Installation - Security Door Controls
801 Avenida Acaso, Camarillo, Ca. 93041 • (805) 494-0622 • Fax: (805) 494-8861 www.sdcsecurity.com • E-mail: [email protected]
INSTALLATION INSTRUCTIONS 160, 260 SERIES GATELOCK
4.25" standard
Four electric models are available: the GL 260A is the fail-secure (PUL) model, operating on 24 VDC; GL 263A has a built-in key switch control, GL 160A is fail-safe (PL) and has a built-in key switch control.
Plan View
2" post standard
GateLok
An adjustable automatic relock switch keeps the bolt retracted until the gate is in a closed position. A 10 Amp rated bolt position switch (BPS-GL, optional) prevents operation of the gate until the bolt is fully retracted. A gate position switch (DPS-GL, optional) is available to monitor whether a gate is opened or closed.
Locking tongue
5" Left Hand shown
Right Hand opposite
DUAL VOLTAGE SOLENOID WIRING
Specifications Dimensions: Width 5", Height 6-1/8”, Depth 2" 12VDC CONFIGURATION Material: 0.120" steel .6 AMP Finish: Cadmium plated Solenoid: Continuous duty Dual Voltage (Fail Safe): Single Voltage (Fail Secure): 7.2 Watts – 12VDC @ .6 Amp 24VDC @ .500 Amp standard 7.2 Watts – 24VDC @ .3 Amp (12 VDC, 24 VDC available) Bolt: 5/8” dia., 5/8” throw
P:\INSTALLATION INST\ELECTRIC BOLT LOCKS\INST-Gate Lock SERIES\INST-GL Series
3" post standard
REV G
07-13
RED BLK
RED (+)
BLU WHT
WHT (-)
Page 1
24VDC CONFIGURATION .3 AMP
RED BLK
RED (+)
BLU WHT
WHT (-)
Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email [email protected]
CAUTION: DO NOT PLACE LOCKING TONGUE IN LOCK UNTIL WIRING IS COMPLETE For 160A & 260A (less key switch): 1. Remove cover and using the lock housing as a template, locate and mark mounting bolt holes on the gate post. Drill through post for 2-3/8” hex head bolts supplied. See illustration 1. 2. Determine hand of gate and install Auto Relock switch and the spring loaded centering assembly in their proper locations. See illustration 2. 3. If the wiring will come through the post, mark and drill post at lower housing hole for wiring assembly. Pull wires in through the back of housing through lower hole. Be sure to shim between the mounting brackets as required if the gate post is less than 3". 4. Wire the assembly per illustration 2 and illustration 3. Test for proper operation. 5. Insert gate lock tongue into slot and line up tongue level on gate. Mark gate for tongue mounting bolts. 6. Remove locking tongue. Drill gate and mount tongue using 4-3/8” carriage head bolts provided. See illustration 4. 7. Install housing cover with machine screws provided.
Power _ +
Centering Assembly
ORG
R
ORG
W
A R S
Illustration 1
Auto Relock switch
Illustration 2
Wiring for 200 Series Locks 24VDC
-
+
Momentary normally open key or push switch for access control
OR OR Relock switch Lock
R W
Solenoid 24VDC
Illustration 3
Illustration 4
NOTE: Sliding Gate left hand and swinging gate right hand shown in illustrations 2 & 3. Exchange positions of centering assembly and automatic relock switch for opposite handing. P:\INSTALLATION INST\ELECTRIC BOLT LOCKS\INST-Gate Lock SERIES\INST-GL Series
REV G
07-13
Page 2
For 163A & 263A (with key switch): Follow installation steps 1 – 3 on page 2. 4. Wire the assembly per illustrations 5, 6, 7 & 8. a) Cylinder must be 1-1/8” mortise type with standard tailpiece. See illustrations 5 & 6. b) With key removed, remove and invert tailpiece. See illustration 6. c) Key removable in “ON” or “OFF” position as determined by wiring selection. See illustration 7. 24 VDC
Follow installation steps 5 – 7 on page 2.
Cylinder Lock Nut
Tailpiece must depress button at all times with key removed.
Optional Rubber Spacer
Key switch 10 Amp – 30V
Install stop screws N.C.
Auto Relock switch 10 Amp – 30V R
Illustration 5
Solenoid
N.O.
1-1/2”
W
Illustration 6
NC
YEL
W COM
Key Switch Assembly (Rotated 90 as shown in View A-A)
ORG
Illustration 7 Optional bolt position switch (BPS-GL) rated 10 Amp 30V
DIRECTION OF KEY TURN
Bolt Position Switch (optional) Auto Relock Switch
A
Illustration 8
A
Optional Rubber Spacer
VIEW A-A
DIRECTION OF KEY TURN If Key Cylinder is ever removed, tailpiece must contact retraction arm as shown in View A-A. P:\INSTALLATION INST\ELECTRIC BOLT LOCKS\INST-Gate Lock SERIES\INST-GL Series
REV G
07-13
Page 3
INSTALLATION INSTRUCTIONS 160, 260 SERIES GATELOCK
4.25" standard
Four electric models are available: the GL 260A is the fail-secure (PUL) model, operating on 24 VDC; GL 263A has a built-in key switch control, GL 160A is fail-safe (PL) and has a built-in key switch control.
Plan View
2" post standard
GateLok
An adjustable automatic relock switch keeps the bolt retracted until the gate is in a closed position. A 10 Amp rated bolt position switch (BPS-GL, optional) prevents operation of the gate until the bolt is fully retracted. A gate position switch (DPS-GL, optional) is available to monitor whether a gate is opened or closed.
Locking tongue
5" Left Hand shown
Right Hand opposite
DUAL VOLTAGE SOLENOID WIRING
Specifications Dimensions: Width 5", Height 6-1/8”, Depth 2" 12VDC CONFIGURATION Material: 0.120" steel .6 AMP Finish: Cadmium plated Solenoid: Continuous duty Dual Voltage (Fail Safe): Single Voltage (Fail Secure): 7.2 Watts – 12VDC @ .6 Amp 24VDC @ .500 Amp standard 7.2 Watts – 24VDC @ .3 Amp (12 VDC, 24 VDC available) Bolt: 5/8” dia., 5/8” throw
P:\INSTALLATION INST\ELECTRIC BOLT LOCKS\INST-Gate Lock SERIES\INST-GL Series
3" post standard
REV G
07-13
RED BLK
RED (+)
BLU WHT
WHT (-)
Page 1
24VDC CONFIGURATION .3 AMP
RED BLK
RED (+)
BLU WHT
WHT (-)
Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email [email protected]
CAUTION: DO NOT PLACE LOCKING TONGUE IN LOCK UNTIL WIRING IS COMPLETE For 160A & 260A (less key switch): 1. Remove cover and using the lock housing as a template, locate and mark mounting bolt holes on the gate post. Drill through post for 2-3/8” hex head bolts supplied. See illustration 1. 2. Determine hand of gate and install Auto Relock switch and the spring loaded centering assembly in their proper locations. See illustration 2. 3. If the wiring will come through the post, mark and drill post at lower housing hole for wiring assembly. Pull wires in through the back of housing through lower hole. Be sure to shim between the mounting brackets as required if the gate post is less than 3". 4. Wire the assembly per illustration 2 and illustration 3. Test for proper operation. 5. Insert gate lock tongue into slot and line up tongue level on gate. Mark gate for tongue mounting bolts. 6. Remove locking tongue. Drill gate and mount tongue using 4-3/8” carriage head bolts provided. See illustration 4. 7. Install housing cover with machine screws provided.
Power _ +
Centering Assembly
ORG
R
ORG
W
A R S
Illustration 1
Auto Relock switch
Illustration 2
Wiring for 200 Series Locks 24VDC
-
+
Momentary normally open key or push switch for access control
OR OR Relock switch Lock
R W
Solenoid 24VDC
Illustration 3
Illustration 4
NOTE: Sliding Gate left hand and swinging gate right hand shown in illustrations 2 & 3. Exchange positions of centering assembly and automatic relock switch for opposite handing. P:\INSTALLATION INST\ELECTRIC BOLT LOCKS\INST-Gate Lock SERIES\INST-GL Series
REV G
07-13
Page 2
For 163A & 263A (with key switch): Follow installation steps 1 – 3 on page 2. 4. Wire the assembly per illustrations 5, 6, 7 & 8. a) Cylinder must be 1-1/8” mortise type with standard tailpiece. See illustrations 5 & 6. b) With key removed, remove and invert tailpiece. See illustration 6. c) Key removable in “ON” or “OFF” position as determined by wiring selection. See illustration 7. 24 VDC
Follow installation steps 5 – 7 on page 2.
Cylinder Lock Nut
Tailpiece must depress button at all times with key removed.
Optional Rubber Spacer
Key switch 10 Amp – 30V
Install stop screws N.C.
Auto Relock switch 10 Amp – 30V R
Illustration 5
Solenoid
N.O.
1-1/2”
W
Illustration 6
NC
YEL
W COM
Key Switch Assembly (Rotated 90 as shown in View A-A)
ORG
Illustration 7 Optional bolt position switch (BPS-GL) rated 10 Amp 30V
DIRECTION OF KEY TURN
Bolt Position Switch (optional) Auto Relock Switch
A
Illustration 8
A
Optional Rubber Spacer
VIEW A-A
DIRECTION OF KEY TURN If Key Cylinder is ever removed, tailpiece must contact retraction arm as shown in View A-A. P:\INSTALLATION INST\ELECTRIC BOLT LOCKS\INST-Gate Lock SERIES\INST-GL Series
REV G
07-13
Page 3
