1)
33/4” (95.2)
4” (101.6)
Slot
65/8” (168.3)
B113
B109S
B521
FOUR HOLE ADJUSTABLE CORNER ANGLE
TWO HOLE TAPPED CORNER ANGLE
TWO HOLE BUS DUCT ANGLE
• Standard finishes: ZN, GRN • Wt./C 256 Lbs. (116.1 kg)
• Standard finishes: ZN, GRN • Wt./C 33 Lbs. (14.9 kg)
x 11/2”
(14.3)
Slot -(2)
(38.1)
33/4”
5/16”-18 Tapped
17/8”
(95.2)
1/2” (12.7)
17/8” (47.6)
(47.6)
6” (152.4)
15/8” 85/8” (219.1)
(41.3)
17/8” (47.6)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
2” (50.8)
81
Strut Fittings
9/16”
• Standard finishes: ZN, GRN • Wt./C 37 Lbs. (16.8 kg)
Angular Fittings B147-B152
B243-B253
TWO HOLE OPEN ANGLE
FOUR HOLE OPEN ANGLE
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
23/8” (60.3)
11/16” (27.0)
Part No.
A
B147 B148 B149 B150 B151 B152
821/2°
Wt./C Lbs.
75° 671/2° 60° 521/2° 371/2°
31/4” A
kg
(82.5)
11/16” (27.0)
63
(28.6)
B162-B165
A
(27.0)
35/16” (84.1)
B162 B163 B164 B165
30° 221/2° 15° 71/2°
Wt./C kg
11/16”
21/16” (52.4)
(27.0)
59
15° 221/2° 30° 371/2° 45° 521/2° 60° 671/2° 75° 821/2°
kg
311/16” (93.6)
A
31/2” 77
(34.9)
(88.9)
• Standard finishes: ZN, GRN
11/16”
Lbs.
B243 B244 B245 B246 B247 B248 B249 B250 B251 B252 B253
71/2°
Wt./C Lbs.
TWO HOLE OPEN SHORT ANGLE
• Standard finishes: ZN, GRN
A
A
B322-B332
TWO HOLE OPEN ANGLE
Part No.
Part No.
(26.7)
B154 TWO HOLE OPEN ANGLE • Standard finishes: ZN, GRN, SS4 • Wt./C 58 Lbs. (26.3 kg)
Part No.
A
B322 B323 B324 B325 B326 B327 B328 B329 B330 B331 B332
71/2°
Wt./C Lbs.
15° 221/2° 30° 371/2° 45° 521/2° 60° 671/2° 75° 821/2°
kg
A 13/4” (44.4)
15/8” (41.3)
35
(15.9)
B522
B488
THREE HOLE 95° OPEN ANGLE FITTING
TWO HOLE LEG CONNECTION
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
Strut Fittings
17/8” (47.6)
3” (76.2)
5° 5°
5°
11/16” (27.0)
25/16” 45°
(58.7)
11/16”
35/8” (92.1)
31/4”
(27.0)
(82.5)
Reference page 72 for general fitting and standard finish specifications.
82
Strut Systems
Angular Fittings B156 - B161
B155
TWO HOLE CLOSED ANGLE
TWO HOLE CLOSED ANGLE
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 63 Lbs. (28.6 kg)
PA Part No.
A
B156 B157 B158 B159 B160 B161
821/2° 75° 671/2° 60° 521/2° 371/2°
13/16”
13/16”
(20.6)
(20.6)
Wt./C Lbs.
ZN GRN
33/16”
kg
31/2” (88.9)
(80.9) 13/16”
45°
(20.6)
56
(25.4)
A 13/16”
21/2”
(20.6)
21/2”
(63.5)
(63.5)
B363 - B369
B335-2 SERIES
FOUR HOLE CLOSED ANGLE
THREE HOLE ADJUSTABLE HINGE
• Standard finishes: ZN, GRN
• OSHPD approved for Seismic Zone 4 • Standard finishes: ZN, GRN
5”
H
(127.0)
Hole Size This Hole Only
Part No.
A
B363 B364 B365 B366 B367 B368 B369
821/2° 75° 671/2° 60° 521/2° 45° 371/2°
411/16”
Wt./C Lbs.
(119.1)
kg
43/8”
213/16”
(111.1)
(71.4)
95
(43.1)
Part No. & Size B335-2-3/8 B335-2-1/2 B335-2-5/8 B335-2-3/4
A
Hole Size H 7/16” (11.1) 9/16” (14.3) 11/16” (17.4) 13/16” (20.6)
Wt./C Lbs.
kg
96 94 92 90
(43.2) (42.3) (41.4) (40.5)
B335
B335V
B335-1
FOUR HOLE ADJUSTABLE HINGE
TWO HOLE HALF HINGE
TWO HOLE ADJUSTABLE HINGE
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN • Wt./C 78 Lbs. (35.4 kg)
• Standard finishes: ZN, GRN • Wt./C 110 Lbs. (49.9 kg)
411/16” (119.1)
Hole Size H 9/16” (14.3) 11/16” (17.4) 13/16” (20.6)
Wt./C Lbs.
kg
53 54 55
(24.1) (24.5) (24.9)
213/16”
H
(71.4)
Strut Fittings
Part No. & Size B335V-1/2 B335V-5/8 B335V-3/4
213/16” (71.4)
411/16”
411/16”
(119.1)
(119.1)
PA Reference page 72 for general fitting and standard finish specifications. Strut Systems
83
Preassembled fitting.
Angular Fittings B634
B635
SINGLE CHANNEL ADJUSTABLE BRACE
DOUBLE CHANNEL ADJUSTABLE BRACE
• Standard finishes: ZN, GRN • Wt./C 306 Lbs. (138.8 kg)
• Standard finishes: ZN, GRN • Wt./C 518 Lbs. (234.9 kg)
13/16”
13/16”
(20.6)
(20.6)
15/8”
15/8”
(41.3)
(41.3)
30° MIN.
17/8”
17/8”
(47.6)
(47.6)
33/4”
33/4”
(95.2) 53/8”
(95.2) 53/8”
(136.5)
(136.5)
B129
B650 SERIES SEISMIC RETROFIT BRACKET • • • • •
OSHPD approved for Seismic Zone 4. Available for 3/8”, 1/2”, 5/8”, and 3/4” threaded rods. Allows installer to easily brace existing trapeze supports. Includes: Bracket, B129 plate, & key. Hardware sold separately. Standard finish: ZN, GRN
ATR
Bracket
Key Part No. & Size
For Rod Size
B650-3/8
3/8”
B650-1/2 B650-5/8 B650-3/4
1/2” 5/8” 3/4”
TL
LL
Wt./C
Lbs.
kN
Lbs.
kN
Lbs.
kg
1100 1500 1500 1500
(4.89)
1100 1500 1500 1500
(4.89)
92 97 95 107
(41.4)
(6.67) (6.67) (6.67)
(6.67) (6.67) (6.67)
Longitudina l Load (LL)
(43.6) (42.7)
Transverse Load (TL)
(48.5)
B633 ADJUSTABLE SEISMIC HINGE FITTING
Strut Fittings
• B633-1/2 thru B633-7/8 - OSHPD approved for Seismic Zone 4. • Use 1/2” Bolt & Channel Nut on two hole side of Connector Fitting (Torque to 50 ft.-lbs.) • Allows for swivel in two planes. • Standard finish: ZN
H 33/4” (95.2)
B
15/8” (41.3)
Part No. & Size
A
B633-1/2
31/2”
B633-5/8 B633-3/4 B633-7/8 B633-1 B633-11/8 B633-11/4
31/2” 31/2” 39/16” 39/16” 39/16” 37/8”
Hole Size H
B (82.5)
15/8”
(82.5)
15/8” 15/8” 2” 2” 2” 21/4”
(82.5) (90.5) (90.5) (90.5) (98.4)
(41.3)
9/16”
(14.3)
(41.3)
11/16”
(17.4)
(41.3)
13/16”
(20.6)
(50.8)
15/16”
(23.8)
(50.8) 11/16”
(27.0)
13/16”
(30.2)
(57.1) 15/16”
(33.3)
(50.8)
Wt./C Lbs.
kg
92 97 95 107 120 104 114
(41.4)
A
(43.6) (42.7) (48.5) (54.0) (47.2) (51.7)
Reference page 72 for general fitting and standard finish specifications.
84
Strut Systems
Braces B261 - TWO HOLE 45° KNEE BRACE • Standard finishes: ZN, GRN • Design load determined by testing using a B335 hinged corner connection. • Load ratings are for brace members only. Do not exceed allowable beam or column loads for strut channels. • Safety Factor of 3 Part No. B261-8 B261-12 B261-16 B261-18 B261-24 B261-36
Design Load A 8” 12” 165/8” 18” 24” 36”
B
(B)
Lbs.
kN
Lbs.
kg
(203.2)
73/8”
(187.3)
1500 1020 530 450 250 110
(6.67)
119 165 218 234 303 441
(54.0)
(422.3) 133/8” (339.7) (457.2) 147/16” (366.7) (609.6) 1811/16” (474.7) (914.4) 273/16” (690.6)
(4.54) (2.36) (2.00) (1.11) (.49)
(41.3)
Design Load
(74.8) (98.9)
B A
Wt./C
(A)
(304.8) 101/8” (257.2)
15/8”
45°
15/8” (41.3)
(106.1) (137.4)
B
(200.0)
B631 - TWO HOLE 45° TUBING KNEE BRACE • • • • •
1” (25.4) Square steel tubing Material: ASTM A513 Standard finishes: ZN, GRN Design load determined by testing using a B335 hinged corner connection. Load ratings are for brace members only. Do not exceed allowable beam or column loads for strut channels. • Safety Factor of 3 Design Load
Part No.
A
B631-18 B631-24 B631-30 B631-36 B631-42 B631-48 B631-54 B631-60 B631-72 B631-84 B631-96
18” 24” 30” 36” 42” 48” 54” 60” 72” 84” 96”
(A) (457.2) (609.6) (762.0) (914.4) (1066.8) (1219.2) (1371.6) (1524.0) (1828.8) (2133.6) (2438.4)
kN
Lbs.
kg
1500 1500 1500 1500 1230 940 740 600 420 310 240
(6.67)
145 186 225 266 307 348 389 430 508 589 669
(65.8)
(6.67) (6.67) (5.47) (4.18) (3.29) (2.67) (1.87) (1.38) (1.07)
A
Wt./C
Lbs.
(6.67)
Design Load
(84.4) (102.0) (120.6) (139.2) (157.8) (176.4) (195.0) (230.4)
13/4”
(267.2)
(44.4)
(303.5)
B632 - TWO HOLE STRAIGHT TUBING BRACE • 1” (25.4) Square steel tubing • Material: ASTM A513 • Standard finishes: ZN, GRN
A
(A)
Lbs.
Wt./C kg
B632-18 B632-24 B632-30 B632-36 B632-42 B632-48 B632-54 B632-60 B632-72 B632-84 B632-96
18” 24” 30” 36” 42” 48” 54” 60” 72” 84” 96”
(457.2)
133 174 215 256 295 335 380 420 500 585 670
(60.3)
13/4”
(78.9)
(44.4)
(609.6) (762.0) (914.4) (1066.8) (1219.2) (1371.6) (1524.0) (1828.8) (2133.6) (2438.4)
(97.5) (116.1) (133.8)
A
(151.9) (172.3) (190.5) (226.8) (265.3) (303.9)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
85
Strut Fittings
Part No.
Clevis Fittings B169
B168
B167
TWO HOLE SPLICE CLEVIS FOR B52
THREE HOLE SPLICE CLEVIS FOR B52
FOUR HOLE SPLICE CLEVIS FOR B52
• Standard finishes: ZN, GRN • Wt./C 84 Lbs. (38.1 kg)
• Standard finishes: ZN, GRN • Wt./C 126 Lbs. (57.1 kg)
• Standard finishes: ZN, GRN • Wt./C 178 Lbs. (80.7 kg)
PA
31/2” 1/4”
GRN
71/4” (184.1)
53/8”
(88.9)
(136.5) 1/4”
(6.3)
1/4”
(6.3)
(6.3)
B170
B171
B172
TWO HOLE SPLICE CLEVIS FOR B22 OR B52A
THREE HOLE SPLICE CLEVIS FOR B22 OR B52A
FOUR HOLE SPLICE CLEVIS FOR B22 OR B52A
• Standard finishes: ZN, GRN • Wt./C 123 Lbs. (55.8 kg)
• Standard finishes: ZN, GRN • Wt./C 195 Lbs. (88.4 kg)
• Standard finishes: ZN, GRN • Wt./C 266 Lbs. (120.6 kg)
PA
31/2” 1/4”
ZN GRN
53/8” (136.5)
(88.9)
(6.3)
71/4” (184.1)
1/4”
1/4”
(6.3)
(6.3)
B172-12
B172-22A
B450
FOUR HOLE SPLICE CLEVIS FOR B12
FOUR HOLE SPLICE CLEVIS FOR B11 OR B22A
U-WASHER
• Standard finishes: ZN, GRN • Wt./C 326 Lbs. (147.8 kg)
• Standard finishes: ZN, GRN • Wt./C 406 Lbs. (184.1 kg)
PA
• Material: ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN
H
GRN
Hole Size 15/32” (11.9)
Strut Fittings
15/8” 11 Gauge (3.1)
Part No. & Size
71/4”
71/4” (184.1)
(184.1) 1/4” (6.3)
1/4” (6.3)
PA
(41.3)
Hole Size H
B450-1/4
5/16”
B450-3/8 B450-1/2 B450-5/8 B450-3/4
7/16” (11.1) 9/16” (14.3)
(7.9)
11/16” (17.4) 13/16” (20.6)
Wt./C Lbs.
kg
14 14 13 13 13
(6.3) (6.3) (5.8) (5.8) (5.8)
Preassembled fitting. Reference page 72 for general fitting and standard finish specifications.
86
Strut Systems
‘U’ Fittings B527
B116-52
B116-42
THREE HOLE OFFSET PLATE CONNECTION
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN • Wt./C 75 Lbs. (34.0 kg)
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
1/2” (12.7)
13/16”
1”
(20.6)
(25.4)
57/16”
57/16”
(138.1)
(138.1)
55/16” (134.9)
B116-32
B116-32A
B116-12
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 84 Lbs. (38.1 kg)
• Standard finishes: ZN, GRN • Wt./C 116 Lbs. (52.6 kg)
• Standard finishes: ZN, GRN • Wt./C 108 Lbs. (49.0 kg)
13/8”
23/4”
27/16”
(69.8)
(61.9)
(34.9)
57/16”
57/16”
57/16”
(138.1)
(138.1)
(138.1)
B107
B107-22A
B588
FIVE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
THREE HOLE U-SUPPORT
• Standard finishes: ZN, GRN, HDG • Wt./C 85 Lbs. (38.5 kg)
• Standard finishes: ZN, GRN • Wt./C 126 Lbs. (57.1 kg)
• Standard finishes: ZN, GRN • Wt./C 157 Lbs. (71.2 kg)
PA
ZN GRN
15/8”
47/8” (123.8)
Strut Fittings
31/4” (82.5)
(41.3)
57/16” (138.1)
57/16” (138.1)
57/16” (138.1)
PA Reference page 72 for general fitting and standard finish specifications. Strut Systems
87
Preassembled fitting.
‘U’ Fittings B412
B107S
B596
THREE HOLE OFFSET U-SUPPORT
FIVE HOLE U-SUPPORT
THREE HOLE SWIVEL CLEVIS
• Material: 7 Gauge (4.5) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN, GRN • Wt./C 51 Lbs. (23.1 kg)
• Material: 7 Gauge (4.5) • Standard finishes: ZN, GRN • Wt./C 53 Lbs. (24.0 kg)
• Standard finishes: ZN, GRN • Wt./C 89 Lbs. (40.3 kg)
57/16” (138.1)
33/4”
13/16”
(95.2)
(20.6)
3 1” 1 /8”
17/8”
(25.4)
(47.6)
(34.9)
21/4” (57.1)
7/16” (11.1) Dia. 4 Holes 9/16” (14.3) Dia.
13/4” (44.4)
15/8”
15/8”
(41.3)
(41.3)
B578
B594
B266
THREE HOLE LIGHT-WEIGHT U-SUPPORT
FIVE HOLE U-SUPPORT
SIX HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 106 Lbs. (48.1 kg)
• Standard finishes: ZN, GRN • Wt./C 105 Lbs. (47.6 kg)
• Material: 10 Gauge (3.4) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 18 Lbs. (8.1 kg)
17/8”
35/16”
121/32”
(84.1)
(42.1)
(47.6)
311/16” (93.6)
3/4” (19.0)
15/8” (41.3)
13/32” (10.3) 9/32” (7.1) Dia. 3 Holes
15/8” (41.3)
71/32”
35/16”
(178.6)
111/16”
71/16”
(42.8)
(84.1)
(179.4)
B425
B581
B519
SIX HOLE U-SUPPORT
EIGHT HOLE U-SUPPORT
EIGHT HOLE U-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 167 Lbs. (75.7 kg)
• Standard finishes: ZN, GRN • Wt./C 201 Lbs. (91.2 kg)
• Standard finishes: ZN, GRN • Wt./C 266 Lbs. (102.5 kg)
111/16” Strut Fittings
(42.9)
31/2”
31/2”
(88.9)
(88.9)
15/8”
31/2”
(41.3)
(88.9)
31/2” (88.9)
15/8” (41.3)
57/16” (138.1)
71/16” (179.4)
513/32” (137.3)
Reference page 72 for general fitting and standard finish specifications.
88
Strut Systems
‘U’ Fittings B333
B451
SLOTTED THREE HOLE U-SUPPORT FOR B22
SLOTTED THREE HOLE U-SUPPORT WITH GUSSET FOR B22
A
• Standard finishes: ZN, GRN
• Consists of B333-1, 2, or 3 with gusset plate welded on back. • Material: ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN
C
9/16”
(14.3)
x 11/2”
A
Slots-(2)
(38.1) 9/16”
(14.3)
x 11/2”
Slots-(2)
(38.1)
15/8”
B
(41.3)
Part No.
Wt./C A
B333-1 B333-2 B333-3
(A)
B
(B)
C
71/2” (190.5) 15/16” (33.3) 81/2” (215.9) 115/16” (49.2) 103/8” (263.5) 27/8” (73.0)
(C)
Lbs.
27/8”
(73.0) 103 33/8” (85.7) 115 45/16” (109.5) 135
Part No.
kg
A
B451-1 B451-2 B451-3
(46.7) (52.1) (61.2)
B408
Wt./C (A)
1
7 /2” (190.5) 81/2” (215.9) 103/8” (263.5)
Lbs.
kg
137 156 172
(62.1) (70.7) (78.0)
B358
TWO HOLE BUS DUCT CLEVIS
TWO HOLE CLEVIS
1/2”
• Standard finishes: ZN, GRN
(12.7)
13/16”
• Standard finishes: ZN, GRN
(20.6) 9/16” (14.3) DIA. 2 HOLES
17/8” (47.6)
17/8” (47.6)
A
Part No.
A
Wt./C A
B408-1 B408-2 B408-3
(A)
Lbs.
213/32” (61.1) 58 325/32” (96.0) 76 43/4” (762.0) 88
kg (26.3)
13/16” (20.6)
(34.5) (39.9)
Part No.
A
Wt./C
B358-4 B358-5 B358-6 B358-7 B358-8
4” 5” 6” 7” 8”
(A)
Lbs.
89 93 (152.4) 106 (177.8) 118 (203.2) 132
kg
(101.6)
(40.3)
(127.0)
(42.2) (48.1)
13/16”
(53.5)
(20.6)
(59.9)
B173
B595
B405
FOUR HOLE CLEVIS
THREE HOLE CLEVIS
• Standard finishes: ZN, GRN • Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN, GRN • Wt./C 75 Lbs. (34.0 kg)
THREE HOLE SUSPENSION CLEVIS • Standard finishes: ZN, GRN • Wt./C 75 Lbs. (34.0 kg)
37/16”
17/8” (47.6)
129/32” 35/16” (84.1)
121/32” (42.0)
(48.4)
35/16”
121/32” (42.0)
(84.1)
17/8” (47.6)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
89
Strut Fittings
(87.3)
(47.6)
17/8”
‘U’ Fittings B398-1
B415
THREE HOLE CUP SUPPORT
TWO HOLE BUS DUCT CONNECTION
• Standard finishes: ZN, GRN • Wt./C 73 Lbs. (33.1 kg)
• Standard finishes: ZN, GRN • Wt./C 56 Lbs. (25.4 kg)
17/8” (47.6)
111/16” (42.9)
23/32” (53.2)
11/16” (27.0)
15/8” (41.3)
111/16”
325/32”
(42.9)
(96.0)
1/2” (12.7)
11/16” (27.0)
B400
B400-1
B400-2
THREE STUD RING CONNECTION
ONE STUD RING CONNECTION
ONE STUD RING CONNECTION
• 1/2”-13 stud protrudes 1”
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 53 Lbs. (24.0 kg)
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 40 Lbs. (18.1 kg)
(25.4mm)
• Standard finishes: ZN • Wt./C 85 Lbs. (38.5 kg)
111/16” 23/16”
(42.9)
111/16” 111/16”
(42.9)
(47.6)
(47.6)
(42.9)
(55.6)
17/8” 17/8”
B400-3
B400-4
B536
TWO STUD RING CONNECTION
TWO STUD RING CONNECTION
TAPPED U-SUPPORT
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 59 Lbs. (26.7 kg)
• 1/2”-13 stud protrudes 1” (25.4mm) • Standard finishes: ZN • Wt./C 59 Lbs. (26.7 kg)
• Standard finishes: ZN • Wt./C 87 Lbs. (39.4 kg)
Strut Fittings
15/8” (41.3)
111/16” (42.9)
111/16” (42.9)
111/16” (42.9)
111/16” (42.9)
59/16” (141.3) Tapped 5/16”-18 (2) Holes
Reference page 72 for general fitting and standard finish specifications.
90
Strut Systems
‘Z’ Fittings B526
B106-52
B106-42
TWO HOLE OFFSET Z-SUPPORT
TWO HOLE Z-SUPPORT FOR B52
TWO HOLE Z-SUPPORT FOR B42
• Standard finishes: ZN, GRN • Wt./C 38 Lbs. (17.2 kg)
• Standard finishes: ZN, GRN • Wt./C 40 Lbs. (18.1 kg)
• Standard finishes: ZN, GRN • Wt./C 44 Lbs. (20.0 kg)
1/4” (6.3)
315/32”
13/16”
1”
(20.6)
(25.4)
(88.1)
15/8”
31/2”
31/2”
(88.9)
(88.9)
(41.3)
B106-32
B106-12
B105
TWO HOLE Z-SUPPORT FOR B32
TWO HOLE Z-SUPPORT FOR B12
THREE HOLE Z-SUPPORT FOR B22
• Standard finishes: ZN, GRN • Wt./C 51 Lbs. (23.1 kg)
• Standard finishes: ZN, GRN • Wt./C 63 Lbs. (28.6 kg)
• Standard finishes: ZN, GRN, HDG • Wt./C 51 Lbs. (23.1 kg)
15/8” (41.3)
27/16”
13/8”
(61.9)
(34.9)
31/2”
31/2”
31/2”
(88.9)
(88.9)
(88.9)
B110
B586
B108
THREE HOLE Z-SUPPORT FOR B11
TWO HOLE Z-SUPPORT
TWO HOLE OFFSET Z-SUPPORT
• Standard finishes: ZN, GRN • Wt./C 70 Lbs. (31.7 kg)
• Standard finishes: ZN, GRN • Wt./C 90 Lbs. (40.8 kg)
• Standard finishes: ZN, GRN • Wt./C 55 Lbs. (24.9 kg)
31/2” (88.9)
31/2”
31/2” (88.9)
Strut Fittings
(88.9)
21/8”
47/8”
15/8”
(123.8)
(54.0)
(41.3)
31/2” (88.9)
15/8” (41.3)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
91
‘Z’ Fittings B387
B407
TWO HOLE Z-BUS DUCT CONNECTION
TWO HOLE Z-SUPPORT
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
15/8”
31/2”
(41.3)
(88.9)
15/8”
31/2”
(41.3)
(88.9) 1/2” (12.7)
Part No. B387 B387-1 B387-2
A
(A)
Lbs.
43/4” (120.6) 325/32” (96.0) 213/32” (61.1)
kg
89 (40.3) 78 (35.4) 62 (28.1)
Wt./C Part No.
A
B407-4 4” B407-5 5” B407-6 6” B407-7 7” B407-8 8” B407-95/8 95/8”
Wt./C
A
A
(A)
Lbs.
kg
(101.6)
77 95 98 105 120 138
(34.9)
(127.0) (152.4) (177.8) (203.2) (244.5)
(43.1) (44.4) (47.6) (54.4) (62.6)
B534
B535
B111
TAPPED Z-SUPPORT
TAPPED Z-SUPPORT
• Standard finishes: ZN • Wt./C 51 Lbs. (23.1 kg)
• Standard finishes: ZN • Wt./C 50 Lbs. (22.7 kg)
THREE HOLE SHEATH CORNER CONNECTION
15/8”
15/8”
15/8”
(41.3)
• Standard finishes: ZN, GRN • Wt./C 68 Lbs. (30.8 kg)
31/2”
15/8”
(41.3)
(88.9)
(41.3)
(41.3)
31/2” (88.9)
15/8” 15/8”
15/8”
(41.3)
(41.3)
(41.3)
5/16”-18 Tapped Holes (2)
5/16”-18
Tapped Hole
15/8”
Strut Fittings
(41.3)
B538
B539
TAPPED CORNER CONNECTION
TAPPED CORNER CONNECTION
• Standard finishes: ZN • Wt./C 71 Lbs. (32.2 kg)
• Standard finishes: ZN • Wt./C 68 Lbs. (30.8 kg)
15/8” (41.3)
17/8” (47.6)
5/16”-18 Tapped Holes (4)
15/8” (41.3)
17/8” (47.6)
31/2” (88.9)
31/2” (88.9)
5/16”-18 Tapped Holes (2)
Reference page 72 for general fitting and standard finish specifications.
92
Strut Systems
‘Z’ Fittings B410-52
B410-32
B410-22
CHANNEL HANGER BRACKET FOR B52
CHANNEL HANGER BRACKET FOR B32
CHANNEL HANGER BRACKET FOR B22
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 6.7 Lbs. (3.0 kg)
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 8.3 Lbs. (3.7 kg)
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 9 Lbs. (4.1 kg)
13/16”
9/32” (7.1)
13/16”
13/16”
(20.6)
(20.6)
(20.6)
Dia. Hole
9/32” (7.1) Dia. Hole
9/32” (7.1) Dia. Hole
13/16” (20.6)
13/8”
15/8”
(34.9)
(41.3)
B410-12
B410-11
B580
CHANNEL HANGER BRACKET FOR B12
CHANNEL HANGER BRACKET FOR B11
FIVE HOLE GUSSETTED Z-SUPPORT
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 11.2 Lbs. (5.1 kg)
• Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN • Wt./C 13.4 Lbs. (6.1 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
9/32” (7.1)
(88.9)
(20.6)
(20.6)
Dia. Hole
31/2”
13/16”
13/16”
31/2” (88.9)
9/32” (7.1) Dia. Hole
31/4”
27/16”
(82.5)
(61.9)
15/8” (41.3)
B515
B428
ADJUSTABLE OFFSET GUSSETTED Z-SUPPORT
EIGHT HOLE GUSSETTED CORNER CONNECTION
• Standard finishes: ZN, GRN • Wt./C 93 Lbs. (42.2 kg)
• Standard finishes: ZN, GRN • Wt./C 203 Lbs. (92.1 kg)
15/32”
31/2”
53/4” (146.0)
(47.6)
(88.9)
37/8” (98.4)
9/16”
x 29/16”
(14.3)
(65.1)
Slots
Strut Fittings
(11.9)
53/4” (146.0)
17/8”
17/8” (47.6)
31/2” (88.9)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
93
Wing Fittings B267R
B267L
B270R
THREE HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
THREE HOLE SINGLE CORNER CONNECTION (LEFT HAND)
FOUR HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN • Wt./C 54 Lbs. (24.5 kg)
• Standard finishes: ZN, GRN • Wt./C 77 Lbs. (34.9 kg)
111/16” 21/16”
21/16”
(52.4)
(52.4)
(42.8)
21/16” (52.4)
15/8”
15/8”
(41.3)
(41.3)
31/2” (88.9)
31/2”
313/16”
(88.9)
(96.8)
B270L
B268R
B268L
FOUR HOLE SINGLE CORNER CONNECTION (LEFT HAND)
FIVE HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
FIVE HOLE SINGLE CORNER CONNECTION (LEFT HAND)
• Standard finishes: ZN, GRN • Wt./C 77 Lbs. (34.9 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
• Standard finishes: ZN, GRN • Wt./C 100 Lbs. (45.3 kg)
111/16” (42.8)
21/16”
315/16” (100.0) 5 1 /8”
(52.4)
315/16” (100.0)
(41.3)
313/16”
15/8” (41.3)
31/2”
(96.8)
31/2”
(88.9)
(88.9)
B269R
B269L
B119
SIX HOLE SINGLE CORNER CONNECTION (RIGHT HAND)
SIX HOLE SINGLE CORNER CONNECTION (LEFT HAND)
FOUR HOLE DOUBLE CORNER CONNECTION
• Standard finishes: ZN, GRN • Wt./C 120 Lbs. (54.4 kg)
• Standard finishes: ZN, GRN • Wt./C 120 Lbs. (54.4 kg)
• Standard finishes: ZN, GRN • Wt./C 71 Lbs. (32.2 kg)
31/2”
(88.9)
(88.9)
Strut Fittings
31/2”
315/16”
315/16”
(100.0)
(100.0)
21/16”
15/8”
(52.4)
(41.3)
53/8” (136.5)
53/8”
31/2” (88.9)
(136.5)
Reference page 72 for general fitting and standard finish specifications.
94
Strut Systems
Wing Fittings B120
B121
B271
SIX HOLE DOUBLE CORNER CONNECTION
EIGHT HOLE DOUBLE CORNER CONNECTION
FIVE HOLE DOUBLE WING CONNECTION
• Standard finishes: ZN, GRN • Wt./C 110 Lbs. (49.9 kg)
• Standard finishes: ZN, GRN • Wt./C 152 Lbs. (68.9 kg)
• Standard finishes: ZN, GRN • Wt./C 95 Lbs. (43.1 kg)
57/16” (138.1)
31/2”
15/8”
315/16”
(41.3)
(88.9)
315/16”
21/16”
(100.0)
(52.4)
(100.0)
15/8” (41.3)
31/2”
53/8”
(88.9)
(136.5)
111/16” (42.8)
B272
B273
B122
EIGHT HOLE DOUBLE WING CONNECTION
TEN HOLE DOUBLE WING CONNECTION
SIX HOLE TRIPLE WING CONNECTION
• Standard finishes: ZN, GRN • Wt./C 156 Lbs. (70.7 kg)
• Standard finishes: ZN, GRN • Wt./C 185 Lbs. (83.9 kg)
• Standard finishes: ZN, GRN • Wt./C 110 Lbs. (49.9 kg)
57/16”
93/16”
(138.1)
(233.4)
57/16” (138.1)
315/16” 315/16”
(100.0)
15/8”
31/2”
21/16”
(100.0)
(52.4)
(88.9)
15/8” 111/16”
111/16”
111/16”
(42.8)
(42.8)
(42.8)
(41.3)
B123
B124
B276
TWELVE HOLE TRIPLE WING CONNECTION
NINE HOLE TRIPLE WING CONNECTION
FOURTEEN HOLE DOUBLE CORNER GUSSETTED CONNECTION
• Standard finishes: ZN, GRN • Wt./C 234 Lbs. (106.1 kg)
• Standard finishes: ZN, GRN • Wt./C 177 Lbs. (80.3 kg)
• Standard finishes: ZN, GRN • Wt./C 196 Lbs. (88.9 kg)
57/16”
93/16”
(138.1)
(233.4)
31/2” (88.9)
315/16”
315/16”
(100.0)
15/8”
(100.0)
(41.3)
111/16” (42.8)
111/16”
4” (101.6)
(42.8)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
95
Strut Fittings
4” (101.6)
Wing Fittings B274R
B274L
B495
EIGHT HOLE SINGLE CORNER GUSSETTED CONNECTION (RIGHT HAND)
EIGHT HOLE SINGLE CORNER GUSSETTED CONNECTION (LEFT HAND)
TEN HOLE DOUBLE WING GUSSETTED CONNECTION
• Standard finishes: ZN, GRN • Wt./C 176 Lbs. (79.8 kg)
• Standard finishes: ZN, GRN • Wt./C 176 Lbs. (79.8 kg)
• Standard finishes: ZN, GRN • Wt./C 240 Lbs. (108.8 kg)
93/16”
511/16”
521/32”
(144.5)
(233.4)
(143.7)
315/16” (100.0)
31/2”
37/8”
315/16” (100.0)
(88.9)
(88.9)
(88.9)
111/16”
111/16”
(42.8)
(42.8)
(98.4)
31/2”
31/2”
111/16” (42.8)
B277
B362
B571
TWELVE HOLE TRIPLE WING GUSSETTED CONNECTION
EIGHT HOLE DOUBLE CORNER GUSSETTED CONNECTION
EIGHT HOLE WING CONNECTION
• Standard finishes: ZN, GRN • Wt./C 285 Lbs. (129.3 kg)
• Standard finishes: ZN, GRN • Wt./C 226 Lbs. (102.5 kg)
• Standard finishes: ZN, GRN • Wt./C 201 Lbs. (91.2 kg)
93/16” (233.4)
53/8” (136.5) 4” (101.6)
315/16” 31/2”
315/16”
(100.0)
(100.0)
31/2”
(88.9)
(88.9)
15/8”
111/16”
(41.3)
(42.8)
4” (101.6)
B346R
EIGHT HOLE DOUBLE CORNER GUSSETTED CONNECTION (LEFT HAND)
EIGHT HOLE DOUBLE CORNER GUSSETTED CONNECTION (RIGHT HAND)
• Standard finishes: ZN, GRN • Wt./C 242 Lbs. (109.8 kg)
• Standard finishes: ZN, GRN • Wt./C 242 Lbs. (109.8 kg)
Strut Fittings
B346L
53/8” (136.5)
31/2”
31/2”
53/8” (136.5)
(88.9)
(88.9)
Reference page 72 for general fitting and standard finish specifications.
96
Strut Systems
Post Bases B279
B279SQ
B279FL
POST BASE FOR B22
POST BASE FOR B22
POST BASE FOR B22
• Standard finishes: ZN, GRN • Wt./C 314 Lbs. (142.4 kg)
• Standard finishes: ZN, GRN • Wt./C 314 Lbs. (142.4 kg)
• Standard finishes: ZN, GRN • Wt./C 230 Lbs. (104.3 kg) 3/4” (19.0) Dia .2 Holes
111/16” (42.8)
3/4” (19.0) Dia .4 Holes
111/16” (42.8)
6”
111/16”
3/4” (19.0) Dia .4 Holes
(42.8)
15/8”
15/8”
(41.3)
15/8”
(41.3)
(152.4)
41/4” 6”
41/4” (107.9)
(107.9)
(152.4)
6”
61/4”
8” (203.2)
(158.7)
3”
6”
(152.4)
(76.2)
(152.4)
3”
(41.3)
(76.2)
B280
B280SQ
POST BASE FOR B22
POST BASE FOR B22
B280FL POST BASE FOR B22
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 392 Lbs. (177.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4, AL • Wt./C 392 Lbs. (177.8 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 312 Lbs. (141.5 kg)
111/16” 3/4” (19.0) Dia .4 Holes
(42.8)
3/4” (19.0) Dia .2 Holes
3/4” (19.0) Dia .4 Holes
31/2”
(42.8)
31/2”
(88.9)
6”
111/16”
(42.8)
111/16”
(88.9)
31/2”
(152.4)
61/4”
41/4” 6”
6”
(107.9)
(107.9)
(152.4)
(152.4)
8”
41/4”
3”
(88.9)
(158.7)
(203.2)
6”
3”
(152.4)
(76.2)
(76.2)
B281A
B281ASQ
B281AFL
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
• Standard finishes: ZN, GRN • Wt./C 330 Lbs. (149.7 kg)
• Standard finishes: ZN, GRN • Wt./C 330 Lbs. (149.7 kg)
• Standard finishes: ZN, GRN • Wt./C 250 Lbs. (113.4 kg)
3/4” (19.0) Dia .4 Holes
35/16” 35/16”
(41.3)
(84.1)
3/4” (19.0) Dia .4 Holes
35/16” (84.1)
15/8” (41.3)
6” 41/4”
(152.4)
6”
(107.9)
41/4” (107.9)
(152.4)
8” 6”
(41.3)
(203.2)
3” (76.2)
3” (76.2)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
15/8”
(158.7)
(152.4)
6” (152.4)
61/4”
97
Strut Fittings
15/8”
3/4” (19.0) Dia .2 Holes
Post Bases B281
B281SQ
B281FL
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
POST BASE FOR B22A, B, C, ETC.
• Standard finishes: ZN, GRN, HDG • Wt./C 400 Lbs. (181.4 kg)
• Standard finishes: ZN, GRN, HDG, SS4 • Wt./C 400 Lbs. (181.4 kg)
• Standard finishes: ZN, GRN • Wt./C 320 Lbs. (145.1 kg)
3/4” (19.0)
35/16”
Dia. 4 Holes
35/16” 31/2”
(84.1)
(88.9)
(84.1) 3/4” (19.0)
3/4” (19.0)
Dia. 4 Holes
Dia. 2 Holes
35/16” (84.1)
31/2” (88.9)
6”
31/2”
(152.4)
6” (152.4)
41/4” 41/4”
(107.9)
8”
(107.9)
6”
6”
(88.9)
61/4” (158.7)
(203.2)
(152.4)
(152.4)
3”
3”
(76.2)
(76.2)
B281M
B281MSQ
B570
POST BASE FOR B22-2PL
POST BASE FOR B22-2PL
• Standard finishes: ZN, GRN • Wt./C 470 Lbs. (213.2 kg)
• Standard finishes: ZN, GRN • Wt./C 470 Lbs. (213.2 kg)
POST BASE FOR FOUR CHANNEL COMBINATIONS • Standard finishes: ZN, GRN • Wt./C 397 Lbs. (180.1 kg)
39/16” (90.5) 3/4” (19.0)
111/16”
Dia. 4 Holes
(42.8) 3/4” (19.0)
(41.3)
(88.9)
Dia. 4 Holes
31/2”
315/32”
(88.9)
6”
(87.9)
6”
6”
(152.4)
(152.4)
1/4”
6”
(6.3)
41/4” (107.9)
41/4” (107.9) 6” (152.4)
3”
(152.4)
(152.4)
6”
3”
(152.4)
3/4” (19.0)
(76.2)
Dia. 4 Holes
(76.2)
B570A
B278
POST BASE FOR FOUR POST BASE FOR B22 CHANNEL COMBINATIONS • Standard finishes: ZN, GRN • Standard finishes: ZN, GRN • Wt./C 550 Lbs. (249.5 kg)
Strut Fittings
15/8”
31/2”
31/2” (88.9)
• Wt./C 288 Lbs. (130.6 kg)
7/16”
(11.1) Dia. 4 Holes
B300
B585 POST BASE FOR B22A
POST BASE
• Standard finishes: ZN, GRN • Wt./C 97 Lbs. (44.0 kg)
• Material: Malleable Iron • Standard finishes: ZN, GRN • Wt./C 259 Lbs. (117.5 kg)
4”
15/8”
(101.6)
(41.3)
13/4”
31/2”
1/4”
3/4” (19.0)
(44.4)
(88.9)
(6.3)
(76.2)
(152.4)
5” (127.0)
6” 3”
3/4” (19.0)
Dia. 4 Holes
Countersunk To 3/4” (19.0) Dia. 9/16”
6” (152.4)
3/8” (9.5)
5”
15/8”
(127.0)
(41.3)
31/2”
31/16” (77.8)
7” (177.8)
(14.4)
21/16” (52.4)
(88.9)
Reference page 72 for general fitting and standard finish specifications.
98
Strut Systems
Brackets B187 BRACKET
B188 BRACKET
• Uniform Loading 1450 Lbs. (6.45 kN) • Safety Factor of 2.5 • Hole Spacing on Bracket Top 55/16” (150.8) Center to Center • Standard finishes: ZN, GRN • Wt./C 193 Lbs. (87.5 kg)
• Uniform Loading 1080 Lbs. (4.80 kN) • Safety Factor of 2.5 • Hole Spacing on Bracket Top 815/16” (227.0) Center to Center • Standard finishes: ZN, GRN • Wt./C 241 Lbs. (109.3 kg)
21/4”
11/16”
11/16”
(57.1)
(27.0)
21/4”
(27.0)
(57.1)
4”
9”
(101.6)
(228.6)
4” (101.6)
12” (304.8)
B189 BRACKET
B541 BRACKET
• Uniform Loading 870 Lbs. (3.87 kN) • Safety Factor of 2.5 • Hole Spacing on Bracket Top 1115/16” (303.2) Center to Center • Standard finishes: ZN, GRN • Wt./C 308 Lbs. (139.7 kg)
• • • • •
11/16” (27.0)
Uniform Loading 1240 Lbs. (5.51 kN) Safety Factor of 2.5 Hole Spacing on Bracket Top 77/16” (188.9) Center to Center Standard finishes: ZN, GRN Wt./C 201 Lbs. (91.2 kg)
21/4”
11/16”
21/4”
(57.1)
(27.0)
(57.1)
4”
4”
(101.6)
(101.6)
15”
101/2” (266.7)
(381.0)
B190 12” (304.8) BRACKET
B191-18 18” (457.2) BRACKET
• • • •
• • • •
Uniform Loading 900 Lbs. (4.00 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 260 Lbs. (117.9 kg)
11/16”
11/16” (27.0)
(101.6)
(27.0) 9/16”
x 3”
Slot (14.3) (76.2)
4” (101.6)
12”
18”
(304.8)
(457.2)
71/2” (190.5)
71/2” (190.5)
2”
9/16”
x 3” Slot (14.3) (76.2)
(50.8)
2” (50.8)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
99
Strut Fittings
4”
Uniform Loading 600 Lbs. (2.67 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 377 Lbs. (171.0 kg)
Brackets B191-24 24” (609.6) BRACKET • • • •
11/16” (27.0)
B192 24” (609.6) BRACKET
11/16”
Uniform Loading 450 Lbs. (2.00 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 377 Lbs. (171.0 kg)
• • • •
(27.0)
Uniform Loading 820 Lbs. (3.65 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 576 Lbs. (261.3 kg)
4” (101.6)
6” (152.4)
24”
24”
(609.6)
(609.6)
12” 27/16”
71/2”
(61.9)
(190.5) 9/16”
(304.8) 9/16”
x 3” Slot (14.3) (76.2)
x 3”
Slot (14.3) (76.2)
2”
2”
(50.8)
(50.8)
B290 161/2” (419.1) BRACKET
B289-12 121/2” (317.5) BRACKET
• • • •
• • • •
Uniform Loading 1200 Lbs. (5.34 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 405 Lbs. (183.7 kg)
Uniform Loading 1040 Lbs. (4.63 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 285 Lbs. (129.3 kg)
13/16”
13/16”
13/16”
(30.1)
(30.1)
(30.1)
13/16” (30.1)
6”
51/4”
(152.4)
(133.3)
6”
161/2”
31/8”
(152.4)
31/4”
121/2”
(82.5)
(317.5)
(419.1)
31/8” (79.4)
33/4”
(79.4)
(95.2)
53/4” (146.0)
21/2”
13/16”
21/2”
(63.5)
(30.1)
(63.5)
13/16” (30.1)
B289-14 141/2” (368.3) BRACKET
B291 181/2” (469.9) BRACKET
• • • •
• • • •
Uniform Loading 900 Lbs. (4.00 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 295 Lbs. (133.8 kg)
13/16”
13/16” (30.1)
Uniform Loading 1070 Lbs. (4.76 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN Wt./C 468 Lbs. (212.3 kg) (30.1)
13/16”
(30.1)
Strut Fittings
(30.1)
31/4” 6” (152.4)
13/16”
(82.5)
31/8” (79.4)
141/2”
6”
51/4”
(152.4)
(133.3)
(368.3)
31/8” 181/2” (79.4)
53/4”
73/4” (196.8)
(146.0)
21/2” (63.5)
(469.9)
21/2” (63.5)
13/16” (30.1)
13/16” (30.1)
Reference page 72 for general fitting and standard finish specifications.
100
Strut Systems
Brackets 13/16”
B292 201/2” (520.7) BRACKET
B297
• • • •
DOUBLE CHANNEL BRACKET
Uniform Loading 600 Lbs. (2.67 kN) Safety Factor of 2.5 Standard finishes: ZN, GRN, HDG, SS4 Wt./C 490 Lbs. (222.2 kg) (30.1)
61/4” (158.7)
• Safety Factor of 2.5 • Standard finishes: ZN, GRN, HDG
13/16”
2” (50.8) 3/8”
(20.6)
(9.5)
A
13/16” (30.1)
6”
45/8” (117.5)
71/4” (184.1)
(152.4)
31/8” (79.4)
201/2”
Part No. B297-12 B297-18 B297-24 B297-30 B297-36 B297-42
(520.7)
73/4” (196.8)
21/2” (63.5)
13/16” (30.1)
B409 SINGLE CHANNEL BRACKET
13/16”
• Safety Factor of 2.5 • Standard finishes: ZN, GRN, SS4
Uniform Load A 12” 18” 24” 30” 36” 42”
(304.8) (457.2) (609.6) (762.0) (914.4) (1066.8)
13/16”
(20.6)
kN
Lbs.
kg
1660 1100 835 665 550 465
(7.37) (4.88) (3.71) (2.95) (2.44) (2.06)
485 668 857 1040 1240 1440
(220.0) (303.0) (388.7) (471.7) (562.4) (653.2)
11/2”
B494
(38.1)
BRACED SINGLE BRACKET
H 2”
15/8”
(50.8)
Wt./C
Lbs.
(20.6)
45/8” (117.5)
B22A
L
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
(41.3)
4”
A
(101.6) Inside Brace on B494-24 and Larger.
3” B22
(76.2)
Part No. B409-6 B409-9 B409-12 B409-14 B409-16 B409-18 B409-24
Uniform Load A 6” 9” 12” 14” 16” 18” 24”
Lbs.
1920 1280 960 800
(152.4) (228.6) (304.8) (355.6) (406.4) (457.2) (609.6)
730
640 480
kN (8.54) (5.69) (4.27) (3.56) (3.25) (2.84) (2.13)
152 195 232 274 314
347 450
B174SH-B186SH L&R SLOTTED BRACKET • • • •
Safety Factor of 2.5 Specify L for left or R for right bracing Material: ASTM A1011 33,000 PSI min. yield Standard finishes: ZN, GRN
2” (50.8)
A B 2”
1”
(50.8)
(25.4)
Mounting Hole 7/16” (11.1) Dia.
13/32” x 1” Slot (10.3) (25.4)
kg (68.9) (88.4) (105.2) (124.3) (142.4) (157.4) (204.1)
Part No. B174SH B175SH B176SH B177SH B178SH B179SH B180SH B181SH B182SH B183SH B184SH B185SH B186SH
Uniform Load L
H
12” (304.8) 18” (475.2) 24” (609.6) 30” (762.0) 36” (914.4) 42” (1066.8) 48” (1219.2)
83/4” 83/4” 83/4” 111/4” 111/4” 16” 16”
Lbs.
(222.2) 1580 (222.2) 1000 (222.2) 996 (285.7) 924 (285.7) 864 (406.4) 580 (406.4) 500
24” 26” 28” 30” 12” 14” 16” 18” 20” 22” 6” 8” 10”
(609.6) (660.4) (711.2) (762.0) (304.8) (355.6) (406.4) (457.2) (508.0) (558.8) (152.4) (203.2) (254.0)
B 67/16” 615/16” 77/16” 715/16” 37/16” 315/16” 47/16” 415/16” 57/16” 515/16” 115/16” 27/16” 215/16”
(163.5) (176.2) (188.9) (201.6) (87.3) (100.0) (112.7) (125.4) (138.1) (150.8) (49.2) (61.9) (74.6)
kg (165.1) (217.3) (324.8) (420.5) (496.7) (635.0) (684.9)
Wt./C
Lbs.
kN
Lbs.
kg
225 225 225 225 350 350 250 250 250 250 225 225 325
(1.00) (1.00) (1.00) (1.00) (1.55) (1.55) (1.11) (1.11) (1.11) (1.11) (1.00) (1.00) (1.44)
370 425 480 520 143 162 204 232 275 317 58 82 103
(167.8) (192.8) (217.7) (235.9) (64.8) (73.5) (92.5) (105.2) (124.7) (143.8) (26.3) (37.2) (46.7)
Right bracket shown, left bracket gussett on opposite side.
101
Wt. /C Lbs.
(7.02) 364 (4.45) 479 (4.43) 716 (4.11) 927 (3.84) 1095 (2.58) 1400 (2.22) 1510
Uniform Load A
Reference page 72 for general fitting and standard finish specifications. Strut Systems
kN
Strut Fittings
9/32” (7.1) Dia. Holes
Part No. B494-12 B494-18 B494-24 B494-30 B494-36 B494-42 B494-48
Wt./C Lbs.
B42
Brackets B196
B198
13/16”
CHANNEL CLEVIS BRACKET
CHANNEL CLEVIS BRACKET
(20.6)
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
• Safety Factor of 2.5 53/8” • Standard finishes: (136.5) ZN, GRN
13/16” (20.6)
31/2” (88.9)
A 35/8”
A
(92.1)
B22 Uniform Load
B22
Part No.
A
(A)
Lbs.
kN
Lbs.
kg
B196-18 B196-24
18” 24”
(457.2)
600 450
(2.67)
430 510
(195.0)
(609.6)
(2.00)
Wt./C
(231.3)
Part No.
A
(A)
Uniform Load Lbs.
kN
Lbs.
kg
B198-6 B198-12
6” 12”
(152.4)
1600 800
(7.12)
185 284
(128.8)
(304.8)
B293
CHANNEL CLEVIS BRACKET
CHANNEL BRACKET
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
• Safety Factor of 2.5 • Standard finishes: ZN, GRN
(20.6)
(83.9)
13/16”
B198A 13/16”
(3.56)
Wt./C
(20.6)
31/2”
11/2”
(88.9)
(38.1)
31/2”
A
(88.9)
A B22 B22 Part No.
Uniform Load A
B198A-6 6” B198A-12 12”
Wt./C
(A)
Lbs.
kN
Lbs.
kg
(152.4)
1600 800
(7.12)
185 284
(83.9)
(304.8)
B293A CHANNEL BRACKET • Safety Factor of 2.5 • Standard finishes: ZN, GRN
(3.56)
(128.8)
(20.6)
11/2”
31/2”
(38.1)
Strut Fittings
A
Uniform Load
B293A-6 6” B293A-12 12” B293A-18 18” B293A-24 24”
kN
Lbs.
(152.4)
1200 600 400 300
(5.34)
144 252 340 412
(609.6)
Lbs.
kN
Lbs.
B293-6 B293-12 B293-18 B293-24
6” 12” 18” 24”
(152.4)
1200 600 400 300
(5.34)
144 252 340 412
(304.8) (457.2) (609.6)
(2.67) (1.78) (1.33)
Wt./C kg (65.3) (114.3) (154.2) (186.9)
(2.67) (1.78) (1.33)
B22
Wt./C
Lbs.
(457.2)
Uniform Load
63/8” (161.9)
(A) (304.8)
(A)
• Safety Factor of 2.5 • 6300 In.-Lbs (712 N•m) applies to fitting only, not to strength of strut arm • Refer to page 223 for strut 13/32” loading data (27.8) • Standard finishes: ZN, GRN • Wt./C 210 Lbs. (95.2 kg)
B22
A
A
B194 BRACKET FOR B22 & B24
13/16”
(88.9)
Part No.
Part No.
kg (65.3)
23/16”
(114.3)
(55.6)
(154.2)
B22
33/4”
(186.9)
(95.3)
Reference page 72 for general fitting and standard finish specifications.
102
Strut Systems
Brackets B370
B195
BRACKET FOR B22A & B11
• Safety Factor of 2.5 13/32” • 13000 In.-Lbs (1469 N•m) applies (27.8) to fitting only, not to strength of strut arm • Refer to page 217 for strut loading data • Standard finishes: ZN, GRN • Wt./C 266 Lbs. (120.6 kg) 8”
B22
BRACKET FOR B42
• Safety Factor of 2.5 • 2500 In.-Lbs (282 N•m) applies to fitting only, not to strength of strut arm 21/8” • Refer to page 217 for strut (54.0) loading data • Standard finishes: ZN, GRN • Wt./C 174 Lbs. (78.9 kg)
B22
37/8”
(203.2)
(98.4)
315/16” (100.0)
B22A
B42
33/4”
33/4”
(95.2)
(95.2)
B440
B449-4, 8 & 12
BRACKET FOR B52 & B54
CABLE SADDLE BRACKET
• Safety Factor of 2.5 • 2000 In.-Lbs (226 N•m) applies to fitting only, not to strength of strut arm • Refer to page 217 for strut loading data • Standard finishes: ZN, GRN B22 21/8” • Wt./C 177 Lbs. (80.3 kg)
13/16” (20.6)
• Safety Factor of 2.5 • Material: 11 Gauge (3.0) B ASTM A1011 HSLAS Gr. 50 • Standard finishes: ZN, GRN
(54.0)
A
37/8” (98.4)
2” (50.8)
B52
Part Uniform Load Wt./C Lbs. kN Lbs. kg No. A B 1 3 B449-4 4 /2” (114.3) 2 /8” (60.3) 2400 (10.67) 74 (33.5) B449-8 81/2” (215.9) 23/8” (60.3) 1270 (5.65) 124 (56.2) B449-12 121/2” (317.5) 4” (101.6) 860 (3.82) 184 (83.4)
33/4” (95.2)
B449-18 18” (457.2) CABLE SADDLE BRACKET • • • • •
Safety Factor of 2.5 Uniform Load 960 Lbs. (4.17 kN) Material: 11 Gauge (3.0) ASTM A1011 HSLAS Gr. 50 Standard finishes: ZN, GRN Wt./C 312 Lbs. (141.5 kg)
B293PL BRACKET PLATE ONLY • Standard finishes: ZN, GRN • Wt./C 46 Lbs. (20.8 kg)
13/16”
2” (50.8)
11/2”
4”
(38.1)
(101.6)
31/2” 18”
120°
(88.9)
13/16”
(457.2)
(20.6)
11/4” (31.7)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
103
Strut Fittings
(20.6)
Brackets B816
B852S-W-D
• Standard finishes: ZN, HDG
• Specify W = 8, 12, 16 • Specify D = 6, 8, 10, 12, 16, 18, 24 • 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band • Standard finishes: ZN, HDG
2”
13/32” (10.3) Dia.
(50.8)
61/2” (165.1)
13/16” (20.6) Dia.
23/8” (60.3)
21/8” (54.0) 9/16” (355.6)
(355.6)
725/32”
(14.3)
14” 14”
(197.6)
9/16” x 29/16” Slot
(14.3)
(65.1)
W D
11/16” x 1” Slot (17.4) (25.4)
13/16” x 1” Slot (20.6) (25.4)
B802D-W
B810-W
• Specify W = 8, 12, 16 • Standard finishes: ZN, HDG
• Specify W = 8, 12, 16 • 13/16” (20.6mm) x 1” (25.6mm) banding slots for steel band • Standard finishes: ZN, HDG
13/16” (20.6) Dia.
13/32” (10.3) Dia.
Strut Fittings
13/16” (20.6) Dia.
95/8” (244.5) W
725/32” (197.6)
W
13/16” x 1” Slot (20.6) (25.4)
Reference page 72 for general fitting and standard finish specifications.
104
Strut Systems
Brackets B811-W
B812-*
• Can be attached directly to B809 & B812 • Specify W = 8, 12, 16 • Standard finishes: ZN, HDG
• Specify D = 6, 8, 10, 12, 16, 18, 24 • 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band • Standard finishes: ZN, HDG
121/32” (42.1) 13/32” (10.3) Dia. 13/16” (20.6) Dia.
W
27/16”
725/32”
(61.9)
(197.6) 13/16” x 1” Slot (20.6) (25.4)
D 13/16” (20.6)
B809B-* • Specify D = 6, 8, 10, 12, 16, 18, 24 • 13/16” (20.6mm) x 1” (25.4mm) banding slots for steel band • Standard finishes: ZN, HDG
13/32” (10.3) Dia. 13/16” (20.6) Dia.
D
Part No.
D
H
725/32”
mm
In.
mm
B809B-6
6”
(152.4)
123/4”
(323.9)
B809B-8
8”
(203.2)
143/4”
(374.7) (425.5)
B809B-10
10”
(254.0)
163/4”
B809B-12
12”
(304.8)
183/4”
(476.2) (577.8) (628.6)
B809B-16
16”
(406.4)
223/4”
B809B-18 B809B-24
18” 24”
(457.2)
243/4” 273/4”
(609.6)
(197.6) 13/16” x 1” Slot (20.6) (25.4)
H
(704.8)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
105
Strut Fittings
In.
Miscellaneous Fittings B214 R&L
B514 R&L
REEL RACK SUPPORT FOR 11/4” (32) PIPE
REEL RACK SUPPORT FOR 2” (50) PIPE • Standard finishes: ZN, GRN • Wt./C 246 Lbs. (111.6 kg)
• Standard finishes: ZN, GRN • Wt./C 200 Lbs. (90.7 kg)
3”
3”
(76.2)
(76.2)
53/8” (136.5)
53/8” (136.5)
35/8”
(92.1)
(92.1)
53/8” (136.5)
A
B214R Right Hand
35/8”
B214L Left Hand
53/8” (136.5)
B514R Right Hand
B514L Left Hand
B475
B473
DOUBLE REEL RACK SUPPORT ON SINGLE CHANNEL FOR 11/4” (32) PIPE
DOUBLE REEL RACK SUPPORT ON SINGLE CHANNEL FOR 2” (50) PIPE
• Standard finishes: ZN, GRN • Wt./C 326 Lbs. (147.9 kg)
• Standard finishes: ZN, GRN • Wt./C 351 Lbs. (159.2 kg)
3”
3” (76.2)
(76.2)
9”
9”
(228.6)
(228.6)
B474
B472
DOUBLE REEL RACK CHANNEL FOR 11/4” (32) PIPE
DOUBLE REEL RACK SUPPORT ON DOUBLE CHANNEL FOR 2” (50) PIPE
• Standard finishes: ZN, GRN • Wt./C 257 Lbs. (116.6 kg)
• Standard finishes: ZN, GRN • Wt./C 299 Lbs. (135.6 kg)
31/4”
31/4”
(82.5)
Strut Fittings
(82.5)
53/8” (136.5)
53/8” (136.5)
Reference page 72 for general fitting and standard finish specifications.
106
Strut Systems
Miscellaneous Fittings B438
B439
PIPE SUPPORT BRACKET
PIPE SUPPORT BRACKET
• Standard finishes: ZN, GRN • Material: ASTM A36 • Wt./C 132 Lbs. (59.9 kg)
• Standard finishes: ZN, GRN • Wt./C 88 Lbs. (39.9 kg)
41/4” (107.9)
31/2” (88.9)
3/8”
4”
(9.5)
1/4”
4”
(101.6)
(6.3)
(101.6)
B411 SERIES
B381-B385
LADDER RUNGS
WALL LADDER BRACKETS
• Standard finishes: ZN, GRN
• Standard finishes: ZN, GRN
13/16” (20.6)
C
B 2”
A
I.D. (50.8)
13/16” (20.6)
A 13/16” (20.6)
Part No. B381 B382 B383 B384 B385
Wt./C Part No.
A
B411-12 12” B411-15 15” B411-18 18”
(A)
Lbs.
kg
(304.8)
176 202 234
(79.8)
(381.0) (457.2)
(91.6) (106.1)
Wt./C A 23/8” 43/8” 63/8” 83/8” 103/8”
(A) (60.3) (111.1) (161.9) (212.7) (263.5)
B 6” 8” 10” 12” 14”
(B) (152.4) (203.2) (254.0) (304.8) (355.6)
C 75/8” 95/8” 115/8” 135/8” 155/8”
(C) (193.7) (244.5) (295.3) (346.1) (396.9)
Lbs.
kg
110 (49.9) 164 (74.4) 200 (90.7) 253 (114.7) 318 (144.2)
B587-1/2, 3/4 & 1 PIPE COUPLING FITTING • Safety Factor of 2.5 • Standard finishes: ZN, GRN
Design Load
(68.2)
Part No. B587-1/2 B587-3/4 B587-1
For Pipe Size 1/2”
(15)
3/4”
(20)
1”
(25)
Strut Fittings
53/8” (136.5)
211/16”
Wt./C Lbs.
77 84 105
kg
Design Load Lbs.
kN
1000 (4.45) (38.1) 1400 (6.23) (47.6) 1900 (8.45) (34.9)
Reference page 72 for general fitting and standard finish specifications. Strut Systems
107
Miscellaneous Fittings B349
B350
TROLLEY BEAM SUPPORT
TROLLEY BEAM JOINT SUPPORT
• Design Load 1200 Lbs. (5.34 kN) • Safety Factor of 2.5 • Use 3/8” x 3” bolts in side hole to clamp strut together (not included) • Standard finishes: ZN, GRN 9/16”(14.3) Dia. • Wt./C 107 Lbs. (48.5 kg)
• Design Load 1200 Lbs. (5.34 kN) • Use 3/8” x 3” bolts in side hole to clamp 21/8” (54.0) strut together (not included) • Standard finishes: ZN, GRN 9 /16”(14.3) Dia. • Wt./C 233 Lbs. (105.7 kg)
21/8” (54.0)
1 Hole
315/16”
1 Hole
(100.0)
7/16”(11.1) Dia. 6 Holes
11/32”
2 Holes
(26.2)
(26.2)
13/32”
15/8” (41.3)
121/32”
121/32” (42.0)
(42.0)
B614
COLUMN SUPPORT FOR B22 • Quick installation (one bolt to tighten) • Design Load 800 Lbs. (3.56 kN) Slip with Safety Factor of 3 • Use with B22 and B24 Channel • Sold in pairs • Standard finish: ZN • Wt./C 50 Lbs. (22.6 kg)
(100.0)
(88.9)
7/16”(11.1) Dia.
11/32”
315/16”
31/2”
21/32” (27.8) (16.7)
B613
B613A
COLUMN SUPPORT FOR B22
COLUMN SUPPORT FOR B52
• Design Load 800 Lbs. (3.56 kN) Slip with Safety Factor of 3 • Use with B22 and B24 Channel • Setscrews to be torqued to 19 ft./Lbs • Sold in pairs • Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
• Design Load 800 Lbs. (3.56 kN) Slip with Safety Factor of 3 • Use with B52 and B54 Channel • Setscrews to be torqued to 19 ft./Lbs • Sold in pairs • Standard finishes: ZN, GRN, HDG • Wt./C 100 Lbs. (45.3 kg)
15/8”
15/8”
(41.3)
(41.3)
31/2”
31/2”
(88.9) 3/8” x 2” Cone
3/8” x 2” Cone
Point Setscrews
Point Setscrews
B560
B562
45° STAIR SUPPORT
37-1/2° STAIR SUPPORT
• Standard finishes: ZN, GRN • Wt./C 220 Lbs. (99.8 kg)
• Standard finishes: ZN, GRN • Wt./C 206 Lbs. (93.4 kg)
87/8” (225.4)
87/8” (225.4)
Strut Fittings
(88.9)
31/2” 31/2”
(88.9)
11/16” 31/2”
17/8”
(88.9) 13/16”
31/2”
(27.0) 45°
13/16”
(47.6)
(88.9)
11/16” (27.0)
17/8”
(88.9) 371/2°
(47.6)
(20.6)
(20.6)
33/4”
33/4”
(95.2)
(95.2)
Reference page 72 for general fitting and standard finish specifications.
108
Strut Systems
Miscellaneous Fittings B376
35/16”
FOUR BEARING TROLLEY ASSEMBLY
B377
15/16”
(84.1)
TWO BEARING TROLLEY ASSEMBLY
(33.3)
• Safety Factor of 2.5 • Stainless steel ball bearings • Not for continuous cycling applications • Standard finishes: ZN 33/8” • Wt./C 110 Lbs. (49.9 kg) (85.7)
11/8” (28.6) Bearing O.D. 13/16” (20.6)
• Safety Factor of 2.5 • Stainless steel ball bearings • Not for continuous cycling applications • Standard finishes: ZN • Wt./C 48 Lbs. (21.8 kg)
15/16”
3”
(23.8)
(76.2)
Lbs.
kN
RPM
300 450 600
(1.33)
@600 @300 @100
Design Load
Lbs.
kN
RPM
150 225 437
(.67)
@600 @300 @100
(1.00) (1.94)
B477
33/8”
13/16”
(85.7)
(20.6)
11/4” (31.7)
Design Load
FOUR BEARING LIGHT DUTY TROLLEY ASSEMBLY
• • • • •
Design Load 50 Lbs. (.22 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN • Wt./C 30 Lbs. (13.6 kg)
11/4” (31.7)
11/8”
13/4”
(28.6)
(44.4)
B477P
• • • • •
Design Load 100 Lbs. (.44 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN • Wt./C 68 Lbs. (30.8 kg)
B478P
WITH PLASTIC BEARINGS
11/32”
• Design Load 10 Lbs. (.045 kN)
5/8” (15.9)
9/32” (7.1)
Dia. Hole (19.0)
(28.6) Bearing O.D.
B478
TWO BEARING LIGHT DUTY TROLLEY ASSEMBLY
3/4”
11/8”
Design Load in B22
Design Load in B22
(2.67)
(33.3)
5/8” (15.9)
(2.00)
15/16”
(8.7)
WITH PLASTIC BEARINGS • Design Load 20 Lbs. (.090 kN)
9/32”
x 9/16”
(7.1)
(14.3)
(31.7)
(7.1) Dia. Hole
Slot-(2) 3/4” (19.0)
11/4”
9/32”
3” (76.2)
2” (50.8)
Design Load
Design Load
B478H
B477H
FOUR BEARING LIGHT DUTY TROLLEY ASSEMBLY WITH EYE HOOK
TWO BEARING LIGHT DUTY TROLLEY ASSEMBLY WITH EYE HOOK • • • • •
11/4” (31.7)
• • • • •
Design Load 100 Lbs. (.44 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN 11/8” • Wt./C 72 Lbs. (32.6 kg) (28.6)
B477HP
WITH PLASTIC BEARINGS • Design Load 10 Lbs. (.045 kN)
3/4” I.D (19.0)
B478HP
WITH PLASTIC BEARINGS
315/16” (100.0)
11/32”
1/4” (6.3) EYE ROD
• Design Load 20 Lbs. (.090 kN)
(8.7)
3/4” I.D (19.0)
Design Load
Design Load
Reference page 72 for general fitting and standard finish specifications. Strut Systems
1/4” (6.3) EYE ROD
109
Strut Fittings
Design Load 50 Lbs. (.22 kN) Safety Factor of 2.5 Stainless steel ball bearings Not for continuous cycling applications Material:12 Gauge (2.6) ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN • Wt./C 36 Lbs. (16.3 kg)
Miscellaneous Fittings B203-B206 & B220-B223
B283-B286
CHANNEL END CAPS TYPE X
A
• Material: ASTM A1011 CS Type B • Standard finishes: ZN, GRN, HDG, SS4, AL
Part No. B203 B204 B205 B206 B220 B221 B222 B223
CHANNEL END CAPS • Material: ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN, GRN
A
Wt./C Use With
A
(A)
Lbs.
kg
B42 B54 B22 B32 B52 B12 B11 B24
1.015 .827 1.640 1.390 .827 2.452 3.265 1.640
(25.8) (21.0) (41.6) (35.3) (21.0) (62.3) (82.9) (41.6)
6 5 10 8 4 15 20 10
(2.7) (2.2) (4.5) (3.6) (1.8) (6.8) (9.1) (4.5)
B Part No.
Use With
A
Wt./C
B283 B284 B285 B286
B52 B54 & B56 B22 B24 & B26
119/32” 119/32” 119/32” 119/32”
(A)
B
(B)
(40.5) 25/32” (19.8) (40.5) 25/32” (19.8) (40.5) 119/32” (40.5) (40.5) 119/32” (40.5)
B287 & B288
B3322, B3332, B3342, B3352
CHANNEL END CAPS
ANCHOR END CAPS TYPE Y
• Material: ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN, GRN
• Material: ASTM A1011 33,000 PSI min. yield • Standard finishes: ZN
Lbs.
kg
6 6 13 14
(2.7) (2.7) (5.9) (6.3)
3/8” (9.5)
119/32”
119/32”
(40.5)
(40.5)
Dia. Hole
25/8” (66.7)
A 113/16”
B
(46.0)
Part No.
Strut Fittings
B287 B288
Wt./C Use With
Lbs.
kg
B22 B24
13 14
(5.9) (6.3)
Part No.
Use With
A
Wt./C
B3322 B3332 B3342 B3352
B22I B32I B42I B52I
1.270 1.000 .645 .460
(A)
B
(32.2) 13/16” (25.4) 13/16” (16.4) 11/4” (11.7) 15/16”
(B)
Lbs.
kg
(30.2) (30.2) (31.8) (33.3)
15 15 15 15
(6.8) (6.8) (6.8) (6.8)
B822
B822A
B852
PLASTIC END CAP FOR B22 & B24
PLASTIC END CAP FOR B22A & B11
PLASTIC END CAP FOR B52
• Material: Soft White PVC • Wt./C 3 Lbs. (1.3 kg) • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
• Material: Soft White PVC • Wt./C 5 Lbs. (2.2 kg) • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
• Material: Soft White PVC • Wt./C 2.5 Lbs. (1.1 kg) • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
11/4” (31.7)
11/4”
11/4”
(31.7)
(31.7)
Reference page 72 for general fitting and standard finish specifications.
110
Strut Systems
Miscellaneous Fittings B823
B825
PROFILE END CAPS
PLASTIC END CAPS
• Material: PVC • Available in colors: White (W), Yellow (Y), Black (BLK), Gray (GRY), Green (GRN)
• Material: Polyurethane • Available in colors: Gray (GRY), Green (GRN)
Approx. 3/4” deep (19.0)
Part No.
Fits Channel Sizes
Wt./C
B823-22A B22A, B24A, B26A B823-22 B22, B24, B26 B823-42 B42 B823-52 B52, B54, B56
Lbs.
kg
6.9 4.1 3.8 3.5
(3.1) (1.8) (1.7) (1.6)
Fits Channel Sizes
Part No. B825-22 B825-52
B22 & B24 B52 & B54
B408SLBVNS Series
43/8”
STAND-OFF BRACKETS
(111.1)
• Material: 1/4” (6.3) • Standard Finishes: HDG, ZN, GRN • For pipe or rigid conduit sizes of 11/2” (32) and 2” (50) use with B501 Series ‘U’-Bolts • For strut channels 15/8” (41.3) wide use with B500 Series Square ‘U’-Bolts • Hardware is not included
Wt./C Lbs.
kg
2.0 1.0
(0.9) (0.4)
21/8” (53.5)
A
11/8” (28.6)
45/8”
15/16”
(117.5)
(33.3)
21/4”
1/2”
(57.1)
(12.7)
23/16” (55.6)
Part No. B408SLBVNS B408SLBVNS1 B408SLBVNS2
A In.
Wt./C (mm)
31/2” (88.9) 3” (76.2) 2” (50.8)
Lbs.
(27.0)
23/16”
kg
189 (85.7) 220 (99.8) 236 (107.0)
11/16”
(55.6)
(6) Slots 7/16” (11.1) x 11/8”
(28.6)
11/16”
21/4”
(27.0)
(57.1)
Strut Fittings
Reference page 72 for general fitting and standard finish specifications. Strut Systems
111
