Ledco 42 60 Parts
Ledco Digital 42 & 60 Series Laminator
Parts Views
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Ledco Digital 42 & 60 Series Laminator Left Side (with housing, cover, chains, etc) parts views D105 094.4LT Upper Left Digital Housing
D105 053.4 Upper Idler Brkt (2)
PRS054 Emergency Pushbutton actuator (4)
D60 080.4 Shoulder Bolt Stabilizer (2) D105 105.4T Fixed Hinge Block,Top (2) D105 097.4 Housing Cover Latch Brkt (4)
D105 095.4L Hsng Cover Left Door
PML002 ¼ Turn Latch Set (4) D105 106.4 Rotating Hinge Block (4) LC38 067.4 Bottom Heat Shoe Fastener (2)
D105 105.4B Fixed Hinge Block,Bottom (2)
D105 098.4 Housing Corner Brace (4)
D105 094.4 Lower Left Digital Housing
PRH168 5/8” Dia Hole Plug (8)
Ledco Digital 42 & 60 Laminator S-Wrap Idler Assembly parts views
D105 or D60 251.4 SWrap Idler Shaft (inside the idler tube, 1)
PRB086A Brng Idler(2)
D105 or D60 303.4 Thermal Idler Tube (1)
¼ 20 x ¾ Truss Head machine screw (2)
D105 250.4 S-Wrap Idler Brkt (2) D105 252.4 Mntg Bshg (2)
Part numbers for S-Wrap assemblies are 8342100 (42) & 8360100 (60) respectively
To install slitter option to a pre-existing D42 or D60
You will need a long necked phillips head screwdiver with interchangeable heads to accommodate a #2 square drive bit (included)
UNPLUG THE MACHINE FROM ITS POWER SOURCE!!!!
Follow these directions and if you have any questions call Tami Berry @ Graphic Laminating for assistance 800-345-5300 Using your phillips head screwdriver,open the left side housing door,locate and remove these two screws from the rear bottom,outside housing edge
Page 1
Ledco Digital 42 & 60 Series Laminator Safety Shield Assembly parts views LAB21 Safety Shield Warning Label (2)
D105 or D60 102.4 Safety Shield (1)
PRK177 Thumbscrew (2 or 3)
D105 099.4 Anti-curl Strip Mntg Bshng (5, 7)
D60 091.4R Pivoting Safety Shield Brkt, right (1)
D105 or D60 075.4 Lay Down Strip (1)
1/8 “ x 3/4 Spring Pin (2)
LAB100 “HOT” Label
Grease stain from Colleen’s hideous breakfast sandwich
D60 091.4L Pivoting Safety Shield Brkt, left (1)
Ledco Digital 42 & 60 Laminator Roll Feed Option Parts Views
LC38 096.4C Roll Feed Brkt Adptr Block (2)
LC38 096.4B Roll Feed Bracket (2)
8442200 for 42, 8460200 for 60 Supply Roll Assembly used in Roll Feed Option (1)
10-32 x 1 ½” Socket Head Screws (4) used to secure the brackets and adaptors to the feed tray as shown using a 5/32 Allen wrench
Assembly part #’s for the Roll Feed Option are 8342500 for D42 and 8360500 for D60
Ledco Digital 42 & 60 Series Laminator Right Side Door parts views
D105 095.4R Hsng Cover Door, right (1) PML 002 ¼ Turn Latch Set (4)
D105 097.4 Hsng Cover Latch Brkt (4)
LAB050A Domed Ledco Emblem (3)
PRH140 Cam Shaft Handle (2)
Miles of bundled wires that vaguely resemble spaghetti
EP25 004.4 Friction Washer, Teflon (4)
D105 105.4T Fixed Hinge Block, top (2)
LAB51 “Oh Shit, I’ve Torn My Arms Off” Warning Label (2)
D105 106.4 Rotating Hinge Block (4)
Not totally dissimilar to a bird’s nest
D105 131.4 Cam Shaft Handle Locator (2)
PML002 ¼ Turn Latch Set (4)
EP25 004.4 Friction Washer, Teflon (4) RRS352 Proximity Switch Magnet (3) D105 105.4B Fixed Hinge Block, bottom (2)
Ledco Digital 42 & 60 Series Laminator Left Side (without housing/cover or chains & sprockets) parts views PRS320 35B12 Idler Sprckt (4)
LC38 054.4 Top RR Idler Sprckt Brkt
D60 090.4L Left Side Panel
LC38 032.4 Top Left Outer RR Spacer (4) Not Shown LC38 031.4 Inner RR Spacer (4)
LC38 033.4 Bottom RR spacer (2)
PRS313 6X289 Lever Type Micro-switch
LC38 170.4 Safety Switch Brkt
PRM2000 LeesonBaldor Motor
PRS320 (idler Sprocket) is this also what you want? (cog)
LC38 055.4 Lower Chain Adj Block
Sholder bolt for idler sprocket is this what you need?
PRB064 Snap Bshg .875
Ledco Digital 42 & 60 Series Laminator Left Side (with housing, cover, chains, etc) parts views D105 094.4LT Upper Left Digital Housing
D105 053.4 Upper Idler Brkt (2)
PRS054 Emergency Pushbutton actuator (4)
D60 080.4 Shoulder Bolt Stabilizer (2) D105 105.4T Fixed Hinge Block,Top (2) D105 097.4 Housing Cover Latch Brkt (4)
D105 095.4L Hsng Cover Left Door
PML002 ¼ Turn Latch Set (4) D105 106.4 Rotating Hinge Block (4) LC38 067.4 Bottom Heat Shoe Fastener (2)
D105 105.4B Fixed Hinge Block,Bottom (2)
D105 098.4 Housing Corner Brace (4)
D105 094.4 Lower Left Digital Housing
PRH168 5/8” Dia Hole Plug (8)
Ledco Digital 42 & 60 Series Laminator Heat Shoe Assembly parts views PRC212S Sensor for Trakstat shown installed in heat shoe (1 per heat shoe assembly)
D105 or D60 060.4 Heat Shoe (2)
LC38 064.4 Heat Shoe Spacer (4 per asmbly) ¼ 20 x 1 1/2” Hex Bolts (4 per asmbly) LC38 065.4 Heat Shoe Bracket for D42,60 (2 per asmbly)
PRI 163 or 164 Heat Shrink Tubing (random lengths)
PRH171 (42”) PRH172 (60”) Cartridge Heater (1 per asmbly)
LC38 344.4 Teflon Tubing for Heat Sensor (1 per asmbly)
PRC212S Sensor for Trakstat (1 per asmbly)
Ledco Digital 42 & 60 Series Laminator Feed Tray Assembly parts views LC38 097.4R Feed Table Guide Right (1)
Protective film, remove and discard
D105 101.4 Feed Table Mntg Stub (4) D105 or D60 108.4 Feed Table (1)
PRS352 Proximity Switch Magnet (1)
LC38 097.7L Feed Table Guide Left (1)
Hole for Hand Grip (2) D60 only
D105 or D60 054.4 Feed Table Idler Tube (1)
D105 or D60 109.4 Feed Table Idler Shaft (2)
D105 or D60 111.4 Feed Table Support Bar (1)
PRK184 Plastic Thumbscrew (4) D105 104.4 Feed Table Guide Block (4)
PRB 086A Idler Bearing (2)
Ledco Digital 42 & 60 Series Laminator Control Panel (right side) parts views PRK 185 red pushbutton cap PRK 186 blue pushbutton cap (2 ea per machine) PRS054 Emergency Pushbutton Activator (4) LED Display for PRH130 Heat Control Kit (2)
PRM221A Speed Dial Knob (1) LAB98 Digital Control Panel Decal (1)
D105 102.4 for D42 or D60 102.4 for D60 Safety Shield (1)
LAB050A Domed Ledco Emblem (3)
D105 091.4R Pivoting Safety Shield Brkt, right (1)
D60 098.4R Feed Table Brkt,right (1)
PRH 140 Cam Shaft Handle (2)
PRS020 2 Position For/Rev Switch (1) PRS017 Red Heat Switch (2)
PRS017 Green Drive Switch (1)
PRS019 Blue Fan Switch (1)
PRS016 Red Momentary Switch (1)
Ledco Digital 42 & 60 Series Laminator Supply Roll Mandrel Assembly Parts Views (asmbly part #’s 8442200 & 8460200 respectively) D105 002.4A for D42, D60 002.4A Supply Roll Mandrel (extruded style)
D105 021.4 for D42, D60 021.4 Supply Roll Gripper Rod (3)
D105 011.4A for D42, D60 011.4A Supply Roll Shaft
D105 003.4 Hex Bushing (2) LC38 004.4 Supply Roll Pressure Plate (2)
H380 004.4 Leather Disc (2), replaces smaller PRW336 LC38 023.4 Supply Roll Hex Adaptor
D105 008.4 Supply Roll End Cap (2) PRS222 Supply Roll Tension Spring (2)
D105 001.4 Supply Roll Tensioning Knob (2)
¼-20 x ½” SH Set Screw to secure hex Bushings in mandrel extrusion (2)
1/8” x ½ “ Spring Pin (6)
¼ “ x 1” Spring Pin (6)
D105 022.4 Adj Hex Adaptor w/ 1/8” x ¾” Spring Pin
D105 004.4 Stop Collar - Core Chuck Style (common to all Industrial, Digital, and Econocraft series laminators, 4 per machine)
PRK184 Plastic Thumbscrew (1 per stop collar)
3/8” dia x 1” Delrin rod inserts (standard, 2 per collar)
Stop Collar shown here in suggested operational position
Parts Views
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Ledco Digital 42 & 60 Series Laminator Left Side (with housing, cover, chains, etc) parts views D105 094.4LT Upper Left Digital Housing
D105 053.4 Upper Idler Brkt (2)
PRS054 Emergency Pushbutton actuator (4)
D60 080.4 Shoulder Bolt Stabilizer (2) D105 105.4T Fixed Hinge Block,Top (2) D105 097.4 Housing Cover Latch Brkt (4)
D105 095.4L Hsng Cover Left Door
PML002 ¼ Turn Latch Set (4) D105 106.4 Rotating Hinge Block (4) LC38 067.4 Bottom Heat Shoe Fastener (2)
D105 105.4B Fixed Hinge Block,Bottom (2)
D105 098.4 Housing Corner Brace (4)
D105 094.4 Lower Left Digital Housing
PRH168 5/8” Dia Hole Plug (8)
Ledco Digital 42 & 60 Laminator S-Wrap Idler Assembly parts views
D105 or D60 251.4 SWrap Idler Shaft (inside the idler tube, 1)
PRB086A Brng Idler(2)
D105 or D60 303.4 Thermal Idler Tube (1)
¼ 20 x ¾ Truss Head machine screw (2)
D105 250.4 S-Wrap Idler Brkt (2) D105 252.4 Mntg Bshg (2)
Part numbers for S-Wrap assemblies are 8342100 (42) & 8360100 (60) respectively
To install slitter option to a pre-existing D42 or D60
You will need a long necked phillips head screwdiver with interchangeable heads to accommodate a #2 square drive bit (included)
UNPLUG THE MACHINE FROM ITS POWER SOURCE!!!!
Follow these directions and if you have any questions call Tami Berry @ Graphic Laminating for assistance 800-345-5300 Using your phillips head screwdriver,open the left side housing door,locate and remove these two screws from the rear bottom,outside housing edge
Page 1
Ledco Digital 42 & 60 Series Laminator Safety Shield Assembly parts views LAB21 Safety Shield Warning Label (2)
D105 or D60 102.4 Safety Shield (1)
PRK177 Thumbscrew (2 or 3)
D105 099.4 Anti-curl Strip Mntg Bshng (5, 7)
D60 091.4R Pivoting Safety Shield Brkt, right (1)
D105 or D60 075.4 Lay Down Strip (1)
1/8 “ x 3/4 Spring Pin (2)
LAB100 “HOT” Label
Grease stain from Colleen’s hideous breakfast sandwich
D60 091.4L Pivoting Safety Shield Brkt, left (1)
Ledco Digital 42 & 60 Laminator Roll Feed Option Parts Views
LC38 096.4C Roll Feed Brkt Adptr Block (2)
LC38 096.4B Roll Feed Bracket (2)
8442200 for 42, 8460200 for 60 Supply Roll Assembly used in Roll Feed Option (1)
10-32 x 1 ½” Socket Head Screws (4) used to secure the brackets and adaptors to the feed tray as shown using a 5/32 Allen wrench
Assembly part #’s for the Roll Feed Option are 8342500 for D42 and 8360500 for D60
Ledco Digital 42 & 60 Series Laminator Right Side Door parts views
D105 095.4R Hsng Cover Door, right (1) PML 002 ¼ Turn Latch Set (4)
D105 097.4 Hsng Cover Latch Brkt (4)
LAB050A Domed Ledco Emblem (3)
PRH140 Cam Shaft Handle (2)
Miles of bundled wires that vaguely resemble spaghetti
EP25 004.4 Friction Washer, Teflon (4)
D105 105.4T Fixed Hinge Block, top (2)
LAB51 “Oh Shit, I’ve Torn My Arms Off” Warning Label (2)
D105 106.4 Rotating Hinge Block (4)
Not totally dissimilar to a bird’s nest
D105 131.4 Cam Shaft Handle Locator (2)
PML002 ¼ Turn Latch Set (4)
EP25 004.4 Friction Washer, Teflon (4) RRS352 Proximity Switch Magnet (3) D105 105.4B Fixed Hinge Block, bottom (2)
Ledco Digital 42 & 60 Series Laminator Left Side (without housing/cover or chains & sprockets) parts views PRS320 35B12 Idler Sprckt (4)
LC38 054.4 Top RR Idler Sprckt Brkt
D60 090.4L Left Side Panel
LC38 032.4 Top Left Outer RR Spacer (4) Not Shown LC38 031.4 Inner RR Spacer (4)
LC38 033.4 Bottom RR spacer (2)
PRS313 6X289 Lever Type Micro-switch
LC38 170.4 Safety Switch Brkt
PRM2000 LeesonBaldor Motor
PRS320 (idler Sprocket) is this also what you want? (cog)
LC38 055.4 Lower Chain Adj Block
Sholder bolt for idler sprocket is this what you need?
PRB064 Snap Bshg .875
Ledco Digital 42 & 60 Series Laminator Left Side (with housing, cover, chains, etc) parts views D105 094.4LT Upper Left Digital Housing
D105 053.4 Upper Idler Brkt (2)
PRS054 Emergency Pushbutton actuator (4)
D60 080.4 Shoulder Bolt Stabilizer (2) D105 105.4T Fixed Hinge Block,Top (2) D105 097.4 Housing Cover Latch Brkt (4)
D105 095.4L Hsng Cover Left Door
PML002 ¼ Turn Latch Set (4) D105 106.4 Rotating Hinge Block (4) LC38 067.4 Bottom Heat Shoe Fastener (2)
D105 105.4B Fixed Hinge Block,Bottom (2)
D105 098.4 Housing Corner Brace (4)
D105 094.4 Lower Left Digital Housing
PRH168 5/8” Dia Hole Plug (8)
Ledco Digital 42 & 60 Series Laminator Heat Shoe Assembly parts views PRC212S Sensor for Trakstat shown installed in heat shoe (1 per heat shoe assembly)
D105 or D60 060.4 Heat Shoe (2)
LC38 064.4 Heat Shoe Spacer (4 per asmbly) ¼ 20 x 1 1/2” Hex Bolts (4 per asmbly) LC38 065.4 Heat Shoe Bracket for D42,60 (2 per asmbly)
PRI 163 or 164 Heat Shrink Tubing (random lengths)
PRH171 (42”) PRH172 (60”) Cartridge Heater (1 per asmbly)
LC38 344.4 Teflon Tubing for Heat Sensor (1 per asmbly)
PRC212S Sensor for Trakstat (1 per asmbly)
Ledco Digital 42 & 60 Series Laminator Feed Tray Assembly parts views LC38 097.4R Feed Table Guide Right (1)
Protective film, remove and discard
D105 101.4 Feed Table Mntg Stub (4) D105 or D60 108.4 Feed Table (1)
PRS352 Proximity Switch Magnet (1)
LC38 097.7L Feed Table Guide Left (1)
Hole for Hand Grip (2) D60 only
D105 or D60 054.4 Feed Table Idler Tube (1)
D105 or D60 109.4 Feed Table Idler Shaft (2)
D105 or D60 111.4 Feed Table Support Bar (1)
PRK184 Plastic Thumbscrew (4) D105 104.4 Feed Table Guide Block (4)
PRB 086A Idler Bearing (2)
Ledco Digital 42 & 60 Series Laminator Control Panel (right side) parts views PRK 185 red pushbutton cap PRK 186 blue pushbutton cap (2 ea per machine) PRS054 Emergency Pushbutton Activator (4) LED Display for PRH130 Heat Control Kit (2)
PRM221A Speed Dial Knob (1) LAB98 Digital Control Panel Decal (1)
D105 102.4 for D42 or D60 102.4 for D60 Safety Shield (1)
LAB050A Domed Ledco Emblem (3)
D105 091.4R Pivoting Safety Shield Brkt, right (1)
D60 098.4R Feed Table Brkt,right (1)
PRH 140 Cam Shaft Handle (2)
PRS020 2 Position For/Rev Switch (1) PRS017 Red Heat Switch (2)
PRS017 Green Drive Switch (1)
PRS019 Blue Fan Switch (1)
PRS016 Red Momentary Switch (1)
Ledco Digital 42 & 60 Series Laminator Supply Roll Mandrel Assembly Parts Views (asmbly part #’s 8442200 & 8460200 respectively) D105 002.4A for D42, D60 002.4A Supply Roll Mandrel (extruded style)
D105 021.4 for D42, D60 021.4 Supply Roll Gripper Rod (3)
D105 011.4A for D42, D60 011.4A Supply Roll Shaft
D105 003.4 Hex Bushing (2) LC38 004.4 Supply Roll Pressure Plate (2)
H380 004.4 Leather Disc (2), replaces smaller PRW336 LC38 023.4 Supply Roll Hex Adaptor
D105 008.4 Supply Roll End Cap (2) PRS222 Supply Roll Tension Spring (2)
D105 001.4 Supply Roll Tensioning Knob (2)
¼-20 x ½” SH Set Screw to secure hex Bushings in mandrel extrusion (2)
1/8” x ½ “ Spring Pin (6)
¼ “ x 1” Spring Pin (6)
D105 022.4 Adj Hex Adaptor w/ 1/8” x ¾” Spring Pin
D105 004.4 Stop Collar - Core Chuck Style (common to all Industrial, Digital, and Econocraft series laminators, 4 per machine)
PRK184 Plastic Thumbscrew (1 per stop collar)
3/8” dia x 1” Delrin rod inserts (standard, 2 per collar)
Stop Collar shown here in suggested operational position
