HP iPAQ H2200 faceplate replacement
HP iPAQ H2200 faceplate replacement
HP iPAQ H2200 faceplate replacement Written By: Tyler Andrews
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 10
HP iPAQ H2200 faceplate replacement
INTRODUCTION The purpose of this guide is to instruct the reader on how to replace the faceplates of their HP iPAQ H2200 device.
TOOLS: Phillips #00 Screwdriver (1) T5 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 10
HP iPAQ H2200 faceplate replacement
Step 1 — Battery
Press and slide the battery cover tab to remove battery cover.
Step 2
Pull on the black tab to lift the battery out of the battery compartment.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 10
HP iPAQ H2200 faceplate replacement
Step 3 — Main Board
Remove the stylus by sliding it out of the slot.
Remove the CF card by sliding it out of the slot at the top of the device. (the black slot substitute).
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 10
HP iPAQ H2200 faceplate replacement
Step 5
Press down and push the black side strips toward the top of the device to remove them.
Step 6
Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 10
HP iPAQ H2200 faceplate replacement
Step 7
Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).
Step 8
© iFixit — CC BY-NC-SA
www.iFixit.com
Open the LCD connector, where the orange strip attaches to the main board.
Page 6 of 10
HP iPAQ H2200 faceplate replacement
Step 9
Carefully remove the orange LCD strip from the connector.
Unscrew the 2 screws located at each top corner of the main board.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 10
HP iPAQ H2200 faceplate replacement
Step 11
Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.
Unscrew the two bottom screws on LCD screen that were previously located under the main board.
Step 12 — LCD Screen
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 10
HP iPAQ H2200 faceplate replacement
Step 13
Press on side tabs to loosen and remove the LCD screen.
Step 14 — Faceplates
Remove the faceplate by unscrewing the green screw located on the top right of the front faceplate.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-01 11:50:37 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 10
HP iPAQ H2200 faceplate replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 10 of 10
HP iPAQ H2200 faceplate replacement Written By: Tyler Andrews
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 10
HP iPAQ H2200 faceplate replacement
INTRODUCTION The purpose of this guide is to instruct the reader on how to replace the faceplates of their HP iPAQ H2200 device.
TOOLS: Phillips #00 Screwdriver (1) T5 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 10
HP iPAQ H2200 faceplate replacement
Step 1 — Battery
Press and slide the battery cover tab to remove battery cover.
Step 2
Pull on the black tab to lift the battery out of the battery compartment.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 10
HP iPAQ H2200 faceplate replacement
Step 3 — Main Board
Remove the stylus by sliding it out of the slot.
Remove the CF card by sliding it out of the slot at the top of the device. (the black slot substitute).
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 10
HP iPAQ H2200 faceplate replacement
Step 5
Press down and push the black side strips toward the top of the device to remove them.
Step 6
Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 10
HP iPAQ H2200 faceplate replacement
Step 7
Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).
Step 8
© iFixit — CC BY-NC-SA
www.iFixit.com
Open the LCD connector, where the orange strip attaches to the main board.
Page 6 of 10
HP iPAQ H2200 faceplate replacement
Step 9
Carefully remove the orange LCD strip from the connector.
Unscrew the 2 screws located at each top corner of the main board.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 10
HP iPAQ H2200 faceplate replacement
Step 11
Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.
Unscrew the two bottom screws on LCD screen that were previously located under the main board.
Step 12 — LCD Screen
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 10
HP iPAQ H2200 faceplate replacement
Step 13
Press on side tabs to loosen and remove the LCD screen.
Step 14 — Faceplates
Remove the faceplate by unscrewing the green screw located on the top right of the front faceplate.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-01 11:50:37 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 10
HP iPAQ H2200 faceplate replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 10 of 10
