Right handlebar support Topsurrpsupsupsupport handlebar
1
40
∮20x∮10.5x1.5 flat washer
6
6
Front handlebar
1
41
M4x15 crosshead bolt
10
7
Running belt
1
42
M8x40 bolt
2
8
emery cloth
2
43
M8 lock num
2
9
Right rail
1
44
M10x50 bolt
2
10
Left rail
1
45
11
Running board
1
46
12
Flywheel cover
1
47
13
Left front end cap
1
48
∮10x∮5.2x1 flat washer
9
14
Left rear end cap
1
49
M5x20 crosshead bolt
1
15
Right rear end cap
1
50
∮16x∮8.5x1.5 arc washer
2
16
Front roller
1
51
M8x35 screw
2
17
Rear roller
1
52
18
Front roller axis
1
53
∮16x∮6.5x1.5 flat washer
8
19
Rear roller axis
1
54
M6x75 bolt
2
20
Foot cushion
2
55
M6 lock nut
6
21
Round end cap
2
56
∮16x∮12.2x1 flat washer
4
22
Transport wheel
2
57
∮24x∮13.2x1 flat washer
4
23
Buffer cushion
4
58
M6x35 screw
6
24
Triangular knob
1
59
M3x10 screw
2
25
hand foam
2
60
M6x45 bolt
1
26
Hand foam
2
61
M6 nut
1
27
Computer
1
62
M6x10 bolt
1
28
Wire connector
1
63
∮13x∮6.5x1.5 flat washer
1
29
Handls pulse sheet
2
64
M4x12 screw
2
30
WireⅠ
1
65
Nut cap 17#
2
31
WireⅡ
1
66
wrench
1
32
Sensor
1
67
Wrench 5#
1
33
Adjustment knob
1
68
Wrench 10#
2
34
Adjustment wire
1
69
M4X12 Screw
2
35
Magnetic
1 3
Left Handlebar cover Right Handlebar cover M4x20 crosshead screw
M5x10 crosshead screw
QYT
2 2 2
2
ASSEMBLY INSTRUCTIONS
Step 1: Attach the flywheel cover(12) to the main frame(1) with two ∮10X∮5.2X1 flat washers（48）and two M5x10 crosshead screws (52). Fix Left front end cap（13） 、Left rear end cap（14） 、Right rear end cap（15）to the main frame（1）with two ∮10x∮5.2x1flat washers（48）and two M4x15 crosshead bolts（41）.
Step 2： 49 48 3
33
Using four ∮ 20x ∮ 10.5x1.5 flat washers(40) and four M10x40 bolts (39) to attache the Base support(2) to Left handlebar support(3) and Right handlebar support(4).
4
36
31
2
40 39
40 40
4
Step 3： Attache the Main frame(1) to the Left handlebar support(3) and Right handlebar support(4) with two ∮20x∮ 10.5x1.5 flat washers （ 40 ） and two M10x50 bolts(44) 3
4
Cover both the M10x50 bolts(44) with Nut caps#17(65).
44 65 40
Attach the Triangular knob(24) to the hole in Left handlebar support(3) Coonect the Wire Ⅱ (31) with Sensor box(32)
32 40 65 44 24
1
50
51 46
Step 4：
30 69 31
5
Attach the top handlebar(5) to the Left handlebar support(3) and Right handlebar support (4) with two handlebar cover（46）and handlebar cover（45）
6
45
3
Connect the Wire Ⅰ (30) in Front handlebar(6) to the WireⅡ(31)；
4
Attach the Front handlebar(6) to the Left handlebar support(3) and Right handlebar support (4) with two ∮16x∮8.5x1.5 arc washers(50) and two M8x35 screws(51) .
5
27
30 28
Step 5： Attache the Computer(6) to the sheet on the Front handlebar(6) with two M4x12 screws(64).
64
Connect the Wire connector(28) to WireⅠand the hole in Computer(27).
Step 6 1. Swith the Adjustment knob(8) to level 1. 2.Put Screw D of Adjustment wire(34)in the hole E； 3. Put A of Adjustment wire(34)in the hole F. Swith the Adjustment knob(8) to level 8. 4.Tighten Adjustment wire(34) until the width between the Magnetic rack(37) and flywheel is 2-3mm.tighten the Screw D with Nut B and C.
最后杆锁紧； 6
■ FUNCTION BUTTONS: 1. MODE: Press it to select functions. 2. SET: Press to set function value as exercise target. 3. RESET: Press to reset function value respectively. ■ FUNCIONS: 1. SCAN: Press MODE button until the arrow appears at SCAN position, computer will rotate through all the functions: Time, Speed, Distance, Calorie, total distance and Pulse (If have). Each function will display for 6 seconds. 2. SPEED: Display current speed. 3. DISTANCE: Count the distance from exercise start to end. 4. TIME: Count the total time from exercise start to end. 5. ODO: Count the total distance after installing the batteries. 6. CAL: Count the total calories from exercise start to end. 7. PULSE (IF HAVE): Display your current heartbeat percent minute when you hold the sensor on the handle. 8. AUTO ON/OFF & AUTO START/STOP: Without any signal for 4 minutes, the power will turn off automatically. As long as the wheel is in motion or any button is pressed , the computer would be in action. NOTE: The computer can be programmed before delivery with Metric or Imperial system. If you find “M” in right side of monitor screen (perhaps on the bottom of the computer or on the carton of computer), it’s with Imperial system and the unit will be Mile. Otherwise, if you find “K”, it’s with Metric system and the unit will be kilometer. ■ SPECIFICATION: FUNCTIONS AUTO SCAN Every 6 seconds TIME 00:00~99:59(Minute: Second) Speed The max pick-up signal is 999.9Km/h or Mile/h Distance 0.00~9999 Km or Mile Calories 0.0~9999Kcal ODO meter 0~9999 Km or Mile Pulse (If have) 40-240 BPM Battery Type 2 pieces of SIZE-AAA Operating Temperature 0℃ ~ +40℃(32℉~104℉) Storage Temperature -10℃ ~ +60℃(14℉~140℉)