Lithonia 4BEMW LED 30K M6 Specs
Catalog Number Notes
FEATURES & SPECIFICATIONS
Type
INTENDED USE — Our recessed LED module is the most economical means to create a well lit environment with exceptional energy efficiency and near zero maintenance. Great for retrofit into existing downlight cans or new construction and remodel applications. Compliant friction clip retention allows fitment into nearly 100% of installed cans. The LED module maintains at least 70% light output for 35,000 hours. Indoor and Outdoor Use.
LED Recessed Downlighting
CONSTRUCTION — Aluminum spun reflector with deep baffle configuration for reduced glare. Combined LED and driver printed circuit board attached. Inner reflector cone funnels light through the pressed-in diffused lens.
4BE
OPTICS — Diffused lens at end of mixing chamber to provide even light distribution for general illumination, equivalent to 65W BR30 Lamp. Wide flood beam angle at > 45°.
4” LED Module IC/Non-IC Retrofit
ELECTRICAL — Center 2 Edge™ (patent pending) technology created for a single point source. Primary power disconnect provided for simple connection to a dedicated LED connector in the housing. Dimming down to 10%. For compatible dimmers, refer to Compatible Dimmers Chart. 600L-lumen E series has an input wattage of 10.3 watts, 58 lumens per watt, equivalent to 65-watt incandescent.
D I
LE
MAB M
E Series' patent pending driver has zero inrush which allows power loads to be calculated with actual rated wattages. Example: 65 units of 4BEMW LED fixtures can be installed in line with a 600-watt dimmer. 600W/10.3W = 65 fixtures. INSTALLATION — Suitable for installation in standard height rough-in sections. E26 adaptor (included)
E26 socket adapter and ships standard. Friction clips allow fitment into cans with an inside diameter of 4.0” to 4.5". LISTINGS — CSA certified to US and Canadian safety standards. ENERGY STAR® certified. Wet location listed. WSEC ASTM E283 for Air-Tight (with IC housings). WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx NOTE: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25°C. Specifications subject to change without notice. PATENTS PENDING.
2-1/2 (6.3)
Specifications Aperture: 4-1/8 (10.5) Ceiling opening: Determined by rough-in Overlap trim: 5-1/4 (13.3) Height: 2-1/2 (6.3)
4-1/8 (10.5) 5-1/4 (13.3)
All dimensions are inches (centimeters) unless otherwise indicated.
ORDERING INFORMATION
Example: 4BEMW LED 27K L3LED T24
All configurations of this product are considered "standard" and have short lead times. LED
Series/Finish
Lamp
CCT / CRI / W / Lumens1
Voltage
4BEMW
LED
27K 30K 40K 50K 27K 90CRI 30K 90CRI 40K 90CRI
(blank)
4" Baffle LED module, matte white
2700K / 82CRI / 10.3W / 530L 3000K / 82CRI / 10.3W / 570L 4000K / 82CRI / 10.3W / 600L 5000K / 81CRI / 9.0W / 660L 2700K / 90CRI / 9.77W / 600L 3000K / 90CRI / 9.71W / 630L 4000K / 90CRI / 9.6W / 640L
Housing Options 120V
L3LED T24 L3RLED T24 L3 L3R
4" new construction rough-in LED base 4" remodel rough-in LED base 4"new construction rough-in 2 4" remodel rough-in 2
Notes 1 Total system delivered lumens. 2 Must be ordered on a separate line.
DOWNLIGHTING
4BE LED
4” LED Module PHOTOMETRICS Distribution Curve Distribution Data Output Data Coefficient of Utilization
Illuminance Data at 30” Above Floor for a Single Luminaire
of Utilization 4BEMW LED, 27K, input watts: 11.9, delivered lumens: 623, LM/W = p52, test no.Coefficients LTL26509, tested in accordance with IESNA LM 79-0 f 20%
60°
200 40°
25 35 45 55 60°65 75 85 90
200 0°
20°
40°
Ave 28 0 79296 5 116 295 129 15 281 117 25 85252 35 46208 45 18152 55 5 96 65 45 75 16 85 4 90 0
pc 80% pf Zone Lumens % Lamp pw 50% 30% 10% pc 0° - 30° 222.8 35.8 119 119 119 0 Zone 56.6Lumens1 % Lamp Lumens 0° - 40° 352.3 pw 107 103 100 0° - 60° 554.7 0° - 30°89.1 222.8 2 35.895 89 84 0 100.0352.3 3 56.6 85 78 72 0° - 40° 280° - 90° 622.6 1 90° - 180° 0.0 0.0 0° - 60° 554.7 4 89.176 68 62 79 2 0° - 180° 622.6 *100.0 69 61 55 5 0° - 90° 622.6 6 100.0 116 3 *Efficiency 63 54 48 90° - 180° 0.0 7 0.057 49 43 129 4 0° - 180° 622.6 8 *100.0 117 52 44 39 5 35 41 48 9 *Efficiency 85 6 45 37 32 10 46 7
RCR
0 5
80°15
Lumens
RCR
80°
Ave 296 295 281 252 208 152 96 45 16 4 0
18 5
8 9 10
Coefficients of Utilization
70% 50% 2010% % 50% 30% 10% 50% 30% 10% beam 80% 70% 50% 50% beam 111 111 111 116 116 116 101.9° 50%101 30% 50% 30% 10%60.7° 95 10% 98 30% 9810% 100 50% 104 Inital FC 50% beam 81 85 90 83 88 93 111 111 111 116 116 116 119 119 119 Mounting Center 75 70 83 60.7° 100 98 95 101 98 1077710371100 80 104 Height Beam Diameter FC Diameter FC 72 66 61 75 68 62 Inital FC 909.8 85 81 93 88 83 8.0 95 89 84 1.0 13.6 4.9 6.4 66 59 54 68 60 54 Mounting Center 805.3 75 70 77 71 10.0 85 547848 72 60 83 0.5 18.5 2.6 8.8 53 48 62 Height Diameter FC 0.3 23.4 Beam 1.6 61 723.3 66 11.1 68 62 12.0 76 496843 62 55 75 48 43 56 4.9 6.4 0.2 1.1 8.0 28.3 9.8 44 39 52 54 662.2 59 13.5 60 54 14.0 69 446139 55 50 68 0.2 0.810.033.3 5.3 15.8 1.6 16.0 2.6 8.8 35 40 47 35 40 48 60 53 48 62 54 48 63 54 48 37 32 44 1.6 11.1 3.3 12.0 55 48 43 49 43 57 374932 43 43 56
52 48 44
39 35 32
44 41 37
52 48 45
44 40 37
50 47 43
39 35 32
44 40 37
1.1 0.8
13.5 15.8
2.2 1.6
14.0 16.0
39 35 32
10% beam 101.9° Diameter 13.6 18.5 23.4 28.3 33.3
FC 1.0 0.5 0.3 0.2 0.2
4BEMW LED, 30K, in accordance with IESNA LM 79-08 0° 20° input watts: 10.8, delivered lumens: 621, LM/W = 58, pf test no. LTL26510, tested 20%
200
0°
20°
40°
RCR
200
pc 80% pf Zone Lumens % Lamp Ave Lumens pw 50% 30% 10% 0° - 30° 221.7 35.7 293 119 119 119 pc 0 0° - 40° 350.8 292 28 100 107 103 pw Zone 56.4 Lumens 1% Lamp Ave Lumens 0° - 60° 552.6 2790 293 79 0° - 30° 88.9221.7 2 35.7 95 89 084 0° - 90° 621.4 100.0 251 115 85 78 72 3 - 40° 350.8 56.4 5 129 292 2890° - 180° 0° 1 0.0 0.0 207 76 68 62 4 0° - 60°*100.0 552.6 5 88.9 69 61 255 279 790° - 180° 621.4 15215 117 0° - 90° 621.4 6 100.062 54 348 115 *Efficiency 9525 251 85 4635 207 46 7 0.0 57 49 443 90° - 180° 0.0 129 1645 152 18 0° - 180° 621.4 8 *100.052 44 539 117 4 5 48 41 35 *Efficiency 9 55 95 85 6 0 45 37 32 10 RCR
0 5 15 80° 25 35 60° 45 55 65 60° 75 85 90 40°
80°
65 75 85 90
46 16 4 0
46 18 5
7 8 9 10
70% 50% 30% 10% 116 116 80%116 104 101 50% 30% 98 10% 88 83 93 119 119 119 83 77 71 103 100 107 75 68 62 89 5484 95 68 60 78 4872 85 62 54 56 49 68 4362 76 44 52 69 61 3955 48 40 35 54 48 62 44 37 32
57 52 48 45
49 44 41 37
43 39 35 32
50% 20% 50% 30% 10% 10% beam 111 111 11170% 50% 50% beam 102.0° 95 10% 97 30% 10050% 50% 30% 10% 61.0° Inital FC 81 116 85 116 90116 50% beam 111 111 111 Mounting Center 80 75 70 61.0° 95 97 Diameter 104 101 98 Height 100 Beam FC Diameter FC 72 66 61 Inital FC 1.0 13.6 4.8 54 83 8.0 90 9.785 816.5 59 88 66 93 Mounting 0.5 18.5Center 2.6 48 71 10.0 80 5.275 708.8 53 77 60 83 0.3 Diameter FC 1.6 11.2 Height23.5Beam 43 62 12.0 72 3.266 61 48 68 55 75 1.1 13.5 39 54 14.0 66 2.259 54 44 60 50 68 4.8 6.5 8.0 28.4 9.70.2 0.2 33.3 0.8 15.9 1.6 16.0 47 40 35
62 43 37 56 52 48 44
54 32 49 44 40 37
48 43 39 35 32
60 55 50 47 43
53 48 44 40 37
48 43 39 35 32
10.0 12.0 14.0 16.0
5.2 3.2 2.2 1.6
8.8 11.2 13.5 15.9
2.6 1.6 1.1 0.8
10% beam 102.0° Diameter 13.6 18.5 23.5 28.4 33.3
FC 1.0 0.5 0.3 0.2 0.2
4BEMW LED, 20° 40K, 10.8, delivered lumens: 663, LM/W = 61, test no. LTL26511, tested in accordance with IESNA LM 79-08 0°
200 40°
200 0°
20°
40°
RCR
60°
0 5 15 80° 25 35 45 55 60°65 75 85 90
RCR
80°
pf pc 80% pf Zone Lumens % Lamp Ave Lumens pw 50% 30% 10% pc 0° - 30° 237.4 35.8 315 119 119 119 0 Zone 56.6Lumens1 % Lamp Ave Lumens pw 0° - 40° 375.4 314 30 107 103 100 0° - 60° 590.5 299 0 84 0° - 30°89.1237.4 2 35.895 89 84 315 0 269 5 124 0° - 40°100.0375.4 3 56.685 78 72 314 300° - 90° 662.9 1 90° - 180° 0.0 0.0 221 138 76 68 62 4 0° - 60° 590.5 89.1 15 299 84 2 0° - 180° 662.9 *100.0 162 124 69 61 55 5 0° - 90° 662.9 6 100.0 269 124 3 *Efficiency 102 25 91 63 54 48 90° 180° 0.0 0.0 35 221 138 4 49 49 57 49 43 7 0° - 180° 662.9 8 *100.0 162 124 17 45 19 5 52 44 39 4 55 5 35 41 48 9 *Efficiency 102 91 6 0 65 49 45 37 32 10 49 7
75 85 90
17 4 0
19 5
8 9 10
20% 70% 50% 20% 50% 30% 10% 50% 30% 10% 80% 50% 50% beam 10% beam 111 111 111 70% 116 116 116 101.8° 50%101 30%9810% 10050% 50% 30% 10%60.8° 95 10% 98 30% 104 Inital111 FC 111 50% beam 81 116 85 116 93 111 11983119 90 116 119 88 Mounting Center 70 75 101 83 60.8° 100 98 95 98 10371100 80 104 107 77 Height Beam Diameter FC Diameter FC 73 66 61 75 68 62 Inital FC 9010.485 81 93 88 83 8.0 95 89 84 1.0 13.5 5.2 6.4 66 59 54 68 60 54 Mounting Center 77 71 10.0 805.675 70 85 5478 4872 0.6 18.4 2.8 8.8 53 48 60 83 62 Height23.4 Beam 0.4 Diameter FC 1.7 11.1 68 62 12.0 733.566 61 76 4968 4362 48 43 55 75 56 5.2 6.4 0.2 1.28.0 28.3 10.4 13.5 60 54 14.0 662.459 54 69 4461 3955 44 39 50 68 52 0.2 33.2 0.9 15.8 1.7 16.0 2.8 8.8 5.6 10.0 35 40 47 35 40 48 60 53 48 62 54 48 63 54 48 37 32 43 56 44 1.7 11.1 3.5 12.0 55 48 43 49 43 57 3749 3243
52 48 45
44 41 37
39 35 32
52 48 44
44 40 37
39 35 32
50 47 43
44 40 37
39 35 32
14.0 16.0
2.4 1.7
13.5 15.8
1.2 0.9
10% beam 101.8° Diameter 13.5 18.4 23.4 28.3 33.2
FC 1.0 0.6 0.4 0.2 0.2
0° 20° 90CRI, input watts: 9.28, delivered lumens:590, LM/W=64, test no. LTL28948P1,tested in accordance with IESNA LM79-08 4BEMW LED, 27K,
4BEMW LED, 30K, 90CRI, input watts: 9.7, delivered lumens: 625, LM/W=64, test no.LTL28947P1, tested in accordance with IESNA LM79-08
DOWNLIGHTING: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4935 Fax: 770-860-3129 www.lithonia.com
4BE LED
© 2014-2016 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/29/16
4” LED Module PHOTOMETRICS Distribution Curve Distribution Data Output Data Coefficient of Utilization
Illuminance Data at 30” Above Floor for a Single Luminaire
Coefficients of Utilization
4BEMW LED, 40K, input watts: 9.63, delivered lumens: 640, LM/W = 66.46, test no. ISF30028, pf 20% tested in accordance with IESNA LM79-08 Coefficients of Utilization
RCR
60°
RCR
80°
pc 80% f Zone Lumens % Lamp Ave Lumens pw 50% 30% p10% 0° - 30° 36.6 234.6 0 310 0 119 119 pc 119 0° - 40° 369.2 29 5 309 107 103pw 100 Zone 57.7 Lumens 1% Lamp Ave Lumens 0° - 60° 571.6 83 15 297 0° - 30° 89.3234.6 2 36.6 95 89 084 310 80° 25 266 0 122 0° - 90° 640.0 100.0 3 85 78 72 0° - 40° 57.7 369.2 29 5 309 1 0.0 0.0 90° - 180° 35 216 135 4 77 69 63 0° - 60°*100.0 571.6 5 89.3 69 61 255 297 830° - 180° 640.0 45 15415 119 0° - 90° 640.0 6 100.063 55 349 122 *Efficiency 55 93 25 266 84 0.0 90° - 180° 45 135 7 0.0 58 49 444 60° 65 45 35 216 75 17 45 154 18 119 0° - 180° 640.0 8*100.053 45 540 85 4 55 5 49 41 636 *Efficiency 9 93 84 90 0 10 45 38 33
200 40°
200 0°
20°
65 75 85 90
40°
45 17 4 0
45 18 5
7 8 9 10
70% 50% 30% 10% 116 80% 116 116 104 30% 101 10% 98 50% 93 88 83 119 119 119 84 77 72 107 103 100 75 68 62 95 89 55 84 68 61 85 78 49 72 62 54 57 49 77 69 44 63 52 45 69 61 39 55 48 41 36 63 55 49 45 38 33
58 53 49 45
49 45 41 38
44 40 36 33
50% 20%10% 50% 30% 50% beam 10% beam 111 11170% 111 50% 101.0° 100 9830% 95 10% 50% 50% 30% 10% 60.7° Inital FC 90116 85116 82 116 50% beam 111Center 111 111 Mounting 81 75 70 60.7° 104 101 98 Height100Beam 98 95 Diameter FC Diameter FC 73 67 62 Inital FC 85 82 6.4 8.0 90 10.2 5.1 13.3 1.0 669359 88 54 83 Mounting Center 2.8 18.2 0.5 75 70 8.8 608453 77 48 72 10.0 81 5.5 Beam0.3 Diameter FC 1.7 23.0 557548 68 43 62 12.0 73 3.4 67 6211.1 Height 1.2 8.0 27.910.2 0.2 6.4 5.1 516844 61 39 55 14.0 66 2.3 59 5413.5 16.0 1.7 15.8 0.9 32.75.5 0.2 47 40 36 10.0 8.8 2.8
62 54 37 33 57 49 52 45 48 41 45 38
44
49 44 39 36 33
60 55 51 47 44
53 48 44 40 37
48 43 39 36 33
12.0 14.0 16.0
3.4 2.3 1.7
11.1 13.5 15.8
1.7 1.2 0.9
10% beam 101.0° Diameter 13.3 18.2 23.0 27.9 32.7
FC 1.0 0.5 0.3 0.2 0.2
Coefficients of Utilization 4BEMW LED, 20° 50K, input watts: 9, delivered lumens: 648, LM/W = 72.22, in accordance with IESNA LM79-08 pf test no. ISF29994, tested 20% 0°
200 40°
200 0°
0°
20°
40°
pc 80% Zone Lumens % Lamp Ave Lumens pw 50% 30% p 10% f 0° - 30° 36.5 240.8 317 0 119 119 pc 119 0° - 40° 57.7 380.0 317 30 1 107 103 100 Zone Lumens % Lamp Ave Lumens pw 0° - 60° 588.8 89.4 302 85 2 95 89 84 0° - 30° 100.0 240.8 3 36.5 85 78 072 317 0° - 90° 658.9 275 0 126 317 3090° - 180° 0° 0.0- 40° 0.0380.0 4 57.7 77 69 163 223 5 139 0° - 60°*100.0 588.8 5 89.4 69 61 255 302 850° - 180° 658.9 15915 123 *Efficiency 96 25 86 0° - 90° 658.9 6 100.063 55 349 275 126 46 35 46 7 0.0 57 49 444 0.0 90° - 180° 223 139 16 19 45 159 123 0° - 180° 658.9 8*100.053 45 540 4 5 9 49 41 36 *Efficiency 55 96 86 6 0 10 45 38 33
RCR
60°
0 5 15 80° 25 35 45 55 65 60° 75 85 90
RCR
80°
65 75 85 90
46 16 4 0
46 19 5
7 8 9 10
20°
ADDITIONAL DATA 4BEMW LED 27K ENERGY DATA* CRI - 82 Lumens 530L Min. starting temp -18°C (0°F) Max. temp 46°C (115°F) EMI/RFI FCC Title 47 CFR, Part 15, Class B Sound rating A standards Input voltage 120V Min. power factor 0.99 Input frequency 50/60 Hz Rated wattage 10.3W Input power 10.3W Input current .11A *Values at non-dimming line voltage.
Utilization 70%Coefficients of 50% 50% 30% 10% 50% 30% 20%10% 50% beam 10% beam 116 80% 116 116 111 11170% 111 50% 61.2° 101.1° 104 101 98 100 98 95 50% 30% 10% 50% 30% 10% 50% 30% 10% Inital FC 93 88 83 90 85 82 50% beam 119 119 111Center 111 111 84 119 77 72 81116 75 116 70 116Mounting 61.2° 107 100 98 95 Diameter FC Diameter FC 75 103 68 62 73104 67 101 62 98 Height100Beam Inital FC 5.2 13.4 1.0 95 89 55 84 85 82 6.5 68 61 66 9359 88 54 83 8.0 90 10.5 2.8 18.2 0.6 Center 62 54 60 8453 77 48 72 10.0 81 5.6 85 78 49 72 75 70 8.9 Mounting 11.2 1.8 23.1 57 49 55 7548 68 43 62 12.0 73 3.5 Height Beam0.3 Diameter FC 77 69 44 63 67 62 14.0 2.4 13.6 1.2 52 45 39 51 44 39 8.0 28.010.5 0.2 6.5 5.2 69 61 55 68 61 55 16.0 66 1.7 59 5416.0 0.9 32.8 0.2 48 41 36 47 40 36 63 45 57 53 49 45
55 49 38 33 49 44 45 40 41 36 38 33
62 44 37 57 52 48 45
54 33 49 45 41 38
49 44 39 36 33
ADDITIONAL DATA 4BEMW LED 30K ENERGY DATA*
CRI - 90 600L
9.71W 9.71W
CRI - 82 Lumens 570L Min. starting temp -18°C (0°F) Max. temp 46°C (115°F) EMI/RFI FCC Title 47 CFR, Part 15, Class B Sound rating A standards Input voltage 120V Min. power factor 0.99 Input frequency 50/60 Hz Rated wattage 10.3W Input power 10.3W Input current .11A *Values at non-dimming line voltage.
DOWNLIGHTING: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4935 Fax: 770-860-3129 www.lithonia.com
60 55 51 47 44
53 48 44 40 37
48 43 39 36 33
10.0 12.0 14.0 16.0
5.6 3.5 2.4 1.7
8.9 11.2 13.6 16.0
2.8 1.8 1.2 0.9
10% beam 101.1° Diameter 13.4 18.2 23.1 28.0 32.8
FC 1.0 0.6 0.3 0.2 0.2
ADDITIONAL DATA 4BEMW LED 40K ENERGY DATA*
CRI - 90 600L
9.71W 9.71W
CRI - 82 Lumens 600L Min. starting temp -18°C (0°F) Max. temp 46°C (115°F) EMI/RFI FCC Title 47 CFR, Part 15, Class B Sound rating A standards Input voltage 120V Min. power factor 0.99 Input frequency 50/60 Hz Rated wattage 10.3W Input power 10.3W Input current .11A *Values at non-dimming line voltage.
4BE LED
© 2014-2016 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/29/16
4” LED Module LIGHTING FACTS
DOWNLIGHTING: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4935 Fax: 770-860-3129 www.lithonia.com
4BE LED
© 2014-2016 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/29/16
FEATURES & SPECIFICATIONS
Type
INTENDED USE — Our recessed LED module is the most economical means to create a well lit environment with exceptional energy efficiency and near zero maintenance. Great for retrofit into existing downlight cans or new construction and remodel applications. Compliant friction clip retention allows fitment into nearly 100% of installed cans. The LED module maintains at least 70% light output for 35,000 hours. Indoor and Outdoor Use.
LED Recessed Downlighting
CONSTRUCTION — Aluminum spun reflector with deep baffle configuration for reduced glare. Combined LED and driver printed circuit board attached. Inner reflector cone funnels light through the pressed-in diffused lens.
4BE
OPTICS — Diffused lens at end of mixing chamber to provide even light distribution for general illumination, equivalent to 65W BR30 Lamp. Wide flood beam angle at > 45°.
4” LED Module IC/Non-IC Retrofit
ELECTRICAL — Center 2 Edge™ (patent pending) technology created for a single point source. Primary power disconnect provided for simple connection to a dedicated LED connector in the housing. Dimming down to 10%. For compatible dimmers, refer to Compatible Dimmers Chart. 600L-lumen E series has an input wattage of 10.3 watts, 58 lumens per watt, equivalent to 65-watt incandescent.
D I
LE
MAB M
E Series' patent pending driver has zero inrush which allows power loads to be calculated with actual rated wattages. Example: 65 units of 4BEMW LED fixtures can be installed in line with a 600-watt dimmer. 600W/10.3W = 65 fixtures. INSTALLATION — Suitable for installation in standard height rough-in sections. E26 adaptor (included)
E26 socket adapter and ships standard. Friction clips allow fitment into cans with an inside diameter of 4.0” to 4.5". LISTINGS — CSA certified to US and Canadian safety standards. ENERGY STAR® certified. Wet location listed. WSEC ASTM E283 for Air-Tight (with IC housings). WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx NOTE: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25°C. Specifications subject to change without notice. PATENTS PENDING.
2-1/2 (6.3)
Specifications Aperture: 4-1/8 (10.5) Ceiling opening: Determined by rough-in Overlap trim: 5-1/4 (13.3) Height: 2-1/2 (6.3)
4-1/8 (10.5) 5-1/4 (13.3)
All dimensions are inches (centimeters) unless otherwise indicated.
ORDERING INFORMATION
Example: 4BEMW LED 27K L3LED T24
All configurations of this product are considered "standard" and have short lead times. LED
Series/Finish
Lamp
CCT / CRI / W / Lumens1
Voltage
4BEMW
LED
27K 30K 40K 50K 27K 90CRI 30K 90CRI 40K 90CRI
(blank)
4" Baffle LED module, matte white
2700K / 82CRI / 10.3W / 530L 3000K / 82CRI / 10.3W / 570L 4000K / 82CRI / 10.3W / 600L 5000K / 81CRI / 9.0W / 660L 2700K / 90CRI / 9.77W / 600L 3000K / 90CRI / 9.71W / 630L 4000K / 90CRI / 9.6W / 640L
Housing Options 120V
L3LED T24 L3RLED T24 L3 L3R
4" new construction rough-in LED base 4" remodel rough-in LED base 4"new construction rough-in 2 4" remodel rough-in 2
Notes 1 Total system delivered lumens. 2 Must be ordered on a separate line.
DOWNLIGHTING
4BE LED
4” LED Module PHOTOMETRICS Distribution Curve Distribution Data Output Data Coefficient of Utilization
Illuminance Data at 30” Above Floor for a Single Luminaire
of Utilization 4BEMW LED, 27K, input watts: 11.9, delivered lumens: 623, LM/W = p52, test no.Coefficients LTL26509, tested in accordance with IESNA LM 79-0 f 20%
60°
200 40°
25 35 45 55 60°65 75 85 90
200 0°
20°
40°
Ave 28 0 79296 5 116 295 129 15 281 117 25 85252 35 46208 45 18152 55 5 96 65 45 75 16 85 4 90 0
pc 80% pf Zone Lumens % Lamp pw 50% 30% 10% pc 0° - 30° 222.8 35.8 119 119 119 0 Zone 56.6Lumens1 % Lamp Lumens 0° - 40° 352.3 pw 107 103 100 0° - 60° 554.7 0° - 30°89.1 222.8 2 35.895 89 84 0 100.0352.3 3 56.6 85 78 72 0° - 40° 280° - 90° 622.6 1 90° - 180° 0.0 0.0 0° - 60° 554.7 4 89.176 68 62 79 2 0° - 180° 622.6 *100.0 69 61 55 5 0° - 90° 622.6 6 100.0 116 3 *Efficiency 63 54 48 90° - 180° 0.0 7 0.057 49 43 129 4 0° - 180° 622.6 8 *100.0 117 52 44 39 5 35 41 48 9 *Efficiency 85 6 45 37 32 10 46 7
RCR
0 5
80°15
Lumens
RCR
80°
Ave 296 295 281 252 208 152 96 45 16 4 0
18 5
8 9 10
Coefficients of Utilization
70% 50% 2010% % 50% 30% 10% 50% 30% 10% beam 80% 70% 50% 50% beam 111 111 111 116 116 116 101.9° 50%101 30% 50% 30% 10%60.7° 95 10% 98 30% 9810% 100 50% 104 Inital FC 50% beam 81 85 90 83 88 93 111 111 111 116 116 116 119 119 119 Mounting Center 75 70 83 60.7° 100 98 95 101 98 1077710371100 80 104 Height Beam Diameter FC Diameter FC 72 66 61 75 68 62 Inital FC 909.8 85 81 93 88 83 8.0 95 89 84 1.0 13.6 4.9 6.4 66 59 54 68 60 54 Mounting Center 805.3 75 70 77 71 10.0 85 547848 72 60 83 0.5 18.5 2.6 8.8 53 48 62 Height Diameter FC 0.3 23.4 Beam 1.6 61 723.3 66 11.1 68 62 12.0 76 496843 62 55 75 48 43 56 4.9 6.4 0.2 1.1 8.0 28.3 9.8 44 39 52 54 662.2 59 13.5 60 54 14.0 69 446139 55 50 68 0.2 0.810.033.3 5.3 15.8 1.6 16.0 2.6 8.8 35 40 47 35 40 48 60 53 48 62 54 48 63 54 48 37 32 44 1.6 11.1 3.3 12.0 55 48 43 49 43 57 374932 43 43 56
52 48 44
39 35 32
44 41 37
52 48 45
44 40 37
50 47 43
39 35 32
44 40 37
1.1 0.8
13.5 15.8
2.2 1.6
14.0 16.0
39 35 32
10% beam 101.9° Diameter 13.6 18.5 23.4 28.3 33.3
FC 1.0 0.5 0.3 0.2 0.2
4BEMW LED, 30K, in accordance with IESNA LM 79-08 0° 20° input watts: 10.8, delivered lumens: 621, LM/W = 58, pf test no. LTL26510, tested 20%
200
0°
20°
40°
RCR
200
pc 80% pf Zone Lumens % Lamp Ave Lumens pw 50% 30% 10% 0° - 30° 221.7 35.7 293 119 119 119 pc 0 0° - 40° 350.8 292 28 100 107 103 pw Zone 56.4 Lumens 1% Lamp Ave Lumens 0° - 60° 552.6 2790 293 79 0° - 30° 88.9221.7 2 35.7 95 89 084 0° - 90° 621.4 100.0 251 115 85 78 72 3 - 40° 350.8 56.4 5 129 292 2890° - 180° 0° 1 0.0 0.0 207 76 68 62 4 0° - 60°*100.0 552.6 5 88.9 69 61 255 279 790° - 180° 621.4 15215 117 0° - 90° 621.4 6 100.062 54 348 115 *Efficiency 9525 251 85 4635 207 46 7 0.0 57 49 443 90° - 180° 0.0 129 1645 152 18 0° - 180° 621.4 8 *100.052 44 539 117 4 5 48 41 35 *Efficiency 9 55 95 85 6 0 45 37 32 10 RCR
0 5 15 80° 25 35 60° 45 55 65 60° 75 85 90 40°
80°
65 75 85 90
46 16 4 0
46 18 5
7 8 9 10
70% 50% 30% 10% 116 116 80%116 104 101 50% 30% 98 10% 88 83 93 119 119 119 83 77 71 103 100 107 75 68 62 89 5484 95 68 60 78 4872 85 62 54 56 49 68 4362 76 44 52 69 61 3955 48 40 35 54 48 62 44 37 32
57 52 48 45
49 44 41 37
43 39 35 32
50% 20% 50% 30% 10% 10% beam 111 111 11170% 50% 50% beam 102.0° 95 10% 97 30% 10050% 50% 30% 10% 61.0° Inital FC 81 116 85 116 90116 50% beam 111 111 111 Mounting Center 80 75 70 61.0° 95 97 Diameter 104 101 98 Height 100 Beam FC Diameter FC 72 66 61 Inital FC 1.0 13.6 4.8 54 83 8.0 90 9.785 816.5 59 88 66 93 Mounting 0.5 18.5Center 2.6 48 71 10.0 80 5.275 708.8 53 77 60 83 0.3 Diameter FC 1.6 11.2 Height23.5Beam 43 62 12.0 72 3.266 61 48 68 55 75 1.1 13.5 39 54 14.0 66 2.259 54 44 60 50 68 4.8 6.5 8.0 28.4 9.70.2 0.2 33.3 0.8 15.9 1.6 16.0 47 40 35
62 43 37 56 52 48 44
54 32 49 44 40 37
48 43 39 35 32
60 55 50 47 43
53 48 44 40 37
48 43 39 35 32
10.0 12.0 14.0 16.0
5.2 3.2 2.2 1.6
8.8 11.2 13.5 15.9
2.6 1.6 1.1 0.8
10% beam 102.0° Diameter 13.6 18.5 23.5 28.4 33.3
FC 1.0 0.5 0.3 0.2 0.2
4BEMW LED, 20° 40K, 10.8, delivered lumens: 663, LM/W = 61, test no. LTL26511, tested in accordance with IESNA LM 79-08 0°
200 40°
200 0°
20°
40°
RCR
60°
0 5 15 80° 25 35 45 55 60°65 75 85 90
RCR
80°
pf pc 80% pf Zone Lumens % Lamp Ave Lumens pw 50% 30% 10% pc 0° - 30° 237.4 35.8 315 119 119 119 0 Zone 56.6Lumens1 % Lamp Ave Lumens pw 0° - 40° 375.4 314 30 107 103 100 0° - 60° 590.5 299 0 84 0° - 30°89.1237.4 2 35.895 89 84 315 0 269 5 124 0° - 40°100.0375.4 3 56.685 78 72 314 300° - 90° 662.9 1 90° - 180° 0.0 0.0 221 138 76 68 62 4 0° - 60° 590.5 89.1 15 299 84 2 0° - 180° 662.9 *100.0 162 124 69 61 55 5 0° - 90° 662.9 6 100.0 269 124 3 *Efficiency 102 25 91 63 54 48 90° 180° 0.0 0.0 35 221 138 4 49 49 57 49 43 7 0° - 180° 662.9 8 *100.0 162 124 17 45 19 5 52 44 39 4 55 5 35 41 48 9 *Efficiency 102 91 6 0 65 49 45 37 32 10 49 7
75 85 90
17 4 0
19 5
8 9 10
20% 70% 50% 20% 50% 30% 10% 50% 30% 10% 80% 50% 50% beam 10% beam 111 111 111 70% 116 116 116 101.8° 50%101 30%9810% 10050% 50% 30% 10%60.8° 95 10% 98 30% 104 Inital111 FC 111 50% beam 81 116 85 116 93 111 11983119 90 116 119 88 Mounting Center 70 75 101 83 60.8° 100 98 95 98 10371100 80 104 107 77 Height Beam Diameter FC Diameter FC 73 66 61 75 68 62 Inital FC 9010.485 81 93 88 83 8.0 95 89 84 1.0 13.5 5.2 6.4 66 59 54 68 60 54 Mounting Center 77 71 10.0 805.675 70 85 5478 4872 0.6 18.4 2.8 8.8 53 48 60 83 62 Height23.4 Beam 0.4 Diameter FC 1.7 11.1 68 62 12.0 733.566 61 76 4968 4362 48 43 55 75 56 5.2 6.4 0.2 1.28.0 28.3 10.4 13.5 60 54 14.0 662.459 54 69 4461 3955 44 39 50 68 52 0.2 33.2 0.9 15.8 1.7 16.0 2.8 8.8 5.6 10.0 35 40 47 35 40 48 60 53 48 62 54 48 63 54 48 37 32 43 56 44 1.7 11.1 3.5 12.0 55 48 43 49 43 57 3749 3243
52 48 45
44 41 37
39 35 32
52 48 44
44 40 37
39 35 32
50 47 43
44 40 37
39 35 32
14.0 16.0
2.4 1.7
13.5 15.8
1.2 0.9
10% beam 101.8° Diameter 13.5 18.4 23.4 28.3 33.2
FC 1.0 0.6 0.4 0.2 0.2
0° 20° 90CRI, input watts: 9.28, delivered lumens:590, LM/W=64, test no. LTL28948P1,tested in accordance with IESNA LM79-08 4BEMW LED, 27K,
4BEMW LED, 30K, 90CRI, input watts: 9.7, delivered lumens: 625, LM/W=64, test no.LTL28947P1, tested in accordance with IESNA LM79-08
DOWNLIGHTING: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4935 Fax: 770-860-3129 www.lithonia.com
4BE LED
© 2014-2016 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/29/16
4” LED Module PHOTOMETRICS Distribution Curve Distribution Data Output Data Coefficient of Utilization
Illuminance Data at 30” Above Floor for a Single Luminaire
Coefficients of Utilization
4BEMW LED, 40K, input watts: 9.63, delivered lumens: 640, LM/W = 66.46, test no. ISF30028, pf 20% tested in accordance with IESNA LM79-08 Coefficients of Utilization
RCR
60°
RCR
80°
pc 80% f Zone Lumens % Lamp Ave Lumens pw 50% 30% p10% 0° - 30° 36.6 234.6 0 310 0 119 119 pc 119 0° - 40° 369.2 29 5 309 107 103pw 100 Zone 57.7 Lumens 1% Lamp Ave Lumens 0° - 60° 571.6 83 15 297 0° - 30° 89.3234.6 2 36.6 95 89 084 310 80° 25 266 0 122 0° - 90° 640.0 100.0 3 85 78 72 0° - 40° 57.7 369.2 29 5 309 1 0.0 0.0 90° - 180° 35 216 135 4 77 69 63 0° - 60°*100.0 571.6 5 89.3 69 61 255 297 830° - 180° 640.0 45 15415 119 0° - 90° 640.0 6 100.063 55 349 122 *Efficiency 55 93 25 266 84 0.0 90° - 180° 45 135 7 0.0 58 49 444 60° 65 45 35 216 75 17 45 154 18 119 0° - 180° 640.0 8*100.053 45 540 85 4 55 5 49 41 636 *Efficiency 9 93 84 90 0 10 45 38 33
200 40°
200 0°
20°
65 75 85 90
40°
45 17 4 0
45 18 5
7 8 9 10
70% 50% 30% 10% 116 80% 116 116 104 30% 101 10% 98 50% 93 88 83 119 119 119 84 77 72 107 103 100 75 68 62 95 89 55 84 68 61 85 78 49 72 62 54 57 49 77 69 44 63 52 45 69 61 39 55 48 41 36 63 55 49 45 38 33
58 53 49 45
49 45 41 38
44 40 36 33
50% 20%10% 50% 30% 50% beam 10% beam 111 11170% 111 50% 101.0° 100 9830% 95 10% 50% 50% 30% 10% 60.7° Inital FC 90116 85116 82 116 50% beam 111Center 111 111 Mounting 81 75 70 60.7° 104 101 98 Height100Beam 98 95 Diameter FC Diameter FC 73 67 62 Inital FC 85 82 6.4 8.0 90 10.2 5.1 13.3 1.0 669359 88 54 83 Mounting Center 2.8 18.2 0.5 75 70 8.8 608453 77 48 72 10.0 81 5.5 Beam0.3 Diameter FC 1.7 23.0 557548 68 43 62 12.0 73 3.4 67 6211.1 Height 1.2 8.0 27.910.2 0.2 6.4 5.1 516844 61 39 55 14.0 66 2.3 59 5413.5 16.0 1.7 15.8 0.9 32.75.5 0.2 47 40 36 10.0 8.8 2.8
62 54 37 33 57 49 52 45 48 41 45 38
44
49 44 39 36 33
60 55 51 47 44
53 48 44 40 37
48 43 39 36 33
12.0 14.0 16.0
3.4 2.3 1.7
11.1 13.5 15.8
1.7 1.2 0.9
10% beam 101.0° Diameter 13.3 18.2 23.0 27.9 32.7
FC 1.0 0.5 0.3 0.2 0.2
Coefficients of Utilization 4BEMW LED, 20° 50K, input watts: 9, delivered lumens: 648, LM/W = 72.22, in accordance with IESNA LM79-08 pf test no. ISF29994, tested 20% 0°
200 40°
200 0°
0°
20°
40°
pc 80% Zone Lumens % Lamp Ave Lumens pw 50% 30% p 10% f 0° - 30° 36.5 240.8 317 0 119 119 pc 119 0° - 40° 57.7 380.0 317 30 1 107 103 100 Zone Lumens % Lamp Ave Lumens pw 0° - 60° 588.8 89.4 302 85 2 95 89 84 0° - 30° 100.0 240.8 3 36.5 85 78 072 317 0° - 90° 658.9 275 0 126 317 3090° - 180° 0° 0.0- 40° 0.0380.0 4 57.7 77 69 163 223 5 139 0° - 60°*100.0 588.8 5 89.4 69 61 255 302 850° - 180° 658.9 15915 123 *Efficiency 96 25 86 0° - 90° 658.9 6 100.063 55 349 275 126 46 35 46 7 0.0 57 49 444 0.0 90° - 180° 223 139 16 19 45 159 123 0° - 180° 658.9 8*100.053 45 540 4 5 9 49 41 36 *Efficiency 55 96 86 6 0 10 45 38 33
RCR
60°
0 5 15 80° 25 35 45 55 65 60° 75 85 90
RCR
80°
65 75 85 90
46 16 4 0
46 19 5
7 8 9 10
20°
ADDITIONAL DATA 4BEMW LED 27K ENERGY DATA* CRI - 82 Lumens 530L Min. starting temp -18°C (0°F) Max. temp 46°C (115°F) EMI/RFI FCC Title 47 CFR, Part 15, Class B Sound rating A standards Input voltage 120V Min. power factor 0.99 Input frequency 50/60 Hz Rated wattage 10.3W Input power 10.3W Input current .11A *Values at non-dimming line voltage.
Utilization 70%Coefficients of 50% 50% 30% 10% 50% 30% 20%10% 50% beam 10% beam 116 80% 116 116 111 11170% 111 50% 61.2° 101.1° 104 101 98 100 98 95 50% 30% 10% 50% 30% 10% 50% 30% 10% Inital FC 93 88 83 90 85 82 50% beam 119 119 111Center 111 111 84 119 77 72 81116 75 116 70 116Mounting 61.2° 107 100 98 95 Diameter FC Diameter FC 75 103 68 62 73104 67 101 62 98 Height100Beam Inital FC 5.2 13.4 1.0 95 89 55 84 85 82 6.5 68 61 66 9359 88 54 83 8.0 90 10.5 2.8 18.2 0.6 Center 62 54 60 8453 77 48 72 10.0 81 5.6 85 78 49 72 75 70 8.9 Mounting 11.2 1.8 23.1 57 49 55 7548 68 43 62 12.0 73 3.5 Height Beam0.3 Diameter FC 77 69 44 63 67 62 14.0 2.4 13.6 1.2 52 45 39 51 44 39 8.0 28.010.5 0.2 6.5 5.2 69 61 55 68 61 55 16.0 66 1.7 59 5416.0 0.9 32.8 0.2 48 41 36 47 40 36 63 45 57 53 49 45
55 49 38 33 49 44 45 40 41 36 38 33
62 44 37 57 52 48 45
54 33 49 45 41 38
49 44 39 36 33
ADDITIONAL DATA 4BEMW LED 30K ENERGY DATA*
CRI - 90 600L
9.71W 9.71W
CRI - 82 Lumens 570L Min. starting temp -18°C (0°F) Max. temp 46°C (115°F) EMI/RFI FCC Title 47 CFR, Part 15, Class B Sound rating A standards Input voltage 120V Min. power factor 0.99 Input frequency 50/60 Hz Rated wattage 10.3W Input power 10.3W Input current .11A *Values at non-dimming line voltage.
DOWNLIGHTING: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4935 Fax: 770-860-3129 www.lithonia.com
60 55 51 47 44
53 48 44 40 37
48 43 39 36 33
10.0 12.0 14.0 16.0
5.6 3.5 2.4 1.7
8.9 11.2 13.6 16.0
2.8 1.8 1.2 0.9
10% beam 101.1° Diameter 13.4 18.2 23.1 28.0 32.8
FC 1.0 0.6 0.3 0.2 0.2
ADDITIONAL DATA 4BEMW LED 40K ENERGY DATA*
CRI - 90 600L
9.71W 9.71W
CRI - 82 Lumens 600L Min. starting temp -18°C (0°F) Max. temp 46°C (115°F) EMI/RFI FCC Title 47 CFR, Part 15, Class B Sound rating A standards Input voltage 120V Min. power factor 0.99 Input frequency 50/60 Hz Rated wattage 10.3W Input power 10.3W Input current .11A *Values at non-dimming line voltage.
4BE LED
© 2014-2016 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/29/16
4” LED Module LIGHTING FACTS
DOWNLIGHTING: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4935 Fax: 770-860-3129 www.lithonia.com
4BE LED
© 2014-2016 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/29/16
