iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement Replace the FaceTime camera and sensor assembly flex cable in an iPhone 6s Plus.
Written By: Evan Noronha INTRODUCTION Follow the steps in this guide to replace the FaceTime camera and sensor assembly flex cable in an iPhone 6s Plus.
TOOLS: Suction Handle (1) Spudger (1) P2 Pentalobe Screwdriver iPhone (1) Phillips #00 Screwdriver (1) Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 1 — Pentalobe Screws
Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
Power off your iPhone before beginning disassembly.
Remove the two 3.4 mm Pentalobe screws on either side of the Lightning port.
Step 2 — Opening Procedure
Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It's possible to complete the repair without replacing the adhesive, and you probably won't notice any difference in functionality.
© iFixit — CC BY-NC-SA
www.iFixit.com
Apply a suction cup to the lower left corner of the display assembly. Page 2 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 3
Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Pulling too hard may damage the display assembly. Apply just enough pressure to create a small gap between the display assembly and the rear case.
Step 4
The safest place to pry from is the notch in the front panel above the headphone jack.
While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 5
Twist the spudger to widen the gap between the front panel and the rear case.
Step 6
While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 7
Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case.
Step 8
Insert the flat tip of the spudger under the right edge of the display.
Slide the spudger up the right side.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 9
Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone.
Do not remove the display completely, or you will damage the data cables connecting the display near the top edge of the iPhone.
Step 10
Pull up on the small nub on the suction cup to remove it from the display.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 11
Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.
Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily.
Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
In a pinch, you can use an unopened canned beverage to support the display.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 12 — Battery Connector
Remove the following Phillips screws securing the battery connector bracket to the logic board:
One 2.9 mm screw
One 2.3 mm screw
Step 13
Remove the battery connector bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 14
Use the pointed tip of the spudger to disconnect the battery connector from the logic board.
Step 15
Bend the connector back to ensure it doesn't make contact and power the iPhone on while you're working on it.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 16 — Display Assembly
Remove the following Phillips screws:
Three 1.3 mm screws
One 1.6 mm screw
One 3.0 mm screw
During reassembly, it's critical to place this 3.0 mm screw in the top-right corner of the bracket. Placing it anywhere else may damage the logic board.
Step 17
Remove the display cable bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 10 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 18
Be careful to only pry up on the connector itself and not the socket on the logic board.
Use a plastic opening tool to disconnect the front-facing camera and sensor cable connector.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 11 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 19
Use a plastic opening tool to disconnect the digitizer cable by prying it straight up from its socket on the logic board.
When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 12 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 20
Use a plastic opening tool to disconnect the display data cable by prying it straight up from its socket on the logic board.
Step 21
Remove the display assembly.
During reassembly, if you are applying a new set of adhesive strips around the display, first clean and remove the old adhesive and then carefully press the new adhesive strips into place. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 13 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 22 — Earpiece Speaker
Remove the following three Phillips screws:
Two 2.7 mm screws
One 1.4 mm screw
Step 23
Remove the earpiece speaker bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 14 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 24
Use the flat end of a spudger to lift the FaceTime camera out of its housing.
Step 25
Pull the FaceTime camera back and remove the earpiece speaker.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 15 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 26 — FaceTime Camera and Sensor Assembly
Use the pointed tip of a spudger to lift the ambient light sensor from its housing in the front panel.
Step 27
Insert the pointed tip of a spudger between the microphone flex cable and the front panel to break the adhesive holding it in place.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 16 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 28
Use the flat tip of a spudger to lift up the microphone and earpiece gasket.
Step 29
Remove the FaceTime camera and sensor assembly.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-04-22 05:54:28 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 17 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement Replace the FaceTime camera and sensor assembly flex cable in an iPhone 6s Plus.
Written By: Evan Noronha INTRODUCTION Follow the steps in this guide to replace the FaceTime camera and sensor assembly flex cable in an iPhone 6s Plus.
TOOLS: Suction Handle (1) Spudger (1) P2 Pentalobe Screwdriver iPhone (1) Phillips #00 Screwdriver (1) Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 1 — Pentalobe Screws
Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
Power off your iPhone before beginning disassembly.
Remove the two 3.4 mm Pentalobe screws on either side of the Lightning port.
Step 2 — Opening Procedure
Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It's possible to complete the repair without replacing the adhesive, and you probably won't notice any difference in functionality.
© iFixit — CC BY-NC-SA
www.iFixit.com
Apply a suction cup to the lower left corner of the display assembly. Page 2 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 3
Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Pulling too hard may damage the display assembly. Apply just enough pressure to create a small gap between the display assembly and the rear case.
Step 4
The safest place to pry from is the notch in the front panel above the headphone jack.
While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 5
Twist the spudger to widen the gap between the front panel and the rear case.
Step 6
While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 7
Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case.
Step 8
Insert the flat tip of the spudger under the right edge of the display.
Slide the spudger up the right side.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 9
Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone.
Do not remove the display completely, or you will damage the data cables connecting the display near the top edge of the iPhone.
Step 10
Pull up on the small nub on the suction cup to remove it from the display.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 11
Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.
Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily.
Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
In a pinch, you can use an unopened canned beverage to support the display.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 12 — Battery Connector
Remove the following Phillips screws securing the battery connector bracket to the logic board:
One 2.9 mm screw
One 2.3 mm screw
Step 13
Remove the battery connector bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 14
Use the pointed tip of the spudger to disconnect the battery connector from the logic board.
Step 15
Bend the connector back to ensure it doesn't make contact and power the iPhone on while you're working on it.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 16 — Display Assembly
Remove the following Phillips screws:
Three 1.3 mm screws
One 1.6 mm screw
One 3.0 mm screw
During reassembly, it's critical to place this 3.0 mm screw in the top-right corner of the bracket. Placing it anywhere else may damage the logic board.
Step 17
Remove the display cable bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 10 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 18
Be careful to only pry up on the connector itself and not the socket on the logic board.
Use a plastic opening tool to disconnect the front-facing camera and sensor cable connector.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 11 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 19
Use a plastic opening tool to disconnect the digitizer cable by prying it straight up from its socket on the logic board.
When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 12 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 20
Use a plastic opening tool to disconnect the display data cable by prying it straight up from its socket on the logic board.
Step 21
Remove the display assembly.
During reassembly, if you are applying a new set of adhesive strips around the display, first clean and remove the old adhesive and then carefully press the new adhesive strips into place. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 13 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 22 — Earpiece Speaker
Remove the following three Phillips screws:
Two 2.7 mm screws
One 1.4 mm screw
Step 23
Remove the earpiece speaker bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 14 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 24
Use the flat end of a spudger to lift the FaceTime camera out of its housing.
Step 25
Pull the FaceTime camera back and remove the earpiece speaker.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 15 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 26 — FaceTime Camera and Sensor Assembly
Use the pointed tip of a spudger to lift the ambient light sensor from its housing in the front panel.
Step 27
Insert the pointed tip of a spudger between the microphone flex cable and the front panel to break the adhesive holding it in place.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 16 of 17
iPhone 6s Plus FaceTime Camera and Sensor Assembly Replacement
Step 28
Use the flat tip of a spudger to lift up the microphone and earpiece gasket.
Step 29
Remove the FaceTime camera and sensor assembly.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-04-22 05:54:28 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 17 of 17
