MicroSCADA Pro SYS 600C Battery Replacement Guideline
1MRS224148B, June 12, 2012
MicroSCADA Pro SYS 600C Battery Replacement Guideline This guideline describes how to replace the BIOS battery of SYS 600C. The guideline is applicable for SYS 600C versions 1.xx and 2.xx 1. Disconnect the external power supply and loosen the two screws as shown in the picture. Then open the casing;
2. With necessary ESD protection, remove the battery cap by holding the upper corners of the cap and carefully pull it upwards.
ABB Oy Substation Automation Products FI-65100 Vaasa, Finland Tel. +358 10 2211 Fax +358 10 2241599 www.abb.com/substationautomation
1MRS224148B, June 12, 2012
MicroSCADA Pro SYS 600C Battery Replacement Guideline 3. Push the battery holder latch in the direction shown in the picture.
4. Take the battery out from the battery holder.
5. Replace the new battery with a new one (Battery type CR2032), please be noted that the positive polarity side marked with “+” is facing the battery holder latch’s side. ( With multi-meter, Check the Voltage level for the new Battery before changing : Level should be > 2.8V, Standard Voltage is 3.0V) ABB Oy Substation Automation Products FI-65100 Vaasa, Finland Tel. +358 10 2211 Fax +358 10 2241599 www.abb.com/substationautomation
1MRS224148B, June 12, 2012
MicroSCADA Pro SYS 600C Battery Replacement Guideline 6. Put the battery cap back on.
7. Close the casing and fasten the two screws as shown in the step 1. 8. Connect to external power supply, start SYS 600C and press “DEL” to enter the BIOS settings. 9. Select “Load optimized defaults”, press ENTER. 10. Set system time and date in “Standard CMOS Features”. 11. Select “Save & Exit Setup”, press ENTER to exit BIOS settings screen.
Copyright 2012, ABB Oy, Substation Automation Products The information in this document is subject to change without notice and should not be construed as a commitment by ABB Oy, Substation Automation Products. ABB Oy, Substation Automation Products assumes no responsibility for any error that may appear in this document.
ABB Oy Substation Automation Products FI-65100 Vaasa, Finland Tel. +358 10 2211 Fax +358 10 2241599 www.abb.com/substationautomation
MicroSCADA Pro SYS 600C Battery Replacement Guideline This guideline describes how to replace the BIOS battery of SYS 600C. The guideline is applicable for SYS 600C versions 1.xx and 2.xx 1. Disconnect the external power supply and loosen the two screws as shown in the picture. Then open the casing;
2. With necessary ESD protection, remove the battery cap by holding the upper corners of the cap and carefully pull it upwards.
ABB Oy Substation Automation Products FI-65100 Vaasa, Finland Tel. +358 10 2211 Fax +358 10 2241599 www.abb.com/substationautomation
1MRS224148B, June 12, 2012
MicroSCADA Pro SYS 600C Battery Replacement Guideline 3. Push the battery holder latch in the direction shown in the picture.
4. Take the battery out from the battery holder.
5. Replace the new battery with a new one (Battery type CR2032), please be noted that the positive polarity side marked with “+” is facing the battery holder latch’s side. ( With multi-meter, Check the Voltage level for the new Battery before changing : Level should be > 2.8V, Standard Voltage is 3.0V) ABB Oy Substation Automation Products FI-65100 Vaasa, Finland Tel. +358 10 2211 Fax +358 10 2241599 www.abb.com/substationautomation
1MRS224148B, June 12, 2012
MicroSCADA Pro SYS 600C Battery Replacement Guideline 6. Put the battery cap back on.
7. Close the casing and fasten the two screws as shown in the step 1. 8. Connect to external power supply, start SYS 600C and press “DEL” to enter the BIOS settings. 9. Select “Load optimized defaults”, press ENTER. 10. Set system time and date in “Standard CMOS Features”. 11. Select “Save & Exit Setup”, press ENTER to exit BIOS settings screen.
Copyright 2012, ABB Oy, Substation Automation Products The information in this document is subject to change without notice and should not be construed as a commitment by ABB Oy, Substation Automation Products. ABB Oy, Substation Automation Products assumes no responsibility for any error that may appear in this document.
ABB Oy Substation Automation Products FI-65100 Vaasa, Finland Tel. +358 10 2211 Fax +358 10 2241599 www.abb.com/substationautomation
