Induction Motors - Oriental Motor

Standard AC Motors Introduction

Standard AC Motors

Reversible Motors

Induction Motors

Induction Motors

Induction Motors

Constant Speed Motors

Electromagnetic Brake Motors V Series Clutch & Brake Motors Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors Torque Motors Right-Angle Gearheads Linear Heads Brake Pack

A-20 A-25 A-26 A-60 A-72

Installation

Features and Types of Induction Motors ·················· General Specifications ············································· World K Series [1 W∼90 W (1/750 HP∼1/8 HP)] ··· BH Series [200 W (1/4 HP)] ···································· 2-Pole, High-Speed Type [40 W∼150 W (1/19 HP∼1/5 HP)]

Accessories

Page

A-19

Standard AC Motors

Features and Types of Induction Motors ■ Features of Induction Motors

1 W, 3 W (1/750 HP, 1/250 HP)

● Optimal for Uni-Directional and Continuous Operation

● Extensive Lineup

Induction motors are optimal for uni-directional and continuous operation such as a conveyor system.

The World K Series and BH Series are available. We have models with an output power range of 1 W (1/750 HP) to 200 W (1/4 HP), so that you can find one that meets your specific application.

● Easy Operation

6W (1/125 HP)

All you need is to connect a capacitor and plug the motor into an AC power supply, and the motor can be easily operated. (No capacitor is needed for a three-phase motor.)

● Compatible with Various Gearheads Combination with a gearhead allows the motor to reduce to a required speed or generate higher torque.

15 W (1/50 HP)

●

RoHS-Compliant

The World K Series and BH Series conform to the RoHS Directive that prohibits the use of six chemical substances including lead and cadmium.

25 W (1/30 HP)

■ Types of Induction Motors

40 W (1/19 HP)

Series

World K Series

Features, Lineup

● Conforms to Safety Standards All World K Series models have a built-in overheat protection device and conform to major safety standards.

60 W (1/12 HP)

● Applicable Standards

90 W (1/8 HP)

UL/CSA Standards Certified under the China Compulsory Certification System✽ (CCC System) CE Marking (Low Voltage Directive) ✽ Except Conduit Box Type

● The Motor Bearing Life is Twice as Long as a Conventional Type A motor's life is determined by its bearing. We adopted high-performance bearing grease to lubricate this important component. As a result, the bearings of World K Series motors last twice as long as conventional bearings. [Excluding 1 W (1/750 HP) and 3 W (1/250 HP) type.]

● Protective Earth Terminal on the Motor

● Motor Overheat Protection Device Thermal protector, Impedance protected

200 W (1/4 HP)

● Global Voltage Specifications

2-Pole 40-150 W (1/19-1/5 HP)

The World K Series supports the power supply voltages used in major countries. Motors meeting the local voltage standard are readily available in major countries in Europe, Asia and North America.

Protective Earth Terminal

● Lineup Frame Size Output Power

Voltage

BH Series

● Smallest Frame Size among 200 W (1/4 HP) Motors These motors achieve a high output of 200 W (1/4 HP) with a frame size of 104 mm (4.09 in.).

● Hypoid Gear-Employed Right Angle Type is Available.

Frame Size Output Power

□104 mm (□4.09 in.) 200 W (1/4 HP)

Type

Cable Type: Right-Angle, Hollow Shaft Type, Right-Angle, Solid Shaft Type, Parallel Shaft Type, Round Shaft Type Terminal Box Type: Right-Angle, Hollow Shaft Type, Right-Angle, Solid Shaft Type, Parallel Shaft Type, Round Shaft Type

Voltage

Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC

With each combination type, the motor and gearhead come pre-assembled for easy installation into your equipment.

A-20

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC

● Lineup

● "Combination Type" for Easy Installation

● Conforms to Safety Standards and Global Voltage Specifications

□42 mm (□1.65 in.)∼□90 mm (□3.54 in.) Lead Wire Type: 1 W∼90 W (1/750 HP∼1/8 HP) Terminal Box Type: 25 W∼90 W (1/30 HP∼1/8 HP) Conduit Box Type: 25 W∼90 W (1/30 HP∼1/8 HP) 2-Pole, High-Speed Type: 40 W∼150 W (1/19 HP∼1/5 HP)

Standard AC Motors

■ Features of Gearheads ● Easy Speed Reduction and Torque Increase Combination with a gearhead allows the motor to reduce to a required speed or generate higher torque.

● Wide Variety of Products

Motor

●

RoHS-Compliant

Gearhead Pinion Shaft

● Combine gearheads with a pinion shaft type motor. ● Gearheads of World K Series are sold separately. BH Series comes with the gearhead pre-assembled.

Induction Motors

Gearheads conform to the RoHS Directive that prohibits the use of six chemical substances including lead and cadmium.

Reversible Motors

■ Types of Gearheads Types

Features

Electromagnetic Brake Motors

Long Life, Low Noise GN-S Gearhead

● Long Rated Life of 10000 Hours

30

[Measurement conditions] Load: 1.2 N•m Direction: Clockwise Measurement distance: 1 m (Measured in A-weighted sound pressure level)

15 10 5 0 25.0 40 63 100 160 250 400 630 1K 1.6K 2.5K 4K 6.3K 10K 16K 31.5 50 80 125 200 315 500 800 1.25K 2K 3.15K 5K 8K 12.5K 20K

Frequency [Hz]

● Long Rated Life of 10000 Hours

● Applicable Products

The GE-S gearhead achieves a long rated life of 10000 hours, twice the level of a conventional gearhead, by adopting a large, specially designed bearing and reinforced gears.

60 W (1/12 HP) or 90 W (1/8 HP) GE pinion motor

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

6 W (1/125 HP), 15 W (1/50 HP), 25 W (1/30 HP) or 40 W (1/19 HP) GN pinion motor

Sound Pressure Level [dB(A)]

● Applicable Products

20

■: Long Life, Low Noise GN-S Gearhead 4IK25GN-AW2J/4GN120S ■: GN-K Gearhead (Conventional Model) 4IK25GN-A/4GN120K

Clutch & Brake Motors

The GN-S gearhead generates less noise thanks to gears with a special shape and surface machining assembled with the use of advanced technology.

25

V Series

The GN-S gearhead achieves a long rated life of 10000 hours, twice the level of a conventional gearhead, by adopting a large, specially designed bearing and reinforced gears.

● Low Noise Design

Long Life GE-S Gearhead

Introduction

Gearheads come in various types including the long life, low noise gearhead and right-angle gearhead. Most gearheads are available with 20 different gear ratios from 3:1 to 180:1.

● The GE-S gearhead comes with a tapped hole at the tip of the shaft. Torque Motors

● Ideal Space-Saving Solution

● Applicable Products

➜ Page A-239

The gear shaft is positioned at right angles with the motor shaft, enabling space-saving.

25 W (1/30 HP), 40 W (1/19 HP), 60 W (1/12 HP) or 90 W (1/8 HP) pinion motor

● Solid shaft type of GE pinion gearhead comes with a tapped hole at the tip of the shaft.

Brake Pack

Select an appropriate type that suits your specific application.

Linear Heads

● Hollow Shaft and Solid Shaft Types are Available

Right-Angle Gearheads

Right-Angle Gearhead

Accessories Installation

A-21

Standard AC Motors

■ Product Line of Induction Motors Series

Voltage (VAC)

1 W, 3 W (1/750 HP, 1/250 HP)

Single-Phase 110/115 Single-Phase 220/230

World K Series

6W (1/125 HP)

Three-Phase 200/220/230

15 W (1/50 HP)

2-Pole, High-Speed Type

1 W, 3 W (1/750 HP, 1/250 HP)

6W (1/125 HP)

15 W (1/50 HP)

25 W (1/30 HP)

●

●

●

●

●

● ● ● ● ● ● ● ● ●

Lead Wire Terminal Box Conduit Box Lead Wire Terminal Box Conduit Box Lead Wire Terminal Box Conduit Box

● ●

40 W (1/19 HP)

60 W (1/12 HP)

□90 mm (□3.54 in.)

□104 mm (□4.09 in.)

40 W (1/19 HP)

60 W (1/12 HP)

90 W (1/8 HP)

● ● ● ● ● ● ● ● ●

● ● ● ● ● ● ● ● ●

● ● ● ● ● ● ● ● ●

150 W (1/5 HP)

Lead Wire

●

●

●

●

●

Single-Phase 220/230

Lead Wire

●

●

●

●

●

●

●

● ●

25 W (1/30 HP)

Single-Phase 110/115

40 W (1/19 HP)

Single-Phase 220/230 Three-Phase 200/220/230

Lead Wire Terminal Box Cable Terminal Box Cable Terminal Box

200 W (1/4 HP)

● ● ● ● ●

Terminal Box

60 W (1/12 HP)

■ Product Line of Gearheads Gearhead Type of Gearhead

90 W (1/8 HP) 200 W (1/4 HP)

Parallel Shaft

2-Pole 40-150 W (1/19-1/5 HP)

Applicable Motor Output Power

Type of Pinion

World K Series

6 W∼40 W (1/125 HP∼1/19 HP)

GN Type Pinion Shaft

World K Series

GE Type Pinion Shaft

Rated Life (hours)

Low Noise

GN Type Pinion Shaft

10000

●

1 W∼40 W (1/750 HP∼1/19 HP)

GN Type Pinion Shaft

5000

World K Series

60 W, 90 W (1/12 HP, 1/8 HP)

GE Type Pinion Shaft

10000

GN Type Pinion Shaft

World K Series

25 W, 40 W (1/30 HP, 1/19 HP)

GN Type Pinion Shaft

5000

GE Type Pinion Shaft

World K Series

60 W, 90 W (1/12 HP, 1/8 HP)

GE Type Pinion Shaft

5000

GN Type Pinion Shaft

World K Series

25 W, 40 W (1/30 HP, 1/19 HP)

GN Type Pinion Shaft

5000

GE Type Pinion Shaft

World K Series

60 W, 90 W (1/12 HP, 1/8 HP)

GE Type Pinion Shaft

5000

Type of Pinion

Series

Long Life, Low Noise GN-S Gearhead

GN Type Pinion Shaft

GN-K Gearhead

Long Life GE-S Gearhead

Hollow Shaft Gearhead Right-Angle Shaft Solid Shaft Gearhead

A-22

Motor Frame Size, Output Power □80 mm (□3.15 in.)

□60 mm □70 mm (□2.36 in.) (□2.76 in.)

Single-Phase 110/115

Three-Phase 200/220/230

BH Series

Type

□42 mm (□1.65 in.)

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Standard AC Motors

■ System Configuration Gearheads (Sold separately) Parallel Shaft Gearheads (➜ Page A-21)

Right-Angle Gearheads (➜ Page A-239) Hollow Shaft Type

Solid Shaft Type Introduction Induction Motors

Induction Motors

Reversible Motors

Peripheral Equipment (Sold separately)

Motor (Pinion Shaft)

Electromagnetic Brake Motors

①Brake Pack

SB50W AC Power Supply (Main power supply)

(➜ Page A-277)

V Series

Capacitor Cap (Included) ②Speed Controller

Clutch & Brake Motors

FE100/FE200

Capacitor (Included)

(➜ Page B-156)

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

Accessories (Sold separately)

③Mounting Brackets

④Flexible Couplings

(➜ Page A-288)

(➜ Page A-292)

Torque Motors

No.

Overview

Product Name Brake Pack Speed Controller Mounting Brackets Flexible Couplings

Use this brake pack to stop the motor instantaneously, perform bi-directional operation, and more. Combine this Speed Controller with a three-phase motor for easy speed control. Equipped with a digital display. Dedicated mounting bracket for the motor and gearhead. Clamp type coupling that connects the motor or gearhead shaft to the driven shaft.

Linear Heads

●Example of System Configuration (Sold separately)

(Sold separately)

Mounting Bracket Flexible Coupling SOL4U10

MCL30F06F06

●Gearheads cannot be combined with round shaft type motors.

Accessories

● The system configuration shown above is an example. Other combinations are available.

Brake Pack

Induction Motor Long Life, (Pinion shaft) Low Noise Gearhead 4IK25GN-AW2U 4GN25SA

Page A-277 B-156 A-288 A-292

Right-Angle Gearheads

① ② ③ ④

Installation

A-23

Standard AC Motors

■ Product Number Code ● World K Series

5 I K 40 GN - AW 2 T U ① ② ③

④

⑤

⑥

⑦ ⑧ ⑨

1 W, 3 W (1/750 HP, 1/250 HP) 6W (1/125 HP) 15 W (1/50 HP)

① ② ③ ④

Motor Frame Size Motor Type Series Output Power (W)

0: 42 mm (1.65 in.) 2: 60 mm (2.36 in.) 3: 70 mm (2.76 in.) I: Induction Motor K: K Series (Example) 40: 40 W (1/19 HP)

⑤

Motor Shaft Type, Type of Pinion

A: Round Shaft GN: GN Type Pinion Shaft GE: GE Type Pinion Shaft

⑥

Power Supply Voltage/ Number of Poles 2, 3: RoHS-Compliant T: Terminal Box Type Included Capacitor

AW: Single-Phase 110/115 VAC 4-Pole DW: Single-Phase 220/230 VAC 2-Pole

⑦ ⑧ ⑨

4: 80 mm (3.15 in.) 5: 90 mm (3.54 in.)

BW: Single-Phase 110/115 VAC 2-Pole SW: Three-Phase 200/220/230 VAC 4-Pole

U: For Single-Phase 110/115 VAC E: For Single-Phase 220/230 VAC

CW: Single-Phase 220/230 VAC 4-Pole TW: Three-Phase 200/220/230 VAC 2-Pole

Blank: Three-Phase Type

25 W (1/30 HP)

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 (Example) Model: 5IK40GN-AW2U ➜ Motor nameplate and product approved under various safety standards: 5IK40GN-AW2

◇ Conduit Box Type

40 W (1/19 HP)

5 I K 40 GN - F C H ① ② ③

④

⑤

⑥ ⑦ ⑧

60 W (1/12 HP) 90 W (1/8 HP)

① ② ③ ④

Motor Frame Size Motor Type Series Output Power (W)

4: 80 mm (3.15 in.) 5: 90 mm (3.54 in.) I: Induction Motor K: K Series (Example) 40: 40 W (1/19 HP)

⑤

Motor Shaft Type, Type of Pinion

A, AA: Round Shaft GN: GN Type Pinion Shaft GE: GE Type Pinion Shaft

⑥ ⑦ ⑧

Power Supply Voltage C: With Capacitor H: Conduit Box Type

F: Single-Phase 110/115 VAC E: Single-Phase 220/230 VAC

S: Three-Phase 200/220/230 VAC

200 W (1/4 HP)

● Gearhead

2-Pole 40-150 W (1/19-1/5 HP)

5 GN 50 SA ① ① ② ③ ④

②

③

④

Gearhead Frame Size Type of Pinion Gear Ratio

0: 42 mm (1.65 in.) 2: 60 mm (2.36 in.) 3: 70 mm (2.76 in.) 4: 80 mm (3.15 in.) 5: 90 mm (3.54 in.) GN: GN Type Pinion GE: GE Type Pinion (Example) 50: Gear Ratio of 50:1 10X denotes the decimal gearhead of gear ratio 10:1

GN Type Pinion

SA: Long Life, Low Noise GN-S Gearhead, RoHS-Compliant KA: GN-K Gearhead, RoHS-Compliant RH: Right-Angle, Hollow Shaft Gearhead, RoHS-Compliant RAA: Right-Angle, Solid Shaft Gearhead, RoHS-Compliant

GE Type Pinion

SA: Long Life GE-S Gearhead, RoHS-Compliant RH: Right-Angle, Hollow Shaft Gearhead, RoHS-Compliant RAA: Right-Angle, Solid Shaft Gearhead, RoHS-Compliant

● BH Series

BH I 6 2 F T - 100 RH ①

A-24

②③ ④ ⑤ ⑥

⑦

⑧

① ② ③ ④ ⑤ ⑥ ⑦

Series BH: BH Series Motor Type I: Induction Motor Motor Frame Size 6: 104 mm (4.09 in.) Output Power (W) (Example) 2: 200 W (1/4 HP) Power Supply Voltage F: Single-Phase 110/115 VAC E: Single-Phase 220/230 VAC S: Three-Phase 200/220/230 VAC T: Terminal Box Type Blank: Cable Type Gear Ratio, Motor Shaft Type A: Round Shaft Type Number: Gear Ratio of Combination Type

⑧

Type of Gearhead (Combination type only)

RH: Right-Angle, Hollow Shaft Type RA: Right-Angle, Solid Shaft Type

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Blank: Parallel Shaft Type

● World K Series ◇ 1 W (1/750 HP), 3 W (1/250 HP) Type

Dielectric Strength

Sufficient to withstand 1.5 kVAC at 50 Hz or 60 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity.

Temperature Rise

Temperature rise of windings are 75˚C (135˚F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate✽.

Insulation Class Overheat Protection Ambient Temperature Ambient Humidity Degree of Protection

UL/CSA standards: Class A [105˚C (221˚F)], EN standards: Class E [120˚C (248˚F)] Impedance protected −10∼+40˚C (+14∼+104˚F) (non-freezing) 85% or less (non-condensing) IP20

Specifications 100 MΩ or more when 500 VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity.

Dielectric Strength

Sufficient to withstand 1.5 kVAC at 50 Hz or 60 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity.

Temperature Rise

Temperature rise of windings are 80˚C (144˚F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate✽. [Three-phase type: 70˚C (126˚F) or less] Class B [130˚C (266˚F)]

Overheat Protection

6 W (1/125 HP) type has impedance protection. All others have built-in thermal protector (automatic return type) Open: 130±5˚C (266±9˚F), Close: 82±15˚C (179.6±27˚F)

Ambient Temperature

Single-phase 110/115 VAC, Single-phase 220/230 VAC, Three-phase 220/230 VAC: −10∼+40˚C (+14∼+104˚F) (non-freezing) Three-phase 200 VAC: −10∼+50˚C (+14∼+122˚F) (non-freezing) 85% or less (non-condensing)

Degree of Protection

Lead Wire Type: IP20 Terminal Box Type, Conduit Box Type: IP54 (excluding the installation surface of the round shaft type)

Motor Type 1 W (1/750 HP), 3 W (1/250 HP) Type 6 W (1/125 HP) Type 15 W (1/50 HP) Type 25 W (1/30 HP) Type (2-Pole, High-Speed 4IK40 Type, 4IK60 Type) 40 W (1/19 HP) Type (2-Pole, High-Speed 5IK60 Type) 60 W (1/12 HP), 90 W (1/8 HP), 150 W (1/5 HP) Type

Size: mm (in.) 80×80 (3.15×3.15) 115×115 (4.53×4.53) 125×125 (4.92×4.92) 135×135 (5.31×5.31) 165×165 (6.50×6.50) 200×200 (7.87×7.87)

Thickness: mm (in.)

5 (0.20)

● BH Series

Dielectric Strength

Sufficient to withstand 1.5 kVAC at 50 Hz or 60 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity.

Temperature Rise

Temperature rise of windings are 70˚C (126˚F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate✽.

Insulation Class Overheat Protection

Class B [130˚C (266˚F)] Built-in thermal protector (automatic return type) Open: 150±5˚C, (302±9˚F), Close: 96±15˚C (204.8±27˚F)

Ambient Temperature

Single-phase 110/115 VAC, Single-phase 220/230 VAC, Three-phase 220/230 VAC: −10∼+40˚C (+14∼+104˚F) (non-freezing) Three-phase 200 VAC: −10∼+50˚C (+14∼+122˚F) (non-freezing) 85% or less (non-condensing)

Degree of Protection

Cable Type: IP40 Terminal Box Type: IP54 (excluding the installation surface of the round shaft type)

✽ Heat radiation plate: 230×230 mm (9.06×9.06 in.), Thickness: 5 mm (0.20 in.) (Material: Aluminum)

Linear Heads

Ambient Humidity

Right-Angle Gearheads

Specifications 100 MΩ or more when 500 VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity.

Torque Motors

Item Insulation Resistance

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

✽ Heat radiation plate (Material: Aluminum)

Clutch & Brake Motors

Ambient Humidity

V Series

Insulation Class

Electromagnetic Brake Motors

Item Insulation Resistance

Reversible Motors

◇ 6 W (1/125 HP)∼90 W (1/8 HP) Type, 2-Pole/High-Speed Type

Induction Motors

Specifications 100 MΩ or more when 500 VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity.

Introduction

Item Insulation Resistance

Standard AC Motors

■ General Specifications

Brake Pack Accessories Installation

A-25

Standard AC Motors

Induction Motors

1 W (1/750 HP), 3 W (1/250 HP) Frame Size: □42 mm (□1.65 in.)

(Gearhead sold separately) 1 W, 3 W (1/750 HP, 1/250 HP)

■ Specifications – Continuous Rating

6W (1/125 HP)

Model Lead Wire Type Pinion Shaft Type

Output Power

Round Shaft Type

W HP

15 W (1/50 HP)

0IK1GN-AW3U

0IK1A-AW3U

1 1/750

0IK3GN-BW3U

0IK3A-BW3U

3 1/250

Voltage

Frequency

VAC Single-Phase 110 Single-Phase 115 Single-Phase 110 Single-Phase 115

Hz 60 60

Current Starting Torque Rated Torque

A 0.074 0.078 0.115 0.118

Rated Speed

Capacitor

mN·m oz-in

mN·m oz-in

r/min

μF

8 1.13

8 1.13

1200

1.0

6 0.85

10 1.42

3000

1.5

25 W (1/30 HP)

● The U at the end of the model name indicates that the unit includes a capacitor. This letter is not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38 : Impedance protected

40 W (1/19 HP)

■ Product Line ● Parallel Shaft Gearhead (Sold separately)

● Motor

60 W (1/12 HP)

Type Lead Wire

Model Pinion Shaft Type 0IK1GN-AW3U 0IK3GN-BW3U

Round Shaft Type 0IK1A-AW3U 0IK3A-BW3U

90 W (1/8 HP)

The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual

Gearhead Type Parallel Shaft

GN-K Gearhead

Gearhead Model 0GN□KA

Gear Ratio 3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. Gearhead, Mounting Screws, Operating Manual

200 W (1/4 HP) 2-Pole 40-150 W (1/19-1/5 HP)

A-26

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-26

Standard AC Motors

■ Gearmotor – Torque Table

◇ 60 Hz

Unit = Upper values: N·m/Lower values: lb-in

600

500

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

0IK1GN-AW3U

0GN□KA

144

120

100

72

60

50

36

30

24

20

18

15

12

12.5 15

18

25

30

36

50

60

75

90

100 120 150 180

0.019 0.023 0.032 0.039 0.049 0.058 0.073 0.088 0.11 0.168 0.20 0.28 0.34 0.43 0.51 0.64 0.77 0.97

0.13 1.15

0.16 1.41

0.19 1.68

0.26 2.3

0.32 2.8

0.35 3.0

0.42 3.7

0.47 4.1

0.57 5.0

10

0.71 6.2

0.85 7.5

Gear Ratio

0IK3GN-BW3U

0GN□KA

1200 1000

240

200

144

120

100

72

60

48

40

12.5 15

18

25

30

36

50

60

75

90

100 120 150 180

0.024 0.029 0.041 0.049 0.061 0.073 0.091 0.11 0.21 0.25 0.36 0.43 0.53 0.64 0.80 0.97

0.13 1.15

0.17 1.50

0.20 1.77

0.24 2.1

0.33 2.9

0.40 3.5

0.44 3.8

0.53 4.6

0.59 5.2

3

720

600

480

400

5

6

7.5

9

3.6

288

36

30

24

0.71 6.2

20

0.89 7.8

1 8.8

V Series

■ Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page A-16 Gearhead ➜ Page A-16

Clutch & Brake Motors

■ Permissible Load Inertia J of Gearhead

Unit = mm (in.)

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

◇ Lead Wire Type 0GN□KA

A441U

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Motor Model

Mass: Motor 0.3 kg (0.66 lb.) Gearhead 0.2 kg (0.44 lb.)

0IK1A-AW3U 0IK3A-BW3U

0

9±

2)

0.0

20 (0.79) 1.5 (0.06)

10 (0.39)

4

10 (0.39)

4×ϕ3.5 (ϕ0.138) Thru

10 (0.39)

Installation

Detail Drawing of Protective Earth Terminal

Protective Earth Terminal M4

Accessories

Protective Earth Terminal M4

(1.89

Brake Pack

7.25 (0.29)

Protective Earth Terminal M4

2)

± 0.0

8±0.5

Linear Heads

Motor Leads 300 mm (12 in.) Length UL Style 3266, AWG22

42 (1.65)

42 (1.65)

±0

48

0

.

7 (0.28) max.

1.8 5(

4×ϕ3.5 (ϕ0.138) Thru 16.5 (0.65)

ϕ5−0.012 (ϕ0.1969−0.0005)

42 (1.65) 42 (1.65)

12.7 (0.50)

8 (0.32) ϕ18 (ϕ0.71)

20 (0.79)

A442

Right-Angle Gearheads

26 60 (2.36) (1.02) 5 (0.20) 3 (0.12)

7.5 (0.30)

2 (0.08)

DXF

Torque Motors

28 (1.10)

4.362 (0.172)

0

ϕ4.762−0.012 0 ϕ0.1875−0.0005 (3/16")

Mass 0.3 kg (0.66 lb.)

7 (0.28) max.

DXF

(ϕ1.4803−00.0010)

0IK1GN-AW3U 0IK3GN-BW3U

◇ Shaft Section of Round Shaft Type Gearhead Model

0 ϕ37.6−0.025

Motor Model

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

➜ Page A-17

■ Dimensions

Electromagnetic Brake Motors

Model Motor/ Gearhead

Reversible Motors

Unit = Upper values: N·m/Lower values: lb-in

Speed r/min

Induction Motors

Model

Speed r/min

Introduction

● Gearheads are sold separately. Decimal gearheads are not available. ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (4-pole type; 60 Hz: 1800 r/min, 2-pole type; 60 Hz: 3600 r/min) by the gear ratio. The actual speed is 2∼33% less than the displayed value, depending on the load.

● Enter the gear ratio in the box (□) within the model name.

Product Line A-26 / Dimensions A-27 / Connection Diagrams A-28

A-27

B 4.5 (0.18)

ϕ4.3 20 (ϕ0.169) (0.79)

◇ Capacitor Dimensions Pinion Shaft Type

Round Shaft Type

Capacitor Model

A

B

C

Mass g (oz.)

0IK1GN-AW3U

0IK1A-AW3U

CH10FAUL

31 14.5 23.5 (1.22) (0.57) (0.93)

18 (0.64)

0IK3GN-BW3U

0IK3A-BW3U

CH15FAUL

31 14.5 23.5 (1.22) (0.57) (0.93)

18 (0.64)

Capacitor Cap

Included

6 (0.24)

C

1 W, 3 W (1/750 HP, 1/250 HP)

AMP#187

Unit = mm (in.)

Model

B+10 (0.39)

A

10 (0.39)

Standard AC Motors

◇ Capacitor (Included)

4 (0.16)

6W (1/125 HP) 15 W (1/50 HP)

■ Connection Diagrams

25 W (1/30 HP)

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type. 0IK1GN-AW3U, 0IK3GN-BW3U Clockwise

Counterclockwise

CW

40 W (1/19 HP)

White L N

Red

L Motor

Black

CCW White Red

PE N

60 W (1/12 HP)

Capacitor

Black

Motor

PE

Capacitor

PE: Protective Earth 90 W (1/8 HP)

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. ● How to connect a capacitor ➜ Page A-313

200 W (1/4 HP) 2-Pole 40-150 W (1/19-1/5 HP)

A-28

Accessories and Peripheral Equipment Instantaneous Stop Brake Pack ➜Page A-277

Accessories ➜Page A-287

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-26

Standard AC Motors

Induction Motors

6 W (1/125 HP)

Frame Size: □60 mm (□2.36 in.) (Gearhead sold separately)

Introduction

■ Specifications – Continuous Rating

Pinion Shaft Type

Output Power W HP

Round Shaft Type

2IK6GN-AW2U

2IK6A-AW2U

Frequency

VAC Single-Phase 110 Single-Phase 115

Hz 60

Current Starting Torque Rated Torque

A 0.178 0.182

μF

41 5.8

1450

2.5

49 6.9

1150

60

0.091

40 5.6

41 5.8

1450

50

0.107

45 6.3

49 6.9

1200

60

0.094

40 5.6

41 5.8

1450

50

0.081

49 6.9

49 6.9

1200

0.072

41 5.8

41 5.8

1400

41 5.8

1500

41 5.8

1500

60 60

0.076

Three-Phase 230

60

0.079

41 5.8

−

Clutch & Brake Motors

Three-Phase 220

41 5.8

0.6

V Series

6 1/125

r/min

40 5.6 38 5.3

Three-Phase 200 2IK6A-SW2

mN·m oz-in

0.103

Single-Phase 230

2IK6GN-SW2

mN·m oz-in

Electromagnetic Brake Motors

6 1/125

2IK6A-CW2E

Capacitor

50 Single-Phase 220 2IK6GN-CW2E

Rated Speed

Reversible Motors

6 1/125

Voltage

Induction Motors

Model Lead Wire Type

: Impedance protected

■ Product Line ● Parallel Shaft Gearhead (Sold separately)

● Motor Type

Lead Wire

Model

Gearhead Type

Round Shaft Type 2IK6A-AW2U 2IK6A-CW2E 2IK6A-SW2

Long Life, Low Noise GN-S Gearhead

2GN□SA

Gear Ratio 3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

2GN10XS (Decimal Gearhead) ● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. Gearhead, Mounting Screws, Operating Manual ● Following gearheads are also available. For details, please refer to website (http://www.orientalmotor.com/) or contact the nearest Oriental Motor sales office.

Gearhead Type GN-K Gearhead

Gearhead Model Gear Ratio 2GN□KA 3∼180 2GN10XK (Decimal Gearhead)

Linear Heads

Parallel Shaft

Right-Angle Gearheads

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors

Parallel Shaft

Gearhead Model

Torque Motors

Pinion Shaft Type 2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38

● Enter the gear ratio in the box (□) within the model name. Brake Pack Accessories Installation

Product Line A-29 / Dimensions A-31 / Connection Diagrams A-32

A-29

Standard AC Motors

■ Gearmotor – Torque Table

1 W, 3 W (1/750 HP, 1/250 HP)

● Gearheads and decimal gearheads are sold separately. ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 10:1) between the gearhead and the motor. In that case, the permissible torque is 3 N·m (26 lb-in).

6W (1/125 HP)

◇ 50 Hz

Unit = Upper values: N·m/Lower values: lb-in

15 W (1/50 HP)

Model

Speed r/min

500

416

300

250

200

166

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

2GN□SA

0.12 1.06

0.14 1.23

0.20 1.77

0.24 2.1

0.30 2.6

0.36 3.1

2IK6GN-CW2E 2IK6GN-SW2

120

100

83

60

50

41

30

25

20

16

12.5 15

18

25

30

36

50

60

75

90

0.50 4.4

0.71 6.2

0.89 7.8

1.1 9.7

1.3 11.5

1.6 14.1

1.9 16.8

2.4 21

2.9 25

0.60 5.3

◇ 60 Hz

15

12.5

10

8.3

100 120 150 180 3 26

3 26

3 26

3 26

Unit = Upper values: N·m/Lower values: lb-in

25 W (1/30 HP) 40 W (1/19 HP)

Model

Speed r/min

600

500

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

2GN□SA

0.10 0.88

0.12 1.06

0.17 1.50

0.20 1.77

0.25 2.2

0.30 2.6

2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2

144

120

100

72

60

50

36

30

24

20

12.5 15

18

25

30

36

50

60

75

90

0.42 3.7

0.60 5.3

0.75 6.6

0.90 7.9

1.1 9.7

1.4 12.3

1.6 14.1

2.0 17.7

2.4 21

0.50 4.4

18

15

12

10

100 120 150 180 2.7 23

3 26

3 26

3 26

60 W (1/12 HP)

■ Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page A-16 Gearhead ➜ Page A-16

90 W (1/8 HP)

■ Permissible Load Inertia J of Gearhead

200 W (1/4 HP)

➜ Page A-17

2-Pole 40-150 W (1/19-1/5 HP)

A-30

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-29

Unit = mm (in.)

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

◇ Lead Wire Type Mass: Motor 0.7 kg (1.54 lb.) Gearhead 0.4 kg (0.88 lb.)

Motor Model

DXF

30 A443AU (1.18)

25∼180

40 A443BU (1.57)

2GN□SA

● Enter the gear ratio in the box (□) within the model name.

60 (2.36)

±

0.5

2)

0

60 (2.36)

70 6± 0. 7 ( 2. Protective Earth Terminal M4

22.5°

5 (0.20) max.

Reversible Motors

4×ϕ4.5 (ϕ0.177) Thru

Induction Motors

ϕ60 (ϕ2.36)

L

3∼18

15.5 (0.61)

12.7 (0.50)

5 (0.20)

10 (0.39) ϕ24 (ϕ0.94)

32 (1.26)

7.437 (0.293)

L

ϕ7.937−0.015 0 ϕ0.3125−0.0006 (5/16")

Gear Ratio

21.5 (0.85)

Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

Electromagnetic Brake Motors

Protective Earth Terminal M4 Detail Drawing of Protective Earth Terminal

◇ Decimal Gearhead

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Can be connected to GN pinion shaft type.

38.5 (1.51)

.5

70±0 2) ±0.0 (2.76

4×ϕ4.5 (ϕ0.177) Thru

) 0.02 .76± 0.5 (2 ± 0 7 Protective Earth Terminal M4

□60 (□2.36)

□60 (□2.36)

0

ϕ54−0.030

0

12.5 (0.49)

0 (ϕ2.1260−0.0012 )

26 (1.02) 2 (0.08)

0

0 0

A444

ϕ54−0.030 (ϕ2.1260−0.0012)

ϕ6−0.012 (ϕ0.2362−0.0005)

0.7 kg (1.54 lb.)

2GN10XS Mass: 0.2 kg (0.44 lb.) A003

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

24 2 (0.94) (0.08)

DXF

Clutch & Brake Motors

2IK6A-AW2U 2IK6A-CW2E 2IK6A-SW2

Mass

V Series

◇ Shaft Section of Round Shaft Type

Motor Model

5 (0.20) max.

4×ϕ4.5 (ϕ0.177) Thru

Torque Motors

22.5°

B+10 (0.39)

Round Shaft Type

Capacitor Model

A

B

C

Mass g (oz.)

2IK6GN-AW2U

2IK6A-AW2U

CH25FAUL2

31 17 27 (1.22) (0.67) (1.06)

21 (0.74)

2IK6GN-CW2E

2IK6A-CW2E

CH06BFAUL

31 14.5 23.5 (1.22) (0.57) (0.93)

18 (0.64)

6 (0.24)

Capacitor Cap

Included

Accessories

4 (0.16)

C

10 (0.39)

Pinion Shaft Type

Brake Pack

AMP#187

Unit = mm (in.)

Model

Linear Heads

ϕ4.3 20 (ϕ0.169) (0.79)

4.5 (0.18)

B

A

◇ Capacitor Dimensions

Right-Angle Gearheads

◇ Capacitor (Included with single-phase motors)

Introduction

2IK6GN-AW2U 2IK6GN-CW2E 2IK6GN-SW2

0

75 (2.95) 7 (0.28)

Gearhead Model

Standard AC Motors

■ Dimensions

Installation

Product Line A-29 / Dimensions A-31 / Connection Diagrams A-32

A-31

Standard AC Motors

■ Connection Diagrams ● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type. 2IK6GN-AW2U 2IK6GN-CW2E

1 W, 3 W (1/750 HP, 1/250 HP)

Clockwise

2IK6GN-SW2 Clockwise

CW White

6W (1/125 HP)

Red

L

L1(R) Motor

Black

N

L2(S)

PE

L3(T)

CW Red White

Motor

PE

Black

Capacitor

15 W (1/50 HP)

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Counterclockwise CCW

25 W (1/30 HP)

L

White Red

N

Motor

Black

PE

Capacitor 40 W (1/19 HP)

PE: Protective Earth

60 W (1/12 HP)

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. ● How to connect a capacitor ➜ Page A-313

90 W (1/8 HP)

Accessories and Peripheral Equipment Instantaneous Stop Brake Pack ➜Page A-277

Speed Control Speed Controller ➜Page B-156

Accessories ➜Page A-287

200 W (1/4 HP) 2-Pole 40-150 W (1/19-1/5 HP)

A-32

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-29

Standard AC Motors

Induction Motors

15 W (1/50 HP)

Frame Size: □70 mm (□2.76 in.) (Gearhead sold separately)

Introduction

■ Specifications – Continuous Rating

Pinion Shaft Type 3IK15GN-AW2U

Output Power

Round Shaft Type 3IK15A-AW2U

W HP

Frequency

VAC Single-Phase 110 Single-Phase 115

Hz 60

Current Starting Torque Rated Torque

A 0.33 0.34

15 1/50

mN·m oz-in

mN·m oz-in

r/min

μF

65 9.2

105 14.9

1450

4.5

0.19

70 9.9

125 17.7

1200

60

0.16

65 9.2

105 14.9

1450

50

0.19

75 10.6

125 17.7

1200

60

0.16

65 9.2

105 14.9

1450

Single-Phase 230

1.0

V Series

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38

Clutch & Brake Motors

: Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

Type Lead Wire

● Parallel Shaft Gearhead (Sold separately) Model Pinion Shaft Type 3IK15GN-AW2U 3IK15GN-CW2E

Gearhead Type

Round Shaft Type 3IK15A-AW2U 3IK15A-CW2E

The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual

Parallel Shaft

Long Life, Low Noise GN-S Gearhead

Gearhead Model 3GN□SA

Gear Ratio 3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

3GN10XS (Decimal Gearhead) ● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. Gearhead, Mounting Screws, Operating Manual ● Following gearheads are also available. For details, please refer to website (http://www.orientalmotor.com/) or contact the nearest Oriental Motor sales office.

GN-K Gearhead

Gearhead Model Gear Ratio 3GN□KA 3∼180 3GN10XK (Decimal Gearhead)

Right-Angle Gearheads

● Enter the gear ratio in the box (□) within the model name.

Torque Motors

Gearhead Type Parallel Shaft

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

■ Product Line ● Motor

Electromagnetic Brake Motors

3IK15A-CW2E

Capacitor

50 Single-Phase 220 3IK15GN-CW2E

Rated Speed

Reversible Motors

15 1/50

Voltage

Induction Motors

Model Lead Wire Type

Linear Heads Brake Pack Accessories Installation

Product Line A-33 / Dimensions A-34 / Connection Diagrams A-35

A-33

Standard AC Motors

■ Gearmotor – Torque Table

1 W, 3 W (1/750 HP, 1/250 HP)

● Gearheads and decimal gearheads are sold separately. ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 10:1) between the gearhead and the motor. In that case, the permissible torque is 5 N·m (44 lb-in).

6W (1/125 HP)

◇ 50 Hz

Unit = Upper values: N·m/Lower values: lb-in

15 W (1/50 HP)

Model

Speed r/min

500

416

300

250

200

166

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

3GN□SA

0.30 2.6

0.36 3.1

0.51 4.5

0.61 5.3

0.76 6.7

0.91 8.0

3IK15GN-CW2E

120

100

83

60

50

41

30

25

20

16

12.5 15

18

25

30

36

50

60

75

90

1.3 11.5

1.8 15.9

2.3 20

2.7 23

3.3 29

4.1 36

5 44

5 44

5 44

1.5 13.2

◇ 60 Hz

15

12.5

10

8.3

100 120 150 180 5 44

5 44

5 44

5 44

Unit = Upper values: N·m/Lower values: lb-in

25 W (1/30 HP) 40 W (1/19 HP)

Model

Speed r/min

600

500

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

3GN□SA

0.26 2.3

0.31 2.7

0.43 3.8

0.51 4.5

0.64 5.6

0.77 6.8

3IK15GN-AW2U 3IK15GN-CW2E

144

120

100

72

60

50

36

30

24

20

12.5 15

18

25

30

36

50

60

75

90

1.5 13.2

1.9 16.8

2.3 20

2.8 24

3.5 30

4.2 37

5 44

5 44

1.1 9.7

1.3 11.5

18

15

12

10

100 120 150 180 5 44

5 44

5 44

5 44

60 W (1/12 HP)

■ Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page A-16 Gearhead ➜ Page A-16

90 W (1/8 HP)

■ Permissible Load Inertia J of Gearhead ➜ Page A-17 Unit = mm (in.)

2-Pole 40-150 W (1/19-1/5 HP)

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

◇ Lead Wire Type

Motor Model

Mass: Motor 1.1 kg (2.4 lb.) Gearhead 0.55 kg (1.21 lb.)

3IK15GN-AW2U 3IK15GN-CW2E

0

12.7 (0.50)

15 (0.59) ϕ30 (ϕ1.18)

5 (0.20)

32 (1.26)

8.825 (0.347)

L

ϕ9.525−0.015 0 ϕ0.3750−0.0006 (3/8") 70 (2.76)

L

DXF

3∼18

32 A447AU (1.26)

25∼180

42 A447BU (1.65)

3GN□SA

.5

±0

)

02

82 3± 0. 2 ( 3.

Protective Earth Terminal M4

4×ϕ5.5 (ϕ0.217) Thru

22.5° Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

Gear Ratio

● Enter the gear ratio in the box (□) within the model name.

70 (2.76)

ϕ69 (ϕ2.72)

80 (3.15) 7 (0.28)

Gearhead Model

16.5 (0.65)

200 W (1/4 HP)

■ Dimensions

5 (0.20) max.

21.5 (0.85) Protective Earth Terminal M4 Detail Drawing of Protective Earth Terminal

A-34

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-33

◇ Decimal Gearhead

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Can be connected to GN pinion shaft type.

A009

43 (1.69) 13 (0.51)

0

ϕ64−0.030

30 (1.18) 2 (0.08)

2)

(3.23

4×ϕ5.5 (ϕ0.217) Thru

Protective Earth Terminal M4

Reversible Motors

□70 (□2.76)

±0.0

0.5

82±

0.5

82± .02) ±0 (3.23

□70 (□2.76)

(ϕ2.5197−00.0012)

0

A448

0 ϕ64−0.030

0

1.1 kg (2.4 lb.)

3GN10XS Mass: 0.3 kg (0.66 lb.)

Induction Motors

2 (0.08)

32 (1.26)

DXF

Introduction

ϕ6−0.012 (ϕ0.2362−0.0005)

3IK15A-AW2U 3IK15A-CW2E

Mass

0 (ϕ2.5197−0.0012 )

Motor Model

Standard AC Motors

◇ Shaft Section of Round Shaft Type

5 (0.20) max.

Electromagnetic Brake Motors

4×ϕ5.5 (ϕ0.217) Thru

22.5˚

B 4.5 (0.18) 10 (0.39)

Round Shaft Type

Capacitor Model

3IK15GN-AW2U

3IK15A-AW2U

CH45FAUL2

37 18 27 26 (1.46) (0.71) (1.06) (0.92)

3IK15GN-CW2E

3IK15A-CW2E

CH10BFAUL

37 18 27 27 (1.46) (0.71) (1.06) (0.95)

Pinion Shaft Type

A

B

C

Mass g (oz.)

Capacitor Cap

Included

4 (0.16)

C

6 (0.24)

■ Connection Diagrams

Accessories and Peripheral Equipment

Clockwise

Counterclockwise CW

Black

L Motor

White Red

PE

Motor

Black

PE

Capacitor

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

Product Line A-33 / Dimensions A-34 / Connection Diagrams A-35

Installation

● How to connect a capacitor ➜ Page A-313

Accessories

PE: Protective Earth

Brake Pack

Capacitor

N

Linear Heads

N

Red

➜Page A-287

CCW

White L

Accessories

Right-Angle Gearheads

3IK15GN-AW2U 3IK15GN-CW2E

Instantaneous Stop Brake Pack ➜Page A-277

Torque Motors

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type.

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

AMP#187

Unit = mm (in.)

Model

Clutch & Brake Motors

ϕ4.3 20 (ϕ0.169) (0.79)

◇ Capacitor Dimensions B+10 (0.39)

A

V Series

◇ Capacitor (Included)

A-35

Standard AC Motors

Induction Motors

25 W (1/30 HP)

Frame Size: □80 mm (□3.15 in.)

Lead Wire Type

Terminal Box Type (Gearhead sold separately)

1 W, 3 W (1/750 HP, 1/250 HP)

✽

■ Specifications – Continuous Rating

6W (1/125 HP)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type Dimension ①

Terminal Box Type Dimension ②

Output Power Conduit Box Type Dimension ③

15 W (1/50 HP)

4IK25GN-AW2U 4IK25GN-AW2TU 4IK25GN-FCH (4IK25A-AW2U) (4IK25A-AW2TU) (4IK25AA-FCH)

W HP 25 1/30

Voltage

Frequency

Current

VAC Single-Phase 110 Single-Phase 115

Hz

A

60

0.46

50

0.27

60

0.23

50

0.27

60

0.23

Single-Phase 220 25 W (1/30 HP)

4IK25GN-CW2E (4IK25A-CW2E)

4IK25GN-CW2TE (4IK25A-CW2TE)

−

25 1/30 Single-Phase 230

40 W (1/19 HP)

Single-Phase 220 −

−

60 W (1/12 HP)

4IK25GN-ECH (4IK25AA-ECH)

25 1/30

60 50

90 W (1/8 HP)

4IK25GN-SW2T (4IK25A-SW2T)

4IK25GN-SH (4IK25AA-SH)

25 1/30

Rated Torque

Rated Speed

Capacitor

mN·m oz-in

mN·m oz-in

r/min

μF

120 17.0

170 24

1450

6.5

205 29

1200

170 24

1450

205 29

1200

170 24

1450

170 24

1450

205 29

1200

170 24

1450

110 15.6

120 17.0

0.22 0.24

Single-Phase 230

120 17.0

1.5

200 W (1/4 HP)

60

0.22

50

0.23

240 34

190 26

1300

60

0.21

160 22

160 22

1550

Three-Phase 220

60

0.21

160 22

160 22

1600

Three-Phase 230

60

0.22

160 22

160 22

1600

Three-Phase 200 4IK25GN-SW2 (4IK25A-SW2)

Starting Torque

1.5

−

2-Pole 40-150 W (1/19-1/5 HP)

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38 ✽ Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

■ Product Line ● Motor Type

Lead Wire

Terminal Box

Conduit Box

Model Pinion Shaft Type Round Shaft Type 4IK25A-AW2U 4IK25GN-AW2U 4IK25A-CW2E 4IK25GN-CW2E 4IK25A-SW2 4IK25GN-SW2 4IK25GN-AW2TU 4IK25A-AW2TU 4IK25A-CW2TE 4IK25GN-CW2TE 4IK25A-SW2T 4IK25GN-SW2T 4IK25AA-FCH 4IK25GN-FCH 4IK25AA-ECH 4IK25GN-ECH 4IK25AA-SH 4IK25GN-SH

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors (Excluding conduit box type)

A-36

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-36

Gearhead Type

Gearhead Model

Long Life, Low Noise GN-S Gearhead

Right-Angle Shaft

Hollow Shaft Solid Shaft

Parallel Shaft

Long Life, Low Noise GN-S Gearhead

Gear Ratio

4GN□SA

Gearhead Type

3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

4GN□RH 4GN□RAA

Parallel Shaft

GN-K Gearhead

Gearhead Model Gear Ratio 4GN□KA 3∼180 4GN10XK (Decimal Gearhead)

● Enter the gear ratio in the box (□) within the model name.

Introduction

Parallel Shaft

● Following gearheads are also available. For details, please refer to website (http://www.orientalmotor.com/) or contact the nearest Oriental Motor sales office.

4GN10XS (Decimal Gearhead)

● Enter the gear ratio in the box (□) within the model name.

Induction Motors

The following items are included in each product. ● Parallel Shaft Gearhead Gearhead, Mounting Screws, Operating Manual ● Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual ● Solid Shaft Gearhead Gearhead, Mounting Screws, Gasket, Operating Manual

Reversible Motors

Unit = Upper values: N·m/ Lower values: lb-in

500

416

300

250

200

166

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□E 4IK25GN-CW2■ 4IK25GN-ECH

4GN□SA

0.50 4.4

0.60 5.3

0.83 7.3

1.0 8.8

1.2 10.6

□ 4IK25GN-SW2■ 4IK25GN-SH

4GN□SA

0.46 4.0

0.55 4.8

0.77 6.8

0.92 8.1

1.2 10.6

120

100

83

60

50

41

30

25

20

16

12.5 15

18

25

30

36

50

60

75

90

1.5 13.2

2.1 18.5

2.5 22

3.0 26

3.7 32

4.5 39

5.4 47

6.8 60

8 70

8 70

8 70

8 70

8 70

8 70

8 70

1.4 12.3

1.9 16.8

2.3 20

2.8 24

3.5 30

4.2 37

5.0 44

6.3 55

7.5 66

8 70

8 70

8 70

8 70

8 70

8 70

◇ 60 Hz

15

12.5

10

8.3

100 120 150 180

Unit = Upper values: N·m/ Lower values: lb-in

500

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□U 4IK25GN-AW2■ □E 4IK25GN-CW2■ 4IK25GN-FCH 4IK25GN-ECH

4GN□SA

0.41 3.6

0.50 4.4

0.69 6.1

0.83 7.3

1.0 8.8

□ 4IK25GN-SW2■ 4IK25GN-SH

4GN□SA

0.39 3.4

0.47 4.1

0.65 5.7

0.78 6.9

0.97 8.5

144

120

100

72

60

50

36

30

24

20

12.5 15

18

25

30

36

50

60

75

90

1.2 10.6

1.7 15.0

2.1 18.5

2.5 22

3.1 27

3.7 32

4.5 39

5.6 49

6.7 59

8 70

8 70

8 70

8 70

8 70

8 70

1.2 10.6

1.6 14.1

1.9 16.8

2.3 20

2.9 25

3.5 30

4.2 37

5.3 46

6.3 55

7.9 69

8 70

8 70

8 70

8 70

8 70

■ Gearmotor – Torque Table When Right-Angle Gearhead is Attached

Motor (Round shaft type) ➜ Page A-16 Gearhead ➜ Page A-16

➜ Page A-17

10

100 120 150 180

Accessories

■ Permissible Load Inertia J of Gearhead

12

Brake Pack

■ Permissible Overhung Load and Permissible Thrust Load

15

Linear Heads

➜ Page A-248

18

Right-Angle Gearheads

600

Torque Motors

Model

Speed r/min

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

Model

Clutch & Brake Motors

◇ 50 Hz

V Series

● Gearheads and decimal gearheads are sold separately. □) within the motor model name. ● Enter the code that represents the terminal box type "T" in the box (■ ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 10:1) between the gearhead and the motor. In that case, the permissible torque is 8 N·m (70 lb-in). When a gearhead of 25:1∼36:1 is connected, the value for permissible torque is 6 N·m (53 lb-in).

Electromagnetic Brake Motors

■ Gearmotor – Torque Table

Speed r/min

Standard AC Motors

● Parallel Shaft Gearhead/Right-Angle Gearhead (Sold separately)

Installation

Product Line A-36 / Dimensions A-38 / Connection Diagrams A-40

A-37

Unit = mm (in.)

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

◇ Lead Wire Type ①

Motor Model

Mass: Motor 1.5 kg (3.3 lb.) Gearhead 0.65 kg (1.43 lb.)

32 (1.26) 12.7 (0.50)

4IK25GN-AW2U 4IK25GN-CW2E 4IK25GN-SW2

.5

±0

80 (3.15)

6W (1/125 HP) 15 W (1/50 HP)

21.5 (0.85)

5 (0.20) max.

Protective Earth Terminal M4

25 W (1/30 HP)

Detail Drawing of Protective Earth Terminal Motor Model 4IK25GN-AW2TU 4IK25GN-CW2TE 4IK25GN-SW2T

Gear Ratio

L

DXF

3∼18

32 A451AU (1.26)

25∼180

42.5 A451BU (1.67)

4GN□SA

43 (1.69)

62 (2.44)

.5

±0

)

02

94 0± 0. 7 ( 3.

200 W (1/4 HP)

80 (3.15)

90 W (1/8 HP)

15 (0.59) ϕ34 (ϕ1.34)

60 W (1/12 HP)

0

ϕ0.3750−0.0006 (3/8") 8.825 (0.347)

Gearhead Model

● Enter the gear ratio in the box (□) within the model name.

0

ϕ9.525−0.015

ϕ79 (ϕ3.11)

40 W (1/19 HP)

Mass: Motor 1.7 kg (3.7 lb.) Gearhead 0.65 kg (1.43 lb.)

25 (0.98)

42.5 A449BU (1.67)

Protective Earth Terminal M4

◇ Terminal Box Type ②

12.7 (0.50)

25∼180

)

Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

5.5 (0.22)

DXF

32 A449AU (1.26)

02

94 0± 0. 7 ( 3.

22.5°

75 (2.95)

L

3∼18

● Enter the gear ratio in the box (□) within the model name.

4×ϕ5.5 (ϕ0.217) Thru

28 (1.10) max.

Gear Ratio

4GN□SA

(3/8") 80 (3.15)

ϕ79 (ϕ3.11)

6 (0.24)

Gearhead Model

16.5 (0.65)

L

7 (0.28)

0 ϕ9.525−0.015 0 ϕ0.3750−0.0006

15 (0.59) ϕ34 (ϕ1.34)

1 W, 3 W (1/750 HP, 1/250 HP)

85 (3.35)

8.825 (0.347)

Standard AC Motors

■ Dimensions

2-Pole 40-150 W (1/19-1/5 HP)

7 (0.28) 85 (3.35)

L

ϕ 6 (0.24) 4× 5.5 (ϕ0.217) Thru 32 (1.26)

80 (3.15)

● Use cable with a diameter of ϕ6 ∼ ϕ12 mm (ϕ0.24 ∼ ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

◇ Shaft Section of Round Shaft Type

Motor Model

0

ϕ8−0.015 (ϕ0.3150−0.0006) 0 0 ϕ73−0.030 (ϕ2.8740−0.0012)

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

DXF

1.5 kg (3.3 lb.)

A450

4IK25A-AW2TU 4IK25A-CW2TE 4IK25A-SW2T

1.7 kg (3.7 lb.)

A328

0

32 (1.26)

2)

± 0.0

0.5 94±

□80 (□3.15)

25 (0.98)

7 (0.28)

2 (0.08)

Mass

4IK25A-AW2U 4IK25A-CW2E 4IK25A-SW2

(3.70

Protective Earth Terminal M4 (Lead wire type only) 5 (0.20) max.

4×ϕ5.5 (ϕ0.217) Thru 22.5°

A-38

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-36

Standard AC Motors

◇ Conduit Box Type ③ Motor Model

Gearhead Model

4IK25GN-FCH 4IK25GN-ECH

4GN□SA

Gear Ratio L DXF 3∼18 32 (1.26) A900AU 25∼180 42.5 (1.67) A900BU

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 1.9 kg (4.2 lb.) Gearhead 0.65 kg (1.43 lb.) 75 (2.95)

0

15 (0.59) ϕ34 (ϕ1.34)

80 (3.15) L

Gearhead Model 4GN□SA

Gear Ratio L DXF 3∼18 32 (1.26) A901AU 25∼180 42.5 (1.67) A901BU

80 (3.15)

V Series

4IK25GN-SH

4×ϕ5.5 (ϕ0.217) Thru

6 (0.24) 32 (1.26)

Electromagnetic Brake Motors

85 (3.35)

● Details of terminal box ➜ Page A-314

Motor Model

0.5 ) 94± 0±0.02 (3.7

Reversible Motors

7 (0.28) 3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18

Induction Motors

ϕ79 (ϕ3.11)

12.7 (0.50)

8.825 (0.347)

ϕ9.525−0.015 0 ϕ0.3750−0.0006 (3/8")

32 (1.26)

55 (2.17)

54 (2.13)

Introduction

ϕ21.5 (ϕ0.846)

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 1.7 kg (3.7 lb.) Gearhead 0.65 kg (1.43 lb.) 0

8.825 (0.347)

0.5 ) 94± 0±0.02 (3.7

80 (3.15)

ϕ79 (ϕ3.11)

23 (0.91)

7 (0.28) 3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18

85 (3.35)

● Details of terminal box ➜ Page A-314

6 (0.24) L

4×ϕ5.5 (ϕ0.217) Thru

80 (3.15)

32 (1.26)

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Mass 1.9 kg (4.2 lb.)

DXF

Motor Model 4IK25AA-SH

A809

0

4×ϕ5.5 (ϕ0.217) Thru

80 (3.15)

2 (0.08)

80 (3.15)

0 (ϕ2.8740−0.0012 )

4×ϕ5.5 (ϕ0.217) Thru 32 (1.26)

0.5 ) 94± 0±0.02 (3.7

80 (3.15)

Installation

Product Line A-36 / Dimensions A-38 / Connection Diagrams A-40

25 (0.98)

0 ϕ73−0.030

80 (3.15)

0 (ϕ2.8740−0.0012 )

0 ϕ73−0.030

7.037 (0.28)

0.5 ) 94± 0±0.02 (3.7

Accessories

32 (1.26)

A810

Brake Pack

2 (0.08)

DXF

Linear Heads

25 (0.98)

Mass 1.7 kg (3.7 lb.)

ϕ7.937−0.011 0 ϕ0.3125−0.0004 (5/16")

0

ϕ7.937−0.011 0 ϕ0.3125−0.0004 (5/16")

7.037 (0.28)

Motor Model

Right-Angle Gearheads

◇ Shaft Section of Round Shaft Type

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Torque Motors

◇ Shaft Section of Round Shaft Type

4IK25AA-FCH 4IK25AA-ECH

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

12.7 (0.50)

15 (0.59) ϕ34 (ϕ1.34)

ϕ9.525−0.015 0 ϕ0.3750−0.0006 (3/8")

75 (2.95)

45 (1.77)

54 (2.13)

Clutch & Brake Motors

ϕ21.5 (ϕ0.846)

A-39

Can be connected to GN pinion shaft type. 4GN10XS Mass: 0.4 kg (0.88 lb.) A013

45.5 (1.79)

0

6W (1/125 HP)

□80 (□3.15)

13.5 (0.53)

ϕ73−0.030

.5

94±0 ) ±0.02 (3.70

◇ Capacitor (Included with single-phase motors)

25 W (1/30 HP)

A

B 10 (0.39)

Lead Wire Type

Capacitor Model

A

B

C

Mass g (oz.)

Capacitor Cap

Terminal Box Type

4IK25GN-AW2U (4IK25A-AW2U)

4IK25GN-AW2TU (4IK25A-AW2TU)

CH65CFAUL2

48 19 29 35 (1.89) (0.75) (1.14) (1.24)

4IK25GN-CW2E (4IK25A-CW2E)

4IK25GN-CW2TE (4IK25A-CW2TE)

CH15BFAUL

38 21 31 37 (1.50) (0.83) (1.22) (1.31)

Included

6 (0.24)

C

60 W (1/12 HP)

AMP#187

Unit = mm (in.)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type

90 W (1/8 HP)

4 (0.16)

40 W (1/19 HP)

ϕ4.3 20 (ϕ0.169) (0.79)

◇ Capacitor Dimensions

B+10 (0.39)

15 W (1/50 HP)

4×ϕ5.5 (ϕ0.217) Thru

4.5 (0.18)

1 W, 3 W (1/750 HP, 1/250 HP)

32 (1.26) 2 (0.08)

0 (ϕ2.8740−0.0012 )

Standard AC Motors

◇ Decimal Gearhead

200 W (1/4 HP)

■ Connection Diagrams

2-Pole 40-150 W (1/19-1/5 HP)

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type. Lead Wire Type 4IK25GN-AW2U 4IK25GN-CW2E

Clockwise

Clockwise

CW

N

Red

L1(R) Motor

Black

4IK25GN-AW2TU 4IK25GN-CW2TE

4IK25GN-SW2

White L

Terminal Box Type

PE

L2(S) L3(T)

Clockwise

CW Red White Black

Motor

PE

Capacitor

Capacitor

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Counterclockwise CCW

L

White Red

N

Black

PE

Capacitor

Motor

CCW

Z2 U2 U1

N Capacitor

Clockwise L1(R) L2(S) L3(T)

CW

U V W

Motor

PE

PE

Counterclockwise

L Motor

CW

Z2 U2 U1

L N

4IK25GN-SW2T

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

PE

PE: Protective Earth Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. ● How to connect a capacitor ➜ Page A-313

A-40

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-36

Clockwise NC✽ L

White Red Black

Red White Black

Green/Yellow PE

PE

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Reversible Motors

White Red Black

CCW

Motor

Motor

Green/Yellow

PE: Protective Earth

● How to connect a capacitor ➜ Page A-313

Instantaneous Stop Brake Pack ➜Page A-277

Speed Control Speed Controller ➜Page B-156

Accessories

Clutch & Brake Motors

Gearhead, Accessories and Peripheral Equipment

V Series

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

Electromagnetic Brake Motors

PE ✽NC: No connection

Space-Saving Right-Angle Gearheads ➜Page A-239

Induction Motors

N

L3(T)

CW

Green/Yellow

Counterclockwise

NC✽

L1(R) L2(S)

Motor

✽NC: No connection

L

Clockwise

Introduction

N

CW

5IK40GN-SW2T 4IK25GN-SH

Standard AC Motors

Conduit Box Type 4IK25GN-FCH 5IK40GN-AW2T□ 4IK25GN-ECH 5IK40GN-CW2T□

➜Page A-287 Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors Torque Motors Right-Angle Gearheads Linear Heads Brake Pack Accessories Installation

Product Line A-36 / Dimensions A-38 / Connection Diagrams A-40

A-41

Standard AC Motors

Induction Motors

40 W (1/19 HP)

Frame Size: □90 mm (□3.54 in.)

Lead Wire Type

Terminal Box Type (Gearhead sold separately)

1 W, 3 W (1/750 HP, 1/250 HP)

✽2

■ Specifications – Continuous Rating

6W (1/125 HP)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type Dimension ①

15 W (1/50 HP)

5IK40GN-AW2U (5IK40A-AW2U)

Terminal Box Type Dimension ② 5IK40GN-AW2TU (5IK40A-AW2TU)

Output Power Conduit Box Type Dimension ③

5IK40GN-FCH (5IK40AA-FCH)

W HP 40 1/19

Voltage

Frequency

Current

VAC Single-Phase 110 Single-Phase 115

Hz

A 0.68 0.67

60

Starting Torque

Rated Torque

Rated Speed

mN·m oz-in

mN·m oz-in

r/min

μF

200 28

260 36

1500

9.0

315 44

1250

260 36

1500

300 42

1300

260 36

1500

50

0.39

60

0.35

50

0.39

60

0.34

50

0.32

400 56

300 42

1300

60

0.30

260 36

260 36

1550

Three-Phase 220

60

0.30

260 36

260 36

1600

Three-Phase 230

60

0.31

260 36

260 36

1600

Single-Phase 220 25 W (1/30 HP)

5IK40GN-CW2E (5IK40A-CW2E)

5IK40GN-CW2TE 5IK40GN-ECH✽1 (5IK40A-CW2TE) (5IK40AA-ECH)✽1

40 1/19

200 28

Single-Phase 230 40 W (1/19 HP)

Three-Phase 200 60 W (1/12 HP)

5IK40GN-SW2 (5IK40A-SW2)

5IK40GN-SW2T (5IK40A-SW2T)

5IK40GN-SH (5IK40AA-SH)

40 1/19

Capacitor

2.3

−

90 W (1/8 HP) 200 W (1/4 HP)

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ●Details of RoHS Directive ➜ Page G-38 ✽ 1 Single-Phase 220 VAC 50Hz type is not available for conduit box type. ✽ 2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

2-Pole 40-150 W (1/19-1/5 HP)

■ Product Line ● Motor Type

Lead Wire

Terminal Box

Conduit Box

Model Pinion Shaft Type 5IK40GN-AW2U 5IK40GN-CW2E 5IK40GN-SW2 5IK40GN-AW2TU 5IK40GN-CW2TE 5IK40GN-SW2T 5IK40GN-FCH 5IK40GN-ECH 5IK40GN-SH

Round Shaft Type 5IK40A-AW2U 5IK40A-CW2E 5IK40A-SW2 5IK40A-AW2TU 5IK40A-CW2TE 5IK40A-SW2T 5IK40AA-FCH 5IK40AA-ECH 5IK40AA-SH

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors (Excluding conduit box type)

● Parallel Shaft Gearhead/Right-Angle Gearhead (Sold separately) Gearhead Type Parallel Shaft

Long Life, Low Noise GN-S Gearhead

Right-Angle Shaft

Hollow Shaft Solid Shaft

Parallel Shaft

Long Life, Low Noise GN-S Gearhead

Gearhead Model 5GN□SA 5GN□RH 5GN□RAA

Gear Ratio 3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

5GN10XS (Decimal Gearhead)

● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. ● Parallel Shaft Gearhead Gearhead, Mounting Screws, Operating Manual ● Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual ● Solid Shaft Gearhead Gearhead, Mounting Screws, Gasket, Operating Manual ● Following gearheads are also available. For details, please refer to website (http://www.orientalmotor.com/) or contact the nearest Oriental Motor sales office.

Gearhead Type Parallel Shaft

GN-K Gearhead

Gearhead Model Gear Ratio 5GN□KA 3∼180 5GN10XK (Decimal Gearhead)

● Enter the gear ratio in the box (□) within the model name.

A-42

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-42

Standard AC Motors

■ Gearmotor – Torque Table

Unit = Upper values: N·m/Lower values: lb-in

416

300

250

200

166

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□E 5IK40GN-CW2■ (Single-phase 220 VAC)

5GN□SA

0.77 6.8

0.92 8.1

1.3 11.5

1.5 13.2

1.9 16.8

2.3 20

3.2 28

□E 5IK40GN-CW2■ 5IK40GN-ECH (Single-phase 230 VAC) □ 5IK40GN-SW2■ 5IK40GN-SH

5GN□SA

0.73 6.4

0.87 7.6

1.2 10.6

1.5 13.2

1.8 15.9

2.2 19.4

3.0 26

120

100

83

60

50

41

30

25

20

16

12.5 15

18

25

30

36

50

60

75

90

3.8 33

4.6 40

5.7 50

6.9 61

8.3 73

10 88

10 88

10 88

10 88

10 88

10 88

10 88

10 88

3.6 31

4.4 38

5.5 48

6.6 58

7.9 69

9.9 87

10 88

10 88

10 88

10 88

10 88

10 88

10 88

12.5

10

8.3

100 120 150 180

Unit = Upper values: N·m/Lower values: lb-in

500

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

5GN□SA

0.63 5.5

0.76 6.7

1.1 9.7

1.3 11.5

1.6 14.1

1.9 16.8

□U 5IK40GN-AW2■ □E 5IK40GN-CW2■ □ 5IK40GN-SW2■ 5IK40GN-FCH 5IK40GN-ECH 5IK40GN-SH

144

120

100

72

60

50

36

30

24

20

12.5 15

18

25

30

36

50

60

75

90

3.8 33

4.7 41

5.7 50

6.8 60

8.6 76

10 88

10 88

10 88

2.6 23

3.2 28

18

15

12

10

100 120 150 180

10 88

10 88

10 88

10 88

■ Gearmotor – Torque Table When Right-Angle Gearhead is Attached ➜ Page A-248

■ Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page A-16 Gearhead ➜ Page A-16

Torque Motors

■ Permissible Load Inertia J of Gearhead ➜ Page A-17 Unit = mm (in.)

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

◇ Lead Wire Type ①

Motor Model 5IK40GN-AW2U 5IK40GN-CW2E 5IK40GN-SW2

60 A452BU (2.36)

5 (0.20) max.

16.5 (0.65) 21.5 (0.85) Protective Earth Terminal M4

Installation

22.5°

Product Line A-42 / Dimensions A-43 / Connection Diagrams A-46

25∼180

Protective Earth Terminal M4

4×ϕ6.5 (ϕ0.256) Thru Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

0.5 ) 4± .02 10 9± 0 0 ( 4.

DXF

3∼18 5GN□SA

● Enter the gear ratio in the box (□) within the model name.

90 (3.54)

90 (3.54)

ϕ36 (ϕ1.42)

19 (0.75)

18 (0.71)

32 (1.26) 4 (0.16) L

L

42 A452AU (1.65)

Accessories

ϕ89 (ϕ3.50)

7.5 (0.30)

Gear Ratio

Brake Pack

105 (4.13)

11.4 (0.45)

0

ϕ12.7−0.018 0 ϕ0.5000−0.0007 (1/2")

Gearhead Model

Linear Heads

Mass: Motor 2.5 kg (5.5 lb.) Gearhead 1.5 kg (3.3 lb.)

Right-Angle Gearheads

■ Dimensions

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

600

Clutch & Brake Motors

Model

Speed r/min

V Series

◇ 60 Hz

15

Electromagnetic Brake Motors

500

Reversible Motors

Model

Speed r/min

Induction Motors

◇ 50 Hz

Introduction

● Gearheads and decimal gearheads are sold separately. □) within the motor model name. ● Enter the code that represents the terminal box type "T" in the box (■ ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 10:1) between the gearhead and the motor. In that case, the permissible torque is 10 N·m (88 lb-in).

Detail Drawing of Protective Earth Terminal

A-43

5IK40GN-AW2TU 5IK40GN-CW2TE 5IK40GN-SW2T

Gear Ratio

L

DXF

3∼18

42 A454AU (1.65)

25∼180

60 A454BU (2.36)

5GN□SA

62 (2.44)

43 (1.69)

11.4 (0.45)

19 (0.75)

18 (0.71) ϕ36 (ϕ1.42)

ϕ12.7−0.018 0 ϕ0.5000−0.0007 (1/2")

6 (0.24)

0.5 ) 4± .02 10 9± 0 0 ( 4.

90 (3.54)

15 W (1/50 HP)

7.5 (0.30) 105 (4.13)

L

4 (0.16) 32 (1.26)

4×ϕ6.5 (ϕ0.256) Thru

90 (3.54)

◇ Shaft Section of Round Shaft Type

Motor Model

0

60 W (1/12 HP) 200 W (1/4 HP)

30 (1.18)

0

9 (0.35)

90 W (1/8 HP)

37 (1.46) 2 (0.08)

(ϕ3.2677−00.0014)

40 W (1/19 HP)

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Mass

DXF

5IK40A-AW2U 5IK40A-CW2E 5IK40A-SW2

2.5 kg (5.5 lb.)

A453

5IK40A-AW2TU 5IK40A-CW2TE 5IK40A-SW2T

2.6 kg (5.7 lb.)

A330

2)

±0.0

0.5

104±

□90 (□3.54)

25 W (1/30 HP)

● Use cable with a diameter of ϕ6 ∼ ϕ12 mm (ϕ0.24 ∼ ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

ϕ10−0.015 (ϕ0.3937−0.0006)

6W (1/125 HP)

ϕ89 (ϕ3.50)

1 W, 3 W (1/750 HP, 1/250 HP)

25 (0.98)

75 (2.95)

Gearhead Model

● Enter the gear ratio in the box (□) within the model name.

0

28 (1.10) max.

2-Pole 40-150 W (1/19-1/5 HP)

A-44

Motor Model

Mass: Motor 2.6 kg (5.7 lb.) Gearhead 1.5 kg (3.3 lb.)

0 ϕ83−0.035

Standard AC Motors

◇ Terminal Box Type ②

(4.09

Protective Earth Terminal M4 (Lead wire type only)

5 (0.20) max.

4×ϕ6.5 (ϕ0.256) Thru 22.5˚

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-42

Standard AC Motors

◇ Conduit Box Type ③ Motor Model

Gearhead Model

5IK40GN-FCH 5IK40GN-ECH

5GN□SA

Gear Ratio 3∼18 25∼180

L 42 (1.65) 60 (2.36)

DXF A902AU A902BU

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 2.7 kg (5.9 lb.) Gearhead 1.5 kg (3.3 lb.) 75 (2.95)

0

5IK40GN-SH

5GN□SA

90 (3.54) Gear Ratio 3∼18 25∼180

L

L 42 (1.65) 60 (2.36)

DXF A903AU A903BU

5

2)

90 (3.54)

V Series

Gearhead Model

4×ϕ6.5 (ϕ0.256) Thru

4 (0.16) 32 (1.26)

Electromagnetic Brake Motors

Motor Model

105 (4.13)

2)

104 9± 0.0 ( 4.0

Reversible Motors

7.5 (0.30) 3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18 ● Details of terminal box ➜ Page A-314

5

± 0.

ϕ89 (ϕ3.50)

19 (0.75)

Induction Motors

11.4 (0.45)

55 (2.17) 32 (1.26)

ϕ12.7−0.018 0 ϕ0.5000−0.0007 (1/2") 18 (0.71) ϕ36 (ϕ1.42)

54 (2.13)

Introduction

ϕ21.5 (ϕ0.846)

● Enter the gear ratio in the box (□) within the model name.

0

45 (1.77) 23 (0.91)

7.5 (0.30) 3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18 ● Details of terminal box ➜ Page A-314

104 9± 0.0 ( 4.0

90 (3.54)

ϕ89 (ϕ3.50)

± 0.

105 (4.13)

4 (0.16)

4×ϕ6.5 (ϕ0.256) Thru

90 (3.54)

32 (1.26)

L

Torque Motors

◇ Shaft Section of Round Shaft Type

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

37 (1.46)

5

± 0.

90 (3.54)

)

5

± 0.

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

Product Line A-42 / Dimensions A-43 / Connection Diagrams A-46

90 (3.54)

Installation

4×ϕ6.5 (ϕ0.256) Thru

2)

104 9± 0.0 ( 4.0

(

0

0 ϕ3.2677−0.0014

30 (1.18)

0

ϕ9.525−0.011 0 ϕ0.3750−0.0005 (3/8")

Accessories

ϕ83−0.035

2)

104 9± 0.0 ( 4.0

A812

90 (3.54)

2 (0.08)

DXF

0 (ϕ3.2677−0.0014 )

0

ϕ9.525−0.011 0 ϕ0.3750−0.0005 (3/8") 8.825 (0.35)

30 (1.18)

5IK40AA-SH

A811

Mass 2.5 kg (5.5 lb.)

Brake Pack

2 (0.08)

Motor Model

Linear Heads

37 (1.46)

DXF

0 ϕ83−0.035

Mass 2.7 kg (5.9 lb.)

8.825 (0.35)

Motor Model

Right-Angle Gearheads

◇ Shaft Section of Round Shaft Type

5IK40AA-FCH 5IK40AA-ECH

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

19 (0.75)

18 (0.71) ϕ36 (ϕ1.42)

ϕ12.7−0.018 0 ϕ0.5000−0.0007 (1/2")

75 (2.95)

54 (2.13)

11.4 (0.45)

ϕ21.5 (ϕ0.846)

Clutch & Brake Motors

Mass: Motor 2.5 kg (5.5 lb.) Gearhead 1.5 kg (3.3 lb.)

A-45

Standard AC Motors

◇ Decimal Gearhead Can be connected to GN pinion shaft type. 5GN10XS Mass: 0.6 kg (1.32 lb.) A022

55 (2.17) 18 (0.71)

0.5

□90 (□3.54)

0

ϕ83−0.035

6W (1/125 HP)

0 (ϕ3.2677−0.0014 )

104± 2) ±0.0 (4.09

15 W (1/50 HP)

4×ϕ6.5 (ϕ0.256) Thru

A

AMP#187

◇ Capacitor Dimensions

Unit = mm (in.)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type

Capacitor Model

A

B

C

Mass g (oz.)

Capacitor Cap

Terminal Box Type

5IK40GN-AW2U (5IK40A-AW2U)

5IK40GN-AW2TU (5IK40A-AW2TU)

CH90CFAUL2

48 22.5 31.5 45 (1.89) (0.89) (1.24) (1.59)

5IK40GN-CW2E (5IK40A-CW2E)

5IK40GN-CW2TE (5IK40A-CW2TE)

CH23BFAUL

48 21 31 43 (1.89) (0.83) (1.22) (1.52)

Included

6 (0.24)

C

60 W (1/12 HP)

10 (0.39)

40 W (1/19 HP)

ϕ4.3 20 (ϕ0.169) (0.79)

4.5 (0.18)

B

25 W (1/30 HP)

◇ Capacitor (Included with single-phase motors) B+10 (0.39)

1 W, 3 W (1/750 HP, 1/250 HP)

37 (1.46) 2 (0.08)

4 (0.16)

90 W (1/8 HP) 200 W (1/4 HP)

■ Connection Diagrams

2-Pole 40-150 W (1/19-1/5 HP)

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type.

Lead Wire Type 5IK40GN-AW2U 5IK40GN-AW2M 5IK40GN-CW2E 5IK40GN-CW2M Clockwise

5IK40GN-SW2 Clockwise

CW White

L N

Red

L1(R) Motor

Black

Terminal Box Type 5IK40GN-AW2TU 5IK40GN-AW2TM 5IK40GN-CW2TE 5IK40GN-CW2TM

PE

L2(S) L3(T)

Clockwise

CW Red White Black

Motor

PE

Capacitor

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Counterclockwise CCW

L

White Red

N

Black

L N

Z2 U2 U1

Capacitor

PE

PE

Capacitor

Motor

CCW

Z2 U2 U1

N Capacitor

Clockwise L1(R) L2(S) L3(T)

CW

U V W

Motor

PE

Counterclockwise

L Motor

CW

5IK40GN-SW2T 5IK40GN-SW2T

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

PE

PE: Protective Earth Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. ● How to connect a capacitor ➜ Page A-313

A-46

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-42

Clockwise NC✽ L

White Red Black

Red White Black

Green/Yellow PE

PE

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

Reversible Motors

White Red Black

CCW

Motor

Green/Yellow

PE: Protective Earth

● How to connect a capacitor ➜ Page A-313

Instantaneous Stop Brake Pack ➜Page A-277

Speed Control Speed Controller ➜Page B-156

Accessories

Clutch & Brake Motors

Gearhead, Accessories and Peripheral Equipment

V Series

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

Electromagnetic Brake Motors

PE ✽NC: No connection

Space-Saving Right-Angle Gearheads ➜Page A-239

Induction Motors

N

L3(T)

CW

Green/Yellow

Counterclockwise

NC✽

L1(R) L2(S)

Motor

✽NC: No connection

L

Clockwise

Introduction

N

CW

5IK40GN-SW2T 5IK40GN-SH

Standard AC Motors

Conduit Box Type 5IK40GN-FCH 5IK40GN-AW2T□ 5IK40GN-ECH 5IK40GN-CW2T□

➜Page A-287 Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors Torque Motors Right-Angle Gearheads Linear Heads Brake Pack Accessories Installation

Product Line A-42 / Dimensions A-43 / Connection Diagrams A-46

A-47

Standard AC Motors

Induction Motors

60 W (1/12 HP)

Frame Size: □90 mm (□3.54 in.)

Lead Wire Type

Terminal Box Type (Gearhead sold separately)

1 W, 3 W (1/750 HP, 1/250 HP)

✽2

■ Specifications – Continuous Rating

6W (1/125 HP)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type Dimension ①

15 W (1/50 HP)

5IK60GE-AW2U (5IK60A-AW2U)

Terminal Box Type Dimension ②

Output Power Conduit Box Type Dimension ③

5IK60GE-AW2TU 5IK60GE-FCH (5IK60A-AW2TU) (5IK60A-FCH)

W HP 60 1/12

Voltage

Frequency

Current

VAC Single-Phase 110 Single-Phase 115

Hz

A 1.09 1.10

60

Starting Torque

Rated Torque

Rated Speed

Capacitor

mN·m oz-in

mN·m oz-in

r/min

μF

320 45

405 57

1450

18

490 69

1200

405 57

1450

490 69

1200

405 57

1450

50

0.55

60

0.54

50

0.57

60

0.54

50

0.50

600 85

450 63

1300

60

0.43

500 71

380 53

1550

Three-Phase 220

60

0.45

500 71

380 53

1600

Three-Phase 230

60

0.46

500 71

380 53

1600

Single-Phase 220 25 W (1/30 HP)

5IK60GE-CW2E (5IK60A-CW2E)

5IK60GE-CW2TE (5IK60A-CW2TE)

5IK60GE-ECH✽1 (5IK60A-ECH)✽1

60 1/12

320 45

Single-Phase 230 40 W (1/19 HP)

Three-Phase 200 60 W (1/12 HP)

5IK60GE-SW2 (5IK60A-SW2)

5IK60GE-SW2T (5IK60A-SW2T)

5IK60GE-SH (5IK60A-SH)

−

90 W (1/8 HP) 200 W (1/4 HP)

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38 ✽ 1 Single-Phase 220 VAC 50Hz type is not available for conduit box type. ✽ 2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

2-Pole 40-150 W (1/19-1/5 HP)

■ Product Line ● Motor Type

Lead Wire

Terminal Box

Conduit Box

Model Pinion Shaft Type 5IK60GE-AW2U 5IK60GE-CW2E 5IK60GE-SW2 5IK60GE-AW2TU 5IK60GE-CW2TE 5IK60GE-SW2T 5IK60GE-FCH 5IK60GE-ECH 5IK60GE-SH

Round Shaft Type 5IK60A-AW2U 5IK60A-CW2E 5IK60A-SW2 5IK60A-AW2TU 5IK60A-CW2TE 5IK60A-SW2T 5IK60A-FCH 5IK60A-ECH 5IK60A-SH

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors (Excluding conduit box type)

A-48

60 1/12

4.0

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

● Parallel Shaft Gearhead/Right-Angle Gearhead (Sold separately) Gearhead Type Parallel Shaft

Long Life GE-S Gearhead

Right-Angle Shaft

Hollow Shaft Solid Shaft

Parallel Shaft

Long Life GE-S Gearhead

Gearhead Model 5GE□SA 5GE□RH 5GE□RAA

Gear Ratio 3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

5GE10XS (Decimal Gearhead)

● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. ● Parallel Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Operating Manual ● Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual ● Solid Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Gasket, Operating Manual

Features A-20 / System Configuration A-23 / Specifications A-48

Standard AC Motors

■ Gearmotor – Torque Table

Unit = Upper values: N·m/Lower values: lb-in

416

300

250

200

166

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□E 5IK60GE-CW2■ 5IK60GE-ECH

5GE□SA

1.2 10.6

1.4 12.3

2.0 17.7

2.4 21

3.0 26

3.6 31

4.5 39

□ 5IK60GE-SW2■ 5IK60GE-SH

5GE□SA

1.1 9.7

1.3 11.5

1.8 15.9

2.2 19.4

2.7 23

3.3 29

4.1 36

120

100

83

60

50

41

30

25

20

16

12.5 15

18

25

30

36

50

60

75

90

5.4 47

6.4 56

8.1 71

9.7 85

11.6 102

16.2 143

19.4 171

20 177

20 177

20 177

20 177

20 177

20 177

4.9 43

5.9 52

7.4 65

8.9 78

10.7 94

14.9 131

17.8 157

19.9 176

20 177

20 177

20 177

20 177

20 177

◇ 60 Hz

15

12.5

10

8.3

100 120 150 180

Unit = Upper values: N·m/Lower values: lb-in

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□U 5IK60GE-AW2■ □E 5IK60GE-CW2■ 5IK60GE-FCH 5IK60GE-ECH

5GE□SA

0.98 8.6

1.2 10.6

1.6 14.1

2.0 17.7

2.5 22

3.0 26

3.7 32

□ 5IK60GE-SW2■ 5IK60GE-SH

5GE□SA

0.92 8.1

1.1 9.7

1.5 13.2

1.8 15.9

2.3 20

2.8 24

3.5 30

144

120

100

72

60

50

36

30

24

20

18

15

12

10

12.5 15

18

25

30

36

50

60

75

90

4.4 38

5.3 46

6.7 59

8.0 70

9.6 84

13.4 118

16.0 141

17.9 158

20 177

20 177

20 177

20 177

20 177

4.2 37

5.0 44

6.3 55

7.5 66

9.0 79

12.5 110

15.0 132

16.8 148

20 177

20 177

20 177

20 177

20 177

100 120 150 180

■ Gearmotor – Torque Table When Right-Angle Gearhead is Attached ➜ Page A-248

■ Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page A-16 Gearhead ➜ Page A-16

■ Permissible Load Inertia J of Gearhead

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

500

Clutch & Brake Motors

600

V Series

Model

Speed r/min

Electromagnetic Brake Motors

500

Reversible Motors

Model

Speed r/min

Induction Motors

◇ 50 Hz

Introduction

● Gearheads and decimal gearheads are sold separately. □) within the motor model name. ● Enter the code that represents the terminal box type "T" in the box (■ ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 10:1) between the gearhead and the motor. In that case, the permissible torque is 20 N·m (177 lb-in).

➜ Page A-17 Torque Motors

■ Dimensions

Unit = mm (in.)

◇ Lead Wire Type ①

Motor Model

A455U

● Enter the gear ratio in the box (□) within the model name.

90 (3.54)

90 (3.54)

0.5 ) 4± .02 10 9± 0 0 ( 4.

Protective Earth Terminal M4

No.10-24UNC×10 (0.39) Deep

22.5°

Product Line A-48 / Dimensions A-49 / Connection Diagrams A-53

5 (0.20) max.

Protective Earth Terminal M4

Installation

21.5 (0.85)

4×ϕ6.5 (ϕ0.256) Thru Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

16.5 (0.65)

ϕ15.875−0.011 0 ϕ0.6250−0.0004 (5/8") ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

65 (2.56) 38 (1.50) 7 (0.28) 29.5±0.5 (1.16±0.02) 28.58 (1.125)

Accessories

□90 (□3.54)

5GE□SA

Brake Pack

7.5 (0.30)

DXF

Linear Heads

0

120 (4.72)

Gearhead Model

5IK60GE-AW2U 5IK60GE-CW2E 5IK60GE-SW2

Mass: Motor 2.7 kg (5.9 lb.) Gearhead 1.5 kg (3.3 lb.)

Right-Angle Gearheads

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

Detail Drawing of Protective Earth Terminal

A-49

Motor Model

Mass: Motor 2.8 kg (6.2 lb.) Gearhead 1.5 kg (3.3 lb.)

5IK60GE-AW2TU 5IK60GE-CW2TE 5IK60GE-SW2T

Gearhead Model

DXF

5GE□SA

A457U

● Enter the gear ratio in the box (□) within the model name.

6 (0.24)

(5/8")

62 (2.44) 43 (1.69)

6W (1/125 HP)

29.5±0.5 (1.16±0.02) 28.58 (1.13)

90 (3.54)

25 (0.98)

75 (2.95)

ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

1 W, 3 W (1/750 HP, 1/250 HP)

□90 (□3.54)

28 (1.10) max.

ϕ15.875−00.011 0 ϕ0.6250−0.0004

No.10-24UNC×10 (0.39) Deep

15 W (1/50 HP)

7.5 (0.30) 120 (4.72)

0.5 ) 4± .02 10 9± 0 0 ( 4.

7 (0.28) 65 (2.56) 38 (1.50)

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

◇ Key and Key Slot

+0.1

2.743 0 (0.108+00.004)

0

4.763−0.03

4.763

+0.040 0

(0.1875+0.0016 ) 0

0 (0.1875−0.0012 )

Motor Model

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

0

11 (0.43)

2-Pole 40-150 W (1/19-1/5 HP)

30 (1.18)

0

Mass

DXF

5IK60A-AW2U 5IK60A-CW2E 5IK60A-SW2

2.7 kg (5.9 lb.)

A456

5IK60A-AW2TU 5IK60A-CW2TE 5IK60A-SW2T

2.8 kg (6.2 lb.)

A332

0

0

200 W (1/4 HP)

37 (1.46) 2 (0.08)

ϕ83−0.035 (ϕ3.2677−0.0014)

90 W (1/8 HP)

◇ Shaft Section of Round Shaft Type

ϕ12−0.018 (ϕ0.4724−0.0007)

60 W (1/12 HP)

28.58±0.2 (1.125±0.008)

0 (0.1875−0.0012 )

0

40 W (1/19 HP)

(The key is included with the gearhead) 4.763−0.03

25 W (1/30 HP)

● Use cable with a diameter of ϕ6 ∼ ϕ12 mm (ϕ0.24 ∼ ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

2)

± 0.0

.5

0 104±

□90 (□3.54)

Standard AC Motors

◇ Terminal Box Type ②

(4.09

Protective Earth Terminal M4 (Lead wire type only)

5 (0.20) max.

4×ϕ6.5 (ϕ0.256) Thru 22.5˚

A-50

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-48

Standard AC Motors

◇ Conduit Box Type ③ Motor Model 5IK60GE-FCH 5IK60GE-ECH

Gearhead Model

DXF

5GE□SA

A904U

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 3.2 kg (7.0 lb.) Gearhead 1.5 kg (3.3 lb.) 74 (2.91)

ϕ21.5 (ϕ0.846)

100 (3.94) Introduction

ϕ15.875−00.011 ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

90 (3.54)

☐90 (☐3.54) 3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18 ● Details of terminal box ➜ Page A-314

0.5 ) 4± .02 10 9± 0 0 ( 4.

7 (0.28) 65 (2.56) 38 (1.50)

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

V Series

◇ Key and Key Slot

+0.1 0

(0.108+00.004)

4.763

+0.040 0

(0.1875+0.0016 ) 0

0 (0.1875−0.0012 )

Gearhead Model 5GE□SA

DXF A905U

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

Motor Model 5IK60GE-SH

2.743

0

0 (0.1875−0.0012 )

0

4.763−0.03

Clutch & Brake Motors

4.763−0.03

(The key is included with the gearhead)

28.58±0.2 (1.125±0.008)

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 2.8 kg (6.2 lb.) Gearhead 1.5kg (3.3 lb.) ϕ21.5 (ϕ0.846)

Electromagnetic Brake Motors

7.5 (0.30) 120 (4.72)

Reversible Motors

No.10-24UNC×10 (0.39) Deep

Induction Motors

31 (1.22)

65 (2.56)

0

ϕ0.6250−0.0004 (5/8") 29.5±0.5 (1.16±0.02) 28.58 (1.13)

54 (2.13)

ϕ15.875−00.011

75 (2.95)

0

☐90 (☐3.54)

23 (0.91) 3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18 ● Details of terminal box ➜ Page A-314

7 (0.28) 65 (2.56) 38 (1.50)

0.5 ) 4± .02 10 9± 0 0 ( 4.

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

Right-Angle Gearheads

7.5 (0.30) 120 (4.72)

Torque Motors

No.10-24UNC×10 (0.39) Deep

90 (3.54)

45 (1.77)

(1.16±0.02) 28.58 (1.13)

ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

ϕ0.6250−0.0004 (5/8") 29.5±0.5

Linear Heads

◇ Key and Key Slot

+0.1 0

(0.108+00.004)

(

0 0.1875−0.0012

+0.040 0 +0.0016 0.1875 0

4.763

)

(

)

2.743

0

0

4.763−0.03

Accessories

0 (0.1875−0.0012 )

28.58±0.2 (1.125±0.008)

Brake Pack

4.763−0.03

(The key is included with the gearhead)

Installation

Product Line A-48 / Dimensions A-49 / Connection Diagrams A-53

A-51

Standard AC Motors

◇ Shaft Section of Round Shaft Type

◇ Shaft Section of Round Shaft Type

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Motor Model

Mass

5IK60A-FCH 5IK60A-ECH

DXF

3.2 kg (7.0 lb.)

Motor Model 5IK60A-SH

A813

Mass

DXF

2.8 kg (6.2 lb.)

A814

0 (ϕ0.4724−0.0007 )

30 (1.18)

4×ϕ6.5 (ϕ0.256) Thru

2 (0.08) 25 W (1/30 HP)

2 (0.08) 90 (3.54)

37 (1.46)

5

± 0.

2)

104 9± 0.0 ( 4.0

90 (3.54)

± 0.5

104 9±0.02) (4.0

90 (3.54)

15 W (1/50 HP)

0 ϕ83−0.035

30 (1.18)

)

0 (ϕ3.2677−0.0014 )

11(0.43)

6W (1/125 HP)

(

0 ϕ12−0.018

0 (ϕ3.2677−0.0014 )

0 ϕ0.4724−0.0007

0 ϕ83−0.035

0 ϕ12−0.018

11 (0.43)

1 W, 3 W (1/750 HP, 1/250 HP)

65 (2.56)

74 (2.91)

4×ϕ6.5 (ϕ0.256) Thru

37 (1.46)

90 (3.54)

◇ Decimal Gearhead

40 W (1/19 HP)

Can be connected to GE pinion shaft type. 5GE10XS Mass: 0.6 kg (1.32 lb.) A029

0

ϕ83−0.035

90 W (1/8 HP) 200 W (1/4 HP)

□90 (□3.54)

40 (1.57) 21 2 (0.83) (0.08) 0 (ϕ3.2677−0.0014 )

0.5 104± ) 0.02 (4.09±

4×ϕ10.8 (ϕ0.425) Thru

A

◇ Capacitor Dimensions

Unit = mm (in.)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type

Capacitor Model

A

B

C

Mass g (oz.)

Capacitor Cap

Terminal Box Type

5IK60GE-AW2U (5IK60A-AW2U)

5IK60GE-AW2TU (5IK60A-AW2TU)

CH180CFAUL2

58 29 41 (2.28) (1.14) (1.61)

92 (3.2)

5IK60GE-CW2E (5IK60A-CW2E)

5IK60GE-CW2TE (5IK60A-CW2TE)

CH40BFAUL

58 23.5 37 (2.28) (0.93) (1.46)

73 (2.6)

Included

6 (0.24)

R (R 10 0.3 9)

4 (0.16)

C

AMP#187

10 (0.39)

ϕ4.3 20 (ϕ0.169) ( 0.79)

7 (0.28)

B

2-Pole 40-150 W (1/19-1/5 HP)

◇ Capacitor (Included with single-phase motors) B+15 (0.59)

60 W (1/12 HP)

61 (2.40)

A-52

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-48

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type. Lead Wire Type

Terminal Box Type

Clockwise

5IK60GE-SW2 Clockwise

CW White

White

L2(S)

PE

Black

N

Red

L1(R) Motor

Clockwise

CW

Motor

PE

Black

L3(T)

Capacitor

Counterclockwise CCW

Red

Z2 U2 U1

Capacitor

PE

PE

U V W

Motor

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

PE

V Series

Capacitor

Z2 U2 U1

L1(R) L2(S) L3(T)

CW

PE

CCW

N

Capacitor

Motor

Counterclockwise

L Motor

Black

N

L N

Clockwise

Electromagnetic Brake Motors

White

L

CW

Reversible Motors

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

5IK60GE-SW2T

Induction Motors

Red

L

5IK60GE-AW2TU 5IK60GE-CW2TE

Introduction

5IK60GE-AW2U 5IK60GE-CW2E

Standard AC Motors

■ Connection Diagrams

Conduit Box Type

NC✽ L N

CW White Red Black

N

L1(R) L2(S) L3(T)

CW Red White Black

Motor

Green/Yellow

Green/Yellow

PE

PE

Counterclockwise

NC✽

Clockwise

Motor

✽NC: No connection

L

5IK40GN-SW2T 5IK60GE-SH

White Red Black

CCW

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

Torque Motors

Green/Yellow

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

Clockwise

Clutch & Brake Motors

5IK60GE-FCH 5IK40GN-AW2T□ 5IK60GE-ECH 5IK40GN-CW2T□

PE ✽NC: No connection

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

Linear Heads

● How to connect a capacitor ➜ Page A-313

Right-Angle Gearheads

PE: Protective Earth

Gearhead, Accessories and Peripheral Equipment Instantaneous Stop Brake Pack ➜Page A-277

Speed Control Speed Controller ➜Page B-156

Accessories ➜Page A-287

Brake Pack

Space-Saving Right-Angle Gearheads ➜Page A-239

Accessories Installation

Product Line A-48 / Dimensions A-49 / Connection Diagrams A-53

A-53

Standard AC Motors

Induction Motors

90 W (1/8 HP)

Frame Size: □90 mm (□3.54 in.)

Lead Wire Type

Terminal Box Type (Gearhead sold separately)

1 W, 3 W (1/750 HP, 1/250 HP)

✽2

■ Specifications – Continuous Rating

6W (1/125 HP)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type Dimension ①

15 W (1/50 HP)

5IK90GE-AW2U (5IK90A-AW2U)

Terminal Box Type Dimension ②

Output Power Conduit Box Type Dimension ③

5IK90GE-AW2TU 5IK90GE-FCH (5IK90A-AW2TU) (5IK90A-FCH)

W HP 90 1/8

Voltage

Frequency

Current

VAC Single-Phase 110 Single-Phase 115

Hz

A 1.45 1.44

60

Starting Torque

Rated Torque

Rated Speed

Capacitor

mN·m oz-in

mN·m oz-in

r/min

μF

450 63

585 83

1500

20

730 103

1200

605 85

1450

730 103

1200

605 85

1450

50

0.74

60

0.82

50

0.76

60

0.81

50

0.64

850 120

680 96

1300

60

0.59

700 99

570 80

1550

Three-Phase 220

60

0.60

700 99

570 80

1600

Three-Phase 230

60

0.61

700 99

570 80

1600

Single-Phase 220 25 W (1/30 HP)

5IK90GE-CW2E (5IK90A-CW2E)

5IK90GE-CW2TE (5IK90A-CW2TE)

5IK90GE-ECH✽1 (5IK90A-ECH)✽1

90 1/8

450 63

Single-Phase 230 40 W (1/19 HP)

Three-Phase 200

60 W (1/12 HP)

5IK90GE-SW2 (5IK90A-SW2)

5IK90GE-SW2T (5IK90A-SW2T)

5IK90GE-SH (5IK90A-SH)

−

90 W (1/8 HP) 200 W (1/4 HP)

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38 ✽ 1 Single-Phase 220 VAC 50Hz type is not available for conduit box type. ✽ 2 Conduit box type is not certified under the China Compulsory Certification System (CCC System). : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

2-Pole 40-150 W (1/19-1/5 HP)

■ Product Line ● Motor Type

Lead Wire

Terminal Box

Conduit Box

Model Pinion Shaft Type 5IK90GE-AW2U 5IK90GE-CW2E 5IK90GE-SW2 5IK90GE-AW2TU 5IK90GE-CW2TE 5IK90GE-SW2T 5IK90GE-FCH 5IK90GE-ECH 5IK90GE-SH

Round Shaft Type 5IK90A-AW2U 5IK90A-CW2E 5IK90A-SW2 5IK90A-AW2TU 5IK90A-CW2TE 5IK90A-SW2T 5IK90A-FCH 5IK90A-ECH 5IK90A-SH

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors (Excluding conduit box type)

A-54

90 1/8

6.0

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

● Parallel Shaft Gearhead/Right-Angle Gearhead (Sold separately) Gearhead Type Parallel Shaft

Long Life GE-S Gearhead

Right-Angle Shaft

Hollow Shaft Solid Shaft

Parallel Shaft

Long Life GE-S Gearhead

Gearhead Model 5GE□SA 5GE□RH 5GE□RAA

Gear Ratio 3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

5GE10XS (Decimal Gearhead)

● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. ● Parallel Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Operating Manual ● Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual ● Solid Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Gasket, Operating Manual

Features A-20 / System Configuration A-23 / Specifications A-54

Standard AC Motors

■ Gearmotor – Torque Table

Unit = Upper values: N·m/Lower values: lb-in

416

300

250

200

166

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□E 5IK90GE-CW2■ 5IK90GE-ECH

5GE□SA

1.8 15.9

2.1 18.5

3.0 26

3.5 30

4.4 38

5.3 46

6.7 59

□ 5IK90GE-SW2■ 5IK90GE-SH

5GE□SA

1.7 15.0

2.0 17.7

2.8 24

3.3 29

4.1 36

5.0 44

6.2 54

120

100

83

60

50

41

30

25

20

16

12.5 15

18

25

30

36

50

60

75

90

8.0 70

9.6 84

12.0 106

14.5 128

17.3 153

20 177

20 177

20 177

20 177

20 177

20 177

20 177

20 177

7.4 65

8.9 78

11.2 99

13.5 119

16.2 143

20 177

20 177

20 177

20 177

20 177

20 177

20 177

20 177

◇ 60 Hz

15

12.5

10

8.3

100 120 150 180

Unit = Upper values: N·m/Lower values: lb-in

360

300

240

200

Motor/ Gearhead

Gear Ratio

3

3.6

5

6

7.5

9

□U 5IK90GE-AW2■ 5IK90GE-FCH

5GE□SA

1.4 12.3

1.7 15.0

2.4 21

2.8 24

3.6 31

4.3 38

5.3 46

□E 5IK90GE-CW2■ 5IK90GE-ECH

5GE□SA

1.5 13.2

1.8 15.9

2.5 22

2.9 25

3.7 32

4.4 38

□ 5IK90GE-SW2■ 5IK90GE-SH

5GE□SA

1.4 12.3

1.7 15.0

2.3 20

2.8 24

3.5 30

4.2 37

144

120

100

72

60

50

36

30

24

20

18

15

12

10

12.5 15

18

25

30

36

50

60

75

90

6.4 56

7.7 68

9.7 85

11.6 102

13.9 123

19.3 170

20 177

20 177

20 177

20 177

20 177

20 177

20 177

5.5 48

6.6 58

7.9 69

10.0 88

12.0 106

14.4 127

20 177

20 177

20 177

20 177

20 177

20 177

20 177

20 177

5.2 46

6.2 54

7.5 66

9.4 83

11.3 100

13.5 119

18.8 166

20 177

20 177

20 177

20 177

20 177

20 177

20 177

100 120 150 180

■ Gearmotor – Torque Table When Right-Angle Gearhead is Attached ➜ Page A-248

■ Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page G-16 Gearhead ➜ Page G-16

■ Permissible Load Inertia J of Gearhead ■ Dimensions

Torque Motors

➜ Page G-17 Unit = mm (in.)

◇ Lead Wire Type ①

Motor Model

Mass: Motor 3.2 kg (7.0 lb.) Gearhead 1.5 kg (3.3 lb.) ϕ15.875−00.011

DXF

5GE□SA

A458U

● Enter the gear ratio in the box (□) within the model name.

0

0.5 ) 4± .02 10 9± 0 0 ( 4.

Protective Earth Terminal M4

Accessories

90 (3.54)

90 (3.54)

16.5 (0.65)

ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

ϕ0.6250−0.0004 (5/8") Brake Pack

7.5 (0.30)

65 (2.56) 38 (1.50) 7 (0.28) 29.5±0.5 (1.16±0.02) 28.58 (1.13)

Gearhead Model

Linear Heads

135 (5.31)

5IK90GE-AW2U 5IK90GE-CW2E 5IK90GE-SW2

Right-Angle Gearheads

● Mounting screws are included with gearheads. Dimensions for mounting screws ➜ Page A-310

□90 (□3.54)

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

500

Clutch & Brake Motors

600

V Series

Model

Speed r/min

Electromagnetic Brake Motors

500

Reversible Motors

Model

Speed r/min

Induction Motors

◇ 50 Hz

Introduction

● Gearheads and decimal gearheads are sold separately. □) within the motor model name. ● Enter the code that represents the terminal box type "T" in the box (■ ● Enter the gear ratio in the box (□) within the gearhead model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 10:1) between the gearhead and the motor. In that case, the permissible torque is 20 N·m (177 lb-in).

No.10-24UNC×10 (0.39) Deep

22.5° Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

Product Line A-54 / Dimensions A-55 / Connection Diagrams A-59

5 (0.20) max.

21.5 (0.85) Protective Earth Terminal M4

Installation

4×ϕ6.5 (ϕ0.256) Thru

Detail Drawing of Protective Earth Terminal

A-55

Motor Model

Mass: Motor 3.3 kg (7.3 lb.) Gearhead 1.5 kg (3.3 lb.)

5IK90GE-AW2TU 5IK90GE-CW2TE 5IK90GE-SW2T

Gearhead Model

DXF

5GE□SA

A460U

● Enter the gear ratio in the box (□) within the model name.

6 (0.24)

62 (2.44)

0

ϕ0.6250−0.0004 (5/8")

43 (1.69)

25 (0.98)

1 W, 3 W (1/750 HP, 1/250 HP)

29.5±0.5 (1.16±0.02) 28.58 (1.13)

6W (1/125 HP)

90 (3.54)

75 (2.95)

ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

28 (1.10) max.

ϕ15.875−00.011

□90 (□3.54)

Standard AC Motors

◇ Terminal Box Type ②

No.10-24UNC×10 (0.39) Deep

15 W (1/50 HP)

7.5 (0.30) 135 (5.31)

0.5 ) 4± .02 10 9± 0 0 ( 4.

7 (0.28) 65 (2.56) 38 (1.50)

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

25 W (1/30 HP)

● Use cable with a diameter of ϕ6 ∼ ϕ12 mm (ϕ0.24 ∼ ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

◇ Key and Key Slot

+0.1

2.743 0 (0.108+00.004)

0

4.763−0.03

4.763

+0.040 0

(0.1875+0.0016 ) 0

0 (0.1875−0.0012 )

Motor Model

0

11 (0.43)

2-Pole 40-150 W (1/19-1/5 HP)

30 (1.18)

0

Mass

DXF

5IK90A-AW2U 5IK90A-CW2E 5IK90A-SW2

3.2 kg (7.0 lb.)

A459

5IK90A-AW2TU 5IK90A-CW2TE 5IK90A-SW2T

3.3 kg (7.3 lb.)

A334

0

0

200 W (1/4 HP)

37 (1.46) 2 (0.08)

ϕ83−0.035 (ϕ3.2677−0.0014)

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

2)

± 0.0

.5

0 104±

□90 (□3.54)

90 W (1/8 HP)

◇ Shaft Section of Round Shaft Type

ϕ12−0.018 (ϕ0.4724−0.0007)

60 W (1/12 HP)

28.58±0.2 (1.125±0.008)

0 (0.1875−0.0012 )

0

40 W (1/19 HP)

4.763−0.03

(The key is included with the gearhead)

(4.09

Protective Earth Terminal M4 (Lead wire type only)

5 (0.20) max.

4×ϕ6.5 (ϕ0.256) Thru 22.5˚

A-56

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-54

Standard AC Motors

◇ Conduit Box Type ③ Motor Model 5IK90GE-FCH 5IK90GE-ECH

Gearhead Model

DXF

5GE□SA

A906U

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 3.7 kg (8.1 lb.) Gearhead 1.5 kg (3.3 lb.) 74 (2.91) ϕ21.5

100 (3.94)

(ϕ0.846)

Introduction

ϕ15.875−00.011 ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

90 (3.54)

☐90 (☐3.54)

0.5 ) 4± .02 10 9± 0 0 ( 4.

7 (0.28) 65 (2.56) 38 (1.50)

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

◇ Key and Key Slot

+0.1 0

(0.108+00.004)

4.763 0 (0.1875+0.0016 ) 0

Gearhead Model 5GE□SA

DXF A907U

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

Motor Model 5IK90GE-SH

2.743

0

0 (0.1875−0.0012 )

4.763−0.03

+0.040

0

4.763−0.03 0 (0.1875−0.0012 )

Clutch & Brake Motors

28.58±0.2 (1.125±0.008)

V Series

(The key is included with the gearhead)

● Enter the gear ratio in the box (□) within the model name.

Mass: Motor 3.3 kg (7.3 lb.) Gearhead 1.5 kg (3.3 lb.) ϕ21.5 (ϕ0.846)

54 (2.13)

ϕ15.875−00.011

75 (2.95)

0

☐90 (☐3.54)

+0.1 0

(0.108+00.004)

2.743

0

0 (0.1875−0.0012 )

4.763−0.03

+0.040

4.763 0 (0.1875+0.0016 ) 0

Brake Pack

0

90 (3.54)

45 (1.77) 23 (0.91)

(The key is included with the gearhead)

4.763−0.03 0 (0.1875−0.0012 )

4×ϕ6.5 (ϕ0.256) Thru 90 (3.54)

Linear Heads

◇ Key and Key Slot

0.5 ) 4± .02 10 9± 0 0 ( 4.

Right-Angle Gearheads

135 (5.31)

7 (0.28) 65 (2.56) 38 (1.50)

Torque Motors

No.10-24UNC×10 (0.39) Deep 7.5 (0.30)

28.58±0.2 (1.125±0.008)

ϕ17 (ϕ0.67) 18 (0.71) ϕ34 (ϕ1.34)

ϕ0.6250−0.0004 (5/8") 29.5±0.5 (1.16±0.02) 28.58 (1.13)

3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18 ●Details of terminal box ➜ Page A-314

Electromagnetic Brake Motors

7.5 (0.30) 135 (5.31)

3 Motor Leads: UL Style 3266, AWG20 1 Ground Lead: UL Style 3266, AWG18 ●Details of terminal box ➜ Page A-314

Reversible Motors

No.10-24UNC×10 (0.39) Deep

Induction Motors

29.5±0.5 (1.16±0.02) 28.58 (1.13)

31 (1.22)

65 (2.56)

0

ϕ0.6250−0.0004 (5/8")

Accessories Installation

Product Line A-54 / Dimensions A-55 / Connection Diagrams A-59

A-57

Standard AC Motors

◇ Shaft Section of Round Shaft Type

◇ Shaft Section of Round Shaft Type

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

The motor’s dimensions (excluding the shaft section) are the same as those of the pinion shaft types.

Motor Model

Mass

5IK90A-FCH 5IK90A-ECH

DXF

3.7 kg (8.1 lb.)

Motor Model 5IK90A-SH

A815

Mass

DXF

3.3 kg (7.3 lb.)

A816

74 (2.91)

(

0 (ϕ0.4724−0.0007 )

25 W (1/30 HP)

4×ϕ6.5 (ϕ0.256) Thru

± 0. ) 104 9± 0.02 0 . (4

90 (3.54)

0

0 ϕ83−0.035

(ϕ3.2677−0.0014)

30 (1.18)

11(0.43)

± 0.5

104 ±0.02) 9 (4.0

90 (3.54)

15 W (1/50 HP)

0 ϕ83−0.035

30 (1.18)

)

0 ϕ12−0.018

2 (0.08)

5

11 (0.43)

6W (1/125 HP)

0 ϕ0.4724−0.0007

2 (0.08)

37 (1.46)

65 (2.56)

0 ϕ12−0.018

0 (ϕ3.2677−0.0014 )

1 W, 3 W (1/750 HP, 1/250 HP)

37 (1.46)

4×ϕ6.5 (ϕ0.256) Thru

90 (3.54)

90 (3.54)

◇ Decimal Gearhead Can be connected to GE pinion shaft type.

A029

40 (1.57) 21 2 (0.83) (0.08)

0

ϕ83−0.035

90 W (1/8 HP) 200 W (1/4 HP)

□90 (□3.54)

0.5

104± ) 0.02 (4.09±

4×ϕ10.8 (ϕ0.425) Thru

A

◇ Capacitor Dimensions

Unit = mm (in.)

Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Lead Wire Type

Capacitor Model

A

B

C

Mass g (oz.)

Capacitor Cap

Terminal Box Type

5IK90GE-AW2U (5IK90A-AW2U)

5IK90GE-AW2TU (5IK90A-AW2TU)

CH200CFAUL2

58 29 41 (2.28) (1.14) (1.61)

91 (3.2)

5IK90GE-CW2E (5IK90A-CW2E)

5IK90GE-CW2TE (5IK90A-CW2TE)

CH60BFAUL

58 29 41 (2.28) (1.14) (1.61)

92 (3.2)

Included

6 (0.24)

R (R 10 0.3 9)

4 (0.16)

C

AMP#187

10 (0.39)

ϕ4.3 20 (ϕ0.169) ( 0.79)

7 (0.28)

B

2-Pole 40-150 W (1/19-1/5 HP)

◇ Capacitor (Included with single-phase motors) B+15 (0.59)

60 W (1/12 HP)

61 (2.40)

0 (ϕ3.2677−0.0014 )

40 W (1/19 HP)

5GE10XS Mass: 0.6 kg (1.32 lb.)

A-58

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-54

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Connection diagrams are also valid for the equivalent round shaft type. Lead Wire Type

Terminal Box Type

Clockwise

5IK90GE-SW2 Clockwise

CW White

White

L2(S)

PE

Black

N

Red

L1(R) Motor

Clockwise

CW

Motor

PE

Black

L3(T)

Capacitor

Counterclockwise CCW

Capacitor

PE

Motor

PE

N

U V W

Motor

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

PE

V Series

Capacitor

Capacitor

Z2 U2 U1

L1(R) L2(S) L3(T)

CW

PE

CCW

L Motor

Black

N

Z2 U2 U1

Clockwise

Electromagnetic Brake Motors

Red

L N

Counterclockwise

White

L

CW

Reversible Motors

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

5IK90GE-SW2T

Induction Motors

Red

L

5IK90GE-AW2TU 5IK90GE-CW2TE

Introduction

5IK90GE-AW2U 5IK90GE-CW2E

Standard AC Motors

■ Connection Diagrams

Conduit Box Type

Clockwise

N

White Red Black

5IK40GN-SW2T 5IK90GE-SH Clockwise L1(R) L2(S)

Motor

L3(T)

NC✽ N

White Red Black

Motor

PE

PE ✽NC: No connection

L

Red White Black Green/Yellow

Green/Yellow

Counterclockwise

CW

CCW

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

Motor

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

NC✽ L

CW

Clutch & Brake Motors

5IK90GE-FCH 5IK40GN-AW2T□ 5IK90GE-ECH 5IK40GN-CW2T□

Green/Yellow Torque Motors

PE ✽NC: No connection

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

Linear Heads

● How to connect a capacitor ➜ Page A-313

Right-Angle Gearheads

PE: Protective Earth

Gearhead, Accessories and Peripheral Equipment Instantaneous Stop Brake Pack ➜Page A-277

Speed Control Speed Controller ➜Page B-156

Accessories ➜Page A-287

Brake Pack

Space-Saving Right-Angle Gearheads ➜Page A-239

Accessories Installation

Product Line A-54 / Dimensions A-55 / Connection Diagrams A-59

A-59

Standard AC Motors

High Power Induction Motors BH Series

200 W (1/4 HP)

Frame Size: □104 mm (□4.09 in.) Cable Type Right-Angle Hollow Shaft

Terminal Box Type Parallel Shaft

1 W, 3 W (1/750 HP, 1/250 HP)

■ Features

6W (1/125 HP)

● High Power 200 W (1/4 HP)

● "Combination Type" for Easy Installation

Smallest frame size among 200 W (1/4 HP) motors

The combination type comes with the motor and gearhead pre-assembled. This enables easy installation in equipment.

● Hypoid Gear-Employed Right-Angle Gearheads

15 W (1/50 HP)

Right-angle gearheads employ hypoid gears. Hollow shafts and solid shafts are available to enable space-saving.

●

Combination Type: The combination type comes with the motor and its dedicated gearhead pre-assembled, which simplifies installation in equipment. Motors and gearheads are also available separately to facilitate changes or repairs.

RoHS-Compliant

The BH Series conforms to the RoHS Directive that prohibits the use of six chemical substances including lead and cadmium.

25 W (1/30 HP)

● Details of RoHS Directive ➜ Page G-38

■ Specifications – Continuous Rating

40 W (1/19 HP)

Model Combination Type ( ) : Round Shaft Type Cable Type

Output Power

Terminal Box Type

60 W (1/12 HP) 90 W (1/8 HP)

BHI62F-□RH BHI62F-□RA BHI62F-□ (BHI62F-A)

BHI62FT-□RH BHI62FT-□RA BHI62FT-□ (BHI62FT-A)

BHI62E-□RH BHI62E-□RA BHI62E-□ (BHI62E-A)

BHI62ET-□RH BHI62ET-□RA BHI62ET-□ (BHI62ET-A)

W HP 200 1/4

Voltage

Frequency

VAC

Hz

Rated Speed

Capacitor

r/min

μF

1.27 180

1500

40

1.27 180

1500

1.52 210

1250

1.27 180

1500

1.49 210

1.49 210

1250

60

1.25 177

1.25 177

1500

Three-Phase 220

60

1.23 174

1.23 174

1550

Three-Phase 230

60

1.18 167

1.18 167

1600

A

Single-Phase 110 60

3

Single-Phase 115 Single-Phase 220

200 1/4

Current Starting Torque Rated Torque N·m oz-in 0.88 124 0.98 139

60 50

1.5

Single-Phase 230

0.98 139

60 200 W (1/4 HP)

50

2-Pole 40-150 W (1/19-1/5 HP)

BHI62ST-□RH BHI62ST-□RA BHI62ST-□ (BHI62ST-A)

−

Three-Phase 200 200 1/4

1.1

0.95

N·m oz-in

10

−

● Enter the gear ratio in the box (□) within the model name. The values for each specification applies to the motor only. ● Details of safety standards ➜ Page G-2 ● List of safety standard approved products (Model, Standards, Standards File No., Certification Body) ➜ Page G-11 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

■ Product Line ● Combination Type ◇ Right-Angle Shaft Type Hollow Shaft Cable Hollow Shaft Terminal Box Solid Shaft Cable Solid Shaft Terminal Box

Voltage Single-Phase 110/115 VAC Single-Phase 220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC

Model BHI62F-□RH BHI62E-□RH BHI62FT-□RH BHI62ET-□RH BHI62ST-□RH BHI62F-□RA BHI62E-□RA BHI62FT-□RA BHI62ET-□RA BHI62ST-□RA

Gear Ratio

5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

● Enter the gear ratio in the box (□) within the model name. The following items are included in each product. Motor, Gearhead, Capacitor✽, Capacitor Cap✽, Parallel Key, Operating Manual ✽ Only for single-phase motors

A-60

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-60 / System Configuration A-23 / Specifications A-60 / Product Line A-60

Type Parallel Shaft Cable Parallel Shaft Terminal Box

Standard AC Motors

● Round Shaft Type

◇ Parallel Shaft Voltage Single-Phase 110/115 VAC Single-Phase 220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC

Model BHI62F-□ BHI62E-□ BHI62FT-□ BHI62ET-□ BHI62ST-□

Type

Gear Ratio

Cable

3, 3.6, 5, 6, 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180

Terminal Box

Model BHI62F-A BHI62E-A BHI62FT-A BHI62ET-A BHI62ST-A

Introduction

● Enter the gear ratio in the box (□) within the model name.

Voltage Single-Phase 110/115 VAC Single-Phase 220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors

The following items are included in each product. Motor, Gearhead, Capacitor✽, Capacitor Cap✽, Mounting Screws, Parallel Key, Operating Manual ✽ Only for single-phase motors

Induction Motors

■ Gearmotor – Torque Table for Combination Type

Unit = Upper values: N·m/Lower values: lb-in

Model

300

250

200

167

120

100

83

60

50

42

30

25

20

17

15

12.5

10

8.3

6

7.5

9

18

25

30

36

50

60

75

90

100 120 150 180

5.5 48

6.7 59

8.3 73

10.0 88

13.9 123

16.6 146

20.0 177

27.7 240

33.3 290

36.0 310

40.0 350

43.0 380

47.0 410

51.5 450

54.5 480

60 530

60 530

60 530

BHI62ST-□RH, BHI62ST-□RA

5.4 47

6.5 57

8.2 72

9.8 86

13.6 120

16.3 144

19.6 173

27.2 240

32.6 280

36.0 310

40.0 350

43.0 380

47.0 410

51.5 450

54.5 480

60 530

60 530

60 530

Gear Ratio

12.5 15

Unit = Upper values: N·m/Lower values: lb-in

Speed r/min

Model

360

300

240

200

144

120

100

72

60

50

36

30

24

20

18

15

12

10

5

6

7.5

9

18

25

30

36

50

60

75

90

100 120 150 180

■-□RH, BHI62F □ ■-□RA BHI62F □ ■-□RH, BHI62E □ ■-□RA BHI62E □

4.6 40

5.6 49

7.0 61

8.3 73

11.6 102

13.9 123

16.7 147

23.2 200

27.8 240

33.4 290

40.0 350

43.0 380

47.0 410

51.5 450

54.5 480

60 530

60 530

60 530

BHI62ST-□RH, BHI62ST-□RA (200 VAC)

4.6 40

5.5 48

6.8 60

8.2 72

11.4 100

13.7 121

16.4 145

22.8 200

27.4 240

32.9 290

40.0 350

43.0 380

47.0 410

51.5 450

54.5 480

60 530

60 530

60 530

BHI62ST-□RH, BHI62ST-□RA (220 VAC)

4.5 39

5.4 47

6.7 59

8.1 71

11.2 99

13.5 119

16.2 143

22.4 198

26.9 230

32.3 280

40.0 350

43.0 380

47.0 410

51.5 450

54.5 480

60 530

60 530

60 530

BHI62ST-□RH, BHI62ST-□RA (230 VAC)

4.3 38

5.2 46

6.5 57

7.8 69

10.8 95

12.9 114

15.5 137

21.5 190

25.8 220

31.0 270

40.0 350

43.0 380

47.0 410

51.5 450

54.5 480

60 530

60 530

60 530

Gear Ratio

12.5 15

Unit = Upper values: N·m/Lower values: lb-in

500

417

300

250

200

167

Gear Ratio

3

3.6

5

6

7.5

9

■-□ BHI62E □

4.1 36

4.9 43

6.8 60

8.2 72

10.3 91

BHI62ST-□

4.0 35

4.8 42

6.7 59

8.0 70

10.1 89

100

83

60

50

42

30

25

20

17

12.5 15

120

18

25

30

36

50

60

75

90

12.3 108

16.3 144

19.6 173

23.5 200

32.7 280

39.2 340

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

12.1 107

16.0 141

19.2 169

23.1 200

32.0 280

38.4 330

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

10

8.3

Unit = Upper values: N·m/Lower values: lb-in

Speed r/min

Model

12.5

600

500

360

300

240

200

144

120

100

72

60

50

36

30

24

20

18

15

12

10

5

6

7.5

9

12.5 15

18

25

30

36

50

60

75

90

■-□, BHI62E □ ■-□ BHI62F □

4.1 36

5.7 50

6.9 61

8.6 76

10.3 91

13.7 121

16.4 145

19.7 174

27.3 240

32.8 290

39.3 340

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

BHI62ST-□ (200 VAC)

3.4 30

4.1 36

5.6 49

6.8 60

8.4 74

10.1 89

13.4 118

16.1 142

19.4 171

26.9 230

32.3 280

38.7 340

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

BHI62ST-□ (220 VAC)

3.3 29

4.0 35

5.5 48

6.6 58

8.3 73

10.0 88

13.2 116

15.9 140

19.0 168

26.4 230

31.7 280

38.1 330

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

BHI62ST-□ (230 VAC)

3.2 28

3.8 33

5.3 46

6.4 56

8.0 70

9.6 84

12.7 112

15.2 134

18.3 161

25.4 220

30.4 260

36.5 320

40 350

40 350

40 350

40 350

40 350

40 350

40 350

40 350

100 120 150 180

Accessories

3.6

Brake Pack

3 3.4 30

Gear Ratio

Linear Heads

● Parallel Shaft 60 Hz

15

100 120 150 180 Right-Angle Gearheads

Speed r/min

Model

Torque Motors

● Parallel Shaft 50 Hz

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

● Right-Angle Shaft 60 Hz

Clutch & Brake Motors

5

■-□RH, BHI62E □ ■-□RA BHI62E □

V Series

Speed r/min

Electromagnetic Brake Motors

● Right-Angle Shaft 50 Hz

Reversible Motors

□) within the model name. ● Enter the code that represents the terminal box type “T” in the box (■ ● Enter the gear ratio in the box (□) within the model name. ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite ● A colored background ( direction. ● The speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2∼20% less than the displayed value, depending on the load. ● Decimal gearheads are not available for the BH series.

Installation

Dimensions A-62 / Connection Diagrams A-69 / Motor and Gearhead Combinations A-71

A-61

Standard AC Motors

■ Permissible Overhung Load and Permissible Thrust Load Combination Type ➜ Page A-16 Round Shaft Type ➜ Page A-16

■ Permissible Load Inertia J of Gearhead ➜ Page A-17

Unit = mm (in.)

● Mounting screws are included with the combination type, parallel shaft. Dimensions for mounting screws ➜ Page A-310

8−0.036

0

A299

0

25−0.2 0 (0.984−0.008 )

25 W (1/30 HP) 40 W (1/19 HP)

109.3 (4.30) 30 (1.18) 15 (0.59) 1.5 (0.06)

4 (0.16)

60 W (1/12 HP) 90 W (1/8 HP)

ϕ40 (ϕ1.57)

200 W (1/4 HP)

32.5 (1.28)

0

0 (0.2756−0.0014 )

25

+0.04 0 +0.0016 0.31 0

+0.033 0

Groove for Retaining Ring ϕ26.2

+0.21 0

(ϕ1.03+0.008 ) 0

A−A

(0.9843+0.0013 ) 0

.5 ±0

)

30 (1.18) 15 (0.59) 1.5 (0.06)

Flange Mounting Surface

0 (ϕ2.2835−0.0018 )

8

(

4.8 (0.19)

ϕ58−0.046

102 (4.02)

Motor Cable ϕ7.8 (ϕ0.31), 500 mm (20 in.) Length UL Style 3271, AWG20

0

7−0.036

154 (6.06)

□103 (□4.06)

160 (6.30)

0 (0.3150−0.0014 )

(The key is included with the gearhead)

) .02

0 0 12 .72± (4

14 (0.55)

15 W (1/50 HP)

◇Key

BHI62F-□RH, BHI62E-□RH Mass: 10.0 kg (22 lb.) Motor: BHI62F-G2, BHI62E-G2 Gearhead: BH6G2-□RH

27 (1.06)

2-Pole 40-150 W (1/19-1/5 HP)

28.3 (1.11)

A 104 (4.09)

6W (1/125 HP)

◇ Combination Type: Right-Angle, Hollow Shaft (Cable Type)

16 (0.63) 99 (3.90) 118 (4.65)

1 W, 3 W (1/750 HP, 1/250 HP)

■ Dimensions

A 104 (4.09)

4×ϕ8.5 (ϕ0.335) Thru

66 (2.60)

● Enter the gear ratio in the box (□) within the model name.

A-62

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-60 / System Configuration A-23 / Specifications A-60 / Product Line A-60

Standard AC Motors

◇ Combination Type: Right-Angle, Solid Shaft (Cable Type) BHI62F-□RA, BHI62E-□RA Mass: 10.0 kg (22 lb.) Motor: BHI62F-G2, BHI62E-G2 Gearhead: BH6G2-□RA A300 154 (6.06)

4 (0.16) 48 (1.89)

0

0.5

) 02

4×ϕ8.5 (ϕ0.335) Thru

0

32±0.2 (1.260±0.008)

(0.2362−00.0012)

6−0.03

◇Key and Key Slot

0

0

6−0.03 0 (0.2362−0.0012 )

18.5−0.1

(0.728−00.004)

Torque Motors

● At the time of shipment, a key is inserted on the gearhead’s shaft.

66 (2.60)

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

104 (4.09)

Clutch & Brake Motors

104 (4.09)

0± 0. 12 .72± (4

27 (1.06)

V Series

32.5 (1.28)

14 (0.55)

40±0.5 (1.57±0.02)

32 (1.26)

ϕ58−0.046 (ϕ2.2835−0.0018)

Electromagnetic Brake Motors

0

0

Motor Cable ϕ7.8 (ϕ0.31), 500 mm (20 in.) Length UL Style 3271, AWG20

Reversible Motors

102 (4.02)

ϕ22−0.021 (ϕ0.8661−0.0008) 24.5 (0.96) 0

Induction Motors

16 (0.63) 99 (3.90) 118 (4.65)

Introduction

□103 (□4.06)

160 (6.30)

Right-Angle Gearheads Linear Heads Brake Pack Accessories Installation

● Enter the gear ratio in the box (□) within the model name.

Dimensions A-62 / Connection Diagrams A-69 / Motor and Gearhead Combinations A-71

A-63

(The key is included with the gearhead)

8−0.036

0

0

25−0.2

A301

0 (0.984−0.008 )

109.3 (4.30) 30 (1.18) 15 (0.59) 1.5 (0.06)

0

7−0.036 0 (0.2756−0.0014 )

30 (1.18) 15 (0.59) 1.5 (0.06)

16 (0.63) 99 (3.90) 118 (4.65)

15 W (1/50 HP)

ϕ40 (ϕ1.57)

4.8 (0.19)

25 W (1/30 HP)

0 ϕ58−0.046

75 (2.95)

9 (0.35)

40 W (1/19 HP)

25 +0.04 0 +0.0016 0.31 0

8

(

(ϕ1.03+0.008 ) 0

A−A

+0.033 0

62 (2.44)

(0.9843+0.0013 ) 0 0.5

2)

0± 0.0 12 .72± (4

)

+0.21 0

Flange Mounting Surface

(ϕ2.2835−00.0018) 28 (1.10) max.

Groove for Retaining Ring ϕ26.2

43 (1.69)

6W (1/125 HP)

102 (4.02)

4 (0.16)

1 W, 3 W (1/750 HP, 1/250 HP)

154 (6.06)

160 (6.30)

0 (0.3150−0.0014 )

◇Key

BHI62FT-□RH, BHI62ET-□RH, BHI62ST-□RH Mass: 10.0 kg (22 lb.) Motor: BHI62FT-G2, BHI62ET-G2, BHI62ST-G2 Gearhead: BH6G2-□RH

□103 (□4.06)

Standard AC Motors

◇ Combination Type: Right-Angle, Hollow Shaft (Terminal Box Type)

28.3 (1.11) 104 (4.09)

60 W (1/12 HP)

A

90 W (1/8 HP)

A 104 (4.09)

200 W (1/4 HP)

4×ϕ8.5 (ϕ0.335) Thru

66 (2.60)

● Use cable with a diameter of ϕ6∼ϕ12 mm (ϕ0.24∼ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

2-Pole 40-150 W (1/19-1/5 HP)

● Enter the gear ratio in the box (□) within the model name.

A-64

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-60 / System Configuration A-23 / Specifications A-60 / Product Line A-60

Standard AC Motors

◇ Combination Type: Right-Angle, Solid Shaft (Terminal Box Type) BHI62FT-□RA, BHI62ET-□RA, BHI62ST-□RA Mass: 10.0 kg (22 lb.) Motor: BHI62FT-G2, BHI62ET-G2, BHI62ST-G2 Gearhead: BH6G2-□RA A302 160 (6.30)

40±0.5 (1.57±0.02)

0

0.5

43 (1.69)

62 (2.44)

9 (0.35)

75 (2.95)

2)

0± 0.0 12 .72± (4

4×ϕ8.5 (ϕ0.335) Thru

0

(0.2362−00.0012)

32±0.2 (1.260±0.008)

0

0

6−0.03 0 (0.2362−0.0012 )

18.5−0.1

(0.728−00.004)

Right-Angle Gearheads

● At the time of shipment, a key is inserted on the gearhead’s shaft.

Torque Motors

6−0.03

◇Key and Key Slot

66 (2.60)

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

104 (4.09)

Clutch & Brake Motors

104 (4.09) ● Use cable with a diameter of ϕ6∼ϕ12 mm (ϕ0.24∼ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

V Series

28 (1.10) max.

4 (0.16) 48 (1.89)

32 (1.26)

ϕ58−0.046 (ϕ2.2835−0.0018)

Electromagnetic Brake Motors

0

0

Reversible Motors

102 (4.02)

ϕ22−0.021 (ϕ0.8661−0.0008) 24.5 (0.96) 0

Induction Motors

16 (0.63) 99 (3.90) 118 (4.65)

Introduction

□103 (□4.06)

154 (6.06)

Linear Heads Brake Pack Accessories Installation

● Enter the gear ratio in the box (□) within the model name.

Dimensions A-62 / Connection Diagrams A-69 / Motor and Gearhead Combinations A-71

A-65

BHI62F-□, BHI62E-□ Mass: 8.0 kg (18 lb.) Motor: BHI62F-G2, BHI62E-G2 Gearhead: BH6G2-□ A303 72 (2.83) 42 (1.65) 5 (0.20) 33.5±0.5 (1.32±0.02) 0 ϕ18−0.018 25 (ϕ0.7087−00.0007) (0.98)

160 (6.30) 10.5 (0.41)

104 (4.09) 4×ϕ8.5 (ϕ0.335) Thru

15 W (1/50 HP)

104 (4.09)

20 (0.79) 32.5 (1.28)

.5 ±0 ) 120 2±0.02 7 (4.

14 (0.55)

6W (1/125 HP)

□103 (□4.06)

ϕ42 (ϕ1.65)

1 W, 3 W (1/750 HP, 1/250 HP)

Motor Cable ϕ7.8 (ϕ0.31), 500 mm (20 in.) Length UL Style 3271, AWG20

20.5 (0.81)

Standard AC Motors

◇ Combination Type: Parallel Shaft (Terminal Box Type)

27 (1.06)

25 W (1/30 HP) 40 W (1/19 HP)

BHI62FT-□, BHI62ET-□, BHI62ST-□ Mass: 8.0 kg (18 lb.) Motor: BHI62FT-G2, BHI62ET-G2, BHI62ST-G2 Gearhead: BH6G2-□ A304 28 (1.10) max.

75 (2.95)

9 (0.35)

62 (2.44) 0

(ϕ0.7087−00.0007)

200 W (1/4 HP)

20 (0.79)

90 W (1/8 HP)

□103 (□4.06)

25 (0.98)

10.5 (0.41) 160 (6.30)

5 (0.20) 72 (2.83) 42 (1.65)

104 (4.09)

20.5 (0.81) ϕ42 (ϕ1.65)

60 W (1/12 HP)

33.5±0.5 (1.32±0.02)

43 (1.69)

ϕ18−0.018

.5 ±0 ) 120 2±0.02 (4.7

● Use cable with a diameter of ϕ6∼ϕ12 mm (ϕ0.24∼ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

0

6−0.03

(0.2362−00.0012)

0 (0.571−0.004 )

0

14.5−0.1

0

25±0.2 (0.984±0.008)

(0.2362−00.0012)

◇Key and Key Slot

6−0.03

2-Pole 40-150 W (1/19-1/5 HP)

104 (4.09) 4×ϕ8.5 (ϕ0.335) Thru

● At the time of shipment, a key is inserted on the gearhead’s shaft.

● Enter the gear ratio in the box (□) within the model name.

A-66

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-60 / System Configuration A-23 / Specifications A-60 / Product Line A-60

Standard AC Motors

◇ Round Shaft Type (Cable Type) BHI62F-A, BHI62E-A Mass: 5.0 kg (11 lb.) A307 0

ϕ14−0.018

(ϕ0.5512−00.0007)

104 (4.09)

0

□103 (□4.06)

13 (0.51) 14 (0.55)

Reversible Motors

32.5 (1.28)

0.5

120± ±0.02) (4.72

Induction Motors

Motor Cable ϕ7.8 (ϕ0.31), 500 mm (20 in.) Length UL Style 3271, AWG20

4×ϕ8.5 (ϕ0.335) Thru

27 (1.06)

Electromagnetic Brake Motors

◇ Round Shaft Type (Terminal Box Type) BHI62FT-A, BHI62ET-A, BHI62ST-A Mass: 5.0 kg (11 lb.) A308 62 (2.44)

9 (0.35)

10.5 (0.41) 160 (6.30)

0.5

120± ±0.02) (4.72

□104 (□4.09)

0 (ϕ3.7008−0.0014 )

0

ϕ94−0.035

13 (0.51)

(ϕ0.5512−00.0007)

2 (0.08) 37 (1.46)

● Use cable with a diameter of ϕ6∼ϕ12 mm (ϕ0.24∼ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

4×ϕ8.5 (ϕ0.335) Thru

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

□103 (□4.06)

30 (1.18)

0

ϕ14−0.018

Clutch & Brake Motors

43 (1.69)

75 (2.95)

V Series

28 (1.10) max.

Introduction

30 (1.18)

(ϕ3.7008−00.0014)

10.5 (0.41)

37 (1.46) 2 (0.08)

ϕ94−0.035

160 (6.30)

Torque Motors Right-Angle Gearheads Linear Heads Brake Pack Accessories Installation

Dimensions A-62 / Connection Diagrams A-69 / Motor and Gearhead Combinations A-71

A-67

1 W, 3 W (1/750 HP, 1/250 HP)

B+15 (0.59)

B

AMP#187

7 (0.28)

ϕ4.3 20 (ϕ0.169) ( 0.79)

◇ Capacitor Dimensions

Unit = mm (in.)

Model Cable Type Terminal Box Type

A

10 (0.39)

Standard AC Motors

◇ Capacitor (Included with single-phase motors)

6 (0.24)

Capacitor Model

A

B

C

BHI62F-□RH BHI62F-□RA BHI62F-□ BHI62F-A

BHI62FT-□RH BHI62FT-□RA 58 41 58 CH400CFAUL2 BHI62FT-□ (2.28) (1.61) (2.28) BHI62FT-A

BHI62E-□RH BHI62E-□RA BHI62E-□ BHI62E-A

BHI62ET-□RH BHI62ET-□RA BHI62ET-□ BHI62ET-A

Mass g (oz.)

Capacitor Cap

175 (6.2) Included

CH100BFAUL

58 35 50 (2.28) (1.38) (1.97)

132 (4.7)

● Enter the gear ratio in the box (□) within the model name.

15 W (1/50 HP)

4 (0.16)

C

6W (1/125 HP)

R (R 10 0.3 9)

■ Mounting Method for Right-Angle, Hollow Shaft Types

25 W (1/30 HP) 40 W (1/19 HP) 60 W (1/12 HP)

These figures below show how to mount loads depending on the shape of the shaft. The tolerance of the inner diameter for the hollow shaft is finished as shown in the table on the right, and “key slot” processing is given to mount the load shaft. Use the key provided with the product by fastening it to the shaft. Apply a coating of molybdenum disulfide or similar grease to the surface of the load shaft and to the inner diameter of the load shaft to prevent sticking. Recommended load shaft diameter and inner diameter of hollow shaft are shown in the table on the right.

● Inner Diameter of Hollow Shaft and Recommended Load Shaft Diameter

● Stepped Load Shaft

● Straight Load Shaft

Hollow Shaft 90 W (1/8 HP)

Load Shaft

Spacer

Unit = mm (in.)

Model Inner Diameter of Hollow Shaft H8 Recommended Load Shaft Diameter h7

● Enter the gear ratio in the box (□) within the model name.

Hollow Shaft Load Shaft

Flat Washer

Spacer Flat Washer Bolt

Bolt 200 W (1/4 HP)

Spring Washer

Spring Washer

Retaining Ring for Hole Spacer

Retaining Ring for Hole 2-Pole 40-150 W (1/19-1/5 HP)

A-68

BH6G2-□RH ϕ25 + 0.033 (ϕ0.9843+ 0.0013 ) 0 0 0 0 ) ϕ25 − 0.021 (ϕ0.9843− 0.0008

● After securing a load, attach the safety cover included. Notes: ● Be careful not to apply a shock to the hollow shaft when mounting a load shaft. It may damage the bearing inside the gearhead. ● Bolts or other fasteners used to install the load shaft are not included. These parts must be purchased separately.

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-60 / System Configuration A-23 / Specifications A-60 / Product Line A-60

● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. ● Enter the voltage (F, E) in the box (□) within the model name. Motor Type

Cable Type

Single-Phase Induction Motor Terminal Box Type✽

Clockwise

CW

BHI62□T-3∼9 BHI62□T-50∼180 Clockwise

CW

BHI62ST-3∼9 BHI62ST-50∼180 Clockwise

CW

Motor

Black

N

CCW

Counterclockwise

Z2 U2 U1

Capacitor

PE

Counterclockwise

L1(R) L2(S) L3(T)

Motor

U V W

Motor

Reversible Motors

Capacitor

L N

PE

Counterclockwise

CCW

White Red

Capacitor

Combination Type: Parallel Shaft

Capacitor

Clockwise

Clockwise

CW

BHI62ST-12.5∼36 Clockwise

White Red

N

BHI62□T-12.5∼36

L Motor

Black

N

Capacitor

Capacitor

Counterclockwise

Counterclockwise

CCW

Z2 U2 U1

L1(S) L2(R) L3(T)

Motor

CW

U V W

Motor

PE

PE

Counterclockwise

CCW

To change the rotation direction, change any two connections between L1(S), L2(R) and L3(T). White L

Black

Capacitor

Motor

L N

Z2 U2 U1

Capacitor

PE

Motor

Linear Heads

Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

Right-Angle Gearheads

PE: Protective Earth ✽ Connecting to the terminal Applicable lead wires: AWG24∼12 Strip length: 8 mm (0.315 in.)

Torque Motors

N

Red

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

L

CW

PE

Clutch & Brake Motors

BHI62□-12.5∼36

Motor V Series

N

Black

N

Z2 U2 U1

L Motor

Electromagnetic Brake Motors

To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T). L

Induction Motors

White Red

L

Introduction

BHI62□-3∼9 BHI62□-50∼180

Three-Phase Induction Motor Terminal Box Type✽

Standard AC Motors

■ Connection Diagrams

● How to connect a capacitor ➜ Page A-313 Brake Pack Accessories Installation

Dimensions A-62 / Connection Diagrams A-69 / Motor and Gearhead Combinations A-71

A-69

Standard AC Motors

Motor Type

Single-Phase Induction Motor Terminal Box Type✽

Cable Type

BHI62□-5RH∼180RH BHI62□-5RA∼180RA CW

Clockwise

BHI62□T-5RH∼180RH BHI62□T-5RA∼180RA Clockwise

CW

BHI62ST-5RH∼180RH BHI62ST-5RA∼180RA Clockwise

CW

1 W, 3 W (1/750 HP, 1/250 HP)

White

L

Red

Z2 U2 U1

L

Motor

Black

N

6W (1/125 HP)

Combination Type: Right Angle Shaft

Three-Phase Induction Motor Terminal Box Type✽

N

Capacitor

Capacitor CCW

Counterclockwise

Motor

L1(S) L2(R) L3(T)

U V W

PE

Counterclockwise

Motor

PE

Counterclockwise

CCW

15 W (1/50 HP)

To change the rotation direction, change any two connections between L1(S), L2(R) and L3(T). White Red

L N

25 W (1/30 HP)

L N

Z2 U2 U1

Capacitor

PE

Motor

Black

Capacitor

BHI62□-A

Motor

BHI62□T-A

40 W (1/19 HP)

Clockwise

CW

BHI62ST-A

Clockwise

CW

Clockwise

CW

White

60 W (1/12 HP)

L N

Round Shaft Type

Red

Motor

Black

Capacitor

90 W (1/8 HP)

Counterclockwise L

CCW

Z2 U2 U1

Capacitor

PE

Counterclockwise

Motor

L Motor

CCW

200 W (1/4 HP)

Black

Capacitor

N Capacitor

Z2 U2 U1

L1(R) L2(S) L3(T)

U V W

Motor

PE

White Red

N

L N

Motor

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

PE

2-Pole 40-150 W (1/19-1/5 HP)

PE: Protective Earth ✽ Connecting to the terminal Applicable lead wires: AWG24∼12 Strip length: 8 mm (0.315 in.) Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay. ● How to connect a capacitor ➜ Page A-313

A-70

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-60 / System Configuration A-23 / Specifications A-60 / Product Line A-60

● Combination Type: Right Angle Shaft Motor Model BHI62F-G2 BHI62FT-G2 BHI62E-G2

BHI62ST-G2

● Combination Type: Parallel Shaft Model BHI62F-□ BHI62FT-□ BHI62E-□ BHI62ET-□ BHI62ST-□

Motor Model BHI62F-G2 BHI62FT-G2 BHI62E-G2 BHI62ET-G2 BHI62ST-G2

Gearhead Model

BH6G2-□

● Enter the gear ratio in the box (□) within the model name.

Induction Motors

BHI62ET-G2

Gearhead Model BH6G2-□RH BH6G2-□RA BH6G2-□RH BH6G2-□RA BH6G2-□RH BH6G2-□RA BH6G2-□RH BH6G2-□RA BH6G2-□RH BH6G2-□RA

Introduction

Model BHI62F-□RH BHI62F-□RA BHI62FT-□RH BHI62FT-□RA BHI62E-□RH BHI62E-□RA BHI62ET-□RH BHI62ET-□RA BHI62ST-□RH BHI62ST-□RA

Standard AC Motors

■ List of Motor and Gearhead Combinations Motor and gearhead combinations are shown below.

● Enter the gear ratio in the box (□) within the model name.

Accessories ➜Page A-287

Electromagnetic Brake Motors

Speed Control Speed Controller ➜Page B-156

Reversible Motors

Accessories and Peripheral Equipment

V Series Clutch & Brake Motors Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors Torque Motors Right-Angle Gearheads Linear Heads Brake Pack Accessories Installation

Dimensions A-62 / Connection Diagrams A-69 / Motor and Gearhead Combinations A-71

A-71

Standard AC Motors

Induction Motors 2-Pole, High-Speed Type

40 W (1/19 HP), 60 W (1/12 HP), 90 W (1/8 HP), 150 W (1/5 HP) Frame Size: □80 mm (□3.15 in.), □90 mm (□3.54 in.)

1 W, 3 W (1/750 HP, 1/250 HP) 6W (1/125 HP) 15 W (1/50 HP)

■ Specifications – Continuous Rating Model

Output Power

25 W (1/30 HP)

Round Shaft Type

W

HP

4IK40A-BW2U

40

1/19

40 W (1/19 HP) 90 W (1/8 HP)

Frequency

Current

VAC Single-Phase 110 Single-Phase 115

Hz

A 0.68 0.66 0.30 0.31 0.33 0.32 0.98 0.97 0.44 0.51 0.47 0.52 0.94 0.93

mN·m

oz-in

90

36

1/20

Single-Phase 220

40

1/19

Single-Phase 230

60

1/12

Single-Phase 110 Single-Phase 115

4IK40A-DW3E

4IK60A-BW2U 60 W (1/12 HP)

Voltage

55

1/14

Single-Phase 220

60

1/12

Single-Phase 230

60

1/12

Single-Phase 110 Single-Phase 115

4IK60A-DW3E

5IK60A-BW2U

Single-Phase 220 200 W (1/4 HP)

5IK60A-DW3E

60

1/12 Single-Phase 230 Three-Phase 200

2-Pole 40-150 W (1/19-1/5 HP)

5IK60A-TW2

60

1/12

5IK90A-BW2U

90

1/8

Three-Phase 220 Three-Phase 230 Single-Phase 110 Single-Phase 115 Single-Phase 220

5IK90A-DW3E

90

1/8 Single-Phase 230 Three-Phase 200

5IK90A-TW2

90

1/8

5IK150A-BW2U

150

1/5

140

1/5

Single-Phase 220

150

1/5

Single-Phase 230

150

1/5

Three-Phase 220 Three-Phase 230 Single-Phase 110 Single-Phase 115

5IK150A-DW3E

5IK150A-TW2 5IK150A-TW2T

Three-Phase 200 Three-Phase 220 Three-Phase 230

60 50 60 50 60 60 50 60 50 60 60 50 60 50 60 50 60 60 60 60 50 60 50 60 50 60 60 60 60 50 60 50 60 50 60 60 60

Starting Torque

Rated Torque

Rated Speed

Capacitor

r/min

μF

mN·m

oz-in

12.7

135

19.1

2900

7.5

90

12.7

145 120 160 135

20 17.0 22 19.1

2400 2900 2400 2900

1.8

160

22

190

26

3000

10

160

22

210 180 230 190

29 25 32 26

2500 3000 2500 3000

2.5

140

19.8

185

26

3200

14

0.46

120

17.0

0.45

140

19.8

0.47 0.40 0.42 0.44 1.61 1.57 0.70 0.84 0.69 0.84 0.63 0.55 0.57 0.59 2.12 2.09 0.98 1.07 1.04 1.13 1.11 0.93 0.97 1.01

270 230 230 230

38 32 32 32

220 185 220 185 220 185 185 185

31 26 31 26 31 26 26 26

2650 3200 2650 3200 2650 3200 3200 3200

240

34

280

39

3200

46 39 46 39 48 40 40 40

2650 3200 2650 3200 2600 3100 3200 3200

240

34

500 400 400 400

71 56 56 56

330 280 330 280 340 285 285 285

380

53

460

65

3200

510 420 560 460 550 460 460 460

72 59 79 65 78 65 65 65

2650 3200 2650 3200 2650 3100 3150 3200

380

53

680 570 570 570

96 80 80 80

3.0

−

25

6.0

−

30

8.0

−

● The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. ➜ Page G-11 ● Details of safety standards ➜ Page G-2 ● Details of RoHS Directive ➜ Page G-38 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting.

A-72

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-72

Standard AC Motors

■ Product Line ● Motor Output Power 40 W (1/19 HP)

■ Dimensions

The following items are included in each product. Motor, Capacitor✽, Capacitor Cap✽, Operating Manual ✽ Only for single-phase motors

Reversible Motors

150 W (1/5 HP)

Induction Motors

90 W (1/8 HP)

Model 4IK40A-BW2U 4IK40A-DW3E 4IK60A-BW2U 4IK60A-DW3E 5IK60A-BW2U 5IK60A-DW3E 5IK60A-TW2 5IK90A-BW2U 5IK90A-DW3E 5IK90A-TW2 5IK150A-BW2U 5IK150A-DW3E 5IK150A-TW2 5IK150A-TW2T

Introduction

60 W (1/12 HP)

Voltage Single-Phase 110/115 VAC Single-Phase 220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC Single-Phase 110/115 VAC Single-Phase 220/230 VAC Three-Phase 200/220/230 VAC Three-Phase 200/220/230 VAC

Electromagnetic Brake Motors

Unit = mm (in.)

● 40 W (1/19 HP) 4IK40A-BW2U, 4IK40A-DW3E Mass: 1.5 kg (3.3 lb.)

V Series

16.5 (0.65)

9

□80 (□3.15)

0

ϕ73−0.030

2)

± 0.0

4±0.5

(3.70

Protective Earth Terminal M4

Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

21.5 (0.85)

5 (0.20) max.

4×ϕ5.5 (ϕ0.217) Thru

Protective Earth Terminal M4

22.5˚

Detail Drawing of Protective Earth Terminal

● 60 W (1/12 HP) 4IK60A-BW2U, 4IK60A-DW3E Mass: 1.8 kg (4.0 lb.)

16.5 (0.65)

2)

)

± 0.0

□80 (□3.15)

.5 94±0

21.5 (0.85) Protective Earth Terminal M4 Detail Drawing of Protective Earth Terminal

Brake Pack

22.5˚

Linear Heads

5 (0.20) max.

4×ϕ5.5 (ϕ0.217) Thru Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

(3.70

Protective Earth Terminal M4

(

□82 (□3.23)

(ϕ0.3937−00.0006)

Right-Angle Gearheads

25 (0.98)

0

ϕ10−0.015

Torque Motors

7 (0.28)

32 (1.26) 2 (0.08)

0 ϕ73−0.030 0 ϕ2.8740−0.0012

100 (3.94)

9 (0.35)

A513

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

ϕ79 (ϕ3.11)

25 (0.98)

0

ϕ8−0.015 0 (ϕ0.3150−0.0006 )

Clutch & Brake Motors

7 (0.28)

32 (1.26) 2 (0.08)

0 (ϕ2.8740−0.0012 )

85 (3.35)

7 (0.28)

A450

Accessories Installation

Product Line A-73 / Dimensions A-73 / Connection Diagrams A-76

A-73

A453

105 (4.13)

37 (1.46) 0

2)

±0.0

)

104±

□90 (□3.54)

9 (0.35)

0.5

(4.09

Protective Earth Terminal M4

(

1 W, 3 W (1/750 HP, 1/250 HP)

30 (1.18)

16.5 (0.65)

ϕ10−0.015 0 (ϕ0.3937−0.0006 )

2 (0.08)

0 ϕ83−0.035 0 ϕ3.2677−0.0014

7.5 (0.30)

ϕ89 (ϕ3.50)

Standard AC Motors

5IK60A-BW2U, 5IK60A-DW3E, 5IK60A-TW2 Mass: 2.5 kg (5.5 lb.)

6W (1/125 HP)

21.5 (0.85)

5 (0.20) max. 4×ϕ6.5 (ϕ0.256) Thru Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

Protective Earth Terminal M4

22.5˚

● 90 W (1/8 HP)

( 4×ϕ6.5 (ϕ0.256) Thru )

0.02

90 W (1/8 HP)

16.5 (0.65)

.09±

.5 (4

±0 104

□90 (□3.54)

30 (1.18)

0 ϕ3.2677−0.0014

0

37 (1.46)

0

2 (0.08)

□90 (□3.54)

60 W (1/12 HP)

7.5 (0.30)

11 (0.43)

40 W (1/19 HP)

120 (4.72)

)

A456

0 ϕ83−0.035

25 W (1/30 HP)

5IK90A-BW2U, 5IK90A-DW3E, 5IK90A-TW2 Mass: 2.7 kg (5.9 lb.)

ϕ12−0.018 (ϕ0.4724−0.0007)

15 W (1/50 HP)

Detail Drawing of Protective Earth Terminal

Protective Earth Terminal M4 5 (0.20) max.

21.5 (0.85)

200 W (1/4 HP)

Protective Earth Terminal M4

2-Pole 40-150 W (1/19-1/5 HP)

Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

22.5˚

Detail Drawing of Protective Earth Terminal

● 150 W (1/5 HP) 5IK150A-BW2U, 5IK150A-DW3E, 5IK150A-TW2 Mass: 3.2 kg (7.0 lb.)

37 (1.46)

30 (1.18)

4×ϕ6.5 (ϕ0.256) Thru

10

(4.09

Protective Earth Terminal M4 5 (0.20) max.

Motor Leads 300 mm (12 in.) Length UL Style 3271, AWG20

A-74

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

2)

± 0.0

4±0.5

16.5 (0.65)

2 (0.08)

□90 (□3.54)

□90 (□3.54)

7.5 (0.30)

11 (0.43)

135 (5.31)

0 ϕ12−0.018 0 ϕ83−0.035

(ϕ0.4724−00.0007) (ϕ3.2677−00.0014)

A459

21.5 (0.85) Protective Earth Terminal M4

22.5˚

Detail Drawing of Protective Earth Terminal

Features A-20 / System Configuration A-23 / Specifications A-72

Standard AC Motors

5IK150A-TW2T Mass: 3.3 kg (7.3 lb.)

) (

□90 (□3.54)

□90 (□3.54)

133 (5.24)

0

11 (0.43)

0 ϕ3.2677−0.0014

Reversible Motors

2 (0.08) 37 (1.46)

135 (5.31)

.5

±0 104 ± 0.02) 9 0 . 4 (

Induction Motors

30 (1.18)

7.5 (0.30)

62 (2.44)

0 ϕ83−0.035

6 (0.24)

43 (1.69) 25 (0.98)

75 (2.95)

0

28 (1.10) max.

Introduction

ϕ12−0.018 (ϕ0.4724−0.0007)

A334

4×ϕ6.5 (ϕ0.256) Thru

Electromagnetic Brake Motors

● Use cable with a diameter of ϕ6 ∼ ϕ12 mm (ϕ0.24 ∼ ϕ0.47 in.). ● Details of terminal box ➜ Page A-314

● Capacitor (Included with single-phase motors)

7 (0.28) 10 (0.39)

6 (0.24)

B+15 (0.59)

B

B+10 (0.39)

B 4.5 (0.18) 10 (0.39)

ϕ4.3 20 (ϕ0.169) ( 0.79)

6 (0.24)

R (R 10 0.3 9)

4 (0.16)

C

4 (0.16)

C

AMP#187

◇ Capacitor Dimensions Model

A

B

C

Mass g (oz.)

Dimension No.

Capacitor Cap

CH75CFAUL2 CH18BFAUL CH100CFAUL2 CH25BFAUL CH140CFAUL2 CH30BFAUL CH250CFAUL2 CH60BFAUL CH300CFAUL2 CH80BFAUL

48 (1.89) 38 (1.50) 58 (2.28) 48 (1.89) 58 (2.28) 58 (2.28) 58 (2.28) 58 (2.28) 58 (2.28) 58 (2.28)

21 (0.83) 21 (0.83) 21 (0.83) 21 (0.83) 22 (0.87) 21 (0.83) 35 (1.38) 29 (1.14) 35 (1.38) 35 (1.38)

31 (1.22) 31 (1.22) 31 (1.22) 31 (1.22) 35 (1.38) 31 (1.22) 50 (1.97) 41 (1.61) 50 (1.97) 50 (1.97)

41 (1.45) 37 (1.31) 49 (1.73) 42 (1.48) 61 (2.2) 50 (1.77) 140 (4.9) 92 (3.2) 140 (4.9) 136 (4.6)

① ① ① ① ① ① ② ② ② ②

Included

Torque Motors Right-Angle Gearheads Linear Heads

4IK40A-BW2U 4IK40A-DW3E 4IK60A-BW2U 4IK60A-DW3E 5IK60A-BW2U 5IK60A-DW3E 5IK90A-BW2U 5IK90A-DW3E 5IK150A-BW2U 5IK150A-DW3E

Unit = mm (in.)

Capacitor Model

Synchronous Low-Speed Watertight, Motors Synchronous Dust-Resistant Motors Motors

AMP#187

A

Clutch & Brake Motors

ϕ4.3 20 (ϕ0.169) (0.79)

Dimension No. ②

V Series

Dimension No. ①

A

Brake Pack Accessories Installation

Product Line A-73 / Dimensions A-73 / Connection Diagrams A-76

A-75

Standard AC Motors

■ Connection Diagrams ● The direction of motor rotation is as viewed from the shaft end of the motor. CW represents the clockwise direction, while CCW represents the counterclockwise direction. Three-Phase 200/220/230 VAC

1 W, 3 W (1/750 HP, 1/250 HP)

Single-Phase 110/115 VAC Single-Phase 220/230 VAC

6W (1/125 HP)

CW

Clockwise

Lead Wire Type

Terminal Box Type

5IK60A-TW2 5IK90A-TW2 5IK150A-TW2

5IK150A-TW2T

Clockwise

Clockwise

CW

CW White Red Blue

L

L1(R) Motor

15 W (1/50 HP)

Gray Black

N

PE

L2(S) L3(T)

Red White

Motor

Black

PE

L1(R) L2(S) L3(T)

U V W

Motor

PE Capacitor

25 W (1/30 HP)

CCW

Counterclockwise

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

White

40 W (1/19 HP)

L N

Red Blue

Motor

Gray Black

Counterclockwise To change the rotation direction, change any two connections between L1(R), L2(S) and L3(T).

PE

Capacitor 60 W (1/12 HP)

PE: Protective Earth Note: ● Change the direction of single-phase motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, motor may ignore reversing command or change its direction of rotation after some delay.

90 W (1/8 HP)

● How to connect a capacitor ➜ Page A-313

200 W (1/4 HP) 2-Pole 40-150 W (1/19-1/5 HP)

A-76

ORIENTAL MOTOR GENERAL CATALOG 2009/2010

Features A-20 / System Configuration A-23 / Specifications A-72