Installation Instruction IMPORTANT WARNING MOUNTING HOOK
Installation Instruction UHB Series High Bay
IMPORTANT READ CAREFULLY BEFORE INSTALLING THE FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. THOROUGHLY INSPECT THE FIXTURE FOR ANY FREIGHT DAMAGE; FREIGHT DAMAGE SHOULD BE REPORTED TO THE DELIVERY CARRIER. This luminaire must be installed in accordance with the NEC (National Electrical Code) or your local electrical code. If you are not familiar with these codes and requirements, consult a qualified electrician. This luminaire is suitable for dry and damp location. Maximum ambient operating temperature: 50°C. MIN 90°Csupply conductors. User should prepare necessary accessories and spare parts (not provided).
WARNING DANGER--RISK OF ELECTRIC SHOCK. Make sure power supply is OFF before installing or maintaining fixture. No user serviceable parts inside. Check to make sure that all input power connections have been properly made and the fixture is grounded to avoid potential electrical shock. DO NOT lift luminaire by the power leads or cord. Never perform maintenance or cleaning while fixture is energized. Disconnect power and allow fixture to cool before maintaining.
MOUNTING For each mounting application below, when mounting to surface ensure that the mounting surface and customer supplied hardware is capable of supporting the weight of the luminaire. The fixture can be hook mount (through factory-installed “O” ring), pendant mount (through customer supplied pendant stem) or surface mount (through factory-installed junction box).
HOOK MOUNT________________________________________________________________________ 1. 2. 3. 4.
Thread “O” ring into fixture and fasten it with provided screw, shown in Figure 1. Hang fixture onto hook, shown in Figure 2. Make sure all the screws are tightly fastened in case of any injuries. Install provided safety cable. Refer to safety cable installation instruction for complete instructions.
1
2
Installation Instruction UHB Series High Bay
REFLECTOR INSTALLATION_________________________________________________________ NOTE: Aluminum Reflector is sold separately as an accessory; please refer to installation sheet for complete installing instructions. 1. Loosen the (4) screws, shown in Figure 10, at least 0.1 inch from the heatsink. NOTE: The view in Figure 10 is of the underside of the luminaire. 2. Bring trim into housing and line up the (4) screws from Step 1, with the keyhole slots on the reflector. See Figure 11. 10
11
3. Rotate trim, turn clockwise and tighten the (4) screws from Step 1. See Figure 11.
SAFETY CABLE INSTALLATION______________________________________________________ NOTE: Safety cable is sold separately as an accessory; please refer to installation sheet in safety cable packaging for complete installing instructions. 12 1. Attach one end of the safety cable through the fin of the heatsink. See Figure 12. 2. Attach other end of the safety cable to mounting surfaces using customer supplied hardware.
Installation Instruction UHB Series High Bay
ELECTRICAL CONNECTION 1. Wire input end of the LED driver to supply wires using wire nut (not provided) according to wiring section. 2. Connect the BLACK/BROWN lead to LINE (+) supply lead. 3. Connect the WHITE/BLUE lead to NEUTRAL/COMMON (-) supply lead. 4. Connect the GREEN lead to GROUND supply lead. 5. If any, connect PURPLE/BLUE to 0-10V SIGNAL supply lead and GREY/WHITE to 010V NEUTRAL/REFERENCE supply lead.
IMPORTANT READ CAREFULLY BEFORE INSTALLING THE FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. THOROUGHLY INSPECT THE FIXTURE FOR ANY FREIGHT DAMAGE; FREIGHT DAMAGE SHOULD BE REPORTED TO THE DELIVERY CARRIER. This luminaire must be installed in accordance with the NEC (National Electrical Code) or your local electrical code. If you are not familiar with these codes and requirements, consult a qualified electrician. This luminaire is suitable for dry and damp location. Maximum ambient operating temperature: 50°C. MIN 90°Csupply conductors. User should prepare necessary accessories and spare parts (not provided).
WARNING DANGER--RISK OF ELECTRIC SHOCK. Make sure power supply is OFF before installing or maintaining fixture. No user serviceable parts inside. Check to make sure that all input power connections have been properly made and the fixture is grounded to avoid potential electrical shock. DO NOT lift luminaire by the power leads or cord. Never perform maintenance or cleaning while fixture is energized. Disconnect power and allow fixture to cool before maintaining.
MOUNTING For each mounting application below, when mounting to surface ensure that the mounting surface and customer supplied hardware is capable of supporting the weight of the luminaire. The fixture can be hook mount (through factory-installed “O” ring), pendant mount (through customer supplied pendant stem) or surface mount (through factory-installed junction box).
HOOK MOUNT________________________________________________________________________ 1. 2. 3. 4.
Thread “O” ring into fixture and fasten it with provided screw, shown in Figure 1. Hang fixture onto hook, shown in Figure 2. Make sure all the screws are tightly fastened in case of any injuries. Install provided safety cable. Refer to safety cable installation instruction for complete instructions.
1
2
Installation Instruction UHB Series High Bay
REFLECTOR INSTALLATION_________________________________________________________ NOTE: Aluminum Reflector is sold separately as an accessory; please refer to installation sheet for complete installing instructions. 1. Loosen the (4) screws, shown in Figure 10, at least 0.1 inch from the heatsink. NOTE: The view in Figure 10 is of the underside of the luminaire. 2. Bring trim into housing and line up the (4) screws from Step 1, with the keyhole slots on the reflector. See Figure 11. 10
11
3. Rotate trim, turn clockwise and tighten the (4) screws from Step 1. See Figure 11.
SAFETY CABLE INSTALLATION______________________________________________________ NOTE: Safety cable is sold separately as an accessory; please refer to installation sheet in safety cable packaging for complete installing instructions. 12 1. Attach one end of the safety cable through the fin of the heatsink. See Figure 12. 2. Attach other end of the safety cable to mounting surfaces using customer supplied hardware.
Installation Instruction UHB Series High Bay
ELECTRICAL CONNECTION 1. Wire input end of the LED driver to supply wires using wire nut (not provided) according to wiring section. 2. Connect the BLACK/BROWN lead to LINE (+) supply lead. 3. Connect the WHITE/BLUE lead to NEUTRAL/COMMON (-) supply lead. 4. Connect the GREEN lead to GROUND supply lead. 5. If any, connect PURPLE/BLUE to 0-10V SIGNAL supply lead and GREY/WHITE to 010V NEUTRAL/REFERENCE supply lead.
